Search

Short-term load forecasting (STLF) is the basis of power system planning and operation. With regard to the fast-growing load in China, a novel two-stage hybrid forecasting method is proposed in this paper. In the first stage, daily load is forecasted by time-series methods; in the second stage, the deviation caused by time-series methods is forecasted considering the impact of relative factors, and then is added to the result of the first stage. Different from other conventional methods, this paper does an in-depth analysis on the impact of relative factors on the deviation between actual load and the forecasting result of traditional time-series methods. On the basis of this analysis, an adaptive algorithm is proposed to perform the second stage which can be used to choose the most appropriate algorithm among linear regression, quadratic programming, and support vector machine (SVM) according to the characteristic of historical data. These ideas make the forecasting procedure more accurate, adaptive, and effective, comparing with SVM and other prevalent methods. The effectiveness has been demonstrated by the experiments and practical application in China. [ABSTRACT FROM PUBLISHER]

A load model is one of the most important elements in power system simulation and control. Recently, the constant impedance, constant current, and constant power load in combination with the induction motor load have been widely used as the composite load model, whose parameters are all identified from the field measurements in measurement-based load modeling practices so far. However, there is virtually no research conducted on whether all these parameters could really be identified. This paper investigates the possibility on reducing the number of composite load model parameters to be identified from field measurements. This paper first shows that direct application of the IEEE load motor parameters in the composite load model may be inadequate on describing the load dynamics over different operating status. Then the perturbation method is used to derive the trajectory sensitivities of the equivalent motor parameters, based on which the reduction on the identified parameters of the composite load model is presented. Two cases of measurement-based load modeling in North China and Northeast China are studied to illustrate the validity of the reduction method. It is shown that the reduction does not lose the model's capability on describing the load dynamics. The reduction on the number of identified parameters not only provides a possible way to solve the multi-valued load model problem based on the current practices on measurement-based load modeling, but it also facilitates building of the load model with more components included in it. Meanwhile, reducing the identified parameters reduces the identification time; thus, the proposed strategy significantly enhances the efficiency of the load modeling work. [ABSTRACT FROM AUTHOR]

Due to the uneven geographical distribution between load and wind power, currently it is difficult to integrate the large-scale wind power into the State Grid in China. There are significant wind curtailments for wind farms due to system restrictions. This paper proposes a new way of utilizing wind power, i.e., in-situ consumption, as an alternative to the costly development of long-distance transmission of large-scale wind power. Electrolytic aluminum load, which is one of the most typical high energy consuming loads, is employed to absorb the excess wind power in western China. An actual isolated industrial power system for aluminum production driven by wind power and coal-fired power is described. The penetration level of wind power in the isolated power system is up to 48.8%. The power imbalance between generation and load demand caused by wind power fluctuation or the tripping of coal-fired generators can dramatically impact the frequency stability of the isolated power system, which is of small inertia. An online identification method of power imbalance based on Wide Area Measurement System (WAMS) is presented. According to the characteristics of the electrolytic aluminum load, a system frequency control method by regulating the bus voltages of aluminum loads to eliminate the power imbalance is introduced. The simulation is done in Real Time Digital Simulator (RTDS) and the results verify the validity of the proposed frequency control method. [ABSTRACT FROM PUBLISHER]

The Shangdu power plant has four 600-MW turbine-generators connected to the North-China Grid through two 500-kV transmissions, which are compensated with 45% fixed series capacitors. Extensive studies conducted on the system model indicate that the system suffers from multimodal subsynchronous resonance (SSR). To solve the problem, a countermeasure is developed by combining the supplementary excitation damping control (SEDC) and the torsional stress relay (TSR). In this paper, the characteristics of the SSR problem are investigated. Then the developed SEDC is presented. To validate the effectiveness of the proposed SEDC as well as the results of model studies, field tests were conducted under various operating conditions. The tests fully exposed the realistic threat of SSR in the system. Meanwhile, it is demonstrated that the developed SEDC can improve torsional damping significantly, and thus solve the multimodal SSR problem effectively. This is the first time in China that practical SEDCs have been developed and their ability to mitigate multimodal SSR has been verified in a real series-compensated system. [ABSTRACT FROM AUTHOR]

Climate change poses a huge threat to human welfare. Hence, developing a low-carbon economy has become a prevailing and inevitable trend. Decarbonization of power generation, especially converting the current power mix into a low-carbon structure, will be a critical option for CO2 emission mitigation. In this paper, an integrated power generation expansion (PGE) planning model towards low-carbon economy is proposed, which properly integrates and formulates the impacts of various low-carbon factors on PGE models. In order to adapt to the characteristics of PGE models based on low-carbon scenario, a compromised modeling approach is presented, which reasonably decreases complexities of the model, while properly keeping the significant elements and maintaining moderate precision degree. In order to illustrate the proposed model and approach, a numerical case is studied based on the background of China's power sector, making decisions on the optimal PGE plans and revealing the prospects and potentials for CO2 emission reduction. [ABSTRACT FROM AUTHOR]

Load model is one of the most important elements in power system simulation and control. Based on more than 20 years of practice using load characteristic recorders in the measurement-based load modeling, this paper proposes the Expectation Composite Load Model to predict unseen data. The methods for load bus classification and parameter identification are also provided. The generalization capability of the proposed load modeling is validated by the measured load dynamics and system dynamics during two three-phase short circuit tests of the NE power grid in China. In order to evaluate the measurement-based load model, the Probabilistic Collocation Method (PCM) is applied to quantitatively analyze uncertainties of the simulation responses raised by the parameters. [ABSTRACT FROM AUTHOR]

Failure probability of system components may vary with the changes of weather, environment and other operation conditions. The time-varying or condition-based failure probability can be represented using a fuzzy model. Based on credibility theory, this paper presents a novel operation risk assessment method to handle the two-fold uncertainty combining randomness and fuzziness in power system operations. In the proposed method, a random fuzzy model is developed to accommodate impacts due to various operation conditions and other factors on the failure probability of system components. The WECC nine-bus system, IEEE 14-bus system and an actual power system in Northeast China were used to demonstrate feasibility and applicability of the presented method. The operation risk assessment module using the proposed method has been embedded in the EMS system in a district control center of a power company to perform real-time operation risk assessment. [ABSTRACT FROM AUTHOR]