Search

This experimental study investigated the influence of different turbine guide vane parameters on the ignition limit and light-round processes in a triple-dome combustor. It was found that for the triple-dome combustor, the minimum fuel/air ratios at the ignition limit all show a trend of initial decrease followed by subsequent increase with the growth of incoming air mass flow rate. The ignition fuel/air ratio decreases with the increase in turbine blockage ratio, and the optimal scheme is achieved with a blockage ratio of 0.8. Under the condition where the incoming air mass flow rate is 0.089 kg/s, the light-round time decreases with the increase in fuel/air ratio, and the light-round time of the combustor without guide vanes is shorter than that of the other schemes. With the increase in incoming air mass flow rate, the light-round time of the schemes with guide vanes is shortened. Under the same incoming air mass flow rate and fuel/air ratio, the increase in the blockage ratio will lead to an increase in the light-round time of the triple-dome combustor. [ABSTRACT FROM AUTHOR]

Lithium-ion batteries (LIBs) are employed in a range of devices due to their high energy and power density. However, the increased power density of LIBs raises concerns regarding their safety when subjected to external abuse. The thermal behavior is influenced by a number of factors, i.e., the state of charge (SoC), the cell chemistry and the abuse conditions. In this study, three distinct cylindrical Li-ion cells, i.e., lithium nickel cobalt aluminum oxide (NCA), lithium titanate oxide (LTO), and lithium iron phosphate (LFP), were subjected to thermal abuse (heating rate of 5 °C/min) in an air flow reactor, with 100% SoC. Venting and thermal runaway (TR) were recorded in terms of temperature and pressure, while the emitted products (gas, solid, and liquid) were subjected to analysis by FT-IR and ICP-OES. The concentrations of the toxic gases (HF, CO) are significantly in excess of the Immediate Danger to Life or Health Limit (IDLH). Furthermore, it is observed that the solid particles are the result of electrode degradation (metallic nature), whereas the liquid aerosol is derived from the electrolyte solvent. It is therefore evident that in the event of a LIB fire, in order to enhance the safety of the emergency responders, it is necessary to use appropriate personal protective equipment (PPE) in order to minimize exposure to toxic substances, i.e., particles and aerosol. [ABSTRACT FROM AUTHOR]

This study presents the potential of using a natural ventilation system integrated with different combinations of enhancement techniques. The focus was on the perspective of using such configurations of passive ventilation systems (PVSs) in buildings located in different European cities. This work presents the results of obtaining the level of volumetric air flow rate for considering natural ventilation systems. Furthermore, the influences of local weather conditions (temperature, solar radiation, wind speed) were analyzed. Moreover, the year-round operation of all systems was presented. Also noted was the limitation of using PVSs based on the natural draft effect, additionally assisted by wind turbine ventilators in all European localizations. However, for the cities located in the northern part of Europe, it was confirmed that such a system can still meet minimum hygienic recommendations. It was also noted that a system additionally supported by a solar chimney is a much better solution. The best system was a PVS supported by a wind turbine ventilator and solar chimney integrated with PCM accumulation mass. The system should be additionally supported by waste heat from low-temperature sources. In the presented study, a high potential to reduce CO2 emission from building stock by the recommended system is additionally highlighted. However, there is still a need to analyze the proposed solutions by additional field tests and experimental investigations. [ABSTRACT FROM AUTHOR]

The air humidification-dehumidification (HDH) technique for water desalination can be useful in many water production applications. Researchers from all around the world have examined various implementations of this technology to improve it. The present research investigates the effect of three dehumidifier coolants on the system. These coolants include water, helium, and hydrogen. The impact of these coolants on the parameters of the humidification-dehumidification desalination system will be discussed. The investigation's parameters are tested at various mass ratios, air flow rates, and air outlet heaters. The results show that when hydrogen is employed as a dehumidifier coolant, the gained output ratio (GOR) achieves its peak of 6.37 in the considered mass ratio range of 2.1 to 3. On the other hand, when hydrogen is utilized as a dehumidifier coolant, the system produces the maximum entropy, with the dehumidifier contributing the most. When the mass ratio changes from 2 to 3, the average entropy generation for the system using hydrogen in the dehumidifier increases by 3.8 and 2.9 times, respectively, compared to the average entropy generation for the system using water and helium. However, when hydrogen is used as a dehumidifier coolant, safety concerns must be addressed, as well as the size and cost of heat exchangers in comparison to water. [ABSTRACT FROM AUTHOR]

Drying and sanitising equipment has been very common in industrial plants since the pandemic. These are devices that consume significant amounts of energy. The best solution is to use a drying chamber equipped with a heat pump, which allows partial recovery of the energy. In the design of the drying chamber, the drying time is important, which depends both on the parameters of the heat pump itself, and the geometry and airflow of the drying chamber. The geometry and airflow supply should be arranged to ensure a uniform distribution of velocity throughout the drying area. For this purpose, the use of CFD simulations has been proposed. A model was developed in ANSYS/FLUENT where all model parameters, including the optimal mesh density, turbulence models, etc., were determined. The model was verified on the experimental results of the basic design of the chamber. Then an innovative design was proposed that was modelled and optimised in terms of the distribution of the inlet's perforation. The final design was made, and, at the same time, the simulation's results were verified by measuring the velocity of airflow in the new design. Together with the optimisation of the heat pump, this made it possible to reduce the drying time by 50%, with a simultaneous reduction in the energy consumed. [ABSTRACT FROM AUTHOR]

The energy reduction in chillers has been considered an important factor in the energy efficiency improvements of cooling systems, and water-side free cooling is regarded as the key of chiller free cooling technology. Therefore, this research aims to develop a control methodology for the extension of the free cooling operation time in order to improve the efficiency of water cooling-type chillers based on a WSE (water-side economizer) system for a data center and review the proper control conditions through an energy usage analysis of the entire system. The suggested methodology is an increase in the chilled water supply and return temperature according to the increase in the CARH (Computer Room Air Handler) fan air flow and a decrease in the chilled water flow. A case study was conducted according to the application of control through an EnergyPlus simulation. The results of the simulation show that energy usage was reduced by 8.1% under 120% CRAH fan capacity and 100% chilled water flow conditions. When applying the control plan, the free cooling period was extended according to the increased CRAH fan capacity and decreased chilled water flow. However, the increase in the CRAH fan energy must be considered. Also, in the case of a reduction in the chilled water flow, it is necessary to consider a point that can guarantee the cooling treatment heat rate in the heat exchanger. [ABSTRACT FROM AUTHOR]

An air-based photovoltaic thermal collector (PVTC) is a system that generates both electricity and heat using air flowing over a photovoltaic (PV) module. This system offers the advantage of easy maintenance; however, it suffers from lower thermal efficiency compared to other PVTCs, mostly owing to the low heat capacity of air. Thus, this study introduces a novel PVTC incorporating dual ducts and semicircular turbulators, which were experimentally evaluated under actual weather conditions in the Republic of Korea. The proposed PVTC was compared with two other types of PVTC: one is a single-duct PVTC with semicircular turbulators, and the other is a dual-duct PVTC without turbulators. The results showed that the thermal efficiency of the proposed PVTC increased by approximately 88.7% compared to the single-duct PVTC with a turbulator and by 9.3% compared to the dual-duct PVTC without a turbulator. The electrical efficiency showed a slight decrease of about 7.2% compared to the single-duct PVTC but an increase of 1.4% compared to the dual-duct PVTC without a turbulator. Overall, the total efficiency of the proposed PVTC increased by 54.2% and 7.7% compared to the single-duct PVTC and the dual-duct PVTC without a turbulator, respectively. These experimental results demonstrate that attaching dual ducts and semicircular turbulators to an existing PVTC increases the daily thermal energy output, which ultimately enhances the total daily energy output. [ABSTRACT FROM AUTHOR]

Achieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion and allowing the maximum temperature to be reached faster. This work examines the energy conversion in sandwiched glassy platforms with gold nanorods. The platforms are kept vertically in the air and illuminated by a 0.5 W near-infrared laser (808 nm). To describe this aspect theoretically, the size and conversion efficiency of the electromagnetic properties are compromised between the proposed model and the stability of the nanorods. As a research approach, our model of cross-sections and polarizability for the surface effect is proposed, coupled with classical CFD numerical calculations. The results of the proposed model, validated by a thermal camera and spectroscopy measurements, indicate that as long as the energy conversion is visible with relatively low-power lasers (ΔT = 18.5 °C), the platforms do not offer fast heat dissipation. The results indicate that, despite the flow forcing by the air inflow, the entropy generation due to heat conduction is more than three orders higher than the dynamic entropy production. Flow forcing corresponds to the value of the velocity for classical convective motions. Therefore, the delivered heat flux must be distributed via convective transport or the associated high-conductive materials. [ABSTRACT FROM AUTHOR]

The two-phase countercurrent flow limitation (CCFL) in horizontal channels is important in relation to nuclear reactor safety. In this study, we aim to investigate the CCFL characteristics and the flow behaviors in horizontal circular pipes with small diameters. The effects of pipe diameter and the water head in the upper plenum on CCFL characteristics are experimentally studied. An image-processing technique and statistical treatments are implemented to analyze the horizontal countercurrent flow. The results show that the CCFL characteristics for the horizontal circular pipes with small diameters can be well correlated using the dimensionless parameters, which are based on adding fluid viscosity to the Wallis parameters. The CCFL characteristics are significantly affected by the pipe diameter and are slightly affected by the water head above the horizontal pipe. The gas–liquid interface fluctuates with certain periods, and flow pattern transitions happen in the horizontal air–water countercurrent flow. As the air flow rate increases, the occurrence location of the liquid slug appears to shift towards the water entrance. In addition, the further away from the water entrance, the lower the average of liquid holdup. [ABSTRACT FROM AUTHOR]

The energy harnessing from flow-induced vibrations (FIV) by an oscillating foil placed tandemly behind a circular cylinder (which serves as a vortex generator) is investigated. The foil is submerged in the wake produced by the fixed cylinder and could oscillate in the direction perpendicular to the incoming flow with single-degree freedom. The spacing ratio ranges from 1.0 to 5.0. The oncoming fluid velocity is U = 1–10 m/s, corresponding to the reduced velocity Ur = 3.81–38.08 and the Reynolds number Re = 9.58 × 103–9.58 × 104. Four harnessing damping ratios (ζharness = 0.0054–0.0216) are used to simulate the energy conversion conditions. The main conclusions are: (1) The optimal oscillation pattern related to the highest harnessed energy emerges as the spacing ratio close to 1.0. (2) The airflow energy converted by the foil is positively correlated with the harnessing damping ratio because the amplitude responses are similar at various harnessing damping ratios. A high velocity yields the highest harnessed power. (3) The harnessing efficiency of the foil could reach 48.89%, which is much more than that of an isolated flapping foil. [ABSTRACT FROM AUTHOR]

An unmanned underwater vehicle (UUV) powered by a compressed air power system is proposed to address challenges for battery/motor-powered vehicles under high-speed navigation, long endurance, and high mobility. These vehicles actively utilize supercavitation drag reduction by the exhausted gas from the compressed air power system. MATLAB/Simulink and FLUENT are used to establish theoretical models of the compressed air power system and ventilation supercavitation. The relationship between system power and navigation resistance is examined with different air flows, along with a comparison of endurance of different power vehicles at various speeds. The issue of the endurance-enhancing effect of supercavitation at high speed is investigated. The results demonstrate that increasing the air flow leads to higher power and reduced navigation resistance, and there is a balance between them. Furthermore, compared to the battery-powered vehicles with equal energy storage capacity, the compressed air power system shows 210.08% to 458.20% longer endurance times at speeds of 30 kn to 60 kn. Similarly, considering equal energy storage mass, it achieves 42.02% to 148.96% longer endurance times at high speeds (30 kn to 60 kn). The integration of supercavitation and air-powered systems can greatly enhance the endurance and maneuverability of the vehicle at high speeds while ensuring a compact system structure. The investigations could offer valuable ideas for the development and application of compressed air power systems for UUV at 30 kn to 60 kn or higher maneuvering. [ABSTRACT FROM AUTHOR]

Air compressors are widely used in industrial fields. Compressed air systems aggregate air flows and then supply them to places of demand. These huge systems consume a significant amount of energy and generate heat internally. Machine components in compressed air systems are vulnerable to heat, and, in particular, a radiator to cool the heat of the overall air compressor is the core component. Dirty radiators increase energy consumption due to anomalous cooling. To reduce the energy consumption of air compressors, this mechanism emphasizes a machine learning-based radiator fault detection, using features such as RPM, motor power, outlet pressure, air flow, water pump power, and outlet temperature with slight true fault labels. Moreover, the proposed system adds an LSTM-based motor power prediction model to point out the initial judgment of radiator fault possibility. Via the rigorous analysis and the comparison among machine learning models, this meticulous approach improves the performance of radiator fault prediction up to 93.0%, and decreases the mean power consumption of the air compressor around 2.24%. [ABSTRACT FROM AUTHOR]

Air velocity is one of the key parameters affecting the sensation of thermal comfort. In mixing ventilation, the air is most often supplied above the occupied zone, and the air movement in a room is caused by jets that generate recirculating flows. An effective tool for predicting airflow in a room is CFD numerical modeling. In order to reproduce the air velocity distribution, it is essential to select a proper turbulence model. In this paper, seven Eddy–Viscosity RANS turbulence models were used to carry out CFD simulations of a sidewall air jet supplied into a room through a wall diffuser. The goal was to determine which model was the most suitable to adopt in this type of airflow. The CFD results were validated using experimental data by comparing the gross and integral parameters, along with the parameters of the quasi-free jet model. The numerical results obtained for Std k-ε and EVTM models were most consistent with the measurements. Their error values slightly exceeded 15%. On the contrary, the k-ω and RNG k-ε models did not reproduce the quasi-free jet parameters correctly. The research findings can prove beneficial for simulating air distribution in supplied air jets during the initial conceptual phases of HVAC system design. [ABSTRACT FROM AUTHOR]

The aerodynamic shapes of the blades are of great importance in wind turbine design to achieve better overall turbine performance. Fluid–structure interaction (FSI) analyses are normally carried out to take into consideration the effects due to the loads between the air flow and the turbine structures. A structural integrity check can then be performed, and the structural/material design can be optimized accordingly. In this study, three different tip shapes are investigated based on the original blade of the test wind turbine (Phase VI) from the National Renewable Energy Laboratory (NREL). A one-way coupled simulation of FSI is conducted, and results with a focus on stresses and deformations along the span of the blade are investigated. The results show that tip modifications of the blade have the potential to effectively increase the power generation of wind turbines while ensuring adequate structural strength. Furthermore, instead of using more complicated but computationally expensive techniques, this study demonstrates an effective approach to making quality observations of this highly nonlinear phenomenon for wind turbine blade design. [ABSTRACT FROM AUTHOR]

In this article, the control of a DC/DC converter was carried out using the proposed methods of conventional PI, PSO-based PI, PSO-based FOPI, GA-based PI, and GA-based FOPI controllers in order to improve the performance of PEMFCs. Simulink models of a PEMFC model with two inputs—hydrogen consumption and oxygen air flow—and with controllers were developed. Then, the outputs of a system based on conventional PI were compared with the proposed methods. IAE, ISTE, and ITAE were employed as fitness functions in optimization algorithms such as PSO and GA. Fitness function value, maximum overshoot, and rising time were utilized as metrics to compare the performance of the methods. PI and FOPI parameters were optimized with the proposed methods and the results were compared with traditional PI in which the optimum parameters were determined by an empirical approach. This research study indicates that the proposed methods perform better than the conventional PI method. However, it becomes apparent that the GA-FOPI approach outperforms the others. The simulation result also shows that the PEMFC model with conventional PI and FOPI controllers in which the controller parameters are tuned using PSO and GA has an acceptable control performance. [ABSTRACT FROM AUTHOR]

This paper presents methodologies and equipment for SI-traceable inline measurements of water content (a critical quality parameter) in solid biofuels. Inline measurement systems for water content are commonly used at CHP plants, providing continuous real-time data. However, the accuracy of these systems is in most cases unsatisfactory, mainly because the systems are not calibrated representatively for the relevant material, and until now, calibrations traceable to the SI system have not been available. To provide reliable and accurate inline water content data, new procedures and equipment for calibrating measurement systems were developed. Two reference methods for the determination of water content were developed; one measures the airflow and dewpoint of desorbed water in the air passing a test sample, while the other uses a P2O₅-sensor. Additionally, a transfer standard based on a cavity resonance sensor was developed for fast onsite calibration of the inline sensor at the power plant. This new instrument allows for quick and accurate measurements. The transfer standard is made metrologically traceable to the primary measurement standards. The entire system was demonstrated by calibrating an inline microwave-based (MW) sensor at the CHP plant of VERDO in Randers, Denmark. Thus, a complete metrological traceability chain was established from an industrial to a primary standard. [ABSTRACT FROM AUTHOR]

With the increasing popularity of yachting sports and races comes the need to develop a more advanced and efficient propulsion device. Significant improvement can be made when using a mainly lift-driven propulsion source, known as a wing sail. This idea, dating back as far as the mid-70s, is nowadays regaining interest as a propulsion system in multihull, high-performance racing vessels (for instance, the AC50 and AC72 America's Cup yacht classes). This article documents 2D and 3D numerical analyses of wing sail systems imitating those of an AC72 racing yacht class. It depicts methods employed in two- and three-dimensional steady-state flow simulations, compares systems equipped with various geometries of mainsails, and details a comprehensive examination of the airflow around the vessel using spatial analyses. Numerical calculations were carried out using ANSYS CFX and ANSYS Fluent (with overset feature) for 2D and 3D models, respectively. All simulations were conducted under conditions similar to those acting on the real system, i.e., high Reynolds number (order of magnitude 106 to 107) and atmospheric boundary layer (in the 3D model). [ABSTRACT FROM AUTHOR]

Passive solar systems are one of most important strategies to reduce the heating loads of buildings. The Trombe–Michel (TM) wall and its variants are some of the better-known structures in the field of solar systems. An alternative to the TM wall is the Barra–Costantini (BC) system. In the present paper, CFD numerical simulations, both in steady and transient states, of modified BC and TM walls were carried out in the winter season. Different interspace thicknesses were simulated in order to evaluate their effects on the temperature field and air velocity, and the numerical results were compared among them. It was found that the BC system offers greater hot air flow compared with the TM wall; the mass flow rate increased up to 43% in the BC system and up 28% in the TM system when the interlayer thickness was increased by 500%. The transient simulations (100 h simulated) demonstrated that the dynamic response of the BC wall was shorter than that of the TM wall, even when the TM wall was simulated with initial thermal conditions that were more advantageous than those for the BC wall. The BC system reached a periodic stabilized regime within 24 h, whereas the TM system failed to stabilize in 100 h. The results show that for both TM and BC structures, the interlayer thickness scarcely influenced the temperature of the environment reached (the temperature peak increased up to 3–4% as the interlayer thickness was increased by 500%), while larger air speed changes were observed in the BC system in the transient state compared with the TM system. Thus, in the TM system, the outlet air velocity was practically constant as the interlayer thickness was increased; in contrast, the outlet velocity peak increased up to 50% in the BC system. Moreover, the BC wall presented a quicker response to satisfy the ambient thermal loads. [ABSTRACT FROM AUTHOR]

The air compressor holds paramount importance due to its significant energy consumption when compared to other Balance of Plant components of polymer electrolyte membrane (PEM) fuel cells. The air supply system, in turn, plays a critical role in ensuring the stable and efficient operation of the entire fuel cell system. To enhance system efficiency, the impact of varying the stoichiometric ratio of air and air pressure was observed. This investigation was carried out under real loading conditions, replicating the conditions experienced by the power module when fuel cells are in use within a forklift. The air compressor can be operated at different pressure and excess air ratios, which in turn influence both the fuel cell's performance and the overall efficiency of the power module system. Our research focused on assessing the performance of PEM fuel cells under different load cycles, adhering to the VDI60 requirements for forklift applications. This comprehensive examination encompassed the system's minimum and maximum load scenarios, with the primary goal of optimizing excess air and pressure ratio parameters, especially under dynamic load conditions. The results revealed that higher air pressures and lower excess air ratios were conducive to increasing system efficiency, shedding light on potential avenues for enhancing the performance of PEM fuel cell systems in forklift applications. [ABSTRACT FROM AUTHOR]