Search

A well-designed support material between catalyst and substrate can always significantly enhance the performance of an electrode on water oxidation. In this work, a functional Ni and N-doped carbon layer (NNC) was designed on carbon paper (CP) via pyrolysis by using a controlled electrodeposited polyporphyrin as a precursor. Consequently, the fabricated NiFe-LDH/NNC/CP achieved a catalytic current density of 100 mA cm−2 at a small overpotential of 231 mV with a low Tafel slope of 26.0 mV dec−1, as well as high durability for more than 360 h. The insights are that N-doping reinforces the hydrophilicity and the catalyst binding capacity, while Ni-doping intensifies the conductivity. [ABSTRACT FROM AUTHOR]

Hybrid water electrolysis (HWE) is a promising pathway for the simultaneous production of high-value chemicals and clean H2 fuel. Unlike conventional electrochemical water splitting, which relies on the oxygen evolution reaction (OER), HWE involves the anodic oxidation reaction (AOR). The AORs facilitate the conversion of organic or inorganic compounds at the anode into valuable chemicals, while the cathode carries out the hydrogen evolution reaction (HER) to produce H2. Recent literature has witnessed a surge in papers investigating various AORs with organic and inorganic substrates using a series of transition metal-based catalysts. Over the past two decades, metal–organic frameworks (MOFs) have garnered significant attention for their exceptional performance in electrochemical water splitting. These catalysts possess distinct attributes such as highly porous architectures, customizable morphologies, open facets, high electrochemical surface areas, improved electron transport, and accessible catalytic sites. While MOFs have demonstrated efficiency in electrochemical water splitting, their application in hybrid water electrolysis has only recently been explored. In recent years, a series of articles have been published; yet there is no comprehensive article summarizing MOFs for hybrid water electrolysis. This article aims to fill this gap by delving into the recent progress in MOFs specifically tailored for hybrid water electrolysis. In this article, we systematically discuss the structure–property–performance relationships of various MOFs utilized in hybrid water electrolysis, supported by pioneering examples. We explore how the structure, morphology, and electronic properties of MOFs impact their performance in hybrid water electrolysis, with particular emphasis on value-added chemical generation, H2 production, potential improvement, conversion efficiency, selectivity, faradaic efficiency, and their potential for industrial-scale applications. Furthermore, we address future advancements and challenges in this field, providing insights into the prospects and challenges associated with the continued development and deployment of MOFs for hybrid water electrolysis. [ABSTRACT FROM AUTHOR]

In this paper, we provide a novel electrode switch (ES) method to improve the stability of the alkaline electrolyzer toward water splitting. The voltage of the alkaline electrolyzer consisting of commercial Ni mesh electrodes utilizing the ES mode exhibits extreme stability because highly active Ni oxide(hydroxide) with oxygen defects is in situ formed during the hydrogen evolution reaction (HER) polarization process. [ABSTRACT FROM AUTHOR]

Benefiting from a high overpotential of the competitive hydrogen evolution reaction with a carbon paper cathode, the desired electrochemical reduction of imines was achieved with high faradaic efficiency by using H2O as a H-source. With this sustainable atom-economic strategy, a series of potentially versatile amines were obtained in medium-to-high yields (49–86%). [ABSTRACT FROM AUTHOR]

Here, polyaniline (PANI) is reported loaded on carbon paper to modify the carbon paper-PANI-Pt electrode surface, tailoring the electrocatalytic capability towards the hydrogen evolution reaction and ethanol oxidation reaction. The reasons for the enhancement by the PANI layer are attributed to the hydrophilic electrode surface, uniform dispersion of Pt, and large electrochemical active surface. [ABSTRACT FROM AUTHOR]

In this paper, a series of micro–nano reactors assembled by N doped carbon coated TiO2 heterojunction nanosheets with different thickness, named TiO2/N–C hollow framework (HF), TiO2/N–C hollow hexahedron assembled by nanosheets (HHS), and TiO2/N–C hollow hexahedron assembled by ultrathin nanosheets (HHUS), have been prepared by adjusting the alcoholysis rate of NH2-MIL-125 and then pyrolysis. Experimental and theoretical studies revealed that with the decrease of the thickness of the heterojunction nanosheet subunit, more low-coordination Ti atoms would be exposed as effective sites for photocatalytic H2 evolution, and the interaction between the carbon layer and TiO2 would also be enhanced, which provided a smooth migration path for the effective separation of photogenerated carriers. Thus, TiO2/N–C HHUS with the thinnest nanosheet subunit exhibited the best photoelectric performance and the highest photocatalytic hydrogen production activity. [ABSTRACT FROM AUTHOR]

The rational design of high-efficiency electrocatalysts for application in water oxidation in alkaline media remains a great challenge. In this paper, Ni3+-rich nanograss-like Mo-doped Ni3S2/NiS/VS arrays grown on nickel foam (denoted as Mo-NiVS@NF) have been successfully constructed through a hydro/solvothermal method. Interestingly, Mo-NiVS@NF exhibits superior catalytic OER performance, needing an overpotential of 217 mV to drive a current density of 10 mA cm−2, outperforming most previously reported NiS-based electrocatalysts. The result indicates that the Ni3+-rich active sites caused by the modulation of the electronic structure environment via the introduction of V and high-valency Mo play an important role in the high activity for the OER. Moreover, this catalyst shows high long-term electrochemical durability. [ABSTRACT FROM AUTHOR]

Hydrogen energy is a promising energy source that is environmentally friendly due to its long-term, large-capacity storage and low greenhouse gas emissions. However, the mass production of hydrogen is still technically difficult due to limitations in efficiency, stability, and cost, even though it can satisfy all of the current energy demands. Water splitting using an electrocatalyst is an efficient method for environmentally friendly hydrogen production, and various catalyst-related studies are being conducted for this purpose. For the last decade, transition metal-based compositions have been at the center of water splitting catalyst research. Despite numerous studies and developments, studies on transition metal-based catalysts so far still have various problems to be solved. Although excellent review papers on transition metal-based catalysts have been reported, the overall scope of transition metal-based catalysts has rarely been covered in the reports. In this review, we present the research about overall transition metal-based electrocatalysts for hydrogen production from four different categories, namely, alloys, transition-metal dichalcogenides (TMDs), layered double hydroxides (LDHs), and single-atom catalysts (SACs). The fundamental roles of metal alloying and unique electrical properties of TMDs, LDHs, and SACs are mainly discussed. Furthermore, we present the recent advances in photovoltaic–electrochemical (PV–EC) systems for sustainable hydrogen production. Finally, perspectives on the issues to be addressed in the research on transition metal-based electrocatalysts are provided. [ABSTRACT FROM AUTHOR]

Efficient electrocatalysts are in great demand for renewable energy storage systems. Herein, we propose an ultrafast heating strategy to fabricate an efficient Ir/CP-UH catalyst for the oxygen evolution reaction (OER). Experimental results demonstrated that the ultrasmall Ir nanoparticles (≈1–3 nm) and clusters (<1 nm) were highly dispersed on the carbon paper support after a short thermal shock (∼5 s). The catalyst showed a low overpotential of 260 mV at 10 mA cm−2 and remarkable mass activity of about 13.8 times higher than that of the current state-of-the-art commercial Ir/C catalyst. This ultrafast heating strategy can also be applied to other catalyst systems for OER and other electrochemical reactions. [ABSTRACT FROM AUTHOR]

Porous materials are widely studied in many applications due to their high surface area and rich edge sites. Here, for the first time, we reported a simple and convenient method to synthesize porous nanosheets of metal hydroxides by selectively etching amphoteric Al in CoAl layered double hydroxides on carbon paper (CoAl-LDH/CP), and then convert them into porous cobalt phosphide nanosheets on carbon paper (p-CoP/CP) via low temperature phosphidation. In contrast to pristine cobalt phosphide nanosheets on carbon paper (CoP/CP), p-CoP/CP has lower overpotential, Tafel slope and charge transfer resistance as well as higher electrochemically active surface area. The excellent electrochemical characteristics make it have outstanding catalytic activity and stability over the whole pH range. In 1.0 M KOH, the p-CoP/CP only requires an overpotential of 57 mV to drive 10 mA cm−2. To achieve the same current density, it only needs overpotentials of 39 and 60 mV in 1.0 M H2SO4 and 1.0 M PBS, respectively. To our knowledge, it is the best among those nonprecious electrocatalysts used for hydrogen evolution in neutral solution. Moreover, this catalyst offers good durability over the whole pH range. [ABSTRACT FROM AUTHOR]

We demonstrate a lamellar NiMoCo@CuS catalyst, showing not only an excellent catalyst performance (η100@72 mV and a Tafel slope of 47 mV dec−1), but also a good stability (20 mA cm−2@30 hours), outperforming the NiMo system and noble Pt. [ABSTRACT FROM AUTHOR]