Search

Wind turbines are typically designed based on fatigue and serviceability limit states, but still require an accurate assessment of bearing capacity. Overconsolidated clay deposits in Canada often have a thin layer of crust with a relatively high undrained shear strength developed from weathering, desiccation, and geochemical processes. However, existing design methods only assess the bearing capacity using effective area and inclination factor without consideration of surficial crusts. This paper studies the undrained VHMT (vertical, horizontal, moment, and torsional) failure envelope of circular foundations founded on a surficial crust underlain by a uniform soil with a zero-tension interface condition using finite element analysis. An analytical expression for the VHMT failure envelope is derived. [ABSTRACT FROM AUTHOR]

Fourteen large landslides have occurred within a 10 km stretch of the Thompson River Valley south of Ashcroft, British Columbia. The slides have had movements ranging from rapid (metres per hour) to very slow, and the largest slides have volumes approaching 15.0 × 106 m3. Investigations of these slides have been conducted since the early failures of the slopes were noted in the 1860s, and have continued with the periodic reactivations and slope movements since then. This paper focuses on the Ripley Slide, which is one of the slides within the Thompson River Valley. This slide is a very slow-moving landslide, which has recently been reactivated. This landslide is crossed by a major transportation corridor and has therefore been the subject of ongoing geotechnical investigation and instrumentation. The results of this investigation are interpreted in light of the wealth of accumulated knowledge from more than a century of geotechnical investigation within this valley. The data collected from the landslide show that, like other slow-moving landslides in this valley, the seasonal fluctuations of the Thompson River elevation strongly influence the instability and the rate of slope movement. Continuous global positioning system monitoring of the movement of the landslide combined with measurement of the pore pressures within the sliding mass and elevation of the river have allowed for an empirical correlation between the limit equilibrium method modelled factor of safety and the velocity of the landslide. [ABSTRACT FROM AUTHOR]

The preconsolidation pressure and overconsolidation ratio profiles are the most important factors related to the mechanical behaviour of clay deposits. They are interpreted on the basis of a limited number of laboratory tests, but the near-continuous information provided by the piezocone can allow local data to be extrapolated to an entire site. Numerous methods have been proposed for relating piezocone data to preconsolidation pressure and the overconsolidation ratio, but their validity is still uncertain. In this paper, nine methods are compared on the basis of data collected on 31 sensitive clay sites in Quebec whose preconsolidation pressure profiles are well known. Each method is briefly presented and the most promising are identified. The simplest method, which directly relates preconsolidation pressure to net tip resistance, also appears to be the most effective.Key words: clay, preconsolidation pressure, overconsolidation ratio, piezocone, correlations.Les profils de pression de préconsolidation et du rapport de surconsolidation constituent les éléments les plus importants en ce qui concerne le comportement mécanique des dépôts argileux. Leur évaluation se fait par un nombre limité d'essais de laboratoire, mais les données fournies par le piézocône de manière presque continue peuvent permettre une extrapolation à l'ensemble du site de ces données locales. De nombreuses méthodes ont été proposées pour corréler les données du piézocône et la pression de préconsolidation ou le rapport de surconsolidation mais leur validité est encore incertaine. Dans le présent article, neuf méthodes sont examinées à partir de données provenant de 31 sites d'argile sensible de la province du Québec pour lesquels les profils de pression de préconsolidation sont bien connus. Chaque méthode est brièvement présentée et les méthodes les plus intéressantes sont identifiées. Il semble que la relation entre la pression de préconsolidation et la résistance en pointe nette, qui est la plus simple, est aussi la plus efficace.Mots clés : argile, pression de préconsolidation, rapport de surconsolidation, piézocône, corrélations. [ABSTRACT FROM AUTHOR]

To analyze the effects of strain rate and viscoplastic strain on consolidation of natural clay, this paper presents a nonlinear viscoplastic model in which viscoplastic behaviour is modeled by a unique effective stress (σ'[sub v] ) – viscous strain (ℇ[sub v] ) – viscous strain rate (ℇ[sup ·] [sub v] ) relationship. The proposed model can consider the effects of strain rate and viscoplastic strain on consolidation, to take into account the difference in strain rate between laboratory and field conditions, and the combined processes of generation and dissipation of pore pressure during consolidation. This model can also predict the behaviour of clay during stepwise loading, constant rate of strain, and relaxation of effective stress. The predicted values using numerical analysis are compared with measured values in laboratory tests and in situ, under an embankment built on soft clay at Berthierville, Quebec. It is possible to estimate the consolidation behaviour of natural clay with reasonable accuracy using the proposed nonlinear viscoplastic model.Key words: consolidation, soft clay, strain rate, viscoplastic, relaxation.Dans le but d'analyser les effets de la vitesse de déformation et de la déformation viscoplastique sur la consolidation de l'argile naturelle, cet article présente un modèle viscoplastique non linéaire dans lequel le comportement est modélisé par une relation unique contrainte effective-déformation visqueuse-vitesse de déformation visqueuse σ'[sub v] – ℇ[sub v] – ℇ[sup ·] [sub v] . Le modèle proposé peut prendre en considération les effets de la vitesse de déformation et de la déformation viscoplastique sur la consolidation pour tenir compte de la différence dans les vitesses de déformation entre les conditions en laboratoire et sur le chantier, de même que les processus combinés de génération et de dissipation de la pression interstitielle durant la consolidation. Ce modèle peut aussi prédire le comportement de l'argile en incluant le chargement par étape, la vitesse de déformation constante, et la relaxation de la contrainte effective. Les valeurs prédites au moyen de l'analyse numérique sont comparées avec celles mesurées dans les essais en laboratoire et in situ sous un remblai construit sur de l'argile molle à Berthierville, Québec. Il est possible d'estimer le comportement en consolidation de l'argile naturelle avec une précision raisonnable au moyen du modèle viscoplastique non linéaire proposé. Mots clés : consolidation, argile molle, vitesse de déformation, viscoplastique, relaxation.[Traduit par la Rédaction] [ABSTRACT FROM AUTHOR]