Search

Plasterboard, a commonly utilized construction material, comprises a gypsum core nestled between two paper layers. Gypsum after demolition of plasterboards is a recyclable waste that has been reused into new plasterboard or other purposes such as agricultural products. However, there is a lack of understanding on the potential for recycling the paper layers. This study investigates the use of wastepaper fibers, obtained from the paper layers, as a reinforcing material and metakaolin as a partial cement replacement material in concrete. This study demonstrates the ability of the paper from waste plasterboard for reinforcing concrete. Wastepaper fibers were used at different concentrations ranging from 0 to 2.5% by weight of binder. Bending test was conducted for assessing fracture behavior of concretes, including load bearing capacity, modulus of rupture, crack mouth opening displacement (CMOD) at the load bearing capacity, fracture toughness, and fracture energy. Slump, axial compression, and scanning electron microscopy (SEM) were also conducted on the concretes. It is found that incorporating wastepaper fiber by up to an optimum content of 1.5% results in an increase in the compressive strength (57%), flexural load bearing capacity and modulus of rupture (31%), CMOD displacement at load capacity (14%), fracture toughness (37%), and fracture energy (73%) of the metakaolin‐based concrete. However, further increase in the wastepaper fiber content results in decreased mechanical properties of the concrete, which is due to the fiber agglomeration and non‐uniform distribution within the concrete matrix. Based on the results, the concrete with 20% metakaolin and 1.5% wastepaper fiber experiences similar mechanical properties to the conventional concrete. The results of this study underscore the substantial potential of leveraging waste materials such as wastepaper and by‐products like metakaolin to diminish reliance on conventional cement. This approach not only enhances the mechanical properties of concrete but also fosters sustainable building practices by promoting the recycling of waste materials, reducing carbon footprint, and mitigating the environmental impacts inherent in traditional concrete production. [ABSTRACT FROM AUTHOR]

The paper portrays a comprehensive computational procedure for determining the global structural resistances of two existing bridges made of I‐73 and KA‐61 precast post‐tensioned concrete girders using advanced statistical assessment methods in combination with nonlinear fracture mechanics‐based finite element method analysis. Although this combination is a powerful tool for realistic modeling of structures, its practical application is still very time consuming. Therefore, a statistical sampling approach for the determination of the structural design resistance is compared to selected efficient semi‐probabilistic methods based on the estimation of coefficient of variation—estimation of coefficient of variation (ECoV) method according to fib Model Code 2010 and improved approach called Eigen ECoV method. Load‐bearing capacity is determined for the ultimate as well as several serviceability limit states. The sensitivity of the input parameters burdened with uncertainties on the response of the structure is quantified using a sensitivity analysis supported by a surrogate model based on polynomial chaos expansion. The paper shows that the applicability of nonlinear modeling with respect to uncertainties is possible when using these ECoV methods and a surrogate model and can be applied in a routine manner. The shortcomings and advantages of all the used safety design/assessment methods are discussed. [ABSTRACT FROM AUTHOR]

In modern construction, one of the most important factors in the execution of contracts is time. Standard procedures for assessing the frost resistance or concrete are usually very time‐consuming and can take up to 40 days. The current paper is experimentally and practically oriented. It presents an alternative testing method, based on air void network, that allows to assess the frost resistance of concrete within just a few days of taking the samples. X‐ray micro‐CT scans were introduced to obtain the quantitative and qualitative 3D information about the air void microstructure taking into account total air content: A (%), pores of the size below 300 μm in diameter content: A300 (%), specific surface of air voids: α (mm−1) and spacing factor: L (mm) to predict the freeze/thaw durability. To verify the assumptions of the frost resistance method, based on the analysis of pore microstructure, tests of freeze/thaw resistance in accordance with Polish supplement to European Standard were carried out. Presented research revealed that the appropriate microstructure of air pores, in particular, content of micropores with the diameter less than 0.3 mm: A300 combined with a spacing factor: L (mm) can constitute a reliable basis for determining concrete freeze/thaw durability. Thus, the method proposed in the current paper can be effectively used for fast and trustworthy determination of the air‐entrained concrete durability in a short time and without any special preparation of the tested sample that allows immediate preventive or repair actions to be taken if required. [ABSTRACT FROM AUTHOR]

This paper describes the use of joints with bent bars and postcast ultrahigh‐performance concrete (UHPC) joints to enable formwork‐free and support‐free construction of composite slabs. To investigate their flexural performance, static loading tests on three full‐scale simply‐supported slabs and one monolithic slab were carried out. Flexural capacity, stiffness, and crack development were recorded, resulting on flexural failure experienced by all specimens. Main cracks of composite specimens developed along the UHPC–normal concrete interface, and cracks on both sides of the UHPC joint developed evenly, similar with that of the monolithic specimen. Besides, composite slabs and a monolithic slab showed similar flexural capacity. UHPC joint was not cracked when failure occurred, and bottom bars were anchored and connected in the UHPC joint, proving that the flexural anchorage method is feasible. The average strain of the composite specimen across the UHPC joint was still consistent with the assumption of plain section, and there was an approximate linear relationship between the expansion width of the joint at the bottom of the slab and the maximum crack width at bottom bars. Moreover, middle bars contributed to the flexural capacity and stiffness of composite specimens, while horse stool reinforcement may effectively prevent the interface shear failure on the composite interface. Based on test results, the formula to control cracking of UHPC is given in this paper. The design methods on flexural capacity, stiffness, and expansion width of composite slabs are also presented and discussed. [ABSTRACT FROM AUTHOR]

In this paper, five specimens were designed to test under monotonic static loading to study the axial compression performance of steel tube‐reinforced high‐strength recycled aggregate concrete composite columns with steel bars. The design parameters for these specimens include the type of concrete, the sectional shape of the steel tube (circular or square), and the internal structure of the core column, specifically the presence or absence of cross‐shaped tie bars in the square steel tube. The effects of different parameters on the axial load–displacement curve, bearing capacity, and ductility were analyzed. The test results show that the failure of all specimens was caused by the concrete cover spalling of outer reinforced concrete, which occurred after the longitudinal strain of the steel tube exceeded the yield strain. The ultimate bearing capacity of the recycled aggregate concrete (RAC) specimen is higher than that of the natural aggregate concrete (NAC) specimen, but the latter has a more robust deformation performance. Furthermore, under the condition of the same steel tube cross‐sectional area and similar material strength, the bearing capacity and deformation capacity of specimens with circular steel tubes are higher than those of specimens with square steel tubes. A similar conclusion was also obtained for square steel tube specimens with cross‐shaped tie bars. Finally, four international design methods were applied to estimate the axial compression capacity of 40 composite columns, as detailed in this paper and other sources. [ABSTRACT FROM AUTHOR]

The current paper presents an innovative form of the cold‐formed U‐shape steel encasing concrete composite beam (CUCB). The suggested CUCB consists of a cold‐formed U‐shaped steel encasing plain concrete beam which are connected to each other using continuous transversal threaded stud bolts. The experimental program consisted of eight beam specimens tested in the four‐point bending set‐up. One of them was a normal reinforced concrete beam and considered as a reference specimen while the remaining specimens were CUCB specimens without ordinary flexural and shear reinforcement. Four parameters were studied in this paper: (i) the thickness of the U‐shaped steel, (ii) the spacing between the stud bolts, (iii) the arrangement of the bolts, and (iv) the number of the bolt's rows. Results indicated an overall improvement in the load‐carrying capacity and stiffness of most CUCB specimens in comparison with the reference specimen. It was found that the using of three rows of bolts can significantly improve the ductility and toughness of the CUCB specimen in comparison with two rows of bolts. On the contrary, an increase in the bolt spacing entails a decrease in the CUCB specimens' toughness. [ABSTRACT FROM AUTHOR]

This paper investigates the strengthening of non‐ductile reinforced concrete (RC) columns using partial steel‐plate jacketing to enhance ductile capacity. Quasi‐static cyclic loading tests were conducted on three rectangular RC columns with varying shear‐span‐to‐depth ratios, evaluating the effectiveness of steel‐plate jacketing. Results show improved ductile flexural response, high drift capacity, and maintained gravity‐loading capacity under high lateral displacements. A numerical investigation, adopting a multi‐spring fiber section model, predicted cyclic lateral strength, drift ratio, and failure mode, accurately simulating reinforcement behavior and capturing the shear‐strength enhancement due to steel‐plate jacketing. Numerical results demonstrated good agreement with experimental findings. Based on these outcomes, a simple design procedure for retrofitted concrete columns, applicable to design engineers, has been developed and reported in this paper. This study contributes valuable insights into the practical applications of steel‐plate jacketing for non‐ductile RC column retrofitting, offering a comprehensive approach to predicting their seismic performance. [ABSTRACT FROM AUTHOR]

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements to estimate the stress in the bars. In existing structures, crack width formulations can be used to estimate the stress in the reinforcement from crack width measurements, profiting from additional information that can be measured in‐situ, such as the crack spacing. Recent experimental results show that the values of the mean bond stress typically considered in code formulations overestimate the actual bond stresses activated in cracked concrete specimens. This paper presents the results of an experimental program consisting of reinforced concrete ties and beams instrumented with Digital Image Correlation and fiber optical measurements. The results confirm the differences with typically assumed bond stresses. A formulation to estimate the bond stresses in service conditions is derived from the results of the numerical integration of a previously developed local bond–slip relationship. Their pertinence for the estimation of the stress in the reinforcement from the measured crack width is evaluated with satisfactory results for monotonic loading and for the maximum force in cyclic tests. [ABSTRACT FROM AUTHOR]

Based on an analysis of the literature on fiber‐reinforced concrete (FRC), especially the development and formation of various types of FRC combined with reactive powder concrete (RPC) in recent years, this paper systematically expounds the research progress, particularly the mechanical properties, of steel fiber RPC, basalt fiber RPC and hybrid fiber RPC. This paper concludes the improvement in the mechanical properties of RPC under common curing methods, elaborates on the influence of steel fiber on the compressive, tensile, and flexural strength of RPC, and outlines the principle of fiber enhancing the mechanical properties of RPC. Additionally, it discusses the research progress in basalt FRC, and further examines the impact of basalt fiber on the mechanical properties of RPC. Referring to the research on single fiber reinforced RPC, the mechanical properties of hybrid fiber RPC are analyzed and summarized; based on the characteristics of steel fiber and basalt fiber, research on steel‐basalt hybrid fiber RPC is proposed. [ABSTRACT FROM AUTHOR]

In this paper, a probabilistic methodology based on image analysis is proposed for earthquake‐induced loss estimation in rectangular reinforced concrete shear walls (RCSWs) in compliance with FEMA P‐58. The methodology is developed using a databank of 285 surface crack patterns gathered from the result of experimental research on 99 rectangular RCSWs with wide‐ranging structural and geometric characteristics. For the complexity extraction, three fractal geometry indices of the damaged specimens are taken into consideration. Fragility functions are generated to determine the probability of exceeding a FEMA P‐58 compliant damage state based on the various methods of repair for specific complexity indices. The fragility functions are obtained using four common probabilistic distributions including lognormal, Weibull, gamma, and beta. The fitness of the fragility curves is examined by two goodness‐of‐fit tests, namely the Kolmogorov–Smirnov test and Lilliefors test. Results show that the Weibull is the best‐fitting distribution for the majority of damage states and succolarity possesses the best results in goodness‐of‐fit tests among fractal geometry indices. Empirical loss indices are also derived in this paper aimed at optimizing the goodness‐of‐fits. Finally, the proposed procedure is utilized for a sample specimen from the databank at various damage levels. [ABSTRACT FROM AUTHOR]

A cement‐based material that meets the general goals of mechanical properties, workability, and durability as well as the ever‐increasing demands of environmental sustainability is produced by varying the type and quantity of individual constituents in high‐performance concrete (HPC) and ultrahigh‐performance concrete (UHPC). Expensive and time‐consuming laboratory experiments can be used to estimate the properties of concrete mixtures and elements. As an alternative, these attributes can be approximated by means of predictive models created through the application of artificial intelligence (AI) methodologies. AI approaches are among the most effective ways to solve engineering problems due to their capacity for pattern recognition and knowledge processing. Machine learning (ML) and deep learning (DL) are a subfield of AI that is gaining popularity across many scientific domains as a result of its many benefits over statistical and experimental models. These include, but are not limited to, better accuracy, faster performance, greater responsiveness in complex environments, and lower economic costs. In order to assess the critical features of the literature, a comprehensive review of ML and DL applications for HPC and UHPC was conducted in this study. This paper offers a thorough explanation of the fundamental terms and ideas of ML and DL algorithms that are frequently used to predict mechanical properties of HPC and UHPC. Engineers and researchers working with construction materials will find this paper useful in helping them choose accurate and appropriate methods for their needs. [ABSTRACT FROM AUTHOR]

It is common knowledge that increased temperatures have a negative impact on the axial load‐capacity and stiffness of reinforced concrete (RC) rectangular columns. This is something that is commonly acknowledged. For the purpose of restoring the axial capacity and stiffness of heat‐damaged RC columns, it is absolutely essential to carefully pick a suitable method for strengthening and repairing the columns. This research paper investigates the performance of various strengthening methods, such as the use of carbon fiber‐reinforced polymer (CFRP) jackets with near‐surface mounted (NSM) steel bars and a combination of welded wire mesh (WWM) and CFRP strengthening techniques, for the rehabilitation of RC rectangular columns that have been damaged due to exposure to high temperatures. Specifically, the paper focuses on the performance of these methods in relation to the rehabilitation of RC rectangular columns. There were three groups of tested RC rectangular columns: pre‐heated and unstrengthened, post‐heated and unstrengthened, and post‐heated and strengthened. Over a period of 3 h, 600°C was applied to the heated columns. Both a scheme utilizing a combination of unidirectional CFRP strips and NSM steel bars and another utilizing a combination of unidirectional CFRP strips and WWM were evaluated. Axial compression tests were performed on each column until failure occurred. The experimental test outcomes revealed that exposure to high elevated temperatures led to a decrease in the axial load‐carrying capacity of 38.6% and a decrease of 75.9% in initial stiffness, compared to unheated RC columns. Both strengthening schemes proved effective in restoring and surpassing the initial load‐carrying capacity of undamaged RC rectangular columns by an average of 35%. Notably, the combination of CFRP strips and WWM exhibited superior performance in restoring the initial stiffness of post‐heated RC rectangular columns, representing a novel finding. The strengthening scheme employing WWM and CFRP recovered 61.3% of the lost axial strength caused by high temperature, while the NSM/CFRP scheme restored 34.5% of the lost axial strength. In addition, the utilization of NSM in combination with CFRP strips as well as utilization of the WWM and CFRP systems leads to stiffness enhancement of 52.1% and 123.7%, respectively, when compared to post‐heated and unstrengthened RC columns. However, the study's findings have clearly shown that combination of WWM and CFRP strips is efficient in enhancing the strength of heated and unheated damage RC beams. [ABSTRACT FROM AUTHOR]

The objective of this paper is to present the methodology used to validate the threshold levels of durability indicators from data acquired from existing reinforced concrete structures that may present corrosion problems resulting from carbonation or chloride ingress. This study was conducted in the framework of the French National Project PERFDUB in close collaboration with the MODEVIE ANR project. Durability tests form the basis of a performance‐based approach for the durability of concrete structures, and in order to set the threshold level for each of these durability indicators, it is important to take into account the experience feedback that can be obtained from the actual behavior of existing structures. This paper presents the investigations carried out on eight reinforced concrete structures, all of them having an age well in excess of 50 years, and the main data gathered on some relevant durability and lifetime indicators. Based on all these data, predictive models of carbonation and chloride penetration are applied in order to validate the threshold levels to be adopted for the durability indicators, and several other conclusions are drawn. [ABSTRACT FROM AUTHOR]

Improvement of the bonding and interaction between concrete and steel is crucial to achieving an optimal reinforced concrete member. The proposed technique in this paper is using perforated steel plates (PSPs) to reinforce two‐way concrete slabs. In this method, ordinary steel bar reinforcements in the tension region of the concrete slabs were replaced by PSPs. Concrete slabs reinforced with PSPs enhance structural characteristics with respect to concrete slabs reinforced with ordinary reinforcement (OR) due to the higher lateral stiffness of PSPs, the better confinement of concrete within the holes of PSPs, the biaxial performance of the steel in the tension region, and the efficient load transmission mechanism between the steel and concrete. In this paper, a comprehensive experimental investigation was conducted on two‐way concrete slabs reinforced with PSPs and ordinary steel bars. The behavior of PSPs slabs was evaluated in comparison with OR slabs in terms of failure types, ductility, energy absorption, stiffness, ultimate load, cracking load, and force transmission mechanism. Findings revealed that the PSPs slabs have higher ductility, energy absorption, and ultimate strength compared to the OR slabs. [ABSTRACT FROM AUTHOR]

Bonded concrete overlays are widely used for strengthening and repair of concrete members. The aim of a concrete repair is to restore the load‐carrying capacity and stiffness of a concrete member, and to extend the service life of a structure. The bond between substrate and overlay is one of the main factors concerning the serviceability of a composite member consisting of concrete of different ages. This paper aims at better evaluating, through an extensive experimental program, the shear bond strength between existing concrete and a subsequently applied fiber reinforced overlay. The main purposes of this test program are to study the influence of the substrate strength and of the substrate surface roughness on the interface bond strength between a substrate and overlay concrete. A refinement of a novel bond test, proposed by some of the authors of this paper, is also implemented. Results indicate that there is an increase in the bond strength with an increase in the substrate compressive strength. On the other hand, the results suggest that, for the substrate strength classes investigated, the surface roughness does not influence the interface bond strength. [ABSTRACT FROM AUTHOR]

Fully embedded and spatially diffuse sensors are central to the advancement of civil and construction engineering. Indeed, they serve as an enabling technology necessary for addressing the current challenges associated with through‐life management and structural health monitoring of existing structures and infrastructures. The need to identify structural issues early on has driven the integration of such embedded sensing capabilities into construction materials, turning passive structures into proactive, self‐aware “entities,” commonly referred to as Smart Structures. The economic rationale behind this endeavor is underscored by the vital significance of continuous monitoring, which enables prompt anomaly assessment and thus mitigates the risks of potential structural failures. This is particularly relevant for road and rail infrastructures, as they represent a substantial and enduring investment for any nation. Given that a large majority of these large infrastructures are composed of concrete and reinforced concrete, both academics and construction companies are continuously researching micro‐ and nano‐engineered self‐sensing solutions specifically tailored for this building material. This comprehensive review paper reports the latest advances in the field of self‐sensing concrete as of 2024, with an emphasis on intrinsic self‐sensing concrete, that is, electrically conductive functional fillers. A critical analysis and a discussion of the findings are provided. Based on the perceived existing gaps and demands from the industry, the field's future perspectives are also briefly outlined. [ABSTRACT FROM AUTHOR]

This paper presents a numerical and experimental study aimed at the modeling and dynamic characterization of the reinforced concrete structure of the Palazzetto dello Sport in Rome, designed and by Pier Luigi Nervi with Annibale Vitellozzi, and built by Nervi & Bartoli contractors in 1956‐57. An experimental dynamic testing campaign has been performed to obtain the modal properties of the structure, identified using operational modal analysis (OMA). The axial symmetry of the Palazzetto's dome, expected to exist in an idealized perfect dome, has been observed to occur experimentally by noting that rotated modes possessed nearly identical frequencies, evidenced by closely spaced double peaks in the power spectral density. This observation recognizes the remarkable precision of Nervi's construction methodology. A numerical 3D model has been developed by relying on detailed information about the structure gathered from various sources, including archival documents, on‐site testing, and surveying. The model has been calibrated by means of modal updating based on the experimental measurements collected in this study. The reconstruction of the dome using laser‐scanning and aerophotogrammetry has revealed a slight asymmetry in its thickness distribution (and consequently its mass distribution) that, when incorporated in the numerical model, has been shown to contribute to the experimentally observed frequency split. It is expected that, by tracking these closely spaced frequencies on top of the typical variations of natural frequencies in a health monitoring approach, further insight might be gained into the detection of possible damages and/or degradation of the structure and its components. [ABSTRACT FROM AUTHOR]

Reinforced concrete (RC) structures are mainly designed to withstand both static and dynamic loads. However, due to the highly nonlinear behavior of RC structures subjected to extreme dynamic loads, these structures have a very complex damage behavior under dynamic impact loading. In fact, current existing methods for damage‐simulation and prediction are generally based on either empirical data, simplified mechanical approaches or complex numerical simulations mainly using the finite element method. In this regard, empirical and semi‐empirical models can be considered to calculate the load‐bearing capacity in a simplified way with only a few input parameters. Hence, using current experimental test data, this paper aims to analyze and assess existing empirical and semi‐analytical approaches that are established in standards and guidelines. Accordingly, a functional relationship in terms of an impact factor is found. Based on the obtained results, different approaches are also developed to describe the resistance to projectile penetration of RC structures as well as the force interaction between projectile and RC structures. [ABSTRACT FROM AUTHOR]

The study examines the early incorporation of reinforced concrete in the architecture of Historicism in Austria–Hungary. Spanning the late 19th to early 20th centuries, the research illuminates the period's stylistic pluralism and the transformative impact of reinforced concrete. The paper examines the integration of reinforced concrete into traditional forms, providing detailed case studies and architectural examples. It navigates through various aspects, including the evolution of reinforced concrete during the historicist period, its adoption in notable structures, and its documentation in contemporary literature. Case studies, such as the Lutheran Church in Battyánd (now Puconci, Slovenia), the Roman Catholic Church in Topolya (now Bačka Topola, Serbia), and the former Synagogue in Český Krumlov, Czechia, showcase the innovative ways reinforced concrete addressed structural challenges while adhering to historicist aesthetics. The research concludes by reflecting on the transformative role of reinforced concrete in challenging the conventions of Historicism, paving the way for modern architectural expressions. [ABSTRACT FROM AUTHOR]

The paper investigates the behavior of glass‐fiber reinforced polymer (GFRP) reinforced concrete columns with integrated steel spirals (hybrid reinforcement). Six concrete columns were tested under eccentric axial loading, resulting in failure due to bending. Columns with outer steel longitudinal bars experienced steel yielding at peak loads, while those with GFRP outer rebars failed due to concrete crushing. The results revealed that using GFRP as outer longitudinal bars led to peak loads 3–10% lower compared to columns with steel rebars. Inner confinement by steel spirals increased the load‐carrying capacity. Additionally, columns with inner tubular steel exhibited greater strength than those with steel spirals, indicating a slightly enhanced confinement effect. A finite element model was developed to analyze structural behavior, considering both material and geometric nonlinearity. The model's accuracy was validated by comparing predictions with test results. Parametric analysis from the nonlinear FE model showed that eccentricity significantly impacted column load‐carrying capacity. Increasing inner confinement area and the number of inner longitudinal bars improved structural stiffness and load‐carrying capacity. Furthermore, a simplified theoretical method was proposed. Comparison between experimental failure loads and theoretical predictions revealed differences within 20%, indicating satisfactory reliability of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents the experimental results of six full‐scale one‐way reinforced concrete slabs with variations in reinforcement detailing. Test specimens consisted of two reference concrete slabs reinforced fully with glass fiber reinforced polymer (GFRP) rebars or with steel rebars and four hybrid‐reinforced slabs. The variables included the arrangement of rebars, mechanical reinforcing ratio, and the ratio of steel rebar area to GFRP rebar area. The fabricated specimens were subjected to four‐point loading until failure in the strong floor laboratory. Experimental results indicated that hybrid reinforcement enhances stiffness compared to FRP reinforcement and provides a higher load‐bearing capacity than steel reinforcement. Also, it was observed that FRP bars placed as tensile reinforcement, similar in number and diameter size to steel bars placed as compressive reinforcement in a slab result in the highest ultimate capacity. Moreover, it was observed that while the mechanical reinforcing ratio contributes to the overall behavior of hybrid‐reinforced concrete slabs, the ratio of steel rebar area to GFRP rebar area is not considerably effective. Furthermore, image processing was employed to determine the exact crack widths of specimens after failure. Finally, finite element modeling results showed good agreement with the experimental results. [ABSTRACT FROM AUTHOR]

Alkali silica reaction (ASR) is an undesirable phenomenon that occurs between alkalis that usually originate from cement and certain types of siliceous aggregates in concrete. The result of this reaction is delayed expansion of hardened concrete in the presence of moisture, which may cause cracking and damage in an existing structure. The present paper investigates the general behavior and shear strength of pretensioned concrete bridge girders affected by ASR. Four identical pretensioned concrete AASHTO Type I girders were fabricated using reactive concrete and subjected to environmental conditioning at a relative humidity of 100% and a temperature of 45 degrees Celsius for up to 296 days to accelerate the development of ASR. During this period, ASR‐induced expansions, changes in surface strains of concrete, transfer lengths, and patterns of damage and cracking were monitored. Each specimen was subjected to shear‐critical loading until failure upon reaching the desired expansion level. The results showed that the existence of prestressing force played a significant role in limiting the ASR‐induced in‐plane expansion and cracking. Progress of ASR caused a reduction in the load corresponding to the first detected flexural crack but an increase by up to 14% in the load corresponding to the first diagonal cracking compared to the control specimen, likely due to the additional prestress caused by restrained ASR‐induced expansions. The ultimate shear strength of ASR‐affected girders was generally within 5% of the control specimens, and all specimens exceeded their nominal shear strengths according to AASHTO LRFD 2020 specifications. Until the unrestrained uniaxial expansion of 0.2%, no significant concerns were identified regarding the shear strength of the ASR‐affected pretensioned concrete specimens. [ABSTRACT FROM AUTHOR]

The shear wall system with cast‐in situ concrete infilled walls has been widely used in high‐rise buildings due to its significant advantages in construction. In this paper, quasi‐static tests were conducted on the shear walls with and without cast‐in situ concrete infilled walls to analyze their failure modes, load‐bearing capacity, stiffness, energy dissipation capacity, and ductility. A simplified model of the shear wall with cast‐in situ concrete infilled walls was proposed based on the fiber element model in OpenSees. The test results showed that the shear wall specimens with cast‐in situ concrete infilled walls exhibited full‐section compression or tension failure, and the cast‐in situ concrete infilled walls did not show obvious damage. Compared with the shear wall without infilled walls, the overall stiffness, load bearing capacity, and energy dissipation capacity of the shear wall specimens with cast‐in situ concrete infilled walls improved, indicating better seismic performance than those without infilled walls. Comparison between the hysteresis and skeleton curves derived from the tests and those simulated by the proposed simplified model revealed errors within 15% for stiffness, yield bearing capacity, and ultimate bearing capacity for shear walls with cast‐in situ concrete infill walls, affirming the effectiveness and accuracy of the model. [ABSTRACT FROM AUTHOR]

The mechanical behavior of cable pylon anchorage zone in a cable‐stayed bridge is complex due to high localized stresses. A strut‐and‐tie model (STM) has been introduced in this paper, which is recommended as an efficient way to analyze the disturbed region. However, predicting the internal forces in the tie members in the STM by integrating stresses was time‐consuming and inefficient. To address this issue, the principle of minimum strain energy was used to analyze the STM of the cable pylon anchorage zone. A simplified method was presented to assess the internal forces in the cable pylon anchorage zone. Moreover, an actual bridge (Cao'e River Bridge) was employed to be analyzed, and the prestressed steel strands in the bridge were obtained by the simplified method. A full‐scale test model of the bridge was fabricated to validate the accuracy of the simplified method. Furthermore, based on the simplified method, the effect of the thickness of front wall, the length of inner opening straight section, the thickness of side wall, the thickness of inner wall and the width of inner opening straight section on the internal force in the tie members in the STM was studied. The results show that the length of inner opening straight section has negligible effect on the internal forces in all tie members. Compared with the thickness of the side wall, the thickness of inner wall and the width of inner opening straight section have limited effect on the internal force of tie members. This study was expected to promote the design of cable pylon anchorage zone. [ABSTRACT FROM AUTHOR]

This paper aims at assessing the failure time of a 7‐story reinforced concrete (RC) frame in a post‐earthquake fire (PEF) event probabilistically. Cumulative distribution functions (CDF) of the studied frame's failure time in various seismic load intensities have been calculated and presented with the aid of Monte Carlo analysis. Seismic load intensity, failure time, and failure probability are three parameters that are correlated through probabilistic analysis. The effects of cracking, spalling, and residual deformations resulted from the seismic load are considered in the strength of structure against the fire load. Seismic load intensity, materials properties, gravity load, and geometry are considered as random variables and one probabilistic analysis has been carried out for each seismic load intensity. The results have illustrated that in low seismic load intensities, probabilistic values of failure time in a structure subjected to pure fire load are equal to the one exposed to PEF. With the increase of seismic load intensity, the effects of cracking, spalling, and residual deformations would lead to a decline in the strength of structural elements against PEF scenario. The failure time in 50% failure probability for Sa = 0.2 g, Sa = 1 g, and Sa = 2 g intensities has been calculated as 14,300, 12,200, and 5100 s, respectively. The analysis results have shown that in an unspecified seismic load intensity, the failure time of the 7‐story RC frame for the 50% occurrence probability is equal to 9750 s. [ABSTRACT FROM AUTHOR]

This paper presents experimental and numerical investigations on the behavior of eccentrically loaded lightweight aggregate concrete encased steel (LWACES) columns after exposing to elevated temperatures. Sixteen concrete encased steel (CES) columns were considered in the study, 12 of which were exposed to elevated temperature then eccentrically loaded up to failure at different eccentricity ratios. The effect of temperature on the load–displacement relationships, failure load, and failure modes of the concrete encased steel (CES) columns was monitored and evaluated. Experimental results have shown that as the temperature increases, the load bearing capacity of the CES columns decreased. It has also been showed that, at high temperature, the normal‐weight concrete encased steel (NWCES) columns experienced larger degradation of the load bearing capacity compared to that of LWACES columns. Also, this study presents a numerical simulation of the behavior of LWACES columns at elevated temperatures with eccentric compressive load. The numerical model was implemented in conducting parametric study to understand the effect of temperature distribution, concrete cover, eccentricity ratio, and high temperature levels on the behavior of the thermally exposed (CES) columns. Numerical results have revealed that, at temperature value of 500°C, the ultimate capacity of LWACES with eccentricity ratios of 0.75, and 1 has decreased by 17%, and 23%, respectively, compared to that of the column with eccentricity ratio of 0.5. [ABSTRACT FROM AUTHOR]

The joints between precast reinforced concrete pile segments in deep foundations are typically mechanically lockable. They include anchor bars embedded inside the ends of each segment, forming lap splices with the main bars. Because of their particular technology, these lap splices are somewhat different from traditional lap splices, as shown in the first part of this paper, where the impact of their specific characteristics on the tensile behavior of the joints is discussed. The experimental section presents the results of 19 tensile tests on these lap splices and compares them with established theoretical models. The roles of various parameters (lap length, type and amount of confining reinforcement, type of anchor bars, and concrete cover thickness) are investigated. One of the major findings indicates a significantly lower lap capacity when using plain‐bar spirals compared to closed‐ribbed stirrups. Additionally, at low stress levels, the models tend to be unconservative. Building on this insight, a modified model is proposed for lap splices provided with plain‐bar spirals. [ABSTRACT FROM AUTHOR]

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either explicitly in mechanical models or implicitly in empirical relationships. Furthermore, there are cases where the connection between various concrete elements explicitly depends on dowel action, as for example, in connections between precast elements or between two concrete parts cast at different times. On the other side, dowel action can have a negative impact on the fatigue resistance of reinforcing bars subjected to cyclic loading, because of the local stress concentrations near interfaces due to relative movements, either in sliding or in opening of cracks not perpendicular to the bar. For the assessment of the remaining capacity of existing structures, improved models of the behavior are needed, including realistic models of the behavior of concrete, steel and their interfaces. The aim of the present paper is to provide a contribution to a better understanding of dowel action by two test series. The first series focused on the behavior of the dowel: the concrete specimens with the embedded bars were placed in a custom‐made test setup and subjected to monotonic or low stress‐level cyclic actions with a longitudinal and a transversal crack opening component, up to developing the full plastic capacity of the dowel and rupture at the peak of catenary action. The measurement system included tracking the displacement field at the surface of the concrete and the strains in the dowel by optical fibers glued on its surface. The latter measurements allow to derive the internal forces in the reinforcing bar and deformed shape of the bar as well as the contact pressure between the bar and the surrounding concrete. The results show a strong dependency on the test variables: diameter of the bar, imposed crack kinematics and angle between the bar and the crack. The second test series looked more closely at the behavior of concrete underneath the bar, in the presence of a point load introduced at various locations into concrete through a reinforcing bar. A comparison of the test results with existing models shows a general good agreement and some aspects that deserve to be improved. [ABSTRACT FROM AUTHOR]

This paper describes the structural aspects of the Wieselburg Bridge collapse in Austria. The original design and reinforcing details for this integral concrete bridge are discussed. The collapse of the bridge is re‐constructed based on forensic documentation of the failure. The results of structural analysis carried out using material properties obtained after failure are compared to the shear capacity obtained from various models and from test results from literature. The results are used to explain the cause of failure of the integral bridge under dead load. [ABSTRACT FROM AUTHOR]

In this paper, a numerical critical shear crack model, in which the shear‐flexural coupling effect is considered and the full process of stress and strain is captured, is proposed to evaluate the post‐peak behavior of reinforced concrete (RC) and steel fiber reinforced concrete (SFRC) beams. The shape of critical shear crack is identified by combining the modified compression field theory considering the bridge effect of steel fibers and the section analysis method. Based on the shape of critical shear crack, the shear capacity of beam members is provided by the shear tension zone and the shear compression zone. The shear capacity of the shear tension zone is calculated by the modified compression field theory and that of the shear compression zone is determined by multiaxial strength criterion of concrete. The vertical displacements caused by the flexure deformation and shear deformation are deduced by the moment area method and integration of shear strain. To verify the proposed numerical approach, a test database of 486 RC beams and 313 SFRC beams was established to predict the shear strength, and the force‐displacement relationships of twelve beam members are used to validate the feasibility for full process analysis. The stochastic analysis of beams with different failure modes is conducted via GF‐discrepancy‐based point selection method and probability density evolution method. The limitation between different failure modes is defined according to the degradation percent of shear capacity and it is taken as threshold value of failure domain, and the failure probability analysis indicates that the designed flexure beam member suffered severe degradation of shear capacity, resulting in a significant decline in safety probability. [ABSTRACT FROM AUTHOR]

This paper presents an experimental investigation of the use of composite polymer mortar (CPM) and steel strands wire mesh (SSWM) to strengthen reinforced concrete (RC) beams in shear. In order to maximize the shear resistance of the steel strands, a new type of anchor device called wedge‐shaped steel plate hoops (WSSPHs) was developed. And the study aimed to examine the effect of shear‐to‐span ratio and prestressing level on the mechanical properties of the beams. A total of nine beams were constructed and tested under four‐point bending monotonic load, comprising three control beams and six strengthened beams. The study analyzed the damage modes, load‐deflection curves, strength, stiffness, and ductility of the beams. The test results indicated that (1) the mechanical properties of the strengthened beams were improved, with the shear capacity improving by 38.47%–71.37% after strengthening. (2) It was observed that SSWM could be utilized more effectively in high shear‐to‐span ratio beams among the strengthened beams with the same prestressing level. (3) Additionally, the larger prestressing level was found to change the design damage mode of the test beams, with RB‐2.5‐0.5 failing in bending. Finally, a model was proposed to predict the shear capacity of the test beams based on the specification GB 50011‐2010. The model considered the effect of the initial prestressing of the steel strands. [ABSTRACT FROM AUTHOR]

Alkali‐aggregate reaction (AAR) is a detrimental reaction between alkalis originating from cement and aggregates that contain reactive minerals. This reaction produces an expansive gel in hardened concrete that may cause internal stresses and cracking, after which it would be critical to evaluate the safety of the AAR‐affected structure. This paper presents a calculation framework primarily using the finite element method to simulate the structural behavior of reinforced concrete members affected by AAR. Numerical subroutines are used to calculate the anisotropic distribution of AAR‐induced expansions at each integration point, considering the stress field at each time step, whereas changes in the properties of concrete due to the progression of AAR are also considered. The modeling approach is successfully validated based on experimental data from several studies on AAR‐affected members that were reinforced in 1, 2, and 3 orthogonal directions in terms of load–deflection behavior and damage patterns. The mechanical properties of concrete were found to negligibly affect the distribution of AAR expansions. A better correlation was observed with experimental data if compressive and tensile strengths of concrete are assumed unchanged and only the modulus of elasticity of concrete is reduced as a function of AAR‐induced expansion. [ABSTRACT FROM AUTHOR]

The main objective of this paper is to use the data‐driven approach to predict and evaluate the mechanical properties of concrete made with recycled concrete aggregate (RCA), including compressive strength and elastic modulus. Using 358 data samples, including 10 input variables, 10 popular machine learning (ML) algorithms are introduced to select the best ML performance model for predicting RCA concrete's compressive strength and elastic modulus. Gradient Boosting and Categorial Boosting have the best performance in predicting the compressive strength of RCA concrete, with R2 = 0.9112, RMSE = 5.3464 MPa, MAE = 4.0845 MPa, and R2 = 0.9175, RMSE = 5.1520 MPa, MAE = 3.7567 MPa, respectively. Light Gradient Boosting and Categorial Boosting have the best performance in predicting the elastic modulus of RCA concrete, with R2 = 0.8775, RMSE = 2.3560 GPa, MAE = 1.8330 GPa, and R2 = 0.9300, RMSE = 2.3560 MPa, MAE = 1.2589 MPa, respectively. Based on the Shapley Additive Explanation analysis, the influence of main factors on compressive strength and elastic modulus of RCA concrete values has been analyzed qualitatively and quantitatively. RCA replacement level and cement/sand ratio slightly affect compressive strength but have a dominant influence on the elastic modulus of RCA concrete. [ABSTRACT FROM AUTHOR]

This paper presents an experimental shear test performed to investigate the web‐shear capacity of composite hollow‐core slabs (HCS) with cast‐in‐place (CIP) concrete. Five HCS specimens are fabricated, and the presence of a topping slab and number of cores strengthened by core‐filling concrete are set as key test variables. The shear force–displacement responses of the specimens, patterns of cracks occurring in the HCS and filled cores, strain behavior of stirrups, and composite action between the HCS and CIP concrete are measured and analyzed comprehensively. In addition, the web‐shear capacity of the composite HCS with CIP concrete is calculated based on elasticity theory and the transformed area method, in which the residual stress ratio factor is introduced to reflect the shear contribution of the core‐filling concrete after its shear cracking. Moreover, a practical equation is proposed to allow structural engineers to easily perform the shear‐strengthening design of HCS via the core‐filling method. The detailed model and the simplified equation accurately evaluate the web‐shear capacities of the HCS specimens. [ABSTRACT FROM AUTHOR]

The bond behavior between reinforcement and concrete has a significant influence on the load‐bearing behavior and serviceability of the composite material. This paper focuses on the characterization of the bond behavior between fine‐grained concrete and mineral‐impregnated carbon‐fiber reinforcement. In this study, the influence of different bond lengths on local bond behavior was experimentally investigated. To predict the bond stress along the bond length, an analytical bond stress‐slip model was specified, and its model parameters were determined based on the experimental tests using an iterative approximation approach. Based on the defined bond stress‐slip model, a numerical bond model was developed and adjusted for the first time. A three‐dimensional (3D) finite element analysis (FEA) allows the simulation of the local bond stress along the bond length. Finally, the results of the 3D FEA were compared with the results of the experimental investigations to validate the developed numerical model. [ABSTRACT FROM AUTHOR]

A growing body of research has shown that reversed cyclic shear loading of reinforced concrete (RC) causes effects that are not accounted for in monotonic behavioral models. Notable among these effects are a reduction in shear strength and significant plastic offsets. This paper presents the General Crack Component Model, a rational, mechanics‐based model that explicitly considers the constitutive behavior of cracks in RC. Cracked RC is treated as a series–parallel system of bonded and unbonded regions, where the crack interfaces have both crack closing hysteresis and a kinematic contact constraint. Validation was performed using data from monotonic and reversed cyclic experiments on panel elements, and has shown that this analytical model is able to accurately capture the salient features of reversed cyclic shear behavior. [ABSTRACT FROM AUTHOR]

This paper investigates the behaviors of different types of prestressed concrete beams utilizing fully encased cold‐ or hot‐formed steel joists. Twelve types divided into two sets of composite beams are assessed. Set 1 is composed of six beams utilizing cold‐formed steel (CFS) joists distinguished by the cross‐sectional steel‐to‐concrete ratios of 1%, 2%, and 3%, and the presence or absence of web openings. Set 2 has the similar composition but utilizes hot‐formed steel joists. Four‐point and three‐point bending tests were conducted at the mid‐span of the composite concrete beams. Key properties, such as strength, stiffness, flexural load capacity, ductility, energy absorption capacity, and failure modes, were used in the analysis. It was found that the specimens with CFS I‐beam joists provided better performance compared to those with hot‐formed steel joists. Also, the existence of web openings in the encased CFS beams enhances the ductility and energy absorption of the composite concrete beams. [ABSTRACT FROM AUTHOR]

To enhance the mechanical and constructional performance of the ultra‐high performance concrete (UHPC) beams, the steel plate placed at the bottom surface of the UHPC beam is utilized to replace the ordinary steel rebars. In this paper, four 3.2 m UHPC T‐shaped beams with different reinforcement patterns of ordinary steel rebars and external steel plate were fabricated and comparatively tested under flexure loading. Their damage patterns, load versus deflection behavior, flexural capacity, load versus strain behavior, moment versus curvature behavior, stiffness, and crack development were investigated. The flexural experiments indicated that the external steel plate, positioned at the bottom surface of the UHPC members, could resolve the difficulty of installing ordinary steel rebars in slender UHPC components and improve its constructional performance. Compared with the inside steel rebar reinforcement, the employment of the steel plate at the bottom surface of the UHPC beam can effectively increase the distance from the neutral axis to the tensile reinforcement at the serviceability and ultimate states, thereby improving its flexural capacity and stiffness. Additionally, the configuration of the external steel plate was beneficial to reduce the tensile stress level of the tensile reinforcement and limit the opening of UHPC crack width, and thus their crack resistance can be effectively enhanced. Moreover, increasing the thickness of the steel plate or rebar ratio can also significantly improve the flexural capacity, stiffness, and cracking resistance of UHPC beams. [ABSTRACT FROM AUTHOR]

The paper investigates the effect of high temperature exposure on the performance of concrete confined through textile/fabric‐reinforced composites. Small‐scale cylindrical specimens (150 × 300 mm) were confined using two types of carbon fibers (dry and epoxy‐resin coated). For the sake of comparison, two confining layers were applied to all specimens. After curing, cylinders were exposed to four ranges of increasing temperatures—being 20°C (ambient), 80°C, 100°C, and 250°C and, after cooling down, were tested under compressive cyclic loading. The experimental results show that thermal stress significantly influences the confinement effectiveness of textile‐reinforced composites. Exposure to high temperatures reduces the ultimate confined strength and significantly influences the overall axial stress–strain behavior. [ABSTRACT FROM AUTHOR]

This paper describes the 3rd Blind Simulation Competition (BSC) organized by the fib WP 2.4.1 which aims to assess the predictive performance of models based on the finite element method (FEM) for analysis and design of fiber reinforced concrete (FRC) structures submitted to loading and support conditions that promote punching failure mode. Fiber reinforcement is used in an attempt to eliminate conventional punching reinforcement and provide technical and economic advantages. The two tested real‐size prototypes represent a column‐slab interior region of an elevated steel‐fiber reinforced concrete (E‐SFRC) slab where anti‐progressive collapse reinforcement is disposed in the alignment of columns/piles. Despite a punching failure surface being formed in both experimentally tested prototypes at the rupture stage, fiber reinforcement was able to mobilize the yield capacity of the conventional flexural reinforcement, providing high deformation capacity, and ductility to the prototypes. The average post‐peak load‐carrying capacity of the tested prototypes at a deflection seven times higher than the deflection at yield initiation of the conventional reinforcement was still 90% of the average peak load. Regarding the BSC, a total of 26 proposals were received and involved 94 participants from 29 institutions and 17 countries, with 53.9% using smeared crack models (SCMs), 30.8% a concrete damage plasticity (CDP) model, 3.8% discrete crack models (DCMs) and 11.5% considered as “other models.” From these simulations it was verified, in average terms, that SCM assured the best predictive performance apart from the average strain in the SFRC and the maximum crack width which were better predicted by DCM. More accurate predictions were obtained by using in‐house software than by adopting commercial software. [ABSTRACT FROM AUTHOR]

During the cantilever casting process of reinforced concrete arch bridges with cantilever cast‐in‐situ method, it is difficult to select representative training samples for reliability analysis due to its complex structural system. Many random variables and large computational sample size, this paper proposes to solve the reliability indexes based on the combination of the improved sparrow search algorithm (LGSSA) and the support vector regression (SVR) method. Firstly, random variables are selected according to the actual situation of the bridge structure. Then representative training samples are designed to be substituted into the finite element model through the homogeneous method. The resultant data samples are used to fit the functional function by the support vector regression. Then combined with the penalized function method to transform the nonlinear optimization into the problem of solving the extreme value of the function. Based on the improved SSA to solve the extreme value of the final function. Finally the reliability index of the structure is obtained. With the background of reinforced concrete arch bridge of 200 m, the method is used to analyze the reliability of its buckling cable stress, arch stress, buckling tower deviation and structural system reliability during the cantilever casting process. The results show that the overall structural reliability of the arch ring during cantilever casting is 3.502–3.608. The indexes of buckling cable stress reliability are 3.806–6.784. The indexes of arch ring stress reliability are 4.379–7.562, and the indexes of buckling tower deflection reliability are 3.608–8.123. [ABSTRACT FROM AUTHOR]

The use of UHPC enables reducing the height of composite slabs, which may decrease the punching shear capacity. This paper investigates the punching shear behavior of steel‐normal concrete‐UHPC composite slabs with experiments and theoretical analyses. Results indicated that a 50 mm UHPC layer makes the nominal punching shear strength increase by 24.91%. Utilizing UHPC and increasing loading area can effectively enhance the punching shear capacity. Besides, theoretical punching shear model proposed based on rigid‐plastic theory can reliably predict the punching shear capacity of composite slabs. The punching shear angle derived from strength theory closely matches the experimental values. [ABSTRACT FROM AUTHOR]

The paper presents an experimental study for the evaluation of the flexural response and failure mode of a prestressed concrete (PC) beam subjected to simultaneous sustained loads and corrosion. The obtained results are judged and discussed also through a comparison with the experimental outcomes on a reference sound PC beam, and a companion specimen subjected to artificial corrosion first, and then tested in bending. The three specimens are characterized by a 200 × 300 mm rectangular cross section, a total length of 3700 mm, and a clear span of 2700 mm. The value of the sustained load, applied with a simultaneous accelerated corrosion process of the strands, was chosen, based on the result of the uncorroded reference beam, to achieve a scenario that can occur in a real structure in situ. The flexural response of the tested element was monitored over a period of 70 days, up to failure, and showed to be highly dependent on the localization of the corrosion phenomena affecting the strands, especially when coinciding with the maximum bending moment position. The obtained results are finally compared with the ones obtained on a PC beam with the same geometry and material properties, first subjected to corrosion and then tested in bending. The differences in corrosion morphology and location and in the failure mode of the strand confirm the importance of accounting for the combined effect of reinforcement corrosion and loading when assessing the structural performance of PC beams. [ABSTRACT FROM AUTHOR]

This paper investigates the effects of pozzolanic substitutions for ordinary Portland cement (OPC) with silica fume (SF) and metakaolin (MK) on the mechanical and toughness performances of steel fiber reinforced concrete (SFRC). Initially, a reference concrete mix with a water‐to‐binder ratio of 0.4 is blended with different volume fractions of steel fibers with varying geometry: crimped steel (CS) and straight steel (SS), both individually and in combination, to examine their mechanical properties. In the subsequent phase, the study investigates the impact of combining macro‐ and microsteel fibers on flexural toughness, to determine potential synergy for suitable combinations. Also, the possible influence of pozzolans in the variation of flexural toughness of hybrid steel fiber reinforced concrete (Hy‐SFRC) was evaluated. Hybridization of steel fibers was found effective in improving the workability of the concrete mix up to 11%. SFRC mixes containing pozzolans exhibited a significant enhancement in compressive strength, modulus of rupture, and modulus of elasticity compared to non‐pozzolanic SFRC. The hybrid combination of CS 1.5% and SS 0.5% was considered the best in terms of mechanical properties. Additionally, the results of synergy assessment showed that hybridization of steel fibers in the pozzolanic concrete mix was particularly effective in the post‐cracking stages with a positive 14% compared to a negative 8% in the pre‐cracking stage. The pozzolanic addition improved the flexural toughness of Hy‐SFRC to about 10%–20%. Blending of SF and MK in Hy‐SFRC was found effective in enhancing the toughness mechanism of concrete compared to Hy‐SFRC mixes containing binary SF and MK, indicating a stronger bond between the fibers and the matrix resulting from the pore refinement and hydration products developed at the interface. Hy‐SFRC containing a ternary pozzolanic mix of SF 10% and MK 10% gave the best results in flexural toughness, and the corresponding synergy values were found to be the maximum. The results were consistent with the morphology analysis, which revealed an increase in hydration products at the interface between the aggregate and concrete matrix, as well as between the steel fiber and concrete matrix, due to the ternary blending of SF and MK. [ABSTRACT FROM AUTHOR]

In this paper, seven half‐scale specimens are used to investigate the effects of the beam–column width ratio, concrete strength, and axial load on the seismic performance of wide exterior beam–column joints. The test results show that all the specimens undergo bending damage at the beam end. The concrete damage in the core column is not significant, meeting the seismic requirements of strong column–weak beams and strong joint–weak members. For specimens with small beam widths, the increase in axial load can effectively reduce the damage to the concrete in the outer joint and increase the strength of the specimen. Increasing the beam width and concrete strength reduces the ductility of the specimen while increasing the strength of the specimen. The bonding performance of the longitudinal bars anchored outside the core column is poor, as bond–slip with the concrete is observed during the test. In addition, compared with ACI 318‐19, GB 50011‐2010 is more conservative for calculating the shear strength of exterior wide beam–column joints. Finally, a corresponding finite element model is established by MSC Marc and verified based on the experimental results. [ABSTRACT FROM AUTHOR]

This paper proposes a new design code formulation for calculating crack widths for regular and more special reinforced concrete (RC) members. The more comprehensive Modified Tension Chord Model (MTCM) has been simplified (SMTCM) to facilitate an alternative method for calculating crack widths to Eurocode 2 and fib Model Codes. The model is based on mechanical principles without empirical modifications and is benchmarked against a previously published experimental crack width database. The SMTCM predicts crack widths quite as accurately as the MTCM and provides a broader range of applicability, such as for large covers and RC ties having arbitrary rebar configurations and thus a better crack width model than the current design codes for RC ties. In addition, there are no openings for ambiguous interpretations of the calculations, which can increase the risk of obtaining two different crack widths from two different designers. To further justify the SMTCM code formulation and concept, several RC ties with experimental crack width profiles were used and discussed. The results show a considerable difference between the crack width profile at the surface and at the reinforcement location, depending on the concrete cover and rebar size. These observations are interesting regarding durability design and requirements and show that the approach using a maximum design crack width at a specific surface as a decisive parameter should be further investigated, especially for large concrete covers. [ABSTRACT FROM AUTHOR]

This paper investigated the blast behavior of a low‐rise composite steel structure of three stories subjected to internal and external explosions for the same explosive charge of 250 kg TNT. A comparison of three various blast scenarios is aimed at better understanding how blast waves propagate in confined risk zones and their damage effects on far and exposed elements to an explosive charge. Evaluation of the damage level and the overall response of the proposed numerical model is done by estimating the adequacy of structural members subjected to blast loading using general limits in attempting to check the structure's strength and regularity. The analysis was based on load combinations and damage criteria according to the Unified Facilities Criteria which are general design approaches suitable for civil design applications in forecasting blast loads and structural system responses. The overall behavior of this structure was simulated based on a dynamic analysis by the direct simulation approach, which was chosen for modeling blast loads using the Friedlander blast load equation, and the simpler, less expensive, more accurate, and realistic A.T.‐BLAST model to deduce the simplified blast‐wave overpressure profile. The material nonlinearity at a high strain rate using the Johnson‐Cook strength and concrete plasticity damage model is studied dynamically using ABAQUS finite element code to simulate the explicit dynamic nonlinear analysis. The overall response of the proposed numerical model was evaluated by estimating the adequacy of structural members, considering the blast load as the initial cause of failure, such as axial plastic strain, internal forces limits, maximum deformation, support rotation, demand‐capacity‐ratio (DCRshear/moment), drift index and material damage model. The position of the explosive charge played an important role in determining the rate at which the structural element begins to plastic strains, displacements, moments, or rotations beyond the limits, and then key elements should be considered in structural design against progressive collapse. Results showed that steel members exhibit early indicators of failure, such as buckling necking, shear tearing, or plastic hinges, whereas concrete slabs break up immediately due to brittleness. DCRmoment values successfully showed the columns in which the first plastic joint can occur, whereas DCRshear values signaled the onset of shear failure at connections. Besides, plastic hinges played an important role in dissipating energy and preventing total structural collapse via the Strong Column‐Weak Beam design concept, which appears repeatedly in this study. The structure is a well‐designed and ductile building capable of supporting higher loads and is considered to be repairable and intact. [ABSTRACT FROM AUTHOR]

Although plain round or square section reinforcement is no longer used in new construction, there are many older structures still in service built with such bars. In recognition of the need for guidance on the assessment of load‐carrying capacity of structures reinforced with such bars, design codes are now introducing or re‐introducing provisions to assess the capacity of laps and anchorages of such reinforcement. The authors have contributed to the introduction of design rules in the fib Model Code 2020. This paper describes the derivation of these provisions. Starting from the form of expression proposed earlier by the authors, the data from which these proposals are derived is specified and modifications in interpretation preparatory to a statistical analysis are outlined. A rigorous multivariate statistical procedure is then employed firstly to determine a mean strength expression for the capacity of anchorages and laps which is then validated against test data. Further statistical analysis is subsequently used to determine a design expression using the approach outlined in EN 1990, taking appropriate account scatter in test data. Finally, some comparisons are presented between the assessment expressions proposed and design provisions that were in place when these types of bars were in common use. Areas where earlier design provisions may be non‐conservative are identified. [ABSTRACT FROM AUTHOR]

This paper presented the experimental results of the strength capacity of studs embedded centrally in concrete with red mud synthetic coarse aggregates, with the variation of the handcrafted headed stud thickness (3.17, 4.76, 6.35, and 7.9 mm) and no shank bond influence with concrete. The results regarding the compressive strength of concrete showed considerable strength gain with synthetic coarse aggregate, ranging from 27.00 to 43.50 MPa, while in concrete with natural coarse aggregate, the variation was 27.00 to 36.50 MPa. Also, it was observed that the cracking in the concrete matrix of the synthetic coarse aggregate occurred in the aggregate instead of the transition zone, as occurred with the natural coarse aggregate concrete. However, the solid morphological formation of synthetic coarse aggregate provided excellent chemical adhesion to the headed stud, providing a hardening failure behavior after reaching the yield strength value of the steel bar with higher displacements. This can enable the optimized consumption of materials in the dosage of low‐strength structural concrete and the anchoring application of studs with smaller‐headed thicknesses, up to 8% of head diameter, generating economy and sustainability. [ABSTRACT FROM AUTHOR]

This paper presents a state‐of‐art regarding the punching of flat slabs made with coarse recycled concrete aggregate concrete (CRCAC). Punching shear is a phenomenon that occurs in reinforced concrete slabs when concentrated loads are applied near a column or other support. It refers to the failure mechanism where the concrete reaches shear failure at a critical section around the column. CRCAC is a structural material that conforms with circular economy concepts, but its design for punching using current formulae may be unsafe due to the lower strength of the concrete that can be caused by the shape or the surface cleanness of the recycled aggregates when compared with the natural ones. The results highlight the need for further research on this area, since the available experimental results are few and mainly from tests with thin slab specimens. Since the punching phenomenon is dependent on the scale effect, it is mandatory to have more results for slabs with representative thickness. The applicability of the models for punching resistance in EC2, ACI318‐19, and the upcoming second generation of EC2 was also investigated. These codes can produce safe estimates for CRCAC slabs. However, it was found that the second generation of EC2 is less conservative than the other models. [ABSTRACT FROM AUTHOR]