Search

The global pandemic caused by the SARS-CoV-2 virus has underscored the need for rapid, simple, scalable, and high-throughput multiplex diagnostics in non-laboratory settings. Here we demonstrate a multiplex reverse-transcription loop-mediated isothermal amplification (RT-LAMP) coupled with a gold nanoparticle-based lateral flow immunoassay (LFIA) capable of detecting up to three unique viral gene targets in 15 min. RT-LAMP primers associated with three separate gene targets from the SARS-CoV-2 virus (Orf1ab, Envelope, and Nucleocapsid) were added to a one-pot mix. A colorimetric change from red to yellow occurs in the presence of a positive sample. Positive samples are run through a LFIA to achieve specificity on a multiplex three-test line paper assay. Positive results are indicated by a characteristic crimson line. The device is almost fully automated and is deployable in any community setting with a power source.Microfluidic paper-based analytical devices (μPADs) are foundational devices for point-of-care testing yet suffer from limitations in regard to their sensitivity and capability in handling complex assays. Here, we demonstrate an airflow-based, evaporative method that is capable of manipulating fluid flows within paper membranes to offer new functionalities for multistep delivery of reagents and improve the sensitivity of μPADs by 100–1000 times. This method applies an air-jet to a pre-wetted membrane, generating an evaporative gradient such that any solutes become enriched underneath the air-jet spot. By controlling the lateral position of this spot, the solutes in the paper strip are enriched and follow the air jet trajectory, driving the reactions and enhancing visualization for colorimetric readout in multistep assays. The technique has been successfully applied to drive the sequential delivery in multistep immunoassays as well as improve sensitivity for colorimetric detection assays for nucleic acids and proteins via loop-mediated isothermal amplification (LAMP) and ELISA. For colorimetric LAMP detection of the COVID-19 genome, enrichment of the solution on paper could enhance the contrast of the dye to more clearly distinguish between the positive and negative results to achieve a sensitivity of 3 copies of SARS-Cov-2 RNAs. For ELISA, enrichment of the oxidized TMB substrate yielded a sensitivity increase of two-to-three orders of magnitude when compared to non-enriched samples – having a limit of detection of around 200 fM for IgG. Therefore, this enrichment method represents a simple process that can be easily integrated into existing detection assays for controlling fluid flows and improving detection of biomarkers on paper. LNPs, with their lipid bilayer structure, protect fragile mRNA, extending circulation and improving cellular uptake. They can be engineered for tissue targeting and controlled release. Mouse models, due to their genetic similarity to humans, are vital for studying LNPs' biodistribution, pharmacokinetics, and therapeutic impact, as well as assessing immune responses. In this thesis, two PDMS microfluidic devices were developed for mRNA encapsulated LNPs, optimizing parameters like size, encapsulation efficiency, and zeta potential. Intraperitoneal and intravenous injections in mouse models quantitatively assessed LNP efficacy and performance.A groundbreaking high-voltage cold plasma device, paired with advanced cooling, revolutionizing biotechnology. This device enables precise detachment of adherent cells, a milestone in tissue engineering and regenerative medicine. Moreover, it enhances protein binding in ELISA assays, promising higher accuracy in diagnostics, biopharmaceuticals, and life sciences research by manipulating protein-surface interactions. This innovation redefines biotech tools, with far-reaching implications.

The flexibility and insulating nature of polymeric dielectric materials are widely used in robotic and wearable electronic devices like electrical insulation, capacitive sensors, and electromechanical actuators. When combined with a phase transition-induced shape memory property, the resultant bistable electroactive polymer (BSEP) opens up new applications due to the rigid-to-rigid actuation of BSEP tremendously reducing the energy consumption for device operation while providing desirable strength for external loads. This dissertation focuses on investigating insulating, electroactive, and phase transition properties of BSEP, and adapting each aspect of the properties in the pursuit of innovative devices, such as rewritable photonic paper, smart windows with whole solar spectrum modulation, and wearable pressure sensors. An ink-free rewritable photonic paper has been invented through the interdisciplinary combination of photonic crystals, shape memory and electroactive properties of BSEP. The rewritable paper consists of a ferroferric oxide-carbon (Fe3O4@C) core–shell nanoparticle (NP)-based photonic crystal embedded in a BSEP. The nanocomposite can be repeatedly triggered to change into different shapes and colors due to the z-directional deformation that is induced by an electric field. The actuated shape and color can be maintained for a long term without energy input, and the stored images can then be rewritten over 500 times without noticeable degradation. Low energy consumption and simple erasing/rewriting are features that match the benefits of conventional paper as a zero-energy and long term data storage medium, but provide the additional advantage of rewritability. With pixelated electrode arrays, user-defined information can be actuated and erased at will which has been demonstrated through a seven-segment numerical display. A smart window with wide-band light modulation is designed solely based on the phase transition property of BSEP. One component of BSEP can be switched between semicrystalline and amorphous states through cooling below or heating above its melting temperature, leading to a reversible opaque-to-transparent transition. The opacity switching property of BSEP was further improved by mixing a more hydrophilic component to induce micro-scale phase separation, which is responsible for the whole solar spectrum light modulation due to Mie scattering. The resultant smart window achieves both high solar transmittance modulation of 70.2% and high luminous transmittance modulation of 80.4% which rivals the best reported smart windows and commercial privacy glasses with the highest privacy levels. This flexible smart window can also be mounted on curved surfaces for the need of windows with arbitrary shapes. This work is the first one to report an all-solid thermochromic smart window film without the inclusion of any metal/metal oxides or liquid crystals to enable a large light modulation over the whole solar spectrum.A flexible fiber-based pressure sensor is realized by applying a dielectric layer on the outside of a TEMPO-oxidized bacterial cellulose (TOBC)/silver nanowire (AgNW) conducting fiber. The pressure sensor can detect pressures up to 134 MPa with sensitivity of 101 � 10-4 kPa-1 due to its hierarchical structure and high conductivity. The porous structure of TOBC/AgNW helps increase the thickness deformation of the sensor with applied pressure, improving the sensing ability. Small pressures of human pulse and voice vibration can be detected with this sensitive pressure sensor. A machine learning classification model was implemented to recognize human’s speech where the prediction accuracy on a test dataset is > 90%. The ultrathin fibrous sensor (53 �m) is capable of high-resolution detection, and suitable as a comfortable and fashionable thread substitute for real wearable devices.The combined properties of BSEP with the proof-of-concept developments of rewritable paper, smart windows and wearable sensors demonstrate its potential for real-world applications. And an outlook for future research and suggested improvements for commercialization are discussed in the conclusion.

This paper investigates the influence of thermal pretreatment on kinetic parameters based on four kinetic models: Modified Gompertz, transference and logistic functions and first order equation. The kinetic modeling was applied on experimental results of previous study on producing methane from anaerobic digestion of Recycled Pulp and Paper Sludge (RPPS) under mesophilic conditions. We observed that the thermal pretreatment improve considerably improved the kinetic parameters mainly the methane production rate and the lag phase. Indeed, it can be noted that methane production rate μ increases significantly from a value of 4.72 to 16.27 Nml/h using logistic function for 1 g VS/L added load. Then the lag phase parameter λ has dramatically decreased from 5.46 to 1.04 h using logistic function for 1,5g VS/L added load. This means that the thermal pretreatment of RPPS accelerates the methane production process and saves time.

Alstonia boonei, an abundant lesser utilized species within the West African Subregion, was evaluated as an alternative raw material for pulp and paper production. The basic density (BD), fibre characteristics [fibre length (FL), fibre diameter (FD), lumen diameter (LD) and wall thickness (WT)], derived anatomical indices [Flexibility Ratio (FR), Slenderness Ratio (SR), Rigidity Coefficient (RC), Luce’s Shape Factor (LSF), Solids Factor (SF) and Runkel Ratio (RR)] and chemical composition (lignin, holocellulose, 1% NaOH solubility and ash contents) of A. boonei were studied to evaluate variation along the trunk (base, middle and top portions) and ascertain its suitability for pulp and paper production. Significant variations were observed in the density and fibre characteristics along the trunk of the tree. Although the FD was large, the observed adequate FL, thin-wall and large LD implied easy beating of fibres and manufacture of dense, smooth and strong papers. The favourable SF, RR, FR, RC, and LSF values obtained for the fibres would produce papers with suitable burst and tearing strengths and folding endurance. Chemically the lower lignin (< 30%), ash and 1% NaOH solubility and the high holocellulose contents of A. boonei, will generate a higher pulp yield. A. boonei although a low-density species, will be desirable for pulp and paper production.

The rapid economic growth and environmental concerns have led to high demands on paper and paper-based products in terms of variety, quantity, quality, and specialty. Enhancement and functionalization with additives are constantly required. Moving away from traditional petroleum-based additives, researchers have attempted to use “green” nanoadditives by introducing renewable environmentally friendly nanocellulose. This article studies the functions of nanocellulose as bio-additives (enhancer, retention and filtration reagent, and coating aid) in paper and paper products, and overviews the research development of nanocellulose-based additives and their applications in the paper industry for both efficient production and paper functionalization. The review shows that (1) a variety of nanocellulose-based bioadditives have been reported for various applications in paper and paper-based products, while commercially viable developments are to be advanced; (2) nanocellulose was mostly formulated with other polymer and particles as additives to achieve their synergistic effects; (3) major interests have concentrated on the nanocellulose in the specialty papers as representing more value added products and in the efficient utilization of recycled fibers, which remains most attractive and promising for future development. This report shall provide most useful database information for researchers and industries for paper recycling and enhancement, and paper-based products innovation and application.

The pulp and paper industry is highly energy-intensive. In mills that use chemical pulping, roughly half of the higher heating value of the cellulosic material used to manufacture the product typically is incinerated to generate steam and electricity that is needed to run the processes. Additional energy, much of it non-renewable, needs to be purchased. This review considers publications describing steps that pulp and paper facilities can take to operate more efficiently. Savings can be achieved, for instance, by minimizing unnecessary losses in exergy, which can be defined as the energy content relative to a standard ambient condition. Throughout the long series of unit operations comprising the conversion of wood material to sheets of paper, there are large opportunities to more closely approach a hypothetical ideal performance by following established best-practices.

We present how harmful different wood extractives carried over to paper mill with unbleached softwood Kraft pulp are for the strength of packaging papers and boards. The investigations were done by simulating industrial papermaking conditions in laboratory-scale trials for handsheet production. It was found that fatty acids are the most relevant compounds in the carryover pitch extractives (CPEs), as they readily interfere in fiber–fiber bonding strength, control the properties of CPE micelles, and are furthermore the most abundant compounds. Addition of cationic starch improved strength and evened out the strength differences of handsheets with different CPE compounds. Oleic acid (unsaturated fatty acid) was an exception, as it was above average harmful for paper strength without cationic starch and also heavily impaired the functioning of cationic starch. As a whole, these findings demonstrate that fatty acids, especially unsaturated ones, are the most relevant CPE compounds contributing to the reduced efficiency of cationic starch and decreased strength of unbleached softwood Kraft paper. This makes the cleaning of process waters by precipitating CPEs on the pulp fibers harmful for paper strength.

Scaling biosynthesis of bacterial nanocellulose (BNC) allowed samples of composite paper with an increased proportion of BNC to be obtained. This work aims to study BNC samples and bleached soft wood kraft pulp (BSKP) composite paper with a ratio of components varying across a wide range: 10:90, 30:70, 50:50, 60:40, 70:30, 90:10. The method of paper manufacturing was chosen based on the determinations of strength and deformation properties of composite samples with the BNC:BSKP ratio of 20:80. Surface application of BNT on BSKP handsheet provided for an increase in the strength values (tear resistance – by 37%, burst index – by 17%) and deformation characteristics (tension stiffness – by 66%, fracture work – by 8%, breaking length – by 4%) compared to a reference sample. The formation of composites is confirmed in all samples. Scanning electron spectroscopy revealed that paper composites comprise interlaced micro BSKP and nano BNC fibres. As the proportion of BNC in composites elevated, densification of the structure was observed due to an increased fraction of cross-linked nanosized elements. IR spectroscopy indicated the resemblance of cellulose structure in all samples. It was found that an increase in the degree of polymerisation of composite paper is directly proportional to an increase in the BNC amount in the samples. The filtering ability of composite paper samples against microorganisms in the culture liquid of the Medusomyces gisevii Sa-12 producer was studied. It should be noted that yeast retention is achieved with 70% BNC in the paper composite. The presented properties of the new material determine prospects for its use in filtering microorganisms.

Biodegradable paper cups coated with rice bran wax and whey protein isolate were designed to package popcorn. Coatings with different concentrations of whey protein isolate (5.5, 7.75, and 10% w/v) and rice bran wax (0.2, 0.4, and 0.6% w/v) were applied on the outer surface of the paper cups. Thickness, color changes, Young's modulus and tensile strength, water vapor transmission rate (WVTR) of the coated and uncoated cups, and also popcorns properties (pH, texture, and sensory properties) were evaluated. Water vapor transmission rate, Young's modulus, thickness, total color change index, and tensile strength of coated cups with the optimal coating formulation was 19.785 (g/m2 day), 11.810 (MPa), 276.583 (µm), 1.839, and 11.222 (MPa), respectively. The results showed that paper cup coating increased thickness and yellowness and reduced the brightness, Young's modulus, and WVTR. Coating had a positive effect on the pH and texture of popcorns packaged in coated cups than samples packed in uncoated cups (p, Biodegradable packaging is one of the best types of packaging that wishes not to harm the environment. Paper packaging coated with materials, such as rice bran wax and whey protein isolate, both of which are food waste, can improve paper color and resistance, and provide a good moisture barrier. This type of coating can be used in paper packaging of food such as snacks, noodle packaging, semi‐prepared foods, etc. This type of packaging can also maintain the physicochemical and sensory properties of food for a long time. Also, due to the edible nature of this type of coating, this coating can be used inside the package so that the printability of the packaging surface is not affected.

The aim of this study was to investigate the effect of using whey powder (different concentrations and treatment repetitions) as a probiotic agent on the quantitative and qualitative properties of stored bagasse intended for use in the pulp and paper industry. For this purpose, whey powder was added in three concentrations and the treatment was applied once or twice. After that, soda pulp was prepared under conventional conditions. Then, handsheets (80 g/m2) were made and tested in terms of paper properties, and the results were compared. The findings revealed that increasing the concentration of whey powder and the number of treatments significantly improved the pulp and paper characteristics, thus, using the treatment with 2% whey powder twice and 0.4% whey powder once led to the best results for bagasse protection in terms of quality of the raw material, pulp and handsheets.

Paper manufacturing on a global scale is a highly competitive market which requires to constantly improve the manufacturing process to be competitive. To decrease production cost paper manufactures, add filler material prior to sheet forming to replace costly wood fiber based raw material. This research project investigates the use of in-situ precipitated calcium carbonate produced in the presence of eucalyptus fiber material at a 41.0% filler level prior to beating. The in-situ filler containing eucalyptus fiber suspension was used on a 12’ (304mm) wide Laboratory Fourdrinier Paper Machine together with non-filler containing eucalyptus fiber material, and a commercial precipitated calcium carbonate filler material. The manufactured in-situ fiber suspension resulted in a higher ash retention compared to the addition of the powdered commercial PCC filler material. In addition to commercial filler material retention is improved at higher filler addition above 30%. The increased ash retention is linked to the increased micro fibrillation fiber material of the in-situ filler-fiber suspension forming neckless like particles on the fibers microfibrils. Mechanical paper properties showed an improvement for in-situ precipitated filler material compared to commercial filler material addition. Optical properties could be improved in comparison to the eucalyptus fiber without filler addition for in-situ precipitated filler material and a combination of in-situ and commercial filler material.

Transition towards carbon neutrality will require application of negative carbon emission technologies (NETs). This creates a new opportunity for the industry in the near future. The pulp and paper industry already utilizes vast amounts of biomass and produces large amounts of biogenic carbon dioxide. The industry is well poised for the use of bioenergy with carbon capture and storage (BECCS), which is considered as one of the key NETs. If the captured carbon dioxide can be used to manufacture green fuels to replace fossil ones, then this will generate a huge additional market where pulp and paper mills are on the front line. The objective of this study is to evaluate future trends and policies affecting the pulp and paper industry and to describe how a carbon neutral or carbon negative pulp and paper production process can be viable. Such policies include, as examples, price of carbon dioxide allowances or support for green fuel production and BECCS implementation. It is known that profitability differs depending on mill type, performance, energy efficiency, or carbon dioxide intensity. The results give fresh understanding on the potential for investing in negative emission technologies. Carbon capture or green fuel production can be economical with an emission trade system, depending on electricity price, green fuel price, negative emission credit, and a mill’s emission profile. However, feasibility does not seem to evidently correlate with the performance, technical age, or the measured efficiency of the mill.

Xylan is the primary hemicellulose in most hardwood species, especially in birch. Research has highlighted the exploitation of xylans as a strength-enhancing additive to paper due to the current trend for the effective utilization of biomass. In this paper, a new pulping process was proposed, which involved the extraction of xylan prior to pulping, followed by the re-adsorption of the pulp after the final stage in the digester, followed by a suitable bleaching process. The aim of this work was to bleach hardwood kraft pulp (brown pulp) with adsorbed birch xylan via hydrogen peroxide and study the effect of the bleaching parameters on the paper properties. The results showed that the optical properties of paper decreased; however, the mechanical properties increased after the brown pulp adsorbed birch xylan. During the bleaching process, better mechanical properties were obtained with shorter bleaching times and lower bleaching temperatures, initial pHs, and MgSO4 dosages. However, the optical properties were improved as the bleaching time, temperature, initial pH, and MgSO4 dosage were increased. The adsorption of birch xylan could effectively modify the mechanical properties of paper made from brown pulp under various phases.

Lean manufacturing (LM) is established as a best practice to improve the performance of manufacturing industries. Not all the manufacturing industries realize the benefits of LM practices specifically continuous process industries. The present research work is intended to study the advantages of implementing LM practices in an ethical paper industry which is a continuous production industry. Presently, the industry suffers with the problems such as lack of productivity, raw material wastes, underutilized resources, and lack of standard practices in the production. Gemba technique is adapted to record the information related to the present manufacturing environment. Based on the current state analysis, the feasible lean tools are selected and implemented such as 5S, Kaizen, and Total Productive Maintenance (TPM). The improvements have been noted as reduced tool change over time, reduced material wastes, effective utilization of resources and provide safety guidelines to workers and operations. The implications of these improvements increased the productivity also.

The adsorption of locust bean gum (LBG) onto Northern Bleached Softwood Kraft (NBSK) pulp improved paper tensile and burst strength and lowered refining energy by strengthening inter-fibre bonding. Adsorption kinetics and isotherms were investigated to develop a fundamental understanding of the adsorption mechanism. The adsorption rate followed pseudo-second-order kinetics and the activation energy was 99.34 kJ·mol−1, suggesting chemisorption. The adsorption rate constant increased rapidly with temperature from 25 to 45 °C (k = 1.93 to 24.03 g·mg−1·min−1), but the amount adsorbed at equilibrium decreased (qe = 1.91 to 0.48 mg·g−1 o.d. fibre). LBG adsorption to NBSK at 25 °C was consistent with the Langmuir adsorption model for LBG n = 5.00, and the equilibrium constant Kf = 2.57 mg·g−1·(mg·L−1)−1/n at 25 °C. Favorable adsorption conditions for negatively charged LBG were identified: 25 °C for 10 min, low dosage level ( 150 r.p.m.), acidic or neutral conditions (pH 2–7) without salt addition. Graphic abstract

Introduction. The Shchuchiy Bay is located in the western part of the skerry area of Lake Ladoga near the town of Priozersk. For almost 20 years, the bay has experienced an anthropogenic impact from the ingress of untreated wastewater from the Priozersk Pulp and Paper Mill (PPM). Systematic microbiological studies of the Shchuchiy Bay ecosystem were started in the middle of the 1970s by the Institute of Limnology of the Russian Academy of Sciences and continued after the PPM closure in 1986. Materials and methods. The ecosystem of the bay was studied in detail during the growing season of 2013–2014; periodic studies were carried out in 2015–2018. Retrospective data were also used for the analysis. Water samples were taken at four stations from the surface horizon. The following microbiological indicators were determined: the abundance of bacterioplankton and the percentages of various morphological types of bacterial cells. Results and discussion. A comparison of the quantitative level of development of the bacterial community in the bay in different periods showed a gradual decrease in the abundance of bacterioplankton as the anthropogenic impact weakened after the closure of the Priozersky PPM from 12.40 million cells ml–1 in 1987 to an average value of 2.62±1.03 million cells ml–1 in 2013–2018. A positive correlation was found between the concentration of bacteria and water temperature. The percentage of rod-shaped microorganisms in the water of the bay also decreased as the anthropogenic impact weakened from 73.4 % in 1987 to 53.1±7.6 % in 2013–2018, which indicated an improvement in water quality. Conclusion. A stable decrease in the abundance of bacteria from the level characteristic of highly polluted and eutrophic water bodies to the level characteristic of mesotrophic and mesotrophic-eutrophic water bodies is a reliable criterion for the restoration of the ecosystem of the Shchuchiy Bay to the state characteristic of similar bays of Lake Ladoga.

The sorption properties of organomineral composite sorbents have been investigated by ICP-MS method. The diatomite of the Jradzor deposit and bentonite of the Sarigyuh deposit (Armenia) were used as inorganic constituents. Diatomite serves as a structure-forming component and provides mass transfer due to its high porosity (V = 2.0 cm3/g) and large pore sizes (150–200 nm). Bentonite is responsible for the functionality of the sorbents. The organic component is also responsible for the functionality of the obtained sorbents. Paper pretreated with acids (nitric and phosphoric) was used as an organic component. A synthetic solution containing cations of heavy metals was used as an object of study. The experiments were carried out in static mode on a Jar-Test device.

The pulp and paper industry is primarily dependent on fibrous wood for pulp and paper production. However, this over-dependence on fibrous wood poses serious environmental challenges such as the diminishing of the fibrous wood stocks, deforestation, emission of greenhouse gases, and global warming. Therefore, to mitigate these environmental challenges associated with its utilization for paper and pulp production, other sustainable raw material sources can also be considered for the production of paper and pulp. There are enormous benefits associated with the utilization of non-wood fibres as an alternative and sustainable raw materials source for the production of paper and pulp. These benefits have in the recent past prompted millers in China, India, Brazil, and the USA to consider the utilization of non-wood fibres in paper and pulp production. In Kenya, the pulp and paper industry is very much dependent on fibrous wood for production and the industry is yet to fully embrace the utilization of nonwood fibres for paper and pulp production. Further, the dependence on fibrous wood has contributed significantly to the decline of paper pulp and paper production, deforestation, and rise in paper importations due to insufficient raw material supplies. The importation of paper and pulp products has further led to the collapse of the paper industry in Kenya. The sector stands a chance of revival and vibrancy through the utilization of the abundant agricultural residues and feedstocks lying in the agricultural fields across the country. Similar experiences elsewhere have proved that the abundance of agricultural waste can be utilized for the production of paper and pulp due to their excellent fibre content for specialty papers, and easy pulpability. The agricultural residues are therefore considered a quintessential alternative and sustainable source of raw materials for the pulp and paper industry. Moreover, their utilization will mitigate environmental impacts such as deforestation, climate change, and pollution .

High per- and polyfluorinated alkyl substance (PFAS) concentrations have been detected in agricultural soils in Southwest Germany. Discharges of PFAS-contaminated paper sludge and compost are suspected to be the cause of the contamination. Perfluorinated carboxylic acids (PFCAs) have been detected also in groundwater, drinking water, and plants in this area. Recently, previously unknown compounds have been identified by high-resolution mass spectrometry (HRMS). Major contaminants were polyfluorinated dialkylated phosphate esters (diPAPs) and N-ethyl perfluorooctane sulfonamide ethanol–based phosphate diester (diSAmPAP). In this study, HRMS screening for PFAS was applied to 14 soil samples from the contaminated area and 14 impregnated paper samples which were from a similar period than the contamination. The paper samples were characterized by diPAPs (from 4:2/6:2 to 12:2/12:2), fluorotelomer mercapto alkyl phosphates (FTMAPs; 6:2/6:2 to 10:2/10:2), and diSAmPAP. In soil samples, diPAPs and their transformation products (TPs) were the major contaminants, but also FTMAPs, diSAmPAP, and their TPs occurred. The distribution patterns of the carbon chain lengths of the precursor PFAS in soil samples were shown to resemble those in paper samples. This supports the hypothesis that paper sludge is a major source of contamination. The presence of major degradation products like PFCAs, FTSAs, or PFOS and their distribution of carbon chain lengths indicate the activity of biotic or abiotic degradation processes and selective leaching processes from the upper soil horizons. Graphical abstract Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03463-9.

The fibre characteristics of five Spondia mombin stands were studied to determine their suitability for pulp and paper production. Wood slivers obtained parallel to grain at three (3) different positions along the bole were macerated in combined identical amounts of glacial acetic acid plus hydrogen peroxide under heat at between 80-100o C. Macerated fibres were washed clean of mixture and mounted on slide for microscopic examination of fibre characteristics. Completely Randomized Design (CRD) was employed for the experiment. Data were analysed using one-way Analysis of Variance (ANOVA) while, the Duncan’s Multiple Range Test (DMRT) was used to separate means of significant differences among the treatments. Results show that significant differences existed in fibre characteristic of sampled trees, however the fibre length ranged from 0.98-1.0 mm, fibre diameter (18.22-21.47 um), lumen width (10.90-12.98 um) and cell wall thickness (3.86-4.60 um). Significant differences were also observed among the derived fibre characteristics, the Runkel ratio ranged from 0.66-8.89, elasticity coefficient (57.22-60.50 %), coefficient of rigidity (19.78-22.24 %), slenderness ratio (43.27-46.5). This implied that, the fibres of S. mombin were short and elastic which make the wood species an appropriate raw material for pulp and paper making especially when blended with other long fibre species.

Cellulose based nanomaterials have the great potential to be applied to paper as bulk additive or coating material to improve overall final properties, especially in secondary fiber. In the present work, the effect of applying different kinds of cellulose nanofibrils (CNF) to papers obtained from recycled fibers using size press on physical, mechanical and barrier properties was investigated and compared with the sole use of starch as coating material. The coating process of CNF was carried out by the addition of size press grade starch to coating suspension. As a cellulose source, wheat straw was evaluated and CNF was obtained through oxidative and enzymatic pretreatments. Results indicate that starch/CNF suspension improves the overall paper properties. As a result of the deposition of coating suspension contains of 4 % wt. periodate-oxidized CNF onto paper surface, tensile and burst indices of papersheets increased as 52.2 % and 194.4 %. Significant decreases were observed in air permeability as 69.8 %. Compression tests also have been conducted to evaluate papersheets end-use properties. In comparison to the other pretreated CNF, due to is lower viscosity, applying periodate-oxidized CNF as size press significantly increased the mechanical properties of the papers fabricated from the recycled pulps. TUBITAK-TEYDEBTurkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [1505]; Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate [1505, 5180044] This work was supported by TUBITAK-TEYDEB 1505 (The Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate 1505), Project No. 5180044. WOS:000703585400013 2-s2.0-85108063350

In this study, it was aimed to investigate the chemical and morphological suitability of using pseudo-stem which are formed in large amounts during the fruit harvesting of the banana plant (Musa sapientum) with a widespread agricultural area in the world, as raw material in the paper industry. The main chemical constituents of banana pseudo-stem holocellulose, α-cellulose and lignin were determined as %77.5, %51.0 and %12.7, respectively. Hot water solubility was 17.3%, cold water solubility 13.0%, alcohol and 1% NaOH solubility values were 9.2% and 33.3%, respectively. It has been determined that banana pseudo-stem waste fibers, which are similar to softwood fibers in terms of fiber length and hardwood fibers in terms of fiber width, have high slenderness and flexibility ratios with low Runkel ratio, rigidity coefficient and Mühlstep ratio. The results obtained from chemical and morphological analyzes indicated that banana pseudo stem waste is a suitable raw material for pulp and paper production., Bu çalışmada dünyada yaygın bir tarım alanına sahip muz bitkisinin (Musa sapientum) meyve hasadı sırasında oldukça fazla miktarda oluşan gövde atıklarının, kağıt endüstrisinde hammadde olarak kullanılabilirliğinin kimyasal ve morfolojik açıdan uygunluğunun araştırılması amaçlanmıştır. Muz yalancı gövdesinin başlıca kimyasal bileşenleri holoselüloz, α-selüloz ve lignin sırasıyla %77.5, %51.0 ve %12.7 olarak tespit edilmiştir. Sıcak su çözünürlüğü %17.3, soğuk su çözünürlüğü %13.0, alkol ve %1 NaOH çözünürlük değerleri ise sırasıyla %9.2 ve %33.3 olarak bulunmuştur. Lif uzunluğu bakımından iğne yapraklı ağaç odunu liflerine, lif genişliği bakımından ise yapraklı ağaç odunu liflerine benzeyen muz yalancı gövde atığı liflerinin düşük Runkel oranı, rijitlik katsayısı ve Mühlstep oranı ile yüksek narinlik ve esneklik oranlarına sahip olduğu tespit edilmiştir. Kimyasal ve morfolojik analizlerden elde edilen sonuçlar, muz yalancı gövde atıklarının kağıt hamuru ve kağıt üretimi için uygun bir hammadde olduğunu göstermiştir.

Paper based lateral flow systems are widely used biosensor platforms to detect biomolecules in a liquid sample. Proteins, bacteria, oligonucleotides, and nanoparticles were investigated in the literature. In this work we designed a magnetic platform including dual magnets and tested the flow of micron size immunomagnetic particles alone and when loaded with cells on two different types of papers. The wetting conditions of the paper and the applied external magnetic field are the two dominant factors affecting the particle and cell transport in paper. The images recorded with a cell phone, or with a bright field optical microscope were analyzed to measure the flow of particles and cells. The effect of wetting conditions and magnetic force were measured, and it was shown that in the worst case 90% of the introduced cells reached to the edge of the paper. The paper based magnetophoretic lateral flow systems can be used for cell assays.

Fraudulent papers from paper mills are a serious threat to the entire scientific community. Naunyn-Schmiedeberg’s Archives of Pharmacology has become the target of a massive attack of fraudulent papers originating from paper mills. This editorial highlights 20 important features we observed with paper mills and explains how the journal is responding to this serious threat to restore the integrity of science. Hopefully, this editorial is also helpful for editors of other scientific journals.

The purpose of present work was to obtain bactericidal materials using heulandite-clinoptilolite from the Rkoni plot of the Tedzami deposit, Eastern Georgia, to study their properties and use them as a filler for the production of bactericidal paper. Silver-, copper-, and zinc-containing microporous materials have been prepared using ion-exchange reactions between preliminary acid-treated zeolite microcrystals and a salt of a corresponding bioactive metal in the solid phase followed by washing with distilled water. Synthesized in such way adsorbent-ion-exchangers are characterized by X-ray energy dispersion spectra, powder X-ray diffraction patterns, and Fourier transform infra-red spectra. Obtained materials remain the zeolite crystal structure and contain over 130 mg/g of silver, 70 mg/g of copper, and 55 mg/g of zinc. Prepared materials show bacteriostatic activity towards gram-negative bacterium Escherichia coli, gram-positive bacteria Staphylococcus aureus and Bacillus subtilis, fungal pathogenic yeast Candida albicans, and a fungus Aspergilus niger. It was found that the mixtures of various forms exhibit a synergistic effect, and the silver form with additives of copper and zinc forms is most active against staphylococcus, and against other microorganisms, mixtures of copper and zinc forms are most effective.

An approach of green in situ synthesis single-step method was applied to produce antibacterial paper. The objective was to investigate the effect of precursor addition on the formation of zinc oxide particles using an in situ single-step method. Zinc chloride concentrations of 0.1, 0.3, 0.5, and 0.7 M were prepared and added into a solution of algae extract and bamboo pulp. The prepared pulps were tested and made into handsheets using a papermaking machine based on TAPPI T205 (2006). Morphological observation of treated papers was conducted using a field emission scanning electron microscope (FESEM). An average of 400 to 570 nm zinc oxide spherical-shaped particle was observed on the fibers of paper. The percentage of element composition of the treated paper were 15.08% to 34.08% of zinc and 17.45% to 32.59% of oxygen captured via scanning electron microscopy with energy dispersive X-ray (SEM-EDX) analysis. The crystallinity test was performed using X-ray dispersion (XRD). A higher percentage of precursors exhibited a more amorphous structure. A measurement of more than 30% increment of inhibition zone was obtained from 10.00 to 25.00 mm against S. aureus, S. choleraesuis, and E. coli. Precursors addition of more than 0.3 M would have the most potential to enhance the growth of zinc oxide via in situ preparation, hence providing better antibacterial properties of the prepared papers.

Natural yellow plant dyes and traditional medicines were used widely on historical papers in ancient China for religious reasons and conservation considerations. This study aims to evaluate some traditional yellow botanical sources of dyes that contain different chemical colorant compositions in order to understand their effects on the properties of traditional handmade paper. The physical and chemical changes in paper specimens treated with plant dyes were studied by examining properties such as the color, pH, thermogravimetric (TG) characteristics, tensile strength, folding endurance and microstructure by scanning electron microscopy (SEM). The results indicated that different colorants had different toning effects and that the main components, including carboxyl and ketone groups, could affect the paper stability at high temperatures. The results also revealed that the mechanical properties of paper specimens were improved after treatment with plant dyes. The significant improvements in the tensile strength and folding endurance and the slightly higher decomposition temperature of Amur cork tree-dyed paper could be ascribed to the strong interaction between the colorants’ main components and the fibers. The scientific evaluation of the property changes is therefore valuable information for weighing the advantages and disadvantages of the various yellow toning materials for paper conservation treatment.

A new coating method was developed, based on cellulose regenerated from an N-methylmorpholine N-oxide (NMMO) solution applied to paper. In particular, the purpose of this study was to compare the effectiveness of the “deep coating” method using cellulose regenerated from NMMO solution and the classic pulp refining process as methods to improve paper mechanical properties and overall quality. The “deep coating” name comes from the fact that the coating process is combined with subsequent heating of the coating before its final solidification. As a result of this operation, deep penetration of the cellulosic solution into the paper structure occurs. This increases the contact surface of the solution with the cellulosic fibers, which increases the strength properties of the paper structure. It was found that the cellulosic coating increased the apparent density of the paper, the tensile strength, the elongation, the resistance to bursting, and the double fold number. However, the coating also decreased the air permeability and the tear resistance of the paper samples. Despite some technological difficulties, this method could be an attractive solution in the case of a need for additional functionalization of a paper structure.