Search

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60-140 degrees C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60-140 degrees C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60-140 degrees C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60-140 degrees C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60-140 degrees C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

Successful energy management is a way to achieve energy efficiency in the pulp and paper industry (PPI), which is important for assuring energy supply security, for increasing economic competitiveness, and for mitigating greenhouse gases. However, research shows that although energy use within PPI can be reduced by 5.5-19.4% per year, some of this by energy management practices, energy management is not always implemented. Why is this so? What are the barriers to, and drivers of implementation? How can the barriers be overcome? A systematic review of barriers and drivers in energy management in the PPI within peer-reviewed scientific articles suggests that the world-wide events that affect energy supply, volatility, and use seemingly also affect the number and frequency of research articles on energy management in the PPI. The perception of energy management in the PPI seems to be dominated by the understanding that it can mostly be achieved through technological improvements aiming to improve energy efficiency. The main driver of energy management was shown to be economic conditions: high and unstable energy prices, followed by drivers such as the need to remain internationally competitive, collaboration and energy management systems. Meanwhile, examples of the most important barriers are technical risks, lack of access to capital, lack of time and other priorities, and slim organization. The success factors for enhancing drivers and overcoming barriers were continuous energy accounting, energy-related collaboration, energy-efficiency programmes, and benchmarking. Altogether, success factors for energy management for improved energy efficiency could be summarized in the 4M frameworkthe 4M for energy efficiency: mind, measure, monitor, and managethat could be used as the energy management memory-tool that could lead to improved energy efficiency in other sectors as well., Funding Agencies|Swedish Energy Agency [2015-002143]; Division of Energy Systems in the Department of Management and Engineering at Linkoping University

An innovative modular approach for facile design and construction of flexible microfluidic biosensor platforms based on a dry manufacturing "craft-and-stick" approach is developed. The design and fabrication of the flexible graphene paper electrode (GPE) unit and polyethylene tetraphthalate sheet (PET)6/adhesive fluidic unit are completed by an economic and generic xurographic craft approach. The GPE widths and the microfluidic channels can be constructed down to 300 mu m and 200 mu m, respectively. Both units were assembled by simple double-sided adhesive tapes into a microfluidic integrated GPE (MF-iGPE) that are flexible, thin (<0.5 mm), and lightweight (0.4 g). We further functionalized the iGPE with Prussian blue and glucose oxidase for the fabrication of MF-iGPE glucose biosensors. With a closed-channel PET fluidic pattern, the MF-iGPE glucose biosensors were packaged and sealed to protect the integrated device from moisture for storage and could easily open with scissors for sample loading. Our glucose biosensors showed 2 linear dynamic regions of 0.05-1.0 and 1.0-5.5 mmol L-1 glucose. The MF-iGPE showed good reproducibility for glucose detection (RSD < 6.1%, n = 6) and required only 10 mu L of the analyte. This modular craft-and-stick manufacturing approach could potentially further develop along the concept of paper-crafted model assembly kits suitable for low-resource laboratories or classroom settings., Funding Agencies|Royal Golden Jubilee Ph.D. Scholarship from the Thailand Research Fund under the Office of the Prime Ministry, the Royal Thai Government [PHD/0213/2560]

An innovative modular approach for facile design and construction of flexible microfluidic biosensor platforms based on a dry manufacturing "craft-and-stick" approach is developed. The design and fabrication of the flexible graphene paper electrode (GPE) unit and polyethylene tetraphthalate sheet (PET)6/adhesive fluidic unit are completed by an economic and generic xurographic craft approach. The GPE widths and the microfluidic channels can be constructed down to 300 mu m and 200 mu m, respectively. Both units were assembled by simple double-sided adhesive tapes into a microfluidic integrated GPE (MF-iGPE) that are flexible, thin (<0.5 mm), and lightweight (0.4 g). We further functionalized the iGPE with Prussian blue and glucose oxidase for the fabrication of MF-iGPE glucose biosensors. With a closed-channel PET fluidic pattern, the MF-iGPE glucose biosensors were packaged and sealed to protect the integrated device from moisture for storage and could easily open with scissors for sample loading. Our glucose biosensors showed 2 linear dynamic regions of 0.05-1.0 and 1.0-5.5 mmol L-1 glucose. The MF-iGPE showed good reproducibility for glucose detection (RSD < 6.1%, n = 6) and required only 10 mu L of the analyte. This modular craft-and-stick manufacturing approach could potentially further develop along the concept of paper-crafted model assembly kits suitable for low-resource laboratories or classroom settings., Funding Agencies|Royal Golden Jubilee Ph.D. Scholarship from the Thailand Research Fund under the Office of the Prime Ministry, the Royal Thai Government [PHD/0213/2560]

An innovative modular approach for facile design and construction of flexible microfluidic biosensor platforms based on a dry manufacturing "craft-and-stick" approach is developed. The design and fabrication of the flexible graphene paper electrode (GPE) unit and polyethylene tetraphthalate sheet (PET)6/adhesive fluidic unit are completed by an economic and generic xurographic craft approach. The GPE widths and the microfluidic channels can be constructed down to 300 mu m and 200 mu m, respectively. Both units were assembled by simple double-sided adhesive tapes into a microfluidic integrated GPE (MF-iGPE) that are flexible, thin (<0.5 mm), and lightweight (0.4 g). We further functionalized the iGPE with Prussian blue and glucose oxidase for the fabrication of MF-iGPE glucose biosensors. With a closed-channel PET fluidic pattern, the MF-iGPE glucose biosensors were packaged and sealed to protect the integrated device from moisture for storage and could easily open with scissors for sample loading. Our glucose biosensors showed 2 linear dynamic regions of 0.05-1.0 and 1.0-5.5 mmol L-1 glucose. The MF-iGPE showed good reproducibility for glucose detection (RSD < 6.1%, n = 6) and required only 10 mu L of the analyte. This modular craft-and-stick manufacturing approach could potentially further develop along the concept of paper-crafted model assembly kits suitable for low-resource laboratories or classroom settings., Funding Agencies|Royal Golden Jubilee Ph.D. Scholarship from the Thailand Research Fund under the Office of the Prime Ministry, the Royal Thai Government [PHD/0213/2560]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

Wild horse optimizer (WHO) is a recently proposed metaheuristic algorithm that simulates the social behavior of wild horses in nature. Although WHO shows competitive performance compared to some algorithms, it suffers from low exploitation capability and stagnation in local optima. This paper presents an improved wild horse optimizer (IWHO), which incorporates three improvements to enhance optimizing capability. The main innovation of this paper is to put forward the random running strategy (RRS) and the competition for waterhole mechanism (CWHM). The random running strategy is employed to balance exploration and exploitation, and the competition for waterhole mechanism is proposed to boost exploitation behavior. Moreover, the dynamic inertia weight strategy (DIWS) is utilized to optimize the global solution. The proposed IWHO is evaluated using twenty-three classical benchmark functions, ten CEC 2021 test functions, and five real-world optimization problems. High-dimensional cases (D = 200, 500, 1000) are also tested. Comparing nine well-known algorithms, the experimental results of test functions demonstrate that the IWHO is very competitive in terms of convergence speed, precision, accuracy, and stability. Further, the practical capability of the proposed method is verified by the results of engineering design problems., Funding Agencies|Sanming University [21YG01, 20YG14]; National Natural Science Foundation Breeding Project [PYT2103, PYT2105]; Fujian Natural Science FoundationNatural Science Foundation of Fujian Province [2021J011128]; Guiding Science and Technology Projects in Sanming City [2021-S-8]; Educational Research Projects of Young and Middle-Aged Teachers in Fujian Province [JAT200618]; Scientific Research and Development Fund of Sanming University [B202009]; Open Research Fund Program of Fujian Provincial Key Laboratory of Agriculture Internet of Things Application [ZD2101]

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

Industrial cyber-physical system products interleave hardware, software, and communication components. System complexity is increasing simultaneously with increased demands on quality and shortened time-to-market. To effectively support the development of such systems, we present languages and tools for comprehensive integrated model-based development that cover major phases such as requirement analysis, design, implementation, and maintenance. The model-based approach raises the level of abstraction and allows to perform virtual prototyping by simulating and optimizing system models before building physical products. Moreover, open standards and open source implementations enable model portability, tool reuse and a broader deployment. In this paper we present a general overview of the available solutions with focus on Modelica/OpenModelica, Bloqqi, and Acumen. The paper presents contributions to these languages and environments, including symbolic-numeric modeling, requirement verification, code generation, model debugging, design optimization, graphical modeling, and variant handling with traceability, as well a general discussion and conclusions., Funding Agencies|Strategic Research Area ELLIIT - Swedish government; Vinnova in the ITEA OPENPRODVinnova; Vinnova in the ITEA MODRIO projectVinnova; Vinnova in the ITEA OPENCPS projectVinnova; Vinnova in the ITEA EMPHYSIS projectVinnova; Vinnova in the ITEA EMBRACE projectVinnova; Swedish Strategic Research Foundation (SSF) in the LargeDyn project; Open Source Modelica Consortium

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

Industrial cyber-physical system products interleave hardware, software, and communication components. System complexity is increasing simultaneously with increased demands on quality and shortened time-to-market. To effectively support the development of such systems, we present languages and tools for comprehensive integrated model-based development that cover major phases such as requirement analysis, design, implementation, and maintenance. The model-based approach raises the level of abstraction and allows to perform virtual prototyping by simulating and optimizing system models before building physical products. Moreover, open standards and open source implementations enable model portability, tool reuse and a broader deployment. In this paper we present a general overview of the available solutions with focus on Modelica/OpenModelica, Bloqqi, and Acumen. The paper presents contributions to these languages and environments, including symbolic-numeric modeling, requirement verification, code generation, model debugging, design optimization, graphical modeling, and variant handling with traceability, as well a general discussion and conclusions., Funding Agencies|Strategic Research Area ELLIIT - Swedish government; Vinnova in the ITEA OPENPRODVinnova; Vinnova in the ITEA MODRIO projectVinnova; Vinnova in the ITEA OPENCPS projectVinnova; Vinnova in the ITEA EMPHYSIS projectVinnova; Vinnova in the ITEA EMBRACE projectVinnova; Swedish Strategic Research Foundation (SSF) in the LargeDyn project; Open Source Modelica Consortium

The energy efficiency gap is known as the difference between optimal level of energy efficiency and the actual level of achieved energy efficiency. Energy management has proven to further close the energy efficiency gap. Energy management may differ depending on whether it concerns a large, energy-intensive company or small and medium-sized enterprises (SMEs). SMEs are of high interest since they form a large share of the economy today. For SMEs, a lighter form of energy management, in the form of energy efficiency network participation, has proven to deliver sound energy efficiency impact, while for larger, energy-intensive firms, a certified energy management system may be more suitable. However, various barriers inhibit adoption of energy efficiency measures. While there is an array of research on barriers to and driving forces for energy efficiency in general, research on barriers to, and driving forces for, energy management is rare, one exception being a study of energy-intensive pulp and paper mills. This holds even more so for industrial SMEs. This paper aims to identify the barriers to, and drivers for, energy management in manufacturing SMEs. Results of this explorative study show that the top four barriers to energy management are lack of time/other priorities, non-energy-related working tasks are prioritized higher, slim organization, and lack of internal expert competences, i.e., mainly organizational barriers. The top four drivers for energy management are to reduce production waste, participation in energy efficiency networks, cost reduction from lower energy use, and commitment from top management. Furthermore, results show that energy management among the studied SMEs seems to not be as mature, even though the companies participated in an energy management capacity building program in the form of energy efficiency networks, which, in turn, shows a still largely untapped potential in the societal aim to reduce the energy efficiency and management gap, Funding Agencies|European CommissionEuropean CommissionEuropean Commission Joint Research Centre; Swedish Agency for Economic and Regional Growth, Region Gaevleborg; University of Gaevle

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

Industrial cyber-physical system products interleave hardware, software, and communication components. System complexity is increasing simultaneously with increased demands on quality and shortened time-to-market. To effectively support the development of such systems, we present languages and tools for comprehensive integrated model-based development that cover major phases such as requirement analysis, design, implementation, and maintenance. The model-based approach raises the level of abstraction and allows to perform virtual prototyping by simulating and optimizing system models before building physical products. Moreover, open standards and open source implementations enable model portability, tool reuse and a broader deployment. In this paper we present a general overview of the available solutions with focus on Modelica/OpenModelica, Bloqqi, and Acumen. The paper presents contributions to these languages and environments, including symbolic-numeric modeling, requirement verification, code generation, model debugging, design optimization, graphical modeling, and variant handling with traceability, as well a general discussion and conclusions., Funding Agencies|Strategic Research Area ELLIIT - Swedish government; Vinnova in the ITEA OPENPRODVinnova; Vinnova in the ITEA MODRIO projectVinnova; Vinnova in the ITEA OPENCPS projectVinnova; Vinnova in the ITEA EMPHYSIS projectVinnova; Vinnova in the ITEA EMBRACE projectVinnova; Swedish Strategic Research Foundation (SSF) in the LargeDyn project; Open Source Modelica Consortium

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

Industrial cyber-physical system products interleave hardware, software, and communication components. System complexity is increasing simultaneously with increased demands on quality and shortened time-to-market. To effectively support the development of such systems, we present languages and tools for comprehensive integrated model-based development that cover major phases such as requirement analysis, design, implementation, and maintenance. The model-based approach raises the level of abstraction and allows to perform virtual prototyping by simulating and optimizing system models before building physical products. Moreover, open standards and open source implementations enable model portability, tool reuse and a broader deployment. In this paper we present a general overview of the available solutions with focus on Modelica/OpenModelica, Bloqqi, and Acumen. The paper presents contributions to these languages and environments, including symbolic-numeric modeling, requirement verification, code generation, model debugging, design optimization, graphical modeling, and variant handling with traceability, as well a general discussion and conclusions., Funding Agencies|Strategic Research Area ELLIIT - Swedish government; Vinnova in the ITEA OPENPRODVinnova; Vinnova in the ITEA MODRIO projectVinnova; Vinnova in the ITEA OPENCPS projectVinnova; Vinnova in the ITEA EMPHYSIS projectVinnova; Vinnova in the ITEA EMBRACE projectVinnova; Swedish Strategic Research Foundation (SSF) in the LargeDyn project; Open Source Modelica Consortium

With the pressure of growing environmental problems, the world is changing, and so is the paradigm of design. Accordingly, the calls for change in design education are increasing throughout the literature day by day. As the designers of the future, students must be prepared for alternative scenarios. This paper provides insights into students learning outcomes and competencies related to repair and sustainability in the context of an assignment that integrates repair into design education. This assignment has been part of the masters degree design course at Linkoping University for the last 3 years. During these 3 years, 52 repair projects, including a diverse range of products, were developed. Aiming to find out the insights of this process, focus group sessions were conducted. As a result of these focus group sessions, 12 insights were developed, such as the concepts of brokenness, designed repair, and repair-worthy objects. Findings show that practices of repair constitute complex sites of learning, technical skill and knowledge which could enable novice designers to become competent in circular design. This paper is of value for design educators and researchers, especially those concerned with the repair and circular economy, as it can facilitate future attempts to further integrate circular strategies into design education.

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

Industrial cyber-physical system products interleave hardware, software, and communication components. System complexity is increasing simultaneously with increased demands on quality and shortened time-to-market. To effectively support the development of such systems, we present languages and tools for comprehensive integrated model-based development that cover major phases such as requirement analysis, design, implementation, and maintenance. The model-based approach raises the level of abstraction and allows to perform virtual prototyping by simulating and optimizing system models before building physical products. Moreover, open standards and open source implementations enable model portability, tool reuse and a broader deployment. In this paper we present a general overview of the available solutions with focus on Modelica/OpenModelica, Bloqqi, and Acumen. The paper presents contributions to these languages and environments, including symbolic-numeric modeling, requirement verification, code generation, model debugging, design optimization, graphical modeling, and variant handling with traceability, as well a general discussion and conclusions., Funding Agencies|Strategic Research Area ELLIIT - Swedish government; Vinnova in the ITEA OPENPRODVinnova; Vinnova in the ITEA MODRIO projectVinnova; Vinnova in the ITEA OPENCPS projectVinnova; Vinnova in the ITEA EMPHYSIS projectVinnova; Vinnova in the ITEA EMBRACE projectVinnova; Swedish Strategic Research Foundation (SSF) in the LargeDyn project; Open Source Modelica Consortium

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

Data driven organizations such as Amazon and Uber have raised the capabilities and expectations of customers to a new level by providing faster and cheaper products and services. The reviewed literature documented that 10-15% of the online products are returned and in many cases such products are not shelf-ready due to product obsolescence or slight wear and tear, thereby reducing profits. Many of these products are disposed of in landfills. There were very few publications that documented how integration of digitized product life cycle into the business model improves product returns and the remanufacturing processes. As societies continue on, environmentally responsible, digital journeys with connected devices and people, reverse supply chains and remanufacturing will play increased importance in fulfilling customers expanded expectations. The networks are evolving, wherein, data are collected from all phases of the product lifecycles from design, prototype, manufacturing, usage aftermarket, returns remanufacturing and recycling. The objective of this papers authors was to describe how all phases of product life cycles can be digitized to improve global reverse supply chains and remanufacturing. The authors performed a literature review and developed case studies to document current and to predict future transformational waves that will become increasingly used in many industrial sectors. The authors made recommendations about the importance of improved product design, reduced processing costs and increased use of remanufactured products based upon data on returns to manufacturers and service providers. This paper contributes to research by providing a framework of a digitized product life cycle integrated with the business process phases including remanufacturing and supported with real-world case studies for practitioners and academicians. The authors outlined potential future topics for academic researchers and practitioners, for expanding usage of digital tool, Funding Agencies|The Swedish Foundation for Strategic Environmental Research [2014/16]

This paper presents a tracking system using magnetometers, possibly integrable in a deep brain stimulation (DBS) electrode. DBS is a treatment for movement disorders where the position of the implant is of prime importance. Positioning challenges during the surgery could be addressed thanks to a magnetic tracking. The system proposed in this paper, complementary to existing procedures, has been designed to bridge preoperative clinical imaging with DBS surgery, allowing the surgeon to increase his/her control on the implantation trajectory. Here the magnetic source required for tracking consists of three coils, and is experimentally mapped. This mapping has been performed with an in-house three-dimensional magnetic camera. The system demonstrates how magnetometers integrated directly at the tip of a DBS electrode, might improve treatment by monitoring the position during and after the surgery. The three-dimensional operation without line of sight has been demonstrated using a reference obtained with magnetic resonance imaging (MRI) of a simplified brain model. We observed experimentally a mean absolute error of 1.35 mm and an Euclidean error of 3.07 mm. Several areas of improvement to target errors below 1 mm are also discussed.

Unique digital circuit outputs, considered as physical unclonable function (PUF) circuit outputs, can facilitate a secure and reliable secret key agreement. To tackle noise and high correlations between the PUF circuit outputs, transform coding methods combined with scalar quantizers are typically applied to extract the uncorrelated bit sequences reliably. In this paper, we create realistic models for these transformed outputs by fitting truncated distributions to them. We also show that the state-of-the-art models are inadequate to guarantee a target reliability level for all PUF outputs, which also means that secrecy cannot be guaranteed. Therefore, we introduce a quality of security parameter to control the percentage of the PUF circuit outputs for which a target security level can be guaranteed. By applying the finite-length information theory results to a public ring oscillator output dataset, we illustrate that security guarantees can be provided for each bit extracted from any PUF device by eliminating only a small subset of PUF circuit outputs. Furthermore, we conversely show that it is not possible to provide reliability or security guarantees without eliminating any PUF circuit output. Our holistic methods and analyses can be applied to any PUF type, as well as any biometric secrecy system, with continuous-valued outputs to extract secret keys with low hardware complexity., Funding Agencies|ELLIIT funding; ZENITH Research and Leadership Career Development Fund; German Federal Ministry of Education and Research (BMBF) [16KISK001K, EXC 2050/1, 390696704]; U.S. National Science Foundation (NSF) [CNS-2128448, ECCS-2335876]