Search

This work addresses the use of remote sensing imagery to quantify the built environment and its spatial and temporal changes. It identifies building footprint map, building location map and built-up area map as information products that can be used to quantify physical exposure, one of the variables required in disaster risk assessments. The paper also reviews urban land use maps and urban classes in land cover maps as potential source for deriving exposure information. The paper focuses on the latest generation of satellite-borne remote sensing imaging systems that deliver high-resolution optical imagery able to resolve buildings and other three-dimensional man-made constructions. This work also reviews the semantics, the spatial unit used to define physical exposure, image processing procedures and change techniques.

Geospatial database creation for landslide susceptibility mapping is often an almost inhibitive activity. This has been the reason that for quite some time landslide susceptibility analysis was modelled on the basis of spatially related factors. This paper presents the use of frequency ratio, fuzzy logic and multivariate regression models for landslide susceptibility mapping on Cameron catchment area, Malaysia, using a Geographic Information System (GIS) and remote sensing data. Landslide locations were identified in the study area from the interpretation of aerial photographs, high resolution satellite images, inventory reports and field surveys. Topographical, geological data and satellite images were collected, processed, and constructed into a spatial database using GIS and image processing tools. There were nine factors considered for landslide susceptibility mapping and the frequency ratio coefficient for each factor was computed. The factors chosen that influence landslide occurrence were: topographic slope, topographic aspect, topographic curvature and distance from drainage, all from the topographic database; lithology and distance from lineament, taken from the geologic database; land cover from TM satellite image; the vegetation index value from Landsat satellite images; and precipitation distribution from meteorological data. Using these factors the fuzzy membership values were calculated. Then fuzzy operators were applied to the fuzzy membership values for landslide susceptibility mapping. Further, multivariate logistic regression model was applied for the landslide susceptibility. Finally, the results of the analyses were verified using the landslide location data and compared with the frequency ratio, fuzzy logic and multivariate logistic regression models. The validation results showed that the frequency ratio model (accuracy is 89%) is better in prediction than fuzzy logic (accuracy is 84%) and logistic regression (accuracy is 85%) models. Results show that, among the fuzzy operators, in the case with “gamma” operator (λ = 0.9) showed the best accuracy (84%) while the case with “or” operator showed the worst accuracy (69%).

This paper presents landslide susceptibility analysis around the Cameron Highlands area, Malaysia using a geographic information system (GIS) and remote sensing techniques. Landslide locations were identified in the study area from interpretation of aerial photographs and field surveys. Topographical, geological data and satellite images were collected, processed, and constructed into a spatial database using GIS and image processing. Ten landslide occurrence factors were selected as: topographic slope, topographic aspect, topographic curvature and distance from drainage, lithology and distance from lineament, soil type, rainfall, land cover from SPOT 5 satellite images, and the vegetation index value from SPOT 5 satellite image. These factors were analyzed using an advanced artificial neural network model to generate the landslide susceptibility map. Each factor’s weight was determined by the back-propagation training method. Then, the landslide susceptibility indices were calculated using the trained back-propagation weights, and finally, the landslide susceptibility map was generated using GIS tools. The results of the neural network model suggest that the effect of topographic slope has the highest weight value (0.205) which has more than two times among the other factors, followed by the distance from drainage (0.141) and then lithology (0.117). Landslide locations were used to validate the results of the landslide susceptibility map, and the verification results showed 83% accuracy. The validation results showed sufficient agreement between the computed susceptibility map and the existing data on landslide areas.

This paper compares different image processing routines to identify suitable remote sensing variables for urban classifi- cation in the Marion County, Indiana, USA, using a Landsat 7 Enhanced Thematic Mapper Plus (ETM� ) image. The ETMmultispectral, panchromatic, and thermal images are used. Incorporation of spectral signature, texture, and surface temperature is examined, as well as data fusion techniques for combining a higher spatial resolution image with lower spatial resolution multispectral images. Results indicate that incorporation of texture from lower spatial resolution images or of a temperature image cannot improve classification accuracies. However, incorporation of textures derived from a higher spatial resolution panchromatic image improves the classification accuracy. In particular, use of data fusion result and texture image yields the best classifi- cation accuracy with an overall accuracy of 78 percent and a kappa index of 0.73 for eleven land use and land cover classes.

The use of low cost scanning techniques in association with image processing is considered for land use/land cover mapping in part of the Sahel. This paper describes variations in the use of a Sharp JX 320 colour scanner and associated software in capturing satellite diapositive imagery (at 1:1 000 000) and thematic map data on a PC with the aim of developing a method for using scanned data in a GIS system. Optimal image scanning was achieved using PC‐Quickscan II with the MTR set to strong and RGB lightness at 100%. Scanning at 300 dpi developed a dot (pixel) size representing 86.7m on the ground. Thematic map scanning was improved by using the Image‐In program and the black and white lineart format set with no colour controls or edge correction. The spatial resolution of the digitised maps was 173.4m. Generally scanning imagery was best achieved through PC‐Quickscan because no editing was required. Since editing thematic maps was essential because extraneous lines and shadow was picked up, Imag...

In this paper, I describe a set of procedures that automate forest disturbance mapping using a pair of Landsat images. The approach is built on the traditional pair-wise change detection method, but is designed to extract training data without user interaction and uses a robust classification algorithm capable of handling incorrectly labeled training data. The steps in this procedure include: i) creating masks for water, non-forested areas, clouds, and cloud shadows; ii) identifying training pixels whose value is above or below a threshold defined by the number of standard deviations from the mean value of the histograms generated from local windows in the short-wave infrared (SWIR) difference image; iii) filtering the original training data through a number of classification algorithms using an n-fold cross validation to eliminate mislabeled training samples; and finally, iv) mapping forest disturbance using a supervised classification algorithm. When applied to 17 Landsat footprints across the U.S. at five-year intervals between 1985 and 2010, the proposed approach produced forest disturbance maps with 80 to 95% overall accuracy, comparable to those obtained from traditional approaches to forest change detection. The primary sources of mis-classification errors included inaccurate identification of forests (errors of commission), issues related to the land/water mask, and clouds and cloud shadows missed during image screening. The approach requires images from the peak growing season, at least for the deciduous forest sites, and cannot readily distinguish forest harvest from natural disturbances or other types of land cover change. The accuracy of detecting forest disturbance diminishes with the number of years between the images that make up the image pair. Nevertheless, the relatively high accuracies, little or no user input needed for processing, speed of map production, and simplicity of the approach make the new method especially practical for forest cover change analysis over very large regions.