Search

This study evaluates the potential use of discarded plasterboard paper as fibers from buildings to reinforce concrete. Various concentrations of wastepaper fibers (0.5%, 1%, 1.5%, 2%, and 2.5% by weight of the binder) were investigated in this research. To mitigate the water absorption effect of the paper fibers, metakaolin was employed as a partial cement replacement. The results demonstrate that the inclusion of the wastepaper fiber enhances the mechanical and durability performance of the concrete. The optimal fiber proportion was identified as 1%, leading to a 29% increase in the compressive strength, a 38% increase in the splitting tensile strength, a 12% decrease in the water absorption, and a 23% decrease in the drying shrinkage with respect to the concrete containing 20% metakaolin. However, exceeding this optimal fiber content results in decreased mechanical and durability properties due to the fiber agglomeration and non-uniform fiber distribution within the concrete matrix. Based on the microstructural analysis, the improved performance of the concrete is ascribed to decreased porosity, more refined pore structure, and reduced propagation of microcracks within the concrete matrix in the presence of wastepaper fiber. According to the results, concrete containing 20% metakaolin and 1% wastepaper fiber exhibits durability and mechanical properties comparable to those of the traditional concrete. This finding highlights the significant promise of reducing dependency on conventional cement and incorporating suitable recycled materials, such as discarded plasterboard, and secondary by-products like metakaolin. Such a strategy encourages the preservation of resources, reduction in carbon dioxide emissions, and a decrease in the ecological footprint resulting from concrete production. [ABSTRACT FROM AUTHOR]

Sensitivity analysis of influencing factors on frost resistance is carried out in this paper, and a two-stage neural network model based on grey theory and Back Propagation Neural Networks (BPNNs) is established for the sake of predicting the frost resistance of active-admixture recycled concrete quickly and accurately. Firstly, the influence degree of cement, water, sand, natural aggregate, recycled aggregate, mineral powder, fly ash, fiber and air-entraining agent on the frost resistance of active-admixture recycled-aggregate concrete was analyzed based on the grey system theory, and the primary and secondary relationships of various factors were effectively distinguished. Then, the input layer of the model was determined as cement, water, sand, recycled aggregate and air-entraining agent, and the output layer was the relative dynamic elastic modulus. A total of 120 datasets were collected from the experimental data of another author, and the relative dynamic elastic modulus was predicted using the two-stage BPNN prediction model proposed in this paper and compared with the BPNN prediction results. The results show that the proposed two-stage BPNN model, after removing less-sensitive parameters from the input layer, has better prediction accuracy and shorter run time than the BPNN model. [ABSTRACT FROM AUTHOR]

The global surge in environmental pollution, largely attributed to industrialization, has fueled a pressing need for sustainable solutions. In response, the construction sector is increasingly focusing on bio-based materials such as hemp, recognized for its low environmental footprint and prominent carbon-negative quality. As designers, housebuilders, and an environmentally conscious society pivot towards ecological alternatives to standard building materials, hempcrete emerges as a promising candidate. As a composite material mainly made from hemp hurd/shiv, water, and lime, hempcrete offers the ability to sequester carbon long after its incorporation into structures. As a result, the hemp cultivation process—which can be completed within less than four months—ensures that more carbon is absorbed during production and deployment than emitted, e.g., per one study, sequestration on the order of 300 kg of CO2 per m3 of hempcrete. In comparison to concrete, hempcrete offers a more sustainable footprint, given its recyclability post life cycle. This state-of-the-art review paper delves deep into different aspects of hempcrete, summarizing its multifaceted attributes, particularly its compressive strength. Based on the study conducted, the paper also suggests strategies to augment this strength, thereby transitioning hempcrete from a non-load-bearing material to one capable of shouldering significant weight. As architects and designers consistently strive to align their projects with high ecological standards, focusing not just on aesthetic appeal but also environmental compatibility, hempcrete becomes an increasingly fitting solution for the future of construction. [ABSTRACT FROM AUTHOR]

This paper is grounded on the following information: (1) Disposable masks primarily consist of polypropylene fiber, which exhibits excellent flexibility. (2) China has extensive coal gangue deposits that pose a significant environmental hazard. (3) Coal gangue concrete exhibits greater fragility compared to regular concrete and demonstrates reduced resistance to deformation. With the consideration of environmental conservation and resource reutilization, a preliminary concept suggests the conversion of discarded masks into fibers, which can be blended with coal gangue concrete to enhance its mechanical characteristics. In this paper, the stress–strain law of different mask fiber–doped coal gangue concrete (DMGC) under uniaxial compression is studied when the matrix strength is C20 and C30, and the effect of mask fiber content on the mechanical behavior and energy conversion relationship of coal gangue concrete is analyzed. The experimental results show that when the content of mask fiber is less than 1.5%, the strength, elastic modulus, deformation resistance, and energy dissipation of the concrete increase with mask fiber content. When the amount of mask fiber is more than 1.5%, because the tensile capacity and energy dissipation level of concrete produced by the mask fiber cannot compensate for the compression and deformation resistance of concrete of the same quantity and because excess fiber is difficult to evenly mix in the concrete, there are pore defects in concrete, which decreases the concrete strength due to the increase in mask fiber. Therefore, adding less than 1.5% mask fiber helps to improve the ductility, toughness, impermeability, and oxidation and control the cracking of coal gangue concrete. Based on Weibull theory, a constitutive model of DMGC is established, which fits well with the results of a uniaxial test, providing support for understanding the mechanical law of mask fiber–doped concrete. [ABSTRACT FROM AUTHOR]

With a large number of railroad and highway tunnels opening for operation, the diseases caused by hidden lining defects are increasing. The study of flow characteristics of freshly mixed concrete during tunnel lining casting is the key to revealing the formation mechanism of hidden defects. This paper revealed the location of blank lining formation by investigating the circumferential and longitudinal flow characteristics of concrete in the vault during tunnel pouring to provide suggestions for improving the quality of tunnel lining pouring for the various projects. This paper adopted the method of indoor testing, selected the suitable working conditions and flow parameters, validated the accuracy of the test with a numerical simulation, and simulated the secondary lining pouring process of the tunnel arch from the circumferential direction and longitudinal direction. This revealed the flow characteristics of the freshly mixed concrete in the process of pouring the arch lining. The flow of concrete in the arch lining was basically characterized by two major features which were similar to the flow in the pumping pipe and the layered flow. It also revealed the relationship between the concrete flow rate, flow distance, and the location of the formation of the blank lining risk zone with the slump of the concrete, the pumping pressure, and the radius of the tunnel. [ABSTRACT FROM AUTHOR]

Fire is considered a common hazard for civil structures. Public and administrative buildings are commonly designed by considering the standard fire rating and, in many cases, contain large compartments with central domes, in which fire growth can be significant. Moreover, tanks and underground fortified structures may be constructed as domes to support the heavy soil above. This paper numerically addressed such a case. First, an axisymmetric finite element model was developed and validated to predict the dome's transient, thermal, structural, and thermal-structural behavior. Next, the model was used to conduct a parametric study to investigate the effects of the dome ring reinforcement, thickness, stiffness, central angle, base restraints, load type (external pressure or gravitational), and load ratio on the fire endurance of the dome. Design recommendations to increase the fire endurance of concrete domes were formulated based on the parametric study. [ABSTRACT FROM AUTHOR]

This paper explores the new potential strategy of using fine recycled aggregates (fRA) derived from waste 3D printed concrete (3DPC) as a substitute for cement in additive manufacturing. This study hypothesizes that fRA can optimize mixture design, reduce cement content, and contribute to sustainable construction practices. Experimental programs were conducted to evaluate the fresh and hardened properties, printability window, and buildability of 3DPC mixes containing fRA. Mixes with replacement rates of cement with fRA by 10 vol%, 20 vol%, 30 vol%, 40 vol%, and 50 vol% were produced. A comprehensive experimental protocol consisting of rheological studies (static and dynamic yield stress), dynamic elastic modulus determination (first 24 h of hydration), flexural and compressive strengths (2 d and 28 d), and an open porosity test was performed. The obtained results were verified by printing tests. In addition, an economic and environmental life cycle assessment (LCA) of the mixes was performed. The results indicate that up to 50 vol% cement replacement with fRA is feasible, albeit with some technical drawbacks. While fRA incorporation enhances sustainability by reducing CO2 emissions and material costs, it adversely affects the printability window, green strength, setting time, and mechanical properties, particularly in the initial curing stages. Therefore, with higher replacement rates (above 20 vol%), potential optimization efforts are needed to mitigate drawbacks such as reduced green strength and buildability. Notably, replacement rates of up to 20 vol% can be successfully used without compromising the overall material properties or altering the mixture design. The LCA analysis shows that reducing the cement content and increasing the fRA addition results in a significant reduction in mix cost (up to 24%) and a substantial decrease in equivalent CO2 emissions (up to 48%). In conclusion, this study underscores the potential of fRA as a sustainable alternative to cement in 3D printed concrete. [ABSTRACT FROM AUTHOR]

Rubber concrete has been applied to a certain extent in fatigue-resistant structures due to its good durability. Based on a cohesive model of rubber composed of a five-phase material containing mortar, aggregate, rubber, aggregate-mortar interfacial transition zone (ITZ), and rubber-mortar ITZ, this paper studies the influence of the cohesive parameters in the rubber-mortar ITZ on the fatigue problem of rubber concrete on the mesoscopic scale. As the weak part of cement-based composite materials, the ITZ has a great influence on the mechanical properties and durability of concrete, but the performance of the ITZ is difficult to test in macro experiments, resulting in difficulties in determining its simulation parameters. Based on the cohesive model with a rubber content of 5%, this study uses Monofactor analysis and the Plackett-Burman test to quickly and effectively determine the primary and secondary influences of the cohesive model parameters in the rubber-mortar ITZ; further, the response surface method is used to optimize the cohesive parameters in the rubber-mortar ITZ, and the numerical simulation results after optimizing the cohesive parameters are compared and analyzed with the simulation results before optimization. The results show that, under the setting of the optimized parameters, the simulation results of each item of the optimal cohesive model parameters in the rubber-mortar ITZ are in line with the reality and closer to the experimental data, and they are also applicable to rubber concrete models with different rubber dosing. [ABSTRACT FROM AUTHOR]

Cement-based materials encompass a broad spectrum of construction materials that utilize cement as the primary binding agent. Among these materials, concrete stands out as the most commonly employed. The cement, which is the principal constituent of these materials, undergoes a hydration reaction with water, playing a crucial role in the formation of the hardened composite. However, the exothermic nature of this reaction leads to significant temperature rise within the concrete elements, particularly during the early stages of hardening and in structures of substantial thickness. This temperature rise underscores the critical importance of predictive modeling in this domain. This paper presents a review of modeling approaches designed to predict temperature and accompanying moisture fields during concrete hardening, examining different levels of modeling accuracy and essential input parameters. While modern commercial finite element method (FEM) software programs are available for simulating thermal and moisture fields in concrete, they are accompanied by inherent limitations that engineers must know. The authors further evaluate effective commercial software tools tailored for predicting these effects, intending to provide construction engineers and stakeholders with guidance on managing temperature and moisture impacts in early-age concrete. [ABSTRACT FROM AUTHOR]

This paper brings a new insight into understanding the influence of macrocapsules in packing systems, which can be useful in designing the inert structure of self-healing concrete. A variety of tubular macrocapsules, in terms of types and sizes, was used to assess the capsules' effect in the packing, together with various aggregate types and fractions. The voids ratios (U) of aggregate mixtures were evaluated experimentally and compared with the prediction via the particle packing model of Dewar. The packing of coarse particles was found to be considerably affected by the presence of macrocapsules, while no capsules' effect on the packing of fine particles was attained. A higher capsule dosage and capsule aspect ratio led to a higher voids ratio. In the formulation of the inert structure, the packing disturbance due to capsules can be minimised by increasing the content of fine aggregates over coarse aggregates. Dewar's model showed a good compatibility with experimental results in the absence of capsules. However, the model needed to be upgraded for the introduction of tubular macrocapsules. Accordingly, the effect of macrocapsules was extensively analysed and a 'U model' for capsules (with some limitations) was finally proposed, offering a high predicting accuracy. [ABSTRACT FROM AUTHOR]

This paper presents a study on the combined use of two by-products, namely quarry dust (QD) and ferronickel slag (FNS), as a full substitute for natural sand to improve the greenness of concrete production. Quarry dust was used in increments of 25% to a maximum of 75% substitution, where nickel slag was used as the remaining proportion of fine aggregate. All the combinations of quarry dust and nickel slag were found to be compliant with AS 2758.1 and they showed notably better grading than 100% sand. In this research, standard concrete tests, such as the slump test for fresh concrete, and compression, tensile and shrinkage tests for hardened concrete, were conducted. Scanning electron microscopy and X-ray diffraction analysis were also conducted for microstructural investigation. The results concluded that the combinations of quarry dust and nickel slag in concrete as a whole substitution of sand provide similar results for these properties. Specifically, 25% quarry dust with 75% nickel slag proved to be the most promising alternative to sand, with compressive and splitting tensile strengths of 62 and 4.29 MPa, respectively, which were 16% and 20% higher than those of the control mix. Also, lower drying shrinkage was observed for this combination compared to the control mix. The higher strength is attributed to the rough texture and angular shape of both quarry dust and nickel slag providing a better mechanical interlocking. The validity of this result has also been confirmed through image analysis of micrographs from various specimens. In microstructural investigations, specimens with QD and FNS exhibited fewer voids and a more compact surface compared to the control specimen. This shows the potential for further research into the use of quarry dust and nickel slag in the production of green concrete. [ABSTRACT FROM AUTHOR]

The reasonable and effective application of waste tires and discarded concrete in concrete is an important branch of green concrete development. This paper investigates the effects of the inorganic modification mode on the basic mechanical properties of rubber recycled concrete based on indoor tests. Inorganic modification, such as water washing, acid washing, and alkaline washing modification, was mainly used to treat and modify rubber particles. The factors affecting the compressive strength, the splitting tensile strength, the flexural strength, the axial compressive strength, and the modulus of elasticity of modified rubber recycled concrete were analyzed. The study results show that the incorporation of recycled aggregates and rubber reduced the mechanical properties of concrete, with the compressive and splitting tensile strengths showing the greatest reductions of 27.36% and 27.24%, respectively. Three modification methods significantly improved the mechanical properties of rubber recycled concrete. The alkali washing modification method was the most effective, maximally improving the mechanical properties of rubber recycled concrete by 7.53–15.51%. The effects of the three modifications on the mechanical properties of concrete were ranked as follows: alkali washing > acid washing > water washing. This study provides a data basis for the practical application of rubber recycled concrete in engineering and a test basis for the development of green concrete. [ABSTRACT FROM AUTHOR]

Coda waves are highly sensitive to changes in medium properties and can serve as a tool for structural health monitoring (SHM). However, high sensitivity also makes them susceptible to noise, leading to excessive dispersion of monitoring results. In this paper, a coda wave multi-feature extraction method is proposed, in which three parameters, the time shift, the time stretch, and the amplitude variation of the wave trains within the time window, are totally derived. These three parameters are each mapped to the temperature variations of concrete beams, and then combined together with their optimal weight coefficients to give a best-fitted temperature–multi-parameter relationship that has the smallest errors. Coda wave signals were collected from an ultrasonic experiment on concrete beams within an environmental temperature range of 14 °C~21 °C to verify the effectiveness of the proposed method. The results indicate that the combination of multi-features derived from coda wave signals to quantify the medium temperature is feasible. Compared to the relationship established by a single parameter, the goodness-of-fit is improved. During identification, the method effectively reduces the dispersion of identification errors and mitigates the impact of noise interference on structural state assessment. Both the identification accuracy and stability are improved by more than 50%, and the order of magnitude of the identification accuracy is improved from 1 °C to 0.1 °C. [ABSTRACT FROM AUTHOR]

Impact tests on post-fire concrete confined by Carbon Fiber-Reinforced Polymer/Plastic (CFRP) sheets were carried out by using Split Hopkinson Pressure Bar (SHPB) experimental setup in this paper, with emphasis on the effect of exposed temperatures, CFRP layers and impact velocities. Firstly, according to the measured stress-strain curves, the effects of experiment parameters on concrete dynamic mechanical performance such as compressive strength, ultimate strain and energy absorption are discussed in details. Additionally, temperature caused a softening effect on the compressive strength of concrete specimens, while CFRP confinement and strain rate play a hardening effect, which can lead to the increase in dynamic compressive strength by 1.8 to 3.6 times compared to static conditions. However, their hardening mechanisms and action stages are extremely different. Finally, nine widely accepted Dynamic Increase Factor (DIF) models considering strain rate effect were summarized, and a simplified model evaluating dynamic compressive strength of post-fire concrete confined by CFRP sheets was proposed, which can provide evidence for engineering emergency repair after fire accidents. [ABSTRACT FROM AUTHOR]

Chemical shrinkage (CS) is an intrinsic parameter that may affect the early age cracking of paste, mortar and concrete. It is well known as the driving force of self-desiccation, autogenous shrinkage (AGS) and drying shrinkage. During the first stage of cement hydration (at the initial setting time), the CS and AGS are equal. In the hardened stages, there is a difference in values between the two shrinkage parameters. This paper is a comprehensive review on CS and AGS, measurement techniques, modeling and prediction of different cementitious systems. Based on the various experimental studies, chemical shrinkage depends on the water to binder ratio (w/b) and is proportional to the degree of hydration. A low w/b ratio leads to high CS and AGS. The composition of cement has an effect on both CS and AGS. Also, incorporating supplementary cementitious materials (SCMs) affects both shrinkage parameters. It is concluded that adding fly ash (FA) to concrete contributes to CS and AGS reductions. However, this is not the case when concrete contains slag. More than 170 references were consulted including 35 which were published after 2020. According to the authors knowledge, there is no published work on the effect of fibers, especially bio-fibers, on the chemical shrinkage of cement-based composites. Therefore, in addition to traditional chemical shrinkage of cementitious systems, this review includes a section on recent papers conducted by the authors on the effect of bio-fibers on the chemical shrinkage of cement composites. [ABSTRACT FROM AUTHOR]

The differences in physical properties, chemical properties, and mechanical properties between reclaimed concrete aggregate and natural aggregate are discussed in this paper. In this paper, the commonly used improvement techniques of recycled concrete aggregate are reviewed. Physical modification involves peeling the attached mortar layer using mechanical and thermodynamic means, including mechanical grinding and shaping, heat treatment, and microwave or electric pulse treatment. Chemical modification is based on the chemical reaction of some materials with recycled aggregate attached mortar, including acid treatment removal, water glass strengthening, carbonation strengthening, inorganic slurry strengthening, and polymer strengthening. Microbial modification is mainly based on the metabolic activity of specific microorganisms that induce carbon deposition modification. The results show that the reinforced technology of recycled aggregate has made some progress in improving the performance of recycled aggregate, but there are still some problems, such as inconsistent strengthening effects and the unstable compatibility of composite materials. In this paper, future research directions, such as the development of new strengthening materials and the integration of multi-functional strengthening technology, are described in order to provide some theoretical support for the utilization of recycled concrete aggregate. [ABSTRACT FROM AUTHOR]

The poor performance of recycled concrete aggregate (RCA) leads to greater creep in recycled aggregate concrete (RAC) compared to natural aggregate concrete (NAC). To enhance the quality of RCA, this paper utilizes a 2% concentration of a nano-SiO2 (NS) solution for pre-soaking RCA. This study aims to replace natural aggregate (NA) with NS-modified recycled aggregate (SRCA) and investigate the creep and shrinkage properties of NS-modified recycled aggregate concrete (SRAC) at various SRCA replacement rates. Subsequently, the creep and shrinkage strains of NAC, SRAC, and RAC are simulated using the finite element method. Finally, a comparative analysis is conducted with the predicted creep and shrinkage strains from CEB-FIP, ACI, B3, and GL2000 models. The experimental results indicate that the creep and shrinkage deformation of SRAC increases with the SRCA replacement rate. Compared to NAC, the creep and shrinkage deformation of SRAC at replacement rates of 30%, 50%, 70%, and 100% increased by 2%, 7%, 13%, and 30%, respectively. However, when 100% of the natural aggregate is replaced with SRCA, the creep and shrinkage deformation decreases by 7% compared to RAC. Moreover, the CEB-FIP and ACI models can predict the creep and shrinkage deformation of concrete reasonably well. [ABSTRACT FROM AUTHOR]

One of the most challenging elements of modeling the behaviour of reinforced concrete (RC) walls is combining realistic material models that can capture the observable behaviour of the physical system. Experiments with realistic loading rates and pressures reveal that steel and concrete display complicated nonlinear behaviour that is challenging to represent in a single constitutive model. To investigate the response of a reinforced concrete structure subjected to dynamic loads, this paper's study is based on many different material models to assess the advantages and disadvantages of the models on 2D and 3D RC walls using the LS-DYNA program. The models consisted of the KCC model and the CDP model, which represented plasticity and distinct tensile/compressive damage models, and the Winfrith model, which represented plasticity and the smeared crack model. Subsequently, the models' performances were assessed by comparing them to experimental data from reinforced concrete structures, in order to validate the accuracy of the overall behaviour prediction. The Winfrith model demonstrated satisfactory results in predicting the behaviour of 2D and 3D walls, including maximum strength, stiffness deterioration, and energy dissipation. The method accurately predicted the maximum strength of the Winfrith concrete model for the 2D wall with an error of 9.24% and for the 3D wall with errors of 3.28% in the X direction and 5.02% in the Y direction. The Winfrith model demonstrated higher precision in predicting dissipation energy for the 3D wall in both the X and Y directions, with errors of 6.84% and 6.62%, correspondingly. Additional parametric analyses were carried out to investigate structural behaviour, taking into account variables such as concrete strength, strain rate, mesh size, and the influence of the element type. [ABSTRACT FROM AUTHOR]

Given the challenges we face of an ageing infrastructure and insufficient maintenance, there is a critical shift towards preventive and predictive maintenance in construction. Self-sensing cement-based materials have drawn interest in this sector due to their high monitoring performance and durability compared to electronic sensors. While bulk applications have been well-discussed within this field, several challenges exist in their implementation for practical applications, such as poor workability and high manufacturing costs at larger volumes. This paper discusses the development of smart carbon-based cementitious coatings for strain monitoring of concrete substrates under flexural loading. This work presents a physical, electrical, and electromechanical investigation of sensing coatings with varying carbon black (CB) concentrations along with the geometric optimisation of the sensor design. The optimal strain-sensing performance, 55.5 ± 2.7, was obtained for coatings with 2 wt% of conductive filler, 3 mm thickness, and a gauge length of 60 mm. The results demonstrate the potential of applying smart coatings with carbon black addition for concrete strain monitoring. [ABSTRACT FROM AUTHOR]

The accurate and efficient inversion of permeability coefficients is significant for the scientific assessment of seepage safety in concrete face rockfill dams. In addressing the optimization challenge of permeability coefficients with few samples, multiple parameters, and strong nonlinearity, this paper proposes a novel intelligent inversion method based on the Sobol-IDBO-SVR fusion surrogate model. Firstly, the Sobol sequence sampling method is introduced to extract high-quality combined samples of permeability coefficients, and the equivalent continuum seepage model is utilized for the forward simulation to obtain the theoretical hydraulic heads at the seepage monitoring points. Subsequently, the support vector regression surrogate model is used to establish the complex mapping relationship between the permeability coefficients and hydraulic heads, and the convergence performance of the dung beetle optimization algorithm is effectively enhanced by fusing multiple strategies. On this basis, we successfully achieve the precise inversion of permeability coefficients driven by multi-intelligence technologies. The engineering application results show that the permeability coefficients determined based on the inversion of the Sobol-IDBO-SVR model can reasonably reflect the seepage characteristics of the concrete face rockfill dam. The maximum relative error between the measured and the inversion values of the hydraulic heads at each monitoring point is only 0.63%, indicating that the inversion accuracy meets the engineering requirements. The method proposed in this study may also provide a beneficial reference for similar parameter inversion problems in engineering projects such as bridges, embankments, and pumping stations. [ABSTRACT FROM AUTHOR]

The application of recycled coarse aggregate (RA) in structural concrete can save non-renewable resources and reduce land occupation. Developing comprehensive knowledge of chloride penetration and service life modeling of recycled coarse aggregate concrete (RAC) is a prerequisite for practice. However, compared with the natural aggregate concrete (NAC), the inferior durability performance, especially chloride penetration resistance, of RAC hinders its application in structural concrete. Therefore, many RAC performance enhancement methods have been proposed. This paper presents a holistic review focused on the chloride penetration of RAC with/without enhancement methods and service life prediction. The current RAC performance enhancement methods are introduced. The improvement effect of the corresponding enhancement methods on the chloride penetration resistance of RAC are discussed and analyzed in turn. Based on the reviewed data on the chloride diffusion coefficient, the modification efficiencies of assorted enhancement methods are summarized. With the hope of promoting RAC application in structural concrete, the current literature on chloride-ingress-based service life prediction for RAC is also overviewed. In addition, the typical influencing factors on chloride transport properties are also discussed, i.e., RA quality. It can be concluded that enhancement techniques can effectively improve the chloride penetration resistance of RAC. The old mortar enhancement or removal methods can improve the chloride penetration resistance by 15–30%, depending on the specific treatment measures. The modification efficiency of the modifier material depends on the specific type and content of the incorporated substance, which ranges from approximately 5% to 95%. The estimated service life of RAC structures decreases with the increasing RA replacement ratio. Finally, concluding remarks are provided concerning future research on the chloride transport behavior of RAC. [ABSTRACT FROM AUTHOR]

The effective use of waste materials is one of the key drivers in ensuring sustainability within the construction industry. This paper investigates the viability and efficacy of sustainably incorporating a polylactic acid-type plastic (WP) as a 10 mm natural coarse aggregate (NA) replacement in geopolymer concrete. Two types of concrete (ordinary Portland cement—OPC and geopolymer) were produced for completeness using a concrete formulation ratio of 1:2:3. The ordinary concrete binder control was prepared using 100% OPC at a water/binder ratio of 0.55, while the geopolymer concrete control used an optimum alkaline activator/precursor—A/P ratio (0.5) and sodium silicate to sodium hydroxide—SS/SH volume ratio (1.2/0.8). Using the same binder quantity as the control, four concrete batches were developed by replacing 10 mm NA with WP at 30 and 70 wt% for ordinary and geopolymer concrete. The mechanical performance of the developed concrete was assessed according to their appropriate standards, while a microstructural investigation was employed after 28 days of curing to identify any morphological changes and hydrated phases. The results illustrate the viability of incorporating WP in geopolymer concrete production at up to 70 wt% replacement despite some negative impacts on concrete performance. From a mechanical perspective, geopolymer concrete indicated a 46.7–58.3% strength development superiority over ordinary concrete with or without WP. The sample composition and texture quantified using automated scanning electron microscopy indicated that adding WP reduced the presence of pores within the microstructure of both concrete types. However, this was detrimental to the ordinary concrete due to the low interfacial zone (ITZ) between calcium silicate hydrate (CSH) gel and WP, resulting in the formation of cracks. [ABSTRACT FROM AUTHOR]

Thermal power plant slag is a waste that is presently obtained from many power stations all over the world. A possible method for its utilization is using it to produce concrete. This paper analyses the effect of thermal power plant slag on the technological properties of concrete mixtures and the mechanical properties of concrete subjected to heat–moisture processing. Quantitative estimates of the investigated factors' influence on the concrete mixture's water demand and the strength of steamed concrete were obtained. The influences of TPP slag content and its water demand on concrete composition features as well as concrete strength are shown. The novelty of the work lies in the use of an experimental–statistical model to optimize the composition of steamed concrete using slag from the viewpoint of maximum strength per kilogram of cement. It has been demonstrated that the optimal part of slag in aggregate, which provides maximum strength at 4 h and 28 days after steaming, is 0.5–0.55 and 0.45–0.55, respectively. A method for the design of concrete composition using slag from thermal power plants is proposed. [ABSTRACT FROM AUTHOR]

The moisture content within the concrete pore network significantly influences the mechanical, thermal, and durability characteristics of concrete structures. This paper introduces a novel fully embedded wireless temperature and relative humidity sensor connected to an automatic acquisition system designed for continuous concrete monitoring. Relative humidity measurements from this new sensor are compared with those obtained by a commercial system based on the borehole method at different depths (2.5 and 4.0 cm) and exposure conditions (oven drying and humid chamber). The results allow for proving that both systems provide consistent internal relative humidity measurements aligned with the exposure conditions and highlight the capability of fully embedded wireless sensors as a practical and reliable alternative to the conventional borehole method. Additionally, the continuous monitoring of the wireless cast-in sensor exhibits reliability during unintended temperature fluctuations, emphasizing the effectiveness of permanently installed sensors in promptly detecting unintended curing variations in real time. The continuous real-time information provided combined with the practicality of these sensors might assist construction managers to improve the quality control of the concrete curing process and shrinkage behavior, and ensure the integrity of concrete surface finishing. [ABSTRACT FROM AUTHOR]

Nowadays, the sustainable development of the construction industry has become a focus of attention. Crushing and grinding waste seashells originating from the fishery industry, such as oyster shells, cockle shells, mussel shells, and scallop shells, into different particle sizes for usage as aggregate and cement in concrete or mortar provides an effective and sustainable solution to environmental problems by reducing natural resource dependence. Numerous studies have attempted to analyze the suitability of waste seashell as a possible alternative to natural aggregates and cement in concrete or mortar. This paper presents an up-to-date review of the characteristics of different types of waste seashell, as well as the physical, mechanical, durability, and other notable functional properties of seashell concrete or mortar. From the outcome of the research, waste seashell could be an inert material, and it is important to conduct a series of proper treatment for a better-quality material. It is also seen from the results that although the mechanical properties of seashell concrete have been reduced, they all meet the required criteria set by various international standards and codes. Therefore, it is recommended that the replacement of seashells as aggregate and cement should not exceed 20% and 5%, respectively. Seashell concrete or mortar would then have sufficient workability and strength for non-structural purposes. However, there is still a lack of investigation concerning the different properties of reinforced concrete members using seashells as the replacement of aggregate or cement. Further innovative research can solidify its utilization towards sustainable development. [ABSTRACT FROM AUTHOR]

The widespread use of carpets in residential and commercial buildings and their relatively short life span result in large volumes of carpet being landfilled. A potential solution to this problem is the use of post-consumer carpet fibers in concrete. To this end, this paper systematically identifies the common fiber types in a typical post-consumer carpet fiber bale and evaluates their durability under exposure to varying levels of alkalinity. The tensile strengths and toughness of the fibers belonging to the nylon and polyethylene terephthalate (PET) families (the dominant fibers in most post-consumer carpets) are reduced by up to 50% following exposure to extreme alkalinity, the reasons for which are determined using spectroscopic and microscopic evaluations. The chloride ion transport resistance of concretes (~40 MPa strength) containing 2.5% carpet fibers by volume (~25 kg of fibers per cubic meter of concrete) is comparable to that of the control mixture, while mortar mixtures containing the same volume fraction of carpet fibers demonstrate negligible enhancement in expansion and loss of strength when exposed to 1 N NaOH. This study shows that moderate-strength concretes (~40 MPa) for conventional building and infrastructure applications can be proportioned using the chosen volume of carpet fibers without an appreciable loss of performance. Consideration of low volume fractions of carpet fibers in low-to-moderate-strength concretes thus provides a sustainable avenue for the use of these otherwise landfilled materials in construction applications. [ABSTRACT FROM AUTHOR]

During the concrete mixing process, the transition of aggregates from a dry to a moist state introduces a crucial dynamic that significantly influences particle interaction, consequently impacting mixing homogeneity. In this paper, based on the discrete element method, the effect of aggregate moisture on the mixing process of sand and stone was investigated. The interaction between dry particles was described by the Hertz–Mindlin model, while the interaction between wet particles was calculated by the linear cohesion model considering the liquid bridge force. Additionally, a functional relationship between the moisture content and the parameters of the linear cohesive contact model was established. The results show that the numerical method can be employed to simulate the mixing process. Notably, when the moisture content of pebbles ranges from 0% to 0.75% and that of sand ranges from 0% to 10.9%, the linear cohesion model is deemed suitable. The standard deviation of the mixing homogeneity of wet particles is lower than that of dry particles for short mixing time, indicating that a small amount of liquid enhances mixing homogeneity. However, moisture has no obvious effect on mixing homogeneity for a long mixing time. This nuanced understanding of the interplay between moisture, particle interactions, and mixing duration contributes valuable insights to optimize concrete mixing processes. [ABSTRACT FROM AUTHOR]

In this paper, we study spectral properties of non-self-adjoint operators with the discrete spectrum. The main challenge is to represent a complete description of belonging to the Schatten class through the properties of the Hermitian real component. The method of estimating the singular values is elaborated by virtue of the established asymptotic formulas. The latter fundamental result is advantageous since, of many theoretical statements based upon it, one of them is a concept on the root vectors series expansion, which leads to a wide spectrum of applications in the theory of evolution equations. In this regard, the evolution equations of fractional order with the sectorial operator in the term not containing the time variable are involved. The concrete well-known operators are considered and the advantage of the represented method is convexly shown. [ABSTRACT FROM AUTHOR]

This paper reports an investigation of the mechanical and microscopic properties of partially replaced banana leaf ash (BLA) concrete. In this research, the cement was partially replaced by BLA in two phases: Phase A (0%, 5%, 10%, 15%, 20%, 25% and 30%) and Phase B (0%, 10%, 20% and 30%). The consequence of partially replacing cement with BLA in concrete was investigated by the application of a range of tests, namely X-ray fluorescence (XRF), compressive strength, splitting tensile strength, flexure strength, ultrasonic pulse velocity and scanning electron microscopy (SEM) analysis. The properties were then correlated with the properties of a standard 100% Portland cement concrete of similar strength. The XRF result of the BLA identified a composition with 48.93% SiO2 and 3.48% Al2O3, which indicates that the material potentially possesses pozzolanic properties. The mechanical properties of the partially replaced BLA concrete noted minor strength loss, approximately 5% with 20% partial replacement. The nondestructive testing data showed enhanced performance up to 20% partial replacement, with ultrasonic pulse values above 3500 m/s. The scanning electron microscopy analysis illustrated that the morphology of BLA specimens contained increased microcracks compared with the control. The decrease in strength observed is attributed to the fibrous composition of the BLA. The mechanical, nondestructive testing and microscopic results highlight the potential to utilize BLA as a partial replacement for cement as a pozzolanic material in concrete at up to 20% by weight of cement. [ABSTRACT FROM AUTHOR]

Using limestone powder (LP), the by-product of manufactured sand, to replace part of fly ash (FA) or manufactured sand could not only turn waste into treasure and decrease the price of concrete, but could also enhance the performance of concrete and reduce environmental pollution. However, the impact of various LP incorporation methods on the performance of mass concrete was inconsistent. In this paper, the effects of LP on the workability, compressive strength, constrained expansion rate, hydration temperature and impermeability of mass concrete were studied by replacing FA or manufactured sand alone and replacing FA and manufactured sand simultaneously. The results showed that the impact of LP on the performance of mass concrete was equal when it replaced FA alone and FA and manufactured sand at the same time. When the replacement amount was 20%, the workability, expansibility and early strength of concrete were improved, but the later strength and impermeability were slightly reduced. The workability, compressive strength, expansibility and impermeability of mass concrete were improved when manufactured sand was replaced alone, and the optimal dosage was 10%. The LP, moreover, reduced the hydration temperature peak of concrete in three kinds of mixing methods, but the temperature peak appeared earlier. At lower dosages, LP optimized pore structure and promoted the early hydration of cement through filler effects and nucleation effects. When LP replaced manufactured sand, the microstructure of concrete was more dense, so the replacement of manufactured sand had a better effect on the improvement of concrete properties. A reference value for the use of LP in mass concrete is provided in this study. [ABSTRACT FROM AUTHOR]

This paper investigates the fracture mechanical properties of concrete, using crushed concrete aggregates (CCA) and granulated blast furnace slag (GGBS) for partial cement replacement. CCAs made from prefabricated concrete replace 100% of the fine and coarse fractions in concrete recipes with w/c ratios of 0.42 and 0.48. Two pre-treatment methods, mechanical pre-processing (MPCCA) and accelerated carbonation (CO2CCA), are investigated for quality improvements in CCA. The resulting aggregates show an increased density, contributing to an increase in the concrete's compressive strength. The novelty of this paper is the superposition of the effects of the composite parts of concrete, the aggregate and the cement mortar, and their contributions to concrete fracture. Investigations are directed toward the influence of fine aggregates on mortar samples and the influence of the combination of coarse and fine aggregates on concrete samples. The physical and mechanical properties of the aggregates are correlated with mortar and concrete fracture properties. The results show that CCA concrete achieves 70% of the fracture energy values of concrete containing natural aggregates, and this value increases to 80% for GGBS mixes. At lower w/c ratios, MPCCA and CO2CCA concretes show similar fracture energies. CO2CCA fine aggregates are the most effective at strengthening the mortar phase, showing ductile concrete behavior at a w/c ratio of 0.48. MPCCA aggregates contribute to higher compressive strengths for w/c ratios of 0.42 and 0.48. Thus, mechanical pre-processing can be improved to produce CCA, which contributes to more ductile concrete behavior. [ABSTRACT FROM AUTHOR]

The production of concrete leads to substantial carbon emissions (~8%) and includes reinforcing steel which is prone to corrosion and durability issues. Carbon-fiber-reinforced concrete is attractive for structural applications due to its light weight, high modulus, high strength, low density, and resistance to environmental degradation. Recycled/repurposed carbon fiber (rCF) is a promising alternative to traditional steel-fiber reinforcement for manufacturing lightweight and high-strength concrete. Additionally, rCF offers a sustainable, economical, and less energy-intensive solution for infrastructure applications. In this paper, structure–process–property relationships between the rheology of mix design, carbon fiber reinforcement type, thermal conductivity, and microstructural properties are investigated targeting strength and lighter weight using three types of concretes, namely, high-strength concrete, structural lightweight concrete, and ultra-lightweight concrete. The concrete mix designs were evaluated non-destructively using high-resolution X-ray computed tomography to investigate the microstructure of the voids and spatially correlate the porosity with the thermal conductivity properties and mechanical performance. Reinforced concrete structures with steel often suffer from durability issues due to corrosion. This paper presents advancements towards realizing concrete structures without steel reinforcement by providing required compression, adequate tension, flexural, and shear properties from recycled/repurposed carbon fibers and substantially reducing the carbon footprint for thermal and/or structural applications. [ABSTRACT FROM AUTHOR]

This paper deals with the effect of the character of the water used for the water storage of concrete test specimens on the results of tests for resistance to de-icing chemicals. Two experiments were conducted to investigate the effect of the content of free CO2 in water and leaching of calcium hydroxide from concrete on the test results. In the first experiment, the resistance of mortars to water and de-icing chemicals was investigated. It was found that the character of the water storage, i.e., fresh water vs. previously used water, can significantly affect the test results. The second experiment focused on investigating the effect of the content of free CO2 in water on the test results. It was found that the content of free CO2 in the water can statistically significantly influence the test results. In conclusion, the paper shows that the character of the water used for water storage of concrete test specimens and the content of free CO2 in water are essential factors that can significantly affect the results of concrete resistance tests to de-icing chemicals. Further research is needed to understand these influences and their potential use to improve the resistance of concrete. [ABSTRACT FROM AUTHOR]

Over the past 20 years, as the depth and diameter of shaft lines increased in China, the cracking and water leakage of the inner walls of frozen shafts have become increasingly severe, resulting in significant safety threats and economic losses. Understanding the stress variation patterns of cast-in-place inner walls under the combined effects of temperature and constraint during construction is a prerequisite for evaluating the crack resistance performance of inner walls and preventing water leakage in frozen shafts. The temperature stress testing machine is an important instrument for studying the early-age crack resistance performance of concrete materials under the combined effects of temperature and constraint. However, existing testing machines have shortcomings in terms of applicable specimen cross-sectional shapes, temperature control methods for concrete structures, and axial loading capacity. In this paper, a novel temperature stress testing machine suitable for the inner wall structure shape, capable of simulating the hydration heat of the inner walls, was developed. Then, a reduced-scale model of the inner wall according to similarity criteria was manufactured indoors. Finally, preliminary investigations of the temperature, strain, and stress variations of the inner wall under 100% end constraint conditions were conducted by simulating the actual hydration heating and cooling process of the inner walls. Results show that the hydration heating and cooling process of the inner wall can be accurately simulated. After approximately 69 h of concrete casting, the accumulated relative displacement and strain of the end-constrained inner wall model were −244.2 mm and 187.8 με, respectively. The end constraint force of the model increased to a maximum value of 1.7 MPa and then rapidly unloaded, causing the model concrete to crack in tension. The temperature stress testing method presented in this paper provides a reference for scientifically formulating technical approaches to prevent cracking in cast-in-place concrete inner walls. [ABSTRACT FROM AUTHOR]

Cold weather conditions pose significant challenges to the performance and durability of concrete materials, construction processes, and structures. This paper aims to provide a comprehensive overview of the material-related challenges in cold weather concrete construction, including slow setting, reduced curing rate, and slower strength development, as well as frost damage, early freezing, and freeze–thaw actions. Various innovative materials and technologies may be implemented to address these challenges, such as optimizing the concrete mix proportions, chemical admixtures, supplementary cementitious materials, and advanced construction techniques. The paper also examines the impact of weather-related challenges for personnel, equipment, and machinery in cold environments and highlights the importance of effective planning, communication, and management strategies. Results indicate that the successful implementation of appropriate strategies can mitigate the challenges, reduce construction time, and enhance the performance, durability, and sustainability of concrete structures in cold and freezing temperatures. The paper emphasizes the importance of staying updated about the latest advancements and best practices in the field. Future trends include the development of smart and functional concrete materials, advanced manufacturing and construction techniques, integrated design, and optimization of tools, all with a strong focus on sustainability and resilience. [ABSTRACT FROM AUTHOR]

The concreteness effect (CE), namely a better performance with concrete compared to abstract concepts, is a constant feature in healthy people, and it usually increases in persons with aphasia (PWA). However, a reversal of the CE has been reported in patients affected by the semantic variant of Primary Progressive Aphasia (svPPA), a neurodegenerative disease characterized by anterior temporal lobe (ATL) atrophy. The present scoping review aims at identifying the extent of evidence regarding the abstract/concrete contrast in Alzheimer's disease (AD) and svPPA and associated brain atrophy. Five online databases were searched up to January 2023 to identify papers where both concrete and abstract concepts were investigated. Thirty-one papers were selected and showed that while in patients with AD, concrete words were better processes than abstract ones, in most svPPA patients, there was a reversal of the CE, with five studies correlating the size of this effect with ATL atrophy. Furthermore, the reversal of CE was associated with category-specific impairments (living things) and with a selective deficit of social words. Future work is needed to disentangle the role of specific portions of the ATL in concept representation. [ABSTRACT FROM AUTHOR]

The movement of the construction industry towards sustainable development has drawn attention to the revision of concrete. In addition to reducing pollution, the use of nano-materials should lead to the provision of higher quality concrete in terms of regulatory items (workability, resistance characteristics, durability characteristics, microstructure). The present study investigates 15 key characteristics of concrete modified with nano-CaCO3, nano-clay, nano-TiO2, and nano-SiO2. The results of the study showed that nanomaterials significantly have a positive effect on the hydration mechanism and the production of more C-S-H gel. The evaluation of resistance characteristics also indicates the promising results of these valuable materials. The durability characteristics of nano-containing concrete showed significant improvement despite high dispersion. Concrete in coastal areas (such as bridges or platforms), concrete exposed to radiation (such as hospitals), concrete exposed to impact load (such as nuclear power plants), and concrete containing recycled aggregate (such as bricks, tiles, ceramics) can be effectively improved by using nanomaterials. It is hoped that the current review paper can provide an effective image and idea for future applied studies by other researchers. [ABSTRACT FROM AUTHOR]

Concrete structures have emerged as some of the most extensively utilized materials in the construction industry due to their inherent plasticity and high-strength characteristics. However, due to the temperature fluctuations, humidity, and damage caused by human activities, challenges such as crack propagation and structural failures pose threats to the safety of people's lives and property. Meanwhile, conventional non-destructive testing methods are limited to defect detection and lack the capability to provide real-time monitoring and evaluating of concrete structural stability. Consequently, there is a growing emphasis on the development of effective techniques for monitoring the health of concrete structures, facilitating prompt repairs and mitigation of potential instabilities. This paper comprehensively presents traditional and novel methods for concrete structural properties and damage evolution monitoring, including emission techniques, electrical resistivity monitoring, electromagnetic radiation method, piezoelectric transducers, ultrasonic techniques, and the infrared thermography approach. Moreover, the fundamental principles, advantages, limitations, similarities and differences of each monitoring technique are extensively discussed, along with future research directions. Each method has its suitable monitoring scenarios, and in practical applications, several methods are often combined to achieve better monitoring results. The outcomes of this research provide valuable technical insights for future studies and advancements in the field of concrete structural health monitoring. [ABSTRACT FROM AUTHOR]

This paper presents a ceramic stress sensor with the dimension of a coin, able to measure the compressive force (stress) applied to its two round faces. The sensor is designed and engineered to be embedded inside concrete or masonry structures, like bridges or buildings. It provides good accuracy, robustness, and simplicity of use at potentially low cost for large-scale applications in civil structures. Moreover, it can be calibrated temperature compensated, and it is inherently hermetic, ensuring the protection of sensitive elements from the external environment. It is, therefore, suitable for operating in harsh and dirty environments like civil constructions. The sensor directly measures the internal stress of the structure, exploiting the piezo resistivity of thick film ink based on ruthenium oxide. It is insensitive with respect to the stiffness of the embedding material and the variation of the surrounding material properties like concrete hardening, shrinkage, and creep as it decouples the two components of stress. [ABSTRACT FROM AUTHOR]

The mechanical properties and failure modes of concrete are controlled by its mesoscopic material composition and structure; therefore, it is necessary to study the deterioration characteristics of tunnel lining concrete under fire from a mesoscopic perspective. However, previous studies mostly analyzed the damage and failure process from a macro-homogeneous perspective, which has certain limitations. In this paper, a thermal–mechanical coupling test device was modified to simulate the state of concrete under tunnel fire conditions. Combined with CT technology, the macroscopic properties and mesoscopic characteristics of concrete were observed. Features were obtained, such as the change in compressive strength under fire, as well as mesoscopic deterioration characteristics. The damage variable D was defined to quantify mesoscopic damage, and the link between mesoscopic deterioration characteristics and macroscopic performance was established, which can be used to predict compressive strength loss through mesoscopic characteristics. [ABSTRACT FROM AUTHOR]

This paper presents the application of a hybrid approach for damage localization in concrete plates of arbitrary geometric shapes and a constant thickness. The hybrid algorithm utilizes fast discrete wavelet transformation, energy approach and time of flight criteria for the purpose of the localization of single- and multi-damage problems inside or on the periphery of concrete plates. A brief theoretical background of the hybrid method as well as numerical procedures for modeling the piezoelectric smart aggregate and ultrasonic wave propagation are presented. Experimental and numerical verification of the damage localization were performed on square samples/models with one or two damages and with 16 positions of piezoelectric smart actuator/sensor aggregates. After the verification of the hybrid method, a numerical simulation was performed on models with one or two damages for plates of arbitrary geometric shapes. Based on the obtained results, it was concluded that the proposed method can be applied to damage localization in concrete plates of arbitrary geometric shapes. The presented method and numerical procedure can be further used in research through varying the geometry, number and position of damages as well as the number and position of piezoelectric smart aggregates. [ABSTRACT FROM AUTHOR]

Recycling of multi-source solid waste is of great benefit to energy conservation and environmental governance. In this paper, a new type of environmental protection concrete for railway accessory facilities was prepared from silicon-manganese slag, steel slag, fly ash and recycled macadam. Seven kinds of concrete with different mix proportions were designed. Through unconfined compressive strength, splitting, drying shrinkage and temperature shrinkage tests, the multivariate changing trends of steel slag content, cement dosage and age on the anti-interference ability of concrete were investigated. The main mechanisms of the development of mechanical and dry shrinkage properties were revealed by the hydration process of 3SR-60. The results show that 3SR-60 had better mechanical strength under the same cement dosage. The temperature shrinkage strain decreased and then increased with the rise of the proportion of waste residue, increased with the addition of cement dosage and decreased first and then increased with the descent in the temperature. The temperature shrinkage coefficient reached the lowest value at 0–10 °C. The drying shrinkage coefficient decreases with the increase in the proportion of waste residue and increases with the increase in cement dosage. The dry shrinkage strain increased rapidly during the first 8 days and became almost constant after 30 days. Cementation of calcium silicate hydrate (C-S-H) and ettringite (AFt) developed continuously and filled the internal pores of the structure, interlocking and cementing with each other, which made the microstructure develop from a three-dimensional network to a dense complex, and the macro dimension was reflected in the enhancement of the power to resist external interference. The conclusion of the test summarized that SR-60 had preferable mechanical and shrinkage performance. [ABSTRACT FROM AUTHOR]

This paper presents and investigates the properties of concrete in which a portion of the cement is substituted with non-sintered Hwangto (NSH), a readily available building material in Asia. Given the inactive nature of NSH, this study aimed to determine the optimal cement replacement ratio and quantitative strength of the material. The unit weight, compressive strength, ultrasonic pulse velocity (UPV), and stress–strain of the NSH concrete (NSHC) were evaluated. Additionally, we developed a predictive model for determining compressive strength based on the regression analysis of compressive strength and UPV. The water-to-binder ratio was set to 0.41, 0.33, and 0.28, and the NSH replacement rates in the cement were set to 0%, 15%, 30%, and 45% for evaluating various strength ranges. The mechanical property measurements indicated reductions of 5.35% in unit weight, 35.62% in compressive strength, and 6.34% in UPV as the NSH was replaced. Notably, the smallest deviation from plain concrete was observed at a replacement rate of 15%. The scanning electron microscopy analysis results showed that the plain concrete exhibited a crystalloid structure; however, as the NSH replacement rate increased, the amorphous structure and pores increased while unreacted NSH particles were also observed. The X-ray diffraction analysis results demonstrate that the peak intensities for kaolinite and mullite increased as the NSH replacement rate increased, while those of C–S–H gel and CaO showed low peak intensities. Furthermore, the regression analysis concluded that an exponential function was suitable. Consequently, a compressive strength prediction model was developed, and in the error test, the NSHC model demonstrated an average error of <10%, with fewer errors at the lower compressive strength boundaries. [ABSTRACT FROM AUTHOR]

The causes of cracks in concrete are varied, and regardless of their origin, these cracks invariably have a detrimental impact on the durability of concrete structures and escalate their maintenance costs. This paper presents a comprehensive review of current knowledge regarding the methods of self-healing in concrete, ranging from autogenic and improved autogenic self-healing to the autonomous self-healing of concrete. Particular emphasis is placed on the methods of autonomous concrete self-healing: the bacterial healing method, the crystalline hydrophilic additives healing method, and the capsule-based self-healing method. The hypothesis is that applying these self-healing methods could potentially prevent damages or cracks in concrete caused by freeze–thaw cycles, thereby extending the lifespan of concrete structures. The mechanism of action and current achievements in the field are provided for each method. [ABSTRACT FROM AUTHOR]

In this paper, firstly, the effects of graphene oxide on the mechanical properties of concrete were investigated. Secondly, the degradation and mechanism of the mechanical properties of graphene oxide concrete (GOC) under sulfate attack and a freeze–thaw environment were investigated. In addition, the dynamic modulus of elasticity (MOEdy) and uniaxial compressive strength (UCS) of the GOC were measured under different environmental conditions. According to the test results, the incorporation of graphene oxide in appropriate admixtures could improve the mechanical properties of concrete in these two working environments. It is worth noting that this effect is most pronounced when 0.05 wt% graphene oxide is incorporated. In the sulfate attack environment, the MOEdy and UTS of the GOC0.05% specimen at 120 cycles decreased by 22.28% and 24.23%, respectively, compared with the normal concrete specimens. In the freeze–thaw environment, the MOEdy and UTS of the GOC0.05% specimen at 90 cycles decreased by 13.96% and 7.58%, respectively, compared with the normal concrete specimens. The scanning electron microscope (SEM) analysis showed that graphene oxide could adjust the aggregation state of cement hydration products and its own reaction with some cement hydration crystals to form strong covalent bonds, thereby improving and enhancing the microstructure density. [ABSTRACT FROM AUTHOR]

The goal of this paper is to investigate the impact of nano-materials on the mechanical and electrochemical properties of self-cleaning concrete. Nano-titanium dioxide and nano-zinc oxide were used as additives for this purpose. Additionally, a comparative study on the effect of using these materials on the self-cleaning concrete's characteristics was conducted. The dosages of nano-titanium dioxide (nps-TiO2) and nano-zinc oxide (nps-ZnO) used were 0, 0.5, 1, 1.5, 2, and 2.5% and 0, 1, 2, and 3% of the weight of the cement, respectively. The results showed that the optimum compressive strength and the lowest corrosion rate were fulfilled at 2.5% of nps-TiO2 and 1% of nps-ZnO, and using 2.5% of nps-TiO2 achieved the highest improvement in the corrosion rate. However, 1% for nps-TiO2 mixtures and 1% for nps-ZnO mixtures were the best ratios for flexural strength. On the other hand, for the corrosion rate, the samples were tested at 2 and 6 months. When nps-TiO2 and nps-ZnO samples were compared to the control sample, 2.5% and 1% of nps-TiO2 and nps-ZnO, respectively, showed the largest improvement in resistance to corrosion. Also, the self-cleaning property of the samples containing nano-materials (nps-TiO2 and nps-ZnO) was tested. As the results illustrated, the self-cleaning property of the samples was increased over time due to photocatalytic degradation. Furthermore, the results of the photocatalytic tests showed that nps-TiO2 samples outperformed nps-ZnO samples overall. [ABSTRACT FROM AUTHOR]

This paper presents experimental results on the influence of concrete composition factors on the criterion characterizing the ratio between the compressive strength of activated low-cement concrete and clinker consumption. The investigation was carried out using mathematical planning of the experiments. Experimental and statistical models describing the influence of the fly ash, activating additive (microsilica), consumption of cement and aggregates, as well as the superplasticizer on the strength of low-cement concrete under normal hardening conditions and after steaming were obtained. The values of the clinker efficiency criterion and the mineral additive cementing efficiency coefficient were calculated, and models of these parameters were obtained for the investigated concrete compositions. It was shown that the activating effect of microsilica yields an increase in ash cementing efficiency and clinker efficiency criterion in concrete. Using the obtained models, an example for calculating the ash cementing efficiency coefficient is given. [ABSTRACT FROM AUTHOR]

In this paper, we introduce a method for simulating the deformation of concrete surfaces due to weathering employing an example-based approach to replicate shape changes observed in real-world objects. A key challenge in implementing this approach is the scarcity of opportunities to measure shapes both before and after the weathering process. To overcome this limitation, we utilize concrete bricks collected from real-world environments as standardized examples, allowing for an analysis of erosion. By measuring erosion based on the estimated original shape, we correlate the characteristics of erosion with geometric features such as curvature and accessibility. We then apply this analysis to simulate new weathering effects in a given input model in alignment with its own geometric features. Our method yields visually compelling results while reproducing the variation of geometric weathering effects. [ABSTRACT FROM AUTHOR]

Modern infrastructure heavily relies on robust concrete structures, underscoring the critical need for effective monitoring to ensure their safety and durability. This paper addresses this imperative issue by introducing an innovative automated and wireless system for continuous structural monitoring. By employing embedded electrical resistivity sensors coupled with a wireless-based data transmission mechanism, real-time data collection becomes feasible. We provide a general description of the system's architecture and its application in a pilot study covering the effects of the devices on concrete properties and data transmission. The dielectric properties of concrete specimens were investigated under natural and accelerated curing/degradation and the results were used in the final design of the antenna device. Furthermore, a pilot test comprising four reinforced concrete columns was used to investigate the range of data transmission from inside to outside of the concrete, the effects of the hardware device on the compressive strength and concrete distribution in the columns, and the data transmission quality in real time under realistic exposure conditions. [ABSTRACT FROM AUTHOR]

Light-transmitting concrete as a building material already exists in many forms, but its light properties and the possibilities of using it to improve the lighting of interior spaces have not been investigated in detail yet. This paper focuses on the illumination of interior spaces using constructions made of light-transmitting concrete, which will allow light to pass between individual spaces. The experimental measurements carried out are divided into two typical situations using reduced room models. The first part of the paper focuses on the illumination of the room through the penetration of daylight through the ceiling made of light-transmitting concrete. The second part of the paper investigates the transmission of artificial light from one room to another through a non-load-bearing dividing structure composed of unified slabs of light-transmitting concrete. For the experiments, several models and samples were created for comparison. The first step of the experiment was to create slabs of light-transmitting concrete. While there are many options to produce such a slab, the best option is to use high-performance concrete with glass-fiber reinforcement, which improves the load transfer properties, and plastic optical fibers for light transmission. By adding optical fibers, we can achieve the transmission of light between any two spaces. For both of the experiments, we used reduced-scale models of rooms. Slabs with dimensions of 250 × 250 × 20 mm and 250 × 250 × 30 mm were used in three versions: concrete slabs with optical fibers, concrete slabs with air holes and solid slabs. The experiment measured and compared the level of illumination at several points in the model as it passed through each of the three different slabs. Based on the results of these experiments, it was concluded that the interior level of illumination of any space can be improved by using light-transmitting concrete, especially those without access to natural light. The experiment also assessed the strength properties of the slabs in relation to their intended use and compares them with the properties of stone slabs used as cladding. [ABSTRACT FROM AUTHOR]