Search

A number of models for the critical surface of Nb3 Sn, and in general A15 superconductors, have been developed in the past years. This paper compares the most common parameterizations using consistent notation. Although the parameterizations appear dissimilar at first sight, they are in reality all based on a fit of the normalized pinning force vs. the reduced field, and have similar scalings for the critical field and critical temperature based on a Unified Scaling Law. In this paper we take the various parameterizations as a basis for a generic scaling proposed for the characterization and production follow-up of the ITER Nb3 Sn strands. The accuracy of the scaling is estimated using the fitting residuals on various sets of Ic (B, T, ϵ) data available in literature. We discuss the results, and give our view of the work towards a unified, practical parameterization. [ABSTRACT FROM AUTHOR]

Abstract: In this paper, a complete framework including modeling, identification and control design for an experimental Helium refrigerator facility submitted to high pulsed loads is proposed. Such high pulsed loads are expected to take place in future Tokamaks such as the International Thermonuclear Experimental Reactor (ITER) or the Japan Torus-60 Super Advanced (JT60SA). The control architecture is split into two loops: The first concerns the warm compression system while the second manages the remaining part of the refrigerator (often called the cold box) in which the set-points of the first loop are viewed as manipulated variables. The efficiency of the proposed solution is experimentally assessed under several scenarios including those involving realistic high pulsed loads. [Copyright &y& Elsevier]

Abstract: In the ITER edge Thomson scattering measurement system, polychromators with optical band-pass filters and avalanche photodiodes are planned to be used. In this paper, we optimized the transmission wavelength ranges of the optical filters by a numerical method. Since measurements in a high electron temperature range are required for the measurement system, the Thomson spectrum could overlap a strong line emission of when the electron temperature is rather high. It is shown that a filter whose transmission wavelength range is shorter than becomes important to decrease the measurement error in the high temperature range. Moreover, it is found that a filter whose transmission wavelength range is above 1064nm (laser wavelength) is useful to improve the measurement accuracy, in particular, when the number of filters is more than six. [Copyright &y& Elsevier]

Abstract: The present paper deals with the detailed investigation of the helium-cooled lithium lead test blanket module (HCLL-TBM) nuclear behaviour under irradiation in ITER, carried out at the Department of Nuclear Engineering of the University of Palermo adopting a numerical approach based on the Monte Carlo method. A realistic 3D heterogeneous model of the HCLL-TBM was set-up and inserted into an ITER 3D semi-heterogeneous model that realistically simulates the reactor lay-out up to the cryostat. A Gaussian-shaped neutron source was adopted for the calculations. The main features of the HCLL-TBM nuclear response were assessed, paying a particular attention to the neutronic and photonic deposited power, the tritium production rate and the spatial distribution of their volumetric densities. Structural material irradiation damage was also investigated through the evaluation of displacement per atom and helium and hydrogen production rates. [Copyright &y& Elsevier]

Abstract: The ITER conductor is made of a superconductor cable with multi-stage twisted strands. The spatial structure of such a cable is essential for understanding the effect of load and strain on the performance of a superconducting cable. Unfortunately, there have no analytical models so far to describe accurately such twisted spatial structure. This paper proposes a twisting matrix model to accurately describe the spatial structure of a multi-stage twisted superconducting cable. Although the current model only simulates the first step of a cabling process, it still gives approximately neighboring relation between strands and sub-cables. This neighboring relation is essential for any cabling simulation. The 2nd step simulation, i.e., compaction, can be realized by finite element method based on the cable spatial structure constructed by the proposed one. The simulation results by this model agree well with the observations for pitch and orientation. [Copyright &y& Elsevier]

Abstract: The operating limits and conditions (OLCs) are operating parameters and conditions, chosen among all system/components, which, together, define the domain of the safe operation of ITER in all foreseen ITER states (operation, maintenance, commissioning). At the same time they are selected to guarantee the required operation flexibility which is a critical factor for the success of an experimental machine such as ITER. System and components that are important for personnel or public safety (safety important class, SIC) are identified considering their functional importance in the overall plant safety analysis. SIC classification has to be presented already in the preliminary safety analysis report and approved by the licensing authority before manufacturing and construction. OLCs comprise the safety limits that, if exceeded, could result in a potential safety hazard, the relevant settings that determine the intervention of SIC systems, and the operational limits on equipment which warn against or stop a functional deviation from a planned operational status that could challenge equipment and functions. Some operational conditions, e.g. in-Vacuum Vessel (VV) radioactive inventories, will be controlled through procedures. Operating experience from present tokamaks, in particular JET, and from nuclear plants, is considered to the maximum possible extent. This paper presents the guidelines for the development of the ITER OLCs with particular reference to safety limits. [Copyright &y& Elsevier]

In this paper we report the main test results obtained on the Poloidal Field Conductor Insert coil (PFI) for the International Thermonuclear Experimental Reactor (ITER), built jointly by the EU and RF ITER parties, recently installed and tested in the CS Model Coil facility, at JAEA-Naka. During the test we (a) verified the DC and AC operating margin of the NbTi Cable-in-Conduit Conductor in conditions representative of the operation of the ITER PF coils, (b) measured the intermediate conductor joint resistance, margin and loss, and (c) measured the AC loss of the conductor and its changes once subjected to a significant number of Lorentz force cycles. We compare the results obtained to expectations from strand and cable characterization, which were studied extensively earlier. We finally discuss the implications for the ITER PF system. [ABSTRACT FROM AUTHOR]

The measurement of the current sharing temperature of a Cable in Conduit Conductor is a complex task. The voltage traces measured on the conduit (jacket) of these conductors during tests, give V∙I characteristics that significantly differ from the typical transition from the superconducting to the resistive state measured on single strands. In these measurements, after an initial ramping of the transport current up to the test value, the temperature is increased by steps until the resistive transition occurs. However, even in the first phase of the current ramping, when the cable is still fully or almost superconductive, early voltages are measured along the jacket at different angular positions around the cable. In particular, this was observed in the ITER TF conductors recently tested in the SULTAN facility at Villigen PSI, Switzerland. These samples showed significant ramps of voltages taken in the proximity of the joints and terminations. The present paper gives a possible qualitative and quantitative explanation for this mechanism. Numerical simulations are also shown which reproduce the scattering of the voltages measured around the jacket at a given location, showing the effect of the voltage taps position along the jacket in a six sub-cable model. [ABSTRACT FROM AUTHOR]

For the superconducting magnet system of the International Thermonuclear Experimental Reactor, ITER, 60 current leads for a total current of more than 2500 kA are needed. The use of High Temperature Superconductor current leads (HTS-CL) will reduce the resultant large refrigerator load considerably. Within the EU Fusion Technology Programme, the Forschungszentrum Karlsruhe and CRPP have developed and built a 70 kA HTS-CL demonstrator optimized for 50 K Helium operation. In 2004-2005, the CL was successfully tested with 50 K as well as 80 K Helium, and finally with LN2. In the meantime, ITER has decided to use HTS-CLs for the magnet system and China has taken the responsibility to provide the sc feeders for ITER including the current leads. In this paper, the performance of a 70 kA HTS-CL in fault conditions will be analysed using the FZK-CRPP demonstrator as a model. In particular, the quench performance and the safety behavior in case of a loss-of-flow accident (LOFA) will be described and an extrapolation of the leads performance in real ITER conditions will be given. Finally the effect of different shunt materials is discussed. [ABSTRACT FROM AUTHOR]

The ITER Organization (10) and the Institute of Plasma Physics at the Chinese Academy of Sciences (ASIPP) are jointly developing the 68 kA current leads using High Temperature Superconductors for the superconducting Toroidal Field (TF) magnet system of the International Thermonuclear Experimental Reactor, ITER. The proposed design consists of a conventional helium cooled heat exchanger operating between 65 K and 320 K and an HTS module covering the low temperature end using Bi-2223 tapes. The first HTS current lead prototypes will be tested in the EAST tokamak facility at ASIPP. This paper discusses the design of the first, 68 kA, TF HTS lead, which is the main emphasis of this first stage of the ITER current lead development program. [ABSTRACT FROM AUTHOR]

Dust mobilization in a vacuum vessel is one of the key issues endangering the security of the International Thermonuclear Experimental Reactor (ITER) in case of loss of vacuum accidents. The turbulent behavior of particles in turbulent flows has to be modeled for successful numerical simulations about particle mobilization. In this study a Lagrangian approach is adopted to formulate the particle transport especially for dust-dilute flows mostly encountered in the vacuum vessel of ITER. Based on the logic frame of the approach and the used computational fluid dynamics (CFD) computer code in the study, a hybrid turbulent particle dispersion model is proposed. The hybrid model features both a deterministic separated flow model and a stochastic separated flow (SSF) model, which are two popular turbulent dispersion models applied in particle simulations, and takes the advantages of the both models. The proposed model is implemented into the particle model of the CFD code successfully and the simulation results are verified against the experimental data. The verifications manifest the validities of the proposed model. In this paper general information about the work of dust mobilization is introduced and the particle turbulent dispersion models are reviewed briefly at first. The hybrid model is then proposed based on the SSF model. An experiment about particle dispersions in an advective wind channel flow with decaying turbulence in the streamwise direction is reviewed in the third section. In the following section about model verification, the decaying turbulence parameters in the channel flow are verified against the experimental data as the first step, and the parameters about the particle dispersions in the verified flow field are then verified against the data. The work is concluded finally. [ABSTRACT FROM AUTHOR]

The US is proposing a prototype of a dual coolant liquid lead-lithium DEMO blanket concept for testing in the International Thermonuclear Experimental Reactor (ITER) as an ITER test blanket module (TBM). Because safety considerations are an integral part of the design process to ensure that this TBM does not adversely impact the safety of ITER, a safety assessment has been conducted for this TBM and its ancillary systems as requested by the ITER project. Four events were selected by the ITER international team (IT) to address specific reactor safety concerns, such as vaccum vessel (VV) pressurization, confinement building pressure build-up, TBM decay heat removal capability, tritium and activation products release from the TBM system and hydrogen and heat production from chemical reactions. This paper summarizes the results of this safety assessment conducted with the MELCOR computer code. [ABSTRACT FROM AUTHOR]

For the superconducting magnet system of the International Thermonuclear Experimental Reactor, ITER, 60 current leads for a total current of more than 2500 kA are needed. To reduce the resultant large refrigerator load at 4.5 K, High Temperature Superconductor current leads (HTS-CL) could be used. Therefore, EFDA CSU Garching had launched a development program for a 70 kA HTS-CL demonstrator. The Forschungszentrum Karlsruhe and CRPP developed and built this CL optimized for 50 K Helium operation. In 2004, the CL was successfully tested in the TOSKA facility at the Forschungszentrum Karlsruhe. The very encouraging results lead to testing this CL with 80 K Helium because ITER provides a large 80 K Helium cooling capacity for the thermal shields. At the end of last year, the test could be successfully performed demonstrating that high current capacity current leads can be stably operated at about 80–85 K. Recently, the CL was retested using liquid nitrogen which would be an interesting alternative option. In this paper, the test results for the 80 K He cooling operation as well as for the operation with LN2 are presented and compared to the results obtained before for nominal conditions. [ABSTRACT FROM AUTHOR]

Three planned test blanket modules (TBMs) and 18 toroidal field coils break the axisymmetry of the ITER magnetic field. In this paper, the plasma response on these non-axisymmetric fields is studied quantitatively. For this purpose, self-consistent, three-dimensional, free-boundary equilibria of type ITER scenario 4 are computed. The resulting 3D equilibrium magnetic fields are then compared with the corresponding axisymmetric fields to which the vacuum perturbation fields are superimposed. The studies are performed for various normalized plasma pressures. [ABSTRACT FROM AUTHOR]

Presents an abstract for a paper describing the preliminary operational plan and physics program for the International Thermonuclear Experimental Reactor (ITER) in La Jolla, California, and its implications for plasma measurements. Key objectives of the first ten years of ITER.