Search

Recently, as the use of wearable devices and the demand for eco-friendly energy have increased, many studies have been conducted on triboelectric nanogenerators (TENGs), which can economically harvest energy. Paper is considered a promising substrate and frame material that can be used to manufacture self-powered TENGs, owing to its flexibility, low cost, and accessibility. Herein, we present a sandwich-structured foldable paper-based TENG (FP-TENG) that comprises flexible materials and uses paper as a substrate. The FP-TENG can generate up to 572 mW/m2 of power via contact–separation of the triboelectric electrified body at the top and bottom. With more folds of the FP-TENG, the triboelectric cross-sectional area increases, and, thus, the electrical output increases. In addition, the proposed TENG exhibits excellent durability without signal degradation under 5000 cycles of repeated pushing motions. To demonstrate its practicality, the FP-TENG was manufactured in the form of a wristwatch Velcro and connected to an electronic watch panel to supply power. Various deformations are possible with origami, and they can drive wristwatches through external forces. Therefore, the FP-TENG is expected to be utilized as a sustainable and promising eco-friendly energy source for small electronic devices. [ABSTRACT FROM AUTHOR]

In this framework, experimental tests on different battery technologies, BMS and cooling systems are extremely important to extend the battery life and BEV performance (Sehil et al. [[13]]). Electrical machines and magnetic components, high-voltage voltage power converters, and battery storage systems are some basic bricks to build an effective and efficient energy conversion environment. Electrical Machines and Power Converters The electrical power conversion from renewable energy sources plays a crucial role in the development of a sustainable society. Finally, the fil rouge of every contribution in this section is oriented to investigate the power converters, electrical machines, magnetic components, and battery storage systems in actual energy conversion applications for renewable energy sources integration by a modelling approach. [Extracted from the article]

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed motor-driven fixed-displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. The simulation results demonstrate four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation. [ABSTRACT FROM AUTHOR]

In this paper, the notion of a cohesive and self-sufficient grid is proposed. Based on a cohesive and self-sufficient virtual microgrid, an active distribution network is optimally planned, and an optimal configuration of demand-side resources, distributed generations, and energy storage systems are generated. To cope with stochastic uncertainty from forecast error in wind speed and load, flexibility reserves are needed. In this paper, the supply relation between flexibility and uncertainty is quantified and integrated in an innovative index which is defined as cohesion. The optimization objectives are a minimized operational cost and system net-ability cohesion as well as self-sufficiency, which is defined as the abilities both to supply local load and to deal with potential uncertainty. After testing the optimal configuration in the PG&E 69 bus system, it is found that with a more cohesive VM partition, the self-sufficiency of VMs is also increased. Also, a case study on uncertainty-caused system imbalance is carried out to show how flexibility resources are utilized in real-time operational balance. [ABSTRACT FROM AUTHOR]

The research problem of this paper is related to numerous open questions in the field of energy, its understanding, its use, and the challenges of the energy future. After the introductory part, in which a brief historical overview of energy literacy is provided, the paper focuses on energy literacy, its emergence, and the different approaches to its definition and measurement. The paper analyzes the energy literacy of students at the Faculty of Economics in Rijeka based on their cognitive, affective, and behavioral skills. Their knowledge about energy, energy processes, and the energy efficiency of the objects they encounter on a daily basis is examined. Their personal attitudes and values are examined through various forms of personal initiatives and active participation in energy sustainability projects. Finally, the habits and behavioral patterns that the respondents have in their daily lives and their tendencies to save energy resources and find energy-efficient solutions are examined. Despite some positive findings, the current results are not satisfactory and point to the creation of adequate public policies with a particular focus on education and the role of the corrective mechanisms of the state, but also the need for joint negotiations between policy makers, regulators, scientists, representatives of civil society, and the business community. The particular contribution of this work is reflected in being the first research of its kind conducted among Croatian economics students, as well as among Croatian students in general; in the creation of a research instrument that is conceptually consistent with the findings from the existing literature, but with an original set of questions within each energy literacy skill adapted to the cultural and sociological background of the respondents; and in a kind of progress from previous research by taking into account the quantitative aspect (in addition to the qualitative) assessment of the respondents' energy literacy. [ABSTRACT FROM AUTHOR]

Due to a rising share of renewable energy sources on the production side and electrification of transport and heating on the consumption side, the efficient management of flexibility in distribution networks is crucial for ensuring optimal operation and utilization of resources. Nowadays, the sensitivity-based approach is mainly used in medium-voltage (MV) networks for regulating voltage profiles with reactive power of distributed energy resources (DER). The main disadvantage of the simplified sensitivity-based method is its inaccuracy in case of a high deviation of the network voltage from the nominal values. Furthermore, it was also noted that despite the fact that the method is well described in the literature, there is a lack of systematic approach to its implementation in real-life applications. Thus, the main objective of this paper is to address this disadvantage and to propose an algorithm designed to calculate required consumer flexibility in near real-time to ensure distribution grid operation within operational criteria. In the first part of the paper, network state, including line loading and node voltages, is assessed to determine distribution network node capacity. By analyzing the sensitivity of network busbars to changes in consumption and production, our algorithm effectively identifies the most efficient nodes and facilitates strategic decision-making for resource allocation. We demonstrate the effectiveness of our approach through simulations of real-world distribution network data, highlighting its ability to enhance network flexibility and improve resource utilization. Leveraging sensitivity coefficients, the algorithm enables flexible consumption and production management across various scenarios, supporting the transition to a more dynamic and efficient power system. [ABSTRACT FROM AUTHOR]

Recently, there has been a significant increase in the integration of distributed energy resources (DERs) such as small-scale photovoltaic systems and wind turbines in power distribution systems. When the aggregated outputs of DERs are combined, excessive reverse current may occur in distribution lines, leading to overvoltage issues and exceeding thermal limits of the distribution lines. To address these issues, it is necessary to limit the output of DERs to a certain level, which results in constraining the hosting capacity of DERs in the distribution system. In this paper, coordination control methodologies of DERs are developed and executed to mitigate the overvoltage and overcurrent induced by DERs, thereby increasing the hosting capacity for DERs of the distribution system. This paper proposes three coordinated approaches of active and reactive power control of DERs, namely Var Precedence, Watt Precedence, and Integrated Watt and Var Control. The Var and Watt Precedence prioritizes reactive power for voltage (Q–V) and active power for current (P–I) to address network congestion, thereby enhancing hosting capacity. Conversely, the Integrated Var and Watt Precedence propose a novel algorithm that combines four control indices (Q–V, P–V, Q–I, and P–I) to solve network problems while maximizing hosting capacity. The three proposed methods are based on the sensitivity analysis of voltage and current to the active and reactive power outputs at the DER installation locations on the distribution lines, aiming to minimize DER active power curtailment. Each sensitivity is derived from linearized power equations at the operating points of the distribution system. To minimize the computation burden of iterative computation, each proposed method decouples active and reactive power and proceeds with sequential control in its own unique way, iteratively determining the precise output control of distributed power sources to reduce linearization errors. The three proposed algorithms are verified via case studies, evaluating their performance compared to conventional approaches. The case studies exhibit superior control effectiveness of the proposed DER power control methods compared to conventional methods when issues such as overvoltage and overcurrent occur simultaneously in the distribution line so that the DER hosting capacity of the system can be improved. [ABSTRACT FROM AUTHOR]

Low or even zero carbon dioxide emissions will be an essential requirement for energy supplies in the near future. Besides transport and electricity generation, industry is another large carbon emitter. Hydrogen produced by renewable energy provides a flexible way of utilizing that energy. Hydrogen, as an energy carrier, could be stored in a large capacity compared to electricity. In Sweden, hydrogen will be used to replace coal for steel production. This paper discusses how the need for electricity to produce hydrogen will affect the electricity supply and power flow in the Swedish power grid, and whether it will result in increased emissions in other regions. Data of the Swedish system will be used to study the feasibility of implementing the hydrogen system from the power system viewpoint, and discuss the electricity price and emission issues caused by the hydrogen production in different scenarios. This paper concludes that the Swedish power grid is feasible for accommodating the additional electricity capacity requirement of producing green hydrogen for the steel industry. The obtained results could be references for decision makers, investors, and power system operators. [ABSTRACT FROM AUTHOR]

Ever-increasing penetration of distributed energy resources (DERs) in the power grids, alongside their numerous benefits, brings new challenges that call for enhanced solutions in the field of control and management of power grids. The majority of the available research have considered either distribution or transmission grids in their studies. In this paper, a comprehensive review of the effects of DERs on the distribution and transmission grids is performed. The focus of this paper is on hierarchical management methods in order to categorize different approaches and highlight the gaps. Moreover, a review is conducted in the field of the newly introduced distributed energy resources management system (DERMS) concept. A DERMS can facilitate the hierarchical energy management procedure due to its functionalities and broad capabilities. Hence, its implementation in energy management and its impact on the power grid will be assessed with the aid of a co-simulation platform that considers both transmission and distribution grids. [ABSTRACT FROM AUTHOR]

This paper presents a preliminary study of a 25 kV–50 Hz railway substation power supply system. The control of a back-to-back converter based on modular multilevel converter (MMC) technology was investigated to fit with the power quality requirements of the application. One of the main challenges is the presence of constraining load conditions, under which the train circulation variability, low-frequency harmonics and critical power transients can notably decrease the power quality and lead to instability. In order to address this, cascaded controllers based on resonant controllers are proposed to ensure the desired performance. Furthermore, balancing voltage algorithms are added to avoid stress phenomena and additional losses in the studied power conversion interface. The paper presents the design of the control stages and demonstrates the robust performance of the system using a realistic loading condition of a railway substation. [ABSTRACT FROM AUTHOR]

The application of electrochemical cells as a source unit of electrical energy is rapidly growing—used in electric vehicles and other electric mobility devices, as well as in energy supply systems—as energy storage, often together with renewable energy sources. The key element of such systems is the power electronic converter used for DC energy storage and AC grid interfacing. It should be bidirectional to charge and discharge the battery when it is necessary. Two-stage battery interface converters are the most common; their DC-DC stage controls the battery current and adjusts voltage, but the DC-AC stage (inverter or frontend) controls the current in the grid. The use of unfolding inverters in two-stage battery interfaces can have some advantages. In this case, the DC-DC converter produces half-sinewave pulsating voltages and currents, but the unfolding circuit changes the polarity of the voltages and currents and produces no switching losses. Another trend of modern power electronics is the principle of partial power processing. In this case, power electronic converters deal only with a part of the total power; therefore, losses in such converters are reduced. This paper considers combining unfolding frontends with partial power DC-DC converters that enable the further reduction in losses. In this paper, it is shown that such implementation of the partial power conversion principle in semi-DC-AC systems is really possible based on the real-time matching of the voltage of the partial-power DC-DC converter, battery voltage (which depends on its state of charge) and the rectified instantaneous voltage of the AC grid. [ABSTRACT FROM AUTHOR]

The expansion of distributed renewable resources, together with increased demand from the electrification of transport and heating sectors, impacts distribution networks significantly. Additionally, the emergence of non-programmable and intermittent generators is set to diminish the dominance of traditional rotating and programmable generation, thereby affecting the overall stability of the system. Nevertheless, the flexibility offered by distributed resources has the potential to alleviate the necessity for network reinforcement and contribute to system stability at competitive costs. Local flexibility procurement should be rooted in local markets, serving as mechanisms to address distribution congestion and coordinate the provision of flexibility for transmission network services. The multitude of existing systems and the interdependence of flexibility services have given rise to diverse solutions, still undergoing experimentation in various countries. This paper aims to scrutinize key projects that have established local flexibility markets, delineating their fundamental characteristics, the most common solutions, identifying prevalent barriers and suggesting potential future improvements. The investigation focuses on the most uncertain aspects of local markets: possible TSO-DSO coordination schemes, the time horizon for the acquisition of services and the baseline definition methodologies. [ABSTRACT FROM AUTHOR]

The current development of prosumer microsources and the expected spread of electric vehicles may cause the appearance of significant current and voltage unbalance in low-voltage (LV) networks. This unbalance, which is an unfavorable phenomenon, may occur when using single-phase photovoltaic (PV) microsources and single-phase home chargers for electric vehicles. This paper presents a proposal for the symmetrization of the LV network using devices for the reconfiguration of phases in the power supply. Both the different locations of these devices and the different objective functions for device implementation are analyzed. The research was carried out on an example LV network, taking into account several variants of the development of PV microsources and home chargers for electric vehicles. The analysis indicates that the appropriate location of phase reconfiguration devices and the use of an appropriate objective function leads to a significant reduction in unfavorable unbalancing in the LV network. [ABSTRACT FROM AUTHOR]

This paper introduces a Fuzzy Logic Controller designed for an on-load tap changer within medium voltage distribution systems with bulk penetration of Distributed Energy Resources. As the on-load tap changer remains one of the most essential forms of voltage regulation in medium voltage distribution networks, improving its operation is a cost-effective response to the emerging voltage violations caused by intermittent generation during the early stages of the energy system transformation. Software-in-the-loop simulations were conducted to validate the effectiveness of the proposed algorithm compared to the conventional methods. A modified CIGRE Medium Voltage Distribution Network Benchmark in European Configuration was modelled while the controller code developed in Python 3.12 was running on a PC, both coupled in a real-time closed-loop environment. The analyses showed that the proposed algorithm managed to reduce overvoltage from 7.02% to 4.85% in the benchmark network, thus demonstrating that the algorithm is efficient and ready for on-field implementation. [ABSTRACT FROM AUTHOR]

An efficient and reliable management system for a cluster of distributed energy resources (DERs) is essential for the sustainable and cost-effective peak management (PM) operation of the power grid. The virtual power plant (VPP) provides an efficient way to manage a variety of DERs for the PM process. This paper proposes a VPP framework for PM of local distribution companies by optimizing the self-scheduling of available resources, considering uncertainties and constraints. The study examines two separate scenarios and introduces novel algorithms for determining threshold values in each scenario. An approach is suggested for the transaction between VPP and the aggregator models. The proposed technique intends to determine the optimal amount of capacity that aggregators can allocate for the day-ahead PM procedure while accounting for both thermostatically controlled and non-thermostatically controlled loads. The proposed VPP framework shows promising results for reducing demand charges and optimizing energy resources for PM. [ABSTRACT FROM AUTHOR]

It is widely recognised that improving the visibility and controllability of distributed energy resources (DERs) within electricity distribution networks will have significant benefits, particularly for the management of low-voltage (LV) and medium-voltage (MV) networks. Much work within the electricity distribution industry is currently focused on improving the visibility of DERs on LV networks. From a control-theoretic perspective, this enables closing the loop between the DER and the control room and enables a shift towards utilising data-driven model-based control strategies for DERs. The result is a system-wide performance that is closer to the theoretical optimal. In the Australian context, several jurisdictions are trialling techniques such as dynamic operating envelopes to enhance DER hosting capacity, using IEEE 2030.5-based architectures, with the implementation of distributed energy resource management (DERMS) systems at the enterprise level still quite limited. While there is significant activity focused on DER behaviour and control techniques by way of inverter grid codes and standards, the core issue of interoperability with distribution management systems (DMSs), market operators or participants, electric vehicles (EVs) or other DERs is still a work in progress. Importantly, this is also an impediment to realising distributed architectures for DER control in the grid. The unique characteristics of Australian distribution networks highlights several challenging problems for DER control and management. The objective of this paper is to provide a broad overview of DER control and management strategies in the Australian context, with an application focus on DER control in distribution network management. [ABSTRACT FROM AUTHOR]

Behind the meter (BTM) distributed energy resources (DERs), such as photovoltaic (PV) systems, battery energy storage systems (BESSs), and electric vehicle (EV) charging infrastructures, have experienced significant growth in residential locations. Accurate load forecasting is crucial for the efficient operation and management of these resources. This paper presents a comprehensive survey of the state-of-the-art technologies and models employed in the load forecasting process of BTM DERs in recent years. The review covers a wide range of models, from traditional approaches to machine learning (ML) algorithms, discussing their applicability. A rigorous validation process is essential to ensure the model's precision and reliability. Cross-validation techniques can be utilized to reduce overfitting risks, while using multiple evaluation metrics offers a comprehensive assessment of the model's predictive capabilities. Comparing the model's predictions with real-world data helps identify areas for improvement and further refinement. Additionally, the U.S. Energy Information Administration (EIA) has recently announced its plan to collect electricity consumption data from identified U.S.-based crypto mining companies, which can exhibit abnormal energy consumption patterns due to rapid fluctuations. Hence, some real-world case studies have been presented that focus on irregular energy consumption patterns in residential buildings equipped with BTM DERs. These abnormal activities underscore the importance of implementing robust anomaly detection techniques to identify and address such deviations from typical energy usage profiles. Thus, our proposed framework, presented in residential buildings equipped with BTM DERs, considering smart meters (SMs). Finally, a thorough exploration of potential challenges and emerging models based on artificial intelligence (AI) and large language models (LLMs) is suggested as a promising approach. [ABSTRACT FROM AUTHOR]

The increasing level of harmonics in the power grid, driven by a substantial presence of coupled inverter-based energy resources (IBRs), poses a new challenge to power grid transient stability. This paper presents the findings from experiments and analytical studies on the impact of the topological configuration of coupled IBRs on the level of power flow harmonics in a distribution grid: (i) our findings report that the impact of grid topology on harmonics is nonlinear, which is in contrast to the common perception that the power grid operates as a large linear low-pass filter for harmonics; (ii) importantly, this study highlights that the influence of the topological configuration of inverters on the reduction of system-level harmonics is more substantial than the effect of line impedance, emphasizing the significance of grid topological configuration; (iii) furthermore, the observed reduction in harmonics is attributed to a harmonic cancellation effect achieved through self-compensation by all the coupled inverters without affecting the active power flow in the power grid. These findings propose a new approach to limit the penetration of complex IBR harmonics in the power grid from a system-wide perspective. This approach significantly differs from the component-level or localized solutions used today, such as inverter control, power filtering, and transformer tap changes. [ABSTRACT FROM AUTHOR]

This paper analyzes the behavior of an electrical power system when N-1 contingencies occur in the transmission stage, which can be produced by incorrect operation of the protection relays, phenomena of natural origin, or increased loadability, which affect the operation and reliability of the electrical system. The operation output of a transmission line results in the variation of the nominal values of the electrical parameters involved because they disturb the stability of the generation, transmission systems, and the supply of electrical energy to the loads, such as voltages and angles of the nodes and the active and reactive power of the system. The proposed methodology was based on analyzing the different electrical parameters of the power system, quantifying the contingency index in a state of regular operation, and comparing it to operation in contingency N-1, with which the most severe contingency was determined and, therefore, achieved; identifying contingencies that can cause system collapses; improving the contingency index from 23.08555 to 22.9276624 for the L16–19 contingency and to 22.9795235 for the L21–22 contingency, which are the most severe contingencies determined with the proposed methodology. To test the proposed methodology, the IEEE 39 bus-bar test system was considered, and the elements that should be implemented to avoid the vulnerability of the power system to N-1 contingencies were determined. [ABSTRACT FROM AUTHOR]

Distributed Energies Resources (DERs) can be controlled for supporting the voltage regulation at nodes of an Active Distribution Network (ADN) where they are connected. However, since the ADN is a Multi-Input Multi-Output (MIMO) system with coupled dynamics, the controller of a DER mutually interacts with all other controllers through the distribution lines. These interactions lead to operating conflicts which may drive the ADN to work close to its voltage stability boundaries. To achieve a stable voltage regulation without new investment in the existing ADNs, the present paper proposes a straightforward decentralized design of the multi-loop controllers based on the property of integral controllability. The main feature of the method is that the design problem can be expressed by a single parameter designed both for reducing the effects of the undesired coupling and for increasing the degree of robust stability in the presence of parameter uncertainty in the matrix plant. Simulation studies are developed to illustrate the design result and the performance achieved under different operating conditions. The performance is also compared with the one obtained by another method in terms of the integral absolute error. [ABSTRACT FROM AUTHOR]

Energy markets are crucial for integrating Distributed Energy Resources (DER) into modern power grids. However, this integration presents challenges due to the inherent variability and decentralized nature of DERs, as well as poorly adapted regulatory environments. This paper proposes a medium-term decision-making approach based on a comprehensive suite of computational tools for integrating DERs into Colombian energy markets. The proposed framework consists of modular tools that are aligned with the operation of a Commercial Virtual Power Plant (CVPP). The tools aim to optimize participation in bilateral contracts and short-term energy markets. They use forecasting, uncertainty management, and decision-making modules to create an optimal portfolio of DER assets. The suite's effectiveness and applicability are demonstrated and analyzed through its implementation with heterogeneous DER assets across various operational scenarios. [ABSTRACT FROM AUTHOR]

The DC distribution network is a low-inertia system, which is very sensitive to load disturbance, system failure, and other factors. By adding virtual capacitance to the converter connected to the power supply, the virtual inertia of the DC power grid can be improved. Firstly, this paper proposes a strategy for adjusting virtual capacitance based on the voltage change rate to achieve adaptive control of virtual inertia, which enables the converter to quickly absorb or release energy during power fluctuations. Secondly, the adaptivity of the strategy is improved and the main control parameters in the proposed control method are qualitatively analyzed. Finally, the four-terminal photovoltaic storage DC distribution network system is constructed. Through Simulink, the adaptive virtual inertia control is incorporated on the battery side to simulate and validate the effectiveness of the strategy and the rationality of parameter analysis. The results show that this method can provide flexible and adjustable inertia support for DC grids and improve the voltage stability of DC grids. [ABSTRACT FROM AUTHOR]

With the urgent global need to limit warming to 2 °C as well as a localized need in our case study to address rising energy demand amid electrical and thermal network limitations, a critical examination of demand-side energy reductions and the concept of energy sufficiency is needed. This paper contributes to the sparse literature on bottom-up analysis by utilizing Iceland—a leader in renewable energy generation—as a case study to explore the socio-economic factors influencing energy footprints. Our findings reveal significant energy footprints across various consumption domains, particularly housing and mobility, influenced by income levels, urbanization, and lifestyle choices. The study highlights the paradox of a high renewable energy supply leading to potential misconceptions regarding abundant and low-cost energy, resulting in substantial energy consumption-related environmental impacts. Using detailed household consumption survey data, this research provides insights crucial for developing sustainable energy policies that not only target technological advancements but also address the need for a reduction in energy demand and a shift towards energy sufficiency. This work marks a contribution to the literature through the provision of a case study of low income inequality and high energy footprints in a highly renewable energy system context. Further, this work is useful for Icelandic and international policymakers to understand in such high-demand contexts which consumption domains would be most relevant for sufficiency policies. This comprehensive analysis opens pathways for future research to further explore the intersections of energy consumption, socio-economic factors, and well-being, offering a nuanced understanding necessary for crafting sufficiency and demand-side policies aimed at a sustainable energy future. [ABSTRACT FROM AUTHOR]

Global warming increases the risk of power outages. Mine water pumping stations pump approximately 100 million m3 of water per year (2023). The cessation of mine water pumping would expose neighboring mines and lower lying areas to flooding. The pumping stations have some containment, but a prolonged shutdown could cause environmental problems. Remediation of the resulting damage would be costly and time-consuming. The combination of the problems of dewatering abandoned mines and storing energy in the form of hydrogen to ensure continuity of power supply to pumping stations has not been the subject of extensive scientific research. The purpose of this paper was to develop options for protecting mine water pumping stations against the "blackout" phenomenon and to assess their investment relevance. Six technically feasible options for the modernization of mine water pumping stations were designed and analyzed in the study. All pumping station modernization options include storage of the generated energy in the form of green hydrogen. For Q1 2024 conditions, the option with the partial retail sale of the produced hydrogen and the increased volume of produced water for treatment is recommended for implementation. [ABSTRACT FROM AUTHOR]

Solar energy is one type of clean energy resource, and currently the IMO, EU and UK are targeting net zero carbon emissions by 2050. This paper delves into the integration of photovoltaic (PV) systems into hybrid vessels in order to meet their strategies and targets. The technical challenges that come with designing such systems as well as their economic and environmental impacts are examined. By optimizing the usage of harnessed solar energy, we discover the operational strategy that provides maximal benefits through day-to-day savings as well as over the 25 year lifespan of solar panels. It demonstrates impressive economic viability, with cost savings of up to GBP 4.55 per day and a payoff period as short as 9 years. It also displays a modest emission reduction of up to 8.002 kg of CO2, which serves as proof for a pathway to greener practices in the maritime industry. This report highlights the operational flexibility that a hybrid vessel possesses once paired with a PV system through the ability to withstand regulatory and market changes. Also, when looking ahead, further adoption of PV technology creates opportunities for innovation in adopting renewable energy solutions in maritime transportation. [ABSTRACT FROM AUTHOR]

Microgrids (MGs) have evolved as critical components of modern energy distribution networks, providing increased dependability, efficiency, and sustainability. Effective control strategies are essential for optimizing MG operation and maintaining stability in the face of changing environmental and load conditions. Traditional rule-based control systems are extensively used due to their interpretability and simplicity. However, these strategies frequently lack the flexibility for complex and changing system dynamics. This paper provides a novel method called hybrid intelligent control for adaptive MG that integrates basic rule-based control and deep learning techniques, including gated recurrent units (GRUs), basic recurrent neural networks (RNNs), and long short-term memory (LSTM). The main target of this hybrid approach is to improve MG management performance by combining the strengths of basic rule-based systems and deep learning techniques. These deep learning techniques readily enhance and adapt control decisions based on historical data and domain-specific rules, leading to increasing system efficiency, stability, and resilience in adaptive MG. Our results show that the proposed method optimizes MG operation, especially under demanding conditions such as variable renewable energy supply and unanticipated load fluctuations. This study investigates special RNN architectures and hyperparameter optimization techniques with the aim of predicting power consumption and generation within the adaptive MG system. Our promising results show the highest-performing models indicating high accuracy and efficiency in power prediction. The finest-performing model accomplishes an R 2 value close to 1, representing a strong correlation between predicted and actual power values. Specifically, the best model achieved an R 2 value of 0.999809, an MSE of 0.000002, and an MAE of 0.000831. [ABSTRACT FROM AUTHOR]

As offline control photovoltaic (PV) plants are not equipped with online communication and remote control systems, they cannot adjust their power in real-time. Therefore, in a distribution network saturated with offline control PVs, the distribution system operator (DSO) should schedule the distributed energy resources (DERs) considering the uncertainty of renewable energy to prevent curtailment due to overvoltage. This paper presents a day-ahead network operation strategy using a mobile energy storage system (MESS) and offline control PVs to minimize power curtailment. The MESS model efficiently considers the transportation time and power loss of the MESS, and models various operating modes, such as the charging, discharging, idle, and moving modes. The optimization problem is formulated based on mixed-integer linear programming (MILP) considering the spatial and temporal operation constraints of MESSs and is performed using chanced constrained optimal power flow (CC-OPF). The upper limits for offline control PVs are set based on the probabilistic approach, thus mitigating overvoltage due to forecasting errors. The proposed operation strategy was tested in the IEEE 33-node distribution system coupled with a 15-node transportation system. The test results show the effectiveness of the proposed method for minimizing curtailment in offline control PVs. [ABSTRACT FROM AUTHOR]

A reasonable allocation of production schedules and savings in overall electricity costs are crucial for large manufacturing conglomerates. In this study, we develop an optimization model of off-site industrial production scheduling to address the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's power supply, and the difficulty in promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and variations in electricity prices in different places to optimize the scheduling of industrial production in various locations. The model is embedded with two sub-models, i.e., an electricity price prediction model and a distributed photovoltaic power cost model to complete the model parameters, in which the electricity price prediction model utilizes a Long Short-Term Memory (LSTM) neural network. Then, the particle swarm optimization algorithm is used to solve the optimization model. Finally, the production data of two off-site pharmaceutical factories belonging to the same large group of enterprises are substituted into the model for example analysis, and it is concluded that the optimization model can significantly reduce the electricity consumption costs of the enterprises by about 7.9%. This verifies the effectiveness of the optimization model established in this paper in reducing the cost of electricity consumption on the demand side. [ABSTRACT FROM AUTHOR]

Natural gas hydrate (NGH) is a potential future energy resource. More than 90% of NGH resources exist in the pore medium of seafloor sediments. During the development of deep-sea oil and gas fields, wellbore pipelines are often clogged due to the synthesis of gas hydrates, and the addition of thermodynamic inhibitors is a common solution to prevent hydrate synthesis. In this paper, the effects of two single inhibitors, sodium chloride and ethylene glycol, as well as hybrid inhibitors combining these two inhibitors on the synthesis of methane hydrates were investigated using the self-developed one-dimensional gas hydrate exploitation simulation test apparatus. The effects of single and hybrid inhibitors were investigated in terms of the hydrate synthesis volume and gas–water two-phase conversion rate. The results show that the hybrid inhibitor has a better inhibitory effect on hydrate synthesis with the same initial synthesis driving force. When the concentration of inhibitors is low, salt inhibitors can have a better inhibitory effect than alcohol inhibitors. However, in the mixed inhibitor experiment, increasing the proportion of ethylene glycol in the mixed inhibitor can more effectively inhibit the synthesis of hydrates than increasing the proportion of sodium chloride in the mixed inhibitor. [ABSTRACT FROM AUTHOR]

The use of renewable energy sources to achieve carbon neutrality is increasing. However, the uncertainty and volatility of renewable resources are causing problems in power systems. Flexible and low-carbon resources such as Energy Storage Systems (ESSs) are essential for solving the problems of power systems and achieving greenhouse gas reduction goals. However, ESSs are not being installed because of Korea's fuel-based electricity market. To address this issue, this paper presents a method for determining the optimal investment timing of Battery Energy Storage Systems (BESSs) using the Least Squares Monte Carlo (LSMC) method. A case study is conducted considering the System Marginal Price (SMP) and Capacity Payment (CP), which are electricity rates in Korea. Revenue is calculated through the arbitrage of a 10 MW/40 MWh lithium-ion BESS, and linear programming optimization is performed for ESS scheduling to maximize revenue. The ESS revenue with uncertainty is modeled as a stochastic process using Geometric Brownian Motion (GBM), and the optimal time to invest in an ESS is determined using an LSMC simulation considering investment costs. The proposed method can be used as a decision-making tool for ESS investors to provide information on facility investments in arbitrage situations. [ABSTRACT FROM AUTHOR]

Active Distribution Networks are Multi-Input Multi-Output (MIMO) systems with coupled dynamics, which cause interactions among the control loops of Distributed Energy Resources (DERs). This undesired effect leads to performance degradation of voltage control. To mitigate the effects of this unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In detail, each DER is equipped with a double-loop PI to control the active and reactive power output of the voltage source converter, which connects the DER to the network's node. Furthermore, to guarantee ancillary services, the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a procedure with two sequential steps based on the Internal Model Control (IMC) technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in the presence of model parameter uncertainty in the MIMO plant, modeling various operating conditions of the ADN, including a step connection of large loads, renewable energy source variations, and changes in the substation transformer ratio. [ABSTRACT FROM AUTHOR]

With the continuous development of large-scale wind and photovoltaic power worldwide, the net load fluctuation of systems is increasing, thereby imposing higher demands for power supply assurance and new energy consumption capacity within emerging power systems. It is imperative to establish a quantifiable and efficient model for planning new power systems, to propose an analytical approach for determining optimal evolutionary paths, and to advance research on flexible resource planning across wide areas. In this paper, based on the simplified operating characteristics of multi-type flexible resources, a source-grid-load-storage collaborative planning and evolution analysis framework is established. Secondly, the lowest total cost of the whole life cycle of the system is taken as the optimization goal, the multiple flexible resource investment decisions and production operation constraints of various flexible resources on all sides of the system are considered, and the source-grid-load-storage planning model is established. Then, through the investment decision-making strategy setting of the system in different planning level years, the evolutionary path analysis method of the whole life cycle economy and weighted environmental protection benefit of the system is given. Finally, by taking the sending-end power grid in Gansu Province as an example, a case study is carried out. Calculations of new energy, key channels within the province, energy storage capacity, and load-side response capacity requirements for 2025, 2030, and 2060 are optimized. Based on the above analysis, the optimal evolution path of the power grid is proposed. When considering the weighted benefits of economy and environmental protection, the greater the weight of environmental protection benefits, the greater the possibility of choosing a radical scheme. The model and method proposed in this paper can provide technical reference for the future development planning and evolution analysis of new power systems. [ABSTRACT FROM AUTHOR]

The modern world is moving towards a zero-emission economy; therefore, various actions are being taken to reduce the share of fossil fuels in energy production. The article examines the potential for the continued expansion of photovoltaic farms, with a special emphasis on farms utilising east–west panel orientation. The east–west orientation is an innovative solution with many advantages over the traditional north–south arrangement. The paper also makes a detailed assessment of the photovoltaic farm environment by applying two analyses based on the following factors: Political, Economic, Social, and Technological (PEST) and Demographic, Economic, Environmental, Political, Legal, Informational, Social, and Technological (DEEPLIST) factors. This is followed by an insightful, comprehensive review of the most important factors that contribute to the efficiency of photovoltaic installations, namely site conditions, existing infrastructure, and ability to connect to the electricity grid. The paper also devotes space to an analysis of daily energy price changes that affect the economic efficiency of the installation and discusses the potential for energy storage in the context of photovoltaic farms. The development of photovoltaics also requires investing in energy storage. All discussed issues fall within the scope of photovoltaic farm development and optimal use of energy resources. [ABSTRACT FROM AUTHOR]

Increasing energy security is a crucial component of achieving the Sustainable Development Goals (SDGs). Three main factors influence energy security: (1) the efficiency of resource use in energy production, (2) the extent of energy losses, and (3) the use of new energy sources. Novel food products can impact these factors, and this paper explores whether they are being studied in the context of reducing energy consumption. Specifically, we investigate the role of technical progress and know-how in the creation and development of novel food products and whether novel methods of food production using artificial intelligence aim to reduce energy expenditures while improving product quality, variety, and the use of new energy sources. This paper seeks to examine the impact determinants of novel foods on energy security, considering economic, technological, social, and environmental aspects of knowledge about new food. To implement the study, the relevant international literature published in the past ten years have been reviewed and methods of modeling, visualization, and descriptive statistics applied. The review is structured into three sections: the first section presents ways to save energy and other resources in the food production chain through the intensive use of artificial intelligence tools; the second section presents the development of novel food products; and the last section presents marketing challenges for novel foods. The findings show that the topic addressed by this paper is currently critical, with many authorities, research centers, food producers, and energy producers interested. However, the research problem remains open, as a systematic review of secondary sources revealed little knowledge of the topic under study, and each author's study presents a new solution. The conclusion is that utilizing new foods and innovative production techniques that require less energy not only enhances production diversity but also improves its quality. [ABSTRACT FROM AUTHOR]

As the main source of energy supply and carbon emissions, the oil and gas industry has entered the comprehensive low-carbon transition stage driven by various factors. Since different oil companies possess distinct understandings of transition paths, the effect of low carbon transition varies greatly. Obviously, it is necessary to evaluate the performance of low-carbon transitions within the oil and gas industry. Therefore, in this paper, 10 major international oil companies are taken as examples, and a super-efficiency slack-based measurement (super-SBM) model is applied in the present study to analyze the efficiency of low-carbon transitions. Furthermore, the logarithmic mean Divisia index (LMDI) is used to decompose the driving factors of carbon emissions and analyze their impact on the low-carbon transition of international oil companies. The obtained results reveal that although major oil companies have taken different measures in low-carbon transition and achieved a year-on-year reduction in carbon emissions, from the perspective of the efficiency of the entire production and operation process, these oil companies are inefficient in carbon emissions and need to adopt more effective low-carbon transition strategies; Moreover, after the further decomposition of the carbon emission driving factors of the 10 companies, it is found that improving the energy consumption intensity and development level of oil companies can effectively improve the effect of low-carbon transition of international oil companies. Drawing on the above findings, this paper puts forward suggestions for the low-carbon transition of energy companies, thus providing theoretical support and guidance for energy companies in different countries to implement low-carbon transition and green development strategies. [ABSTRACT FROM AUTHOR]

The synthesis of methane from hydrogen and carbon dioxide creates an energy resource that is suitable for long-term storage. Once this process is powered by renewable electricity, it produces a clean fuel for producing electricity and heat and supports large-scale renewable energy deployment, energy transition and climate change mitigation. This paper proposes a pragmatic approach to assessing the economic potential of synthetic methane-based power. Today, natural gas plays an important role in the Baltic region due to the existing infrastructure, which includes a transmission and distribution pipeline network, gas power plants and a large underground storage reservoir. Replacing natural gas with synthetic methane would fulfil carbon emission reduction ambitions. In this paper, we simulate electricity producers' actions at market conditions and consider the generation portfolio in the Baltics and the interconnections with Scandinavia and Poland operating in the NORDPOOL electricity market. As a result of these calculations, we obtain the volume of the synthetic gas, the production costs, the volume of gas storage, the installed capacity of the gas power plant, and the investments required to ensure energy transition and system adequacy. These results are essential for the informed decisions made by policymakers, investors and system operators. [ABSTRACT FROM AUTHOR]

Recently, the generalization of P2P (peer-to-peer) technology with enhanced security due to blockchain technology and the expansion of renewable energy-based distributed energy resources have led to blockchain technology being applied in power transactions, thus giving the potential to become a new platform for DC microgrid operation. Meanwhile, the voltage of a DC microgrid represents the balance of energy supply and demand and also serves as a stability index. The balance is represented as a steady state; the stability is represented during and after events. This paper examines the stability of the DC microgrid built on a university campus in Korea and, in particular, the blockchain technology-based power transactions performed in the DC microgrid. The test is based on the pre-planned transaction schedule applied in the DC microgrid. The transaction schedule has used day-ahead and real-time bidding data. Although many technologies are included in the project, this paper focuses on the voltage stability of the DC microgrid. In addition, the DC protection is applied and evaluated. To consider general DC protection, the DC breaker was simplified with several IGBTs, diodes, capacitors, and arrestors and was designed to interrupt the fault current within five milliseconds. The stability was evaluated using a PSCAD/EMTDCTM. [ABSTRACT FROM AUTHOR]

This paper takes a cursory look at the problem of inadequate power supply in the rural healthcare centres of a developing country, specifically Nigeria, and proffers strategies to address this issue through the design of hybrid renewable energy systems combined with the existing unreliable grid in order to meet the healthcare load demand, thus ensuring higher reliability of available energy sources. The simulations, analysis and results presented in this paper are based on meteorological data and the load profiles of six selected locations in Nigeria, using which hybrid grid-connected systems integrating diesel, solar and wind energy sources are designed with configurations to give optimum output. The optimised design configurations in the considered case study, Ejioku, Okuru-Ama, Damare-Polo, Agbalaenyi, Kadassaka and Doso, produce very low energy costs of of 0.0791 $/kWh, 0.115 $/kWh, 0.0874 $/kWh, 0.0754 $/kWh, 0.0667 $/kWh and 0.0588 $/kWh, respectively, leveraging solar and wind energy sources which make higher percentage contributions at all sites. The load-following-dispatch strategy is adopted at all sites, ensuring that at every point in time, there is sufficient power to meet the needs of the healthcare centres. Further works on this topic could consider other strategies to optimise general energy usage on the demand side. [ABSTRACT FROM AUTHOR]

In this paper, a two-leg-transfer switch structure method that can continuously supply three-phase power even when an accident occurs in a power semiconductor of a three-level active neutral-point-clamped (ANPC) inverter for railway vehicles is presented. The proposed method can minimize the ripple effect caused by power semiconductor faults by separating the faulty leg from the main circuit and connecting the load-side circuit to a neutral point. As a result of simulations, the average values of MAE and RMSE can be reduced by 1.53 [A] and 1.77 [A], respectively, when using the proposed leg-transfer switch structure compared to using the conventional structure. In the IGBT failure experiment, when the proposed method was applied to a three-level ANPC inverter, there was only a 0.21 [%] difference from the THD under normal conditions. As a result, the magnitude, phase, and total harmonic distortion of the three-phase current waveforms measured before and after the fault were identical. Thus, normal three-phase power could be effectively supplied to the load when the proposed leg-transfer switch method was applied after a power semiconductor fault occurred in the three-level ANPC inverter. If this leg-transfer switch method is applied in three-level ANPC inverterd for railway vehicles, track schedule errors can be minimized by continuously supplying three-phase power to the electric motor even when an accident occurs in a power semiconductor. [ABSTRACT FROM AUTHOR]

A grid blackout is an intractable problem with serious economic consequences in many developing countries. Although it has been proven that microgrids (MGs) are capable of solving this problem, the uncertainties regarding when and for how long blackouts occur lead to extreme difficulties in the design and operation of the related MGs. This paper addresses the optimal design problem of the MGs considering the uncertainties of the blackout starting time and duration utilizing the kernel density estimator method. Additionally, uncertainties in solar irradiance and ambient temperature are also considered. For that, chance-constrained optimization is employed to design residential and industrial PV-based MGs. The proposed approach aims to minimize the expected value of the levelized cost of energy ( L C O E ), where the restriction of the annual total loss of power supply ( T L P S ) is addressed as a chance constraint. The results show that blackout uncertainties have a considerable effect on calculating the size of the MG's components, especially the battery bank size. Additionally, it is proven that considering the uncertainties of the input parameters leads to an accurate estimation for the LCOE and increases the MG reliability level. [ABSTRACT FROM AUTHOR]

Frequency response performance in power systems is becoming vulnerable due to the transition toward the higher penetration of renewable energy such as achieving carbon neutrality. In particular, reducing power system inertia energy as the asynchronous generation increases could result in violating the frequency stability constraint when a disturbance occurs in the power systems. In order to control the rapidly fluctuating frequency of the power system with low inertia, it is necessary to introduce fast frequency response resources such as a Battery Energy Storage System (BESS). This paper proposes a method to calculate the required capacity of BESS for compensating the frequency control performance of the power system using inertia energy. For calculating the required capacity of BESS, the inertia energy in the critical power system, where frequency control performance marginally satisfies frequency stability constraint, should be calculated. Also, the inertia energy in the evaluated power system having deficit inertia energy should be calculated. By comparing power systems that respond with different dynamics when the same disturbance occurs, the proposed calculation corresponds to the ratio of inertia energy deficiency based on critical power system inertia energy within the power imbalance. Through various case studies employing Korean power systems, the effectiveness of the inertia energy-based calculation method for the required BESS is verified by the fact that the BESS integrated power system marginally satisfies the frequency stability constraint. In these study cases, it is found that the instant response of BESS is very effective for compensating the frequency control performance of the low inertia power system. By applying the proposed method, it is also found that about 840 MW of BESS can achieve carbon neutrality in the Korean power system. [ABSTRACT FROM AUTHOR]

With the large-scale use of wind turbines, the ability of the power system to resist frequency fluctuations has been greatly weakened, making the contradiction between frequency regulation supply and demand in the power system increasingly prominent. In order to ensure the frequency security of the power system, this paper conducts research on the primary frequency regulation (PR) backup configuration problem of a power system containing a high proportion of wind power. First, according to the dynamic properties of the speed regulator, a system frequency response model considering the limiting link is established. And the system frequency response model is transformed into a time-domain analytical function of PR reserve capacity and frequency maximum value. On this basis, a PR backup configuration model of a power system containing a high proportion of wind power is constructed with the optimization goal of minimizing system operating costs and taking into account the limiting link constraints. It is proposed to use the L-shape algorithm to decompose the model into main problems and sub-problems, which effectively reduces the solution complexity of the model. Finally, the correctness and effectiveness of this model are verified based on the improved IEEE 39-bus system. [ABSTRACT FROM AUTHOR]

Geothermal energy exploration, development, and research have been ongoing in Canada for several decades. The country's cold climate and the push to develop renewable energy sources have driven interest in geothermal energy. Despite this drive, regulatory complexities and competition with other relatively inexpensive energy sources with existing infrastructure have hindered development. As such, interest has grown and waned with changes in the energy economy over several decades, leaving many projects at a standstill. As of January 2023, there are currently no operational geothermal power projects in Canada. Many hot spring pool and spa complexes remain active, and Canada is a leading country in the installation of ground source heat pumps (GSHPs; also called geo-exchange systems). However, in the last decade, the interest in deep geothermal systems has renewed, with many new projects starting up across several provinces and territories. Moreover, projects that had shown limited progress for many years—such as Mount Meager in British Columbia—have begun to renew their development efforts. Research is also expanding within prominent research groups and universities. The areas of focus include both building upon previous studies (such as thermal gradients and the heat flow in sedimentary basins) and researching new methods and resources (such as GSHPs, closed-loop systems, integrated geothermal operations, and hybrid systems, including heat storage). The development is supported by federal, provincial, and territorial governments through grants and the development of regulatory frameworks. Although challenges still remain for Canada to develop its geothermal energy resources, several power, thermal, and co-production projects, ongoing research, funding, and regulatory acts are all moving forward to support geothermal development. This paper aims to study Canada's geothermal energy update in 2023 regarding the aspects mentioned above. [ABSTRACT FROM AUTHOR]

In order to achieve the flexible and efficient utilization of distributed energy resources, microgrids (MGs) can enhance the self-healing capability of distribution systems. Conventional primary droop control in microgrids exhibits deviations in voltage and frequency and lacks research on voltage–frequency control during network reconfiguration. Therefore, this paper investigates the control strategy of secondary control for voltage and frequency during the process of reconstructing distribution networks to operate in the form of microgrids after faults. Firstly, the mathematical model of three-phase voltage-source inverters with droop control is analyzed. Then, inspired by the generator's secondary frequency control strategy, an improved secondary control method based on droop control is proposed, and the effectiveness of the improved droop control strategy is verified. Finally, simulation examples of distribution networks with various dynamic boundary topology changes are designed to simulate a relatively stable control result, validating the proposed strategy. [ABSTRACT FROM AUTHOR]

The basic requirements for the design of a switchgear for main 35–220 kV step-down substations are reliability and efficiency. Switchgear circuits are chosen depending on the number of supply and transit lines and transformers, the substation's place in the power supply system, and the area that can be allocated under the substation construction. The substation switchgear's reliability depends on the circuit type and the equipment to be installed. When designing, as a rule, standard substation switchgear circuit solutions are chosen with often unreasonably overstated reliability indicators and, as a consequence, capital costs. This paper explores the issues of automated choice of the best option for the 35–220 kV substation switchgear circuit, considering its structural reliability and additional costs for the area allocated under the electrical unit. A distinctive feature of the work is a comprehensive accounting of the reliability indicators of the substation and the influence of the layout of switchgear circuits as a whole on the performance indicators of future electrical installations. The developed technique is used at the pre-design stages and allows for reducing further capital, maintenance, and repair costs for electrical units by up to 14.5%. The developed approach is implemented in the original TER CAD software product. [ABSTRACT FROM AUTHOR]

Integration of inverter-based distributed energy resources (DERs) is reshaping the landscape of distribution grids to fulfill the socioeconomic, environmental, and sustainability goals. Addressing the technological challenges of DER grid integration requires an adaptive communication layer for efficient DER management and control. This transition has given rise to a cyberphysical system (CPS) architecture within the distribution system, causing new vulnerabilities for cyberphysical attacks. To better address potential threats, this paper presents a comprehensive risk assessment framework for cyberphysical security in distribution grids with grid-edge DERs. The framework incorporates a detailed CPS model accounting for dynamic DER characteristics within the distribution grid. It identifies vulnerabilities in DER communication systems, models attack scenarios, and addresses communication latency crucial for inverter control timescales. Subsequently, the quantification of attack impacts employs an attack probability model including both the vulnerability and criticality of cyber components. The proposed risk assessment framework was validated through testing on the modified IEEE 13-node and 123-node test feeders. [ABSTRACT FROM AUTHOR]

PV power generation is developing fast in both centralized and distributed forms under the background of constructing a new power system with high penetration of renewable sources. However, the control performance and stability of the PV system is seriously affected by the interaction between PV internal control loops and the external power grid. The impact of the PV system on the reliability, stability, and power quality of power systems has restricted them to further participate in power supplies with a large capacity. Traditional control methods have become ineffective at dealing with these problems as the PV system becomes increasingly complex and nonlinear. Intelligent control as a more advanced technology has been integrated into the PV system to improve system control performance and stability. However, intelligent control for the PV system is still in the early stages due to the extensive calculation and intricate implementation of intelligent algorithms. Further investigations should be carried out to effectively combine intelligent control with the PV system to constitute an intelligent PV power system with multiple functions, high stability, and high-performance. This paper provides a systematic classification and detailed introduction of various intelligent optimization methods in a PV inverter system based on the traditional structure and typical control. The future trends and research topics are given to provide a reference for the intelligent optimization control in the PV system. [ABSTRACT FROM AUTHOR]

The energy transition introduces new technical standards, laws and regulations regarding the stability and reliability of energy grids and systems. Due to the non-existence of a measuring standard, key performance indicators (KPIs) were developed to enable the measurement and comparison of individual energy grid (namely electricity, heat and gas grid) and system supportabilities while also promoting well-founded decision-making and optimization efforts. Inconsistencies in definitions concerning fundamental energy terms and the correlations between them inhibit the effective usage of the KPIs. Therefore, the overarching issue of the security of energy supply and its related subjects were also approached. The primary subject of this paper is the development of two new KPIs to measure and compare the energy grid and system supportability. These KPIs are based on spatio-temporal conditions in their respective grids. The usage and benefits of the developed KPIs are exemplarily highlighted by analyzing the impact of a scenario with the integration of a large-scale heat pump into the electricity and heat grid. The energy grid supportability is determined for each grid, whereas the energy system supportability takes the interactions of the electricity and heat grid into account. The developed KPIs are intended to enable stakeholders to identify areas with optimization potential in energy grids and systems. Moreover, the KPIs can be used to create a standardized evaluation method for regulatory requirements. [ABSTRACT FROM AUTHOR]

The demand for the power grid system's capacity to undergo peak-shaving is increasing as the proportion of renewable energy rises. In China, nuclear power units usually only provide a base load operation in the view of safety and economic considerations, but they do not provide load adjustment services, which undoubtedly increases the pressure of grid load adjustment. In this paper, a novel flexibility load adjustment strategy of the CHP nuclear unit is studied, which is achieved by introducing the thermal storage tank (TST) into the Rankine cycle without changing the output of the nuclear reactor. The AP1000 pressurized water reactor nuclear power unit for combined heat and power is taken as an example, and the thermodynamic model is established through the water vapor equation. Furthermore, the reference system is simulated for the goal of minimizing the imbalance between power supply and demand, and the flexibility–environment–economy benefits are evaluated. The results show that the heat storage/release of the TST may achieve power output flexible adjustment of the nuclear unit, and the power imbalance of the reference energy system is reduced from 1107.99 MWh to 457.24 MWh, a reduction of 58.73%. The introduction of a 600 MWh TST can enable the reference unit to contribute 335 MWh of peak electricity within the reference day. From the perspective of replacing the power generation output increment of coal-fired power units with equal amounts, it can achieve a reduction of 106.09 tons of coal consumption in the case day, which means that 277.73 tons of CO2 emissions can be reduced. The profit of the reference unit can be improved by CHY 70,125 via participating in load adjustment in the case day if following the time-of-use electricity price. [ABSTRACT FROM AUTHOR]

The efficient integration of distributed energy resources (DERs) in buildings is a challenge that can be addressed through the deployment of multienergy microgrids (MGs). In this context, the Interreg SUDOE project IMPROVEMENT was launched at the end of the year 2019 with the aim of developing efficient solutions allowing public buildings with critical loads to be turned into net-zero-energy buildings (nZEBs). The work presented in this paper deals with the development of a predictive energy management system (PEMS) for the management of thermal resources and users' thermal comfort in public buildings. Optimization-based/optimization-free model predictive control (MPC) algorithms are presented and validated in simulations using data collected in a public building equipped with a multienergy MG. Models of the thermal MG components were developed. The strategy currently used in the building relies on proportional–integral–derivative (PID) and rule-based (RB) controllers. The interconnection between the thermal part and the electrical part of the building-integrated MG is managed by taking advantage of the solar photovoltaic (PV) power generation surplus. The optimization-based MPC EMS has the best performance but is rather computationally expensive. The optimization-free MPC EMS is slightly less efficient but has a significantly reduced computational cost, making it the best solution for in situ implementation. [ABSTRACT FROM AUTHOR]