Search

Recently, as the use of wearable devices and the demand for eco-friendly energy have increased, many studies have been conducted on triboelectric nanogenerators (TENGs), which can economically harvest energy. Paper is considered a promising substrate and frame material that can be used to manufacture self-powered TENGs, owing to its flexibility, low cost, and accessibility. Herein, we present a sandwich-structured foldable paper-based TENG (FP-TENG) that comprises flexible materials and uses paper as a substrate. The FP-TENG can generate up to 572 mW/m2 of power via contact–separation of the triboelectric electrified body at the top and bottom. With more folds of the FP-TENG, the triboelectric cross-sectional area increases, and, thus, the electrical output increases. In addition, the proposed TENG exhibits excellent durability without signal degradation under 5000 cycles of repeated pushing motions. To demonstrate its practicality, the FP-TENG was manufactured in the form of a wristwatch Velcro and connected to an electronic watch panel to supply power. Various deformations are possible with origami, and they can drive wristwatches through external forces. Therefore, the FP-TENG is expected to be utilized as a sustainable and promising eco-friendly energy source for small electronic devices. [ABSTRACT FROM AUTHOR]

In this framework, experimental tests on different battery technologies, BMS and cooling systems are extremely important to extend the battery life and BEV performance (Sehil et al. [[13]]). Electrical machines and magnetic components, high-voltage voltage power converters, and battery storage systems are some basic bricks to build an effective and efficient energy conversion environment. Electrical Machines and Power Converters The electrical power conversion from renewable energy sources plays a crucial role in the development of a sustainable society. Finally, the fil rouge of every contribution in this section is oriented to investigate the power converters, electrical machines, magnetic components, and battery storage systems in actual energy conversion applications for renewable energy sources integration by a modelling approach. [Extracted from the article]

In order to extend the service life of a highway power supply system and the level of new energy consumption, a power dispatching strategy considering the health status of multi-energy conversion equipment is proposed in this paper. Firstly, the energy and load forms of the highway power supply system are introduced, and the structure of the multi-energy conversion equipment, the topological structures of the DC–DC and DC–AC modules, and the operating characteristics are analyzed. Secondly, the module temperatures and output voltages are used as main parameters to establish the health indexes of DC–DC and DC–AC modules, and then the health index of the multi-energy conversion equipment is further calculated. Thirdly, the new energy consumption index is defined, and a multi-objective optimization model for power dispatching of highway power supply systems is established with the goal of improving the health index of multi-energy conversion equipment and the new energy consumption index. The case study shows that the power dispatching strategy in this paper can better control the temperature of each module, improve the health status of multi-energy conversion equipment, and have a high level of new energy consumption. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive bibliometric review and visualization of smart and sustainable energy consumption, delving into the challenges and opportunities of developing renewable and non-renewable energy sources. The study examines research trends and emerging themes about integrating smart solutions and sustainable energy resource consumption. The analytical methods used involve thoroughly analyzing empirical data, case studies, and review papers to map the research landscape. The results highlight dominant research topics, influential authors, and publication timelines in this field. The review identifies the key challenges in harnessing renewable and non-renewable energy sources, including the need for reliable energy sources, energy storage systems, and smart grid technologies. The paper concludes with insights into the most effective practices for promoting smart and energy-efficient methods while emphasizing the complexity of sustainable energy solutions. [ABSTRACT FROM AUTHOR]

The current development of prosumer microsources and the expected spread of electric vehicles may cause the appearance of significant current and voltage unbalance in low-voltage (LV) networks. This unbalance, which is an unfavorable phenomenon, may occur when using single-phase photovoltaic (PV) microsources and single-phase home chargers for electric vehicles. This paper presents a proposal for the symmetrization of the LV network using devices for the reconfiguration of phases in the power supply. Both the different locations of these devices and the different objective functions for device implementation are analyzed. The research was carried out on an example LV network, taking into account several variants of the development of PV microsources and home chargers for electric vehicles. The analysis indicates that the appropriate location of phase reconfiguration devices and the use of an appropriate objective function leads to a significant reduction in unfavorable unbalancing in the LV network. [ABSTRACT FROM AUTHOR]

A reasonable allocation of production schedules and savings in overall electricity costs are crucial for large manufacturing conglomerates. In this study, we develop an optimization model of off-site industrial production scheduling to address the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's power supply, and the difficulty in promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and variations in electricity prices in different places to optimize the scheduling of industrial production in various locations. The model is embedded with two sub-models, i.e., an electricity price prediction model and a distributed photovoltaic power cost model to complete the model parameters, in which the electricity price prediction model utilizes a Long Short-Term Memory (LSTM) neural network. Then, the particle swarm optimization algorithm is used to solve the optimization model. Finally, the production data of two off-site pharmaceutical factories belonging to the same large group of enterprises are substituted into the model for example analysis, and it is concluded that the optimization model can significantly reduce the electricity consumption costs of the enterprises by about 7.9%. This verifies the effectiveness of the optimization model established in this paper in reducing the cost of electricity consumption on the demand side. [ABSTRACT FROM AUTHOR]

The research aims were to construct an air-breathing paper-based microfluidic fuel cell (paper-based μ FC) and to evaluated it with different soft drinks to provide energy for their prospective use in portable devices as an emergency power source. First, in a half-cell configuration, cyclic voltammetry showed that glucose, maltose, and fructose had specific oxidation zones in the presence of platinum-ruthenium on carbon (PtRu/C) when they were individual. Still, when they were mixed, glucose was observed to be oxidized to a greater extent than fructose and maltose. After, when a paper-based μ FC was constructed, PtRu/C and platinum on carbon (Pt/C) were used as anode and cathode, the performance of this μ FC was mostly influenced by the concentration of glucose present in each soft drink, obtaining maximum power densities at room temperature of 0.061, 0.063, 0.060, and 0.073 mW cm − 2 for Coca Cola ® , Pepsi ® , Dr. Pepper ® , and 7up ® , respectively. Interestingly, when the soft drinks were cooled, the performance was increased up to 85%. Furthermore, a four-cell stack μ FC was constructed to demonstrate its usefulness as a possible power supply, obtaining a power density of 0.4 mW cm − 2 , using Coca Cola ® as fuel and air as oxidant. Together, the results of the present study indicate an alternative application of an μ FC using soft drinks as a backup source of energy in emergencies. [ABSTRACT FROM AUTHOR]

Mounting climate concerns are making energy transition inevitable. Providing a reliable, cost-effective energy supply that meets the needs of all, as set up by Sustainable Development Goal 7, and promotes climate neutrality, as set up by the European Green Deal, is a complex task that requires complex and combined interventions in various sectors and policy areas. This paper aims to conduct a systematic analysis of the scholarly work focusing on energy transition towards renewables and to contribute to the existing knowledge by offering a holistic perspective on the dynamic landscape of energy transformation and the transition to renewables. To this end, advanced bibliometric techniques, combined with a systematic in-depth review of the existing literature and desk research, are used to uncover the intellectual landscape and identify influential works and emerging themes within this critical intersection of the economic, governance, political, social, and climate dimensions of energy transition. This analysis not only highlights prevailing trends and influential works but also sets the stage for future research and discussions critical to shaping the transition to renewable energy and policy actions in a rapidly evolving world. The results are useful guidance in the formulation of policy actions. [ABSTRACT FROM AUTHOR]

This paper presents an optimization method for scheduling a multi-energy VPP (Virtual Power Plant) supply–demand balance in the power market environment of Jiangxi Province. The primary objective of this method is to improve the operational efficiency of the power grid, reduce energy costs, and facilitate economical and efficient energy distribution in the power market. The method takes into account the characteristics and uncertainties of renewable energy sources such as solar and wind energy, and incorporates advanced multi-objective optimization algorithms. Furthermore, it integrates real-time market price feedback to achieve the accurate allocation of power supply and demand. Through a case study of a multi-energy VPP in Jiangxi Province, this paper examines the optimal combination model for various energy sources within VPP, and analyzes the impact of different market environments on supply–demand balance. The results demonstrate that the proposed scheduling optimization method significantly improves economic benefits while ensuring grid stability. Compared with traditional power supply models, it reduces average electricity costs by 15% and increases renewable energy utilization efficiency by 20%. [ABSTRACT FROM AUTHOR]

Accelerating the green transformation of the power system is the inevitable path of the energy revolution; the increasing installed capacity of new energy and the penetration rate of electricity, uncertainty regarding new energy output, and the rising proportion of distributed power supply access have led to the threat against the safe and stable operation of the current power system. With the increasing uncertainty on both sides of power supply and demand, the microgrid (MG) is needed to effectually aggregate, coordinate, and optimize resources, such as adjustable resources, distributed power supply, and distributed energy storage in a certain area on the demand side. Therefore, in this paper, the uncertainty of wind power and PV is first dealt with by Latin hypercube sampling (LHS). Secondly, differentiated resources in the MG region can be divided into adjustable resources, distributed power supply, and energy storage. Adjustable resources are classified according to demand response characteristics. At the same time, the MG operating cost and carbon trading mechanism (CTM) are comprehensively considered. Finally, a low-carbon economy optimal scheduling strategy with the lowest total cost as the optimization goal is formed. Then, in order to verify the effectiveness of the proposed algorithm, three different scenarios are established for comparison. The total operating cost of the proposed algorithm is reduced by about 30%, and the total amount of carbon trading in 24 h can reach nearly 600 kg, bringing economic and social benefits to the MG. [ABSTRACT FROM AUTHOR]

The shared energy storage device acts as an energy hub between multiple microgrids to better play the complementary characteristics of the microgrid power cycle. In this paper, the cooperative operation process of shared energy storage participating in multiple island microgrid systems is researched, and the two-stage research on multi-microgrid operation mode and shared energy storage optimization service cost is focused on. In the first stage, the output of each subject is determined with the goal of profit optimization and optimal energy storage capacity, and the modified grey wolf algorithm is used to solve the problem. In the second stage, the income distribution problem is transformed into a negotiation bargaining process. The island microgrid and the shared energy storage are the two sides of the game. Combined with the non-cooperative game theory, the alternating direction multiplier method is used to reduce the shared energy storage service cost. The simulation results show that shared energy storage can optimize the allocation of multi-party resources by flexibly adjusting the control mode, improving the efficiency of resource utilization while improving the consumption of renewable energy, meeting the power demand of all parties, and realizing the sharing of energy storage resources. Simulation results show that compared with the traditional PSO algorithm, the iterative times of the GWO algorithm proposed in this paper are reduced by 35.62%, and the calculation time is shortened by 34.34%. Compared with the common GWO algorithm, the number of iterations is reduced by 18.97%, and the calculation time is shortened by 22.31%. [ABSTRACT FROM AUTHOR]

In this paper, a consensus-based model predictive control (Cb-MPC) scheme is proposed to control the active power and voltage at all nodes in grid-connected active distribution networks (ADNs) with multiple distributed energy resources (DERs). The proposed design methodology is based on a multiple-input multiple-output (MIMO) model of an ADN which accounts for both the internal and external interactions among the control loops of the DERs. To achieve the control objective, each DER unit is equipped with a controller–observer system. In particular, the observer implements the consensus algorithm to estimate the collective system state by exchanging data only with its neighbors. The scope of the controller is to solve the MPC optimal problem based on its collective state estimate, and, due to the presence of an integral term in the control action, it is robust against any unknown scenarios of the ADN, which are represented by uncertainty in the model parameters. The results of numerical simulations validate the effectiveness of the proposed method in the presence of unknown changes in the operating conditions of the ADN and of communication using a sample and hold function. [ABSTRACT FROM AUTHOR]

With the development of the power system, power users begin to use their own power supply in order to improve the power economy, but this also leads to the occurrence of the risk of self-provided power supply. The actual distribution network has few samples of power supply risk and it is difficult to identify the power supply risk by using conventional deep learning methods. In order to achieve high accuracy of self-provided power supply risk identification with small samples, this paper proposes a combination of transfer learning, convolutional block attention module (CBAM), and convolutional neural network (CNN) to identify the risk of self-provided power supply in an active distribution network. Firstly, in order to be able to further identify whether or not a risk will be caused based on completing the identification of the faulty line, we propose that it is necessary to identify whether or not the captive power supply on the faulty line is in operation. Second, in order to achieve high-precision identification and high-efficiency feature extraction, we propose to embed the CBAM into a CNN to form a CBAM-CNN model, so as to achieve high-efficiency feature extraction and high-precision risk identification. Finally, the use of transfer learning is proposed to solve the problem of low risk identification accuracy due to the small number of actual fault samples. Simulation experiments show that compared with other methods, the proposed method has the highest recognition accuracy and the best effect, and the risk recognition accuracy of active distribution network backup power is high in the case of fewer samples. [ABSTRACT FROM AUTHOR]

Unmanned aerial vehicles (UAVs) have become an integral part of modern life, serving both civilian and military applications across various sectors. However, existing power supply systems, such as batteries, often fail to provide stable, long-duration flights, limiting their applications. Previous studies have primarily focused on battery-based power, which offers limited flight endurance due to lower energy densities and higher system mass. Proton exchange membrane (PEM) fuel cells present a promising alternative, providing high power and efficiency without noise, vibrations, or greenhouse gas emissions. Due to hydrogen's high specific energy, which is substantially higher than that of combustion engines and battery-based alternatives, UAV operational time can be significantly extended. This paper investigates the potential of PEM fuel cells as an alternative power source for electric propulsion in UAVs. This study introduces an adaptive, fully functioning PEM fuel cell model, developed using a reduced-order modeling approach and optimized for UAV applications. This research demonstrates that PEM fuel cells can effectively double the flight endurance of UAVs compared to traditional battery systems, achieving energy densities of around 1700 Wh/kg versus 150–250 Wh/kg for batteries. Despite a slight increase in system mass, fuel cells enable significantly longer UAV operations. The scope of this study encompasses the comparison of battery-based and fuel cell-based propulsion systems in terms of power, mass, and flight endurance. This paper identifies the limitations and optimal applications for fuel cells, providing strong evidence for their use in UAVs where extended flight time and efficiency are critical. [ABSTRACT FROM AUTHOR]

Accurate and trustworthy forecasting of coal prices can offer theoretical support for the rational planning of coal industry output, which is of great importance in ensuring a stable and sustainable energy supply and in achieving carbon neutrality targets. This paper proposes a novel decomposition integration model, called VCNQM, to perform point and interval forecasting of coal price by a combination of variational modal decomposition (VMD), chameleon swarm algorithm (CSA), N-BEATS, and quantile regression. Initially, the variational modal decomposition is enhanced by the chameleon swarm algorithm for decomposing the coal price sequence. Then, N-BEATS is used to forecast each subsequence of coal prices, integrating all results to obtain a point forecast of coal prices. Next, interval forecasting of coal prices is achieved through quantile regression. Finally, to demonstrate the superiority of the VCNQM model's prediction, we make a cross-comparison about predictive performance between the VCNQM model and other benchmark models. According to the experimental findings, we demonstrate the following: after the decomposition by CSA-VMD, the coal price subseries' fluctuation is significantly weakened; using quantile regression provides a reliable interval prediction, which is superior to point prediction; the predicted interval coverage probability (PICP) is higher than the confidence level of 90%; the share power industry index and coal industry index have the greatest impact on coal prices in China; compared to these benchmark models, the VCNQM model's prediction errors are all reduced. Therefore, we conclude that when forecasting coal prices, the VCNQM model has an accurate and reliable prediction. [ABSTRACT FROM AUTHOR]

To address the global warming issue, China is prioritizing the development of clean energy sources such as wind and solar power under its "dual carbon target". However, the expansion of these resources is constrained by their intermittency and the spatial and temporal distribution of wind and solar energy. This paper systematically reviews the evolution of wind and solar energy reserves, their development potential, and their current status in China from a geographical perspective. In conjunction with existing research, this paper anticipates future exploration in the realm of wind–solar complementary development or multi-energy complementary development, viewed through the lens of resource quantity. The anticipated findings are intended to furnish a theoretical foundation for further studies on the development and utilization of wind and solar energy resources within China. [ABSTRACT FROM AUTHOR]

The increasing use of renewable energy sources introduces significant fluctuations in power generation, demanding enhanced regulatory capabilities to maintain the balance between power supply and demand. To promote multi-energy coupling and the local consumption of renewable energy, integrated energy systems have become a focal point of multidisciplinary research. This study models adjustable sources, networks, and loads within electric–thermal integrated energy systems as energy storage entities, forming virtual energy storage systems to participate in the optimization and scheduling of integrated energy systems. This paper investigates the modeling and control strategies of virtual energy storage systems within electric–thermal integrated energy systems. Initially, it introduces the definition, logical architecture, and technical connotations of virtual energy storage. Next, it models temperature-controlled loads as virtual energy storage systems and compares them with traditional energy storage systems, analyzing their characteristic differences and summarizing virtual energy storage system modeling methods and characteristic indicators. This paper then focuses on the specific applications of virtual energy storage systems in four typical scenarios. Finally, it explores the future development directions of virtual energy storage. [ABSTRACT FROM AUTHOR]

The operation envelope of distribution networks can obtain the independent p-q controllable range of each active node, providing an effective means to address the issues of different ownership and control objectives between distribution networks and distributed energy resources (DERs). Existing research mainly focuses on deterministic operation envelopes, neglecting the operational status of the system. To ensure the maximization of the envelope operation domain and the feasibility of decomposition, this paper proposes a modified hyperellipsoidal dynamic operation envelopes (MHDOEs) method for distribution networks based on adjustable "Degree of Squareness" hyperellipsoids. Firstly, an improved convex inner approximation method is applied to the non-convex and nonlinear model of traditional distribution networks to obtain a convex solution space strictly contained within the original feasible region of the system, ensuring the feasibility of flexible operation domain decomposition. Secondly, the embedding of the adjustable "Degree of Squareness" maximum hyperellipsoid is used to obtain the total p-q operation domain of the distribution network, facilitating the overall planning of the distribution network. Furthermore, the calculation of the maximum inscribed hyperrectangle of the hyperellipsoid is performed to achieve p-q decoupled operation among the active nodes of the distribution network. Subsequently, a correction coefficient is introduced to penalize "unknown states" during the operation domain calculation process, effectively enhancing the adaptability of the proposed method to complex stochastic scenarios. Finally, Monte Carlo methods are employed to construct various stochastic scenarios for the IEEE 33-node and IEEE 69-node systems, verifying the accuracy and decomposition feasibility of the obtained p-q operation domains. [ABSTRACT FROM AUTHOR]

Nowadays, intermittent energy resources, such as wind turbines, and direct current (DC) transmission have been extensively integrated into power systems. This paper proposes an identifying method for weak lines of novel power systems with intermittent energy resources and DC lines integration, which aims to provide decision making for control strategies of novel power systems and prevent system blackouts. First, from the perspective of power system safety and stability, a series of risk indicators for the risk assessment of vulnerable lines is proposed. Then, lines in the system are tripped one by one. The calculation method for the proposed risk indicators is introduced. The impact of each line outage on system safety and stability can be fairly evaluated by these proposed risk indicators. On this basis, each risk assessment indicator is weighted to obtain a comprehensive risk assessment indicator, and then the risk caused by each line outage on the system can be quantified efficiently. Finally, the test system of a modified IEEE-39 bus system with wind farms and DC lines integration is used to verify the applicability of the proposed method, and the effectiveness of the proposed method is also demonstrated by comparing with existing methods. [ABSTRACT FROM AUTHOR]

Microgrids have increased in popularity thanks to both the integration of renewable energy resources and their energy distribution capability for remote locations. Moreover, the microgrids, mainly using multiple generators connected in parallel, acquire additional advantages by using both Hot-Swap and Current-Sharing techniques. This paper presents the development of a Hardware in the Loop platform to test Current-Sharing algorithms. It is reinforced that the use of a real-time simulation based on Hardware in the Loop is a viable and cost-effective alternative in the validation of controllers. The platform was developed in a graphical programming environment (LabVIEW 2015) and implemented with NI MyRIO 1900 (National Instruments Corp., Austin, TX, USA) development boards for easier reproducibility. The entire code project is openly available and provided in this paper. A system of photovoltaic energy generators was used to evaluate the performance of the HIL platform. As a result, the platform was able to reproduce a similar behavior to the photovoltaic generator, presenting average mean errors of 0.4 V and 0.2 A in its voltage and current, respectively. Additionally, the platform showed its capability to test Current-Sharing algorithms in the occurrence of Hot-Swap events. This work contributes with a validation tool for energy management systems applied to microgrids. [ABSTRACT FROM AUTHOR]

To address challenges in locating high-impedance grounding faults (HIGFs) and isolating fault areas in resonant grounding systems, this paper proposes a novel fault identification method based on coordinating a Peterson coil and a resistance grounding system. This method ensures power supply reliability by extinguishing the fault arc during transient faults with the Peterson coil. When a fault is determined to be permanent, the neutral point switches to a resistance grounding mode, ensuring regular distribution of zero-sequence currents in the network, thereby addressing the challenges of HIGF localization and fault area isolation. Fault calibration and nature determination rely on recognizing neutral point displacement voltage waveforms and dynamic characteristics, eliminating interference from asymmetric phase voltage variations. Fault area identification involves assessing the polarity of zero-sequence current waveforms attenuation during grounding mode switching, preventing misjudgments in grounding protection due to random initial fault angles and Peterson coil compensation states. Field experiments validate the feasibility of this fault location method and its control strategy. [ABSTRACT FROM AUTHOR]

South Africa is currently experiencing an energy crisis because of a mismatch between energy supply and demand. Increasing energy demand necessitates the adequate operation of generation and transmission facilities to maintain the reliability of the power system. Transmission line compensation is used to increase the ability to transfer power, thereby enhancing system stability, voltage regulation, and reactive power balance. Also, in recent years, the introduction of renewable energy sources (RES) has proven to be effective in supporting the grid by providing additional energy. As a result, the dynamics of power systems have changed, and many developing nations are adopting the integration of renewable energy into the grid to increase the aspect ratio of the energy availability factor. While both techniques contribute to the grid's ability to meet energy demand, they frequently introduce technical challenges that affect the stability and protection of the systems. This paper provides a comprehensive review of the challenges introduced by transmission line compensation and the integration of renewable energy, as well as the various techniques proposed in the literature to address these issues. Different compensation techniques, including fault detection, classification, and location, for compensated and uncompensated transmission lines, including those connected to renewable energy sources, are reviewed. This paper then analyzes the adaptive distance protection schemes available in the literature to mitigate the impact of compensation/integration of RES into the grid. Based on the literature reviewed, it is essential for protection engineers to understand the dynamics introduced by network topology incorporating a combination of RES and heavily compensated transmission lines. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive analysis of optimal energy community design, leveraging time-of-use pricing mechanisms and techno-economic parameters. Focusing on a case study of Valongo, Portugal, this study explores the intricate interplay between energy infrastructure planning, economic considerations, and pricing dynamics. Through a systematic approach, various factors, such as renewable energy integration, demand–response strategies, and investment costs, are evaluated to formulate an efficient and sustainable energy community model. Time-of-use pricing schemes are incorporated to reflect the dynamic nature of energy markets and consumer behavior. By integrating techno-economic analyses, this study aims to optimize energy resource allocation while ensuring cost-effectiveness and environmental sustainability. The influence of optimized sizes of photovoltaics (PV), battery storage, and electrical vehicles (EVs) on self-sufficiency rates, self-consumption rates and CO2 savings is analyzed. The findings offer valuable insights into the design and implementation of energy communities in urban settings, highlighting the importance of adaptive strategies in the transition towards a resilient and low-carbon energy future. The novelty of this paper lies in its comprehensive approach to energy community design, which integrates time-of-use pricing mechanisms with techno-economic parameters. By focusing on the specific case of Valongo, Portugal, it addresses the unique challenges and opportunities present in urban settings. Additionally, the analysis considers the interaction between renewable energy production, demand profiles and investment costs, providing valuable insights for optimizing resource allocation and achieving both cost-effectiveness and environmental sustainability. [ABSTRACT FROM AUTHOR]

This paper explores the significant role of Wastewater Treatment Plants (WWTPs) in achieving environmental sustainability, with a particular focus on enhancing energy efficiency, resource recovery, and water reuse. WWTPs are crucial for removing pollutants and recovering resources from wastewater, thereby protecting public health and biodiversity. However, they are also associated with high operational costs, substantial carbon footprints, and energy-intensive processes. This article delves into various strategies and technologies to overcome these challenges, aiming to transform WWTPs from energy consumers to energy-efficient resource recovery hubs. Techniques such as anaerobic digestion and the use of advanced oxidation processes and microbial fuel cells are investigated for their potential in energy recovery and efficiency enhancement. Success stories from around the globe are highlighted to demonstrate the feasibility of transitioning to energy-positive WWTP operations. The integration of water reuse systems is also discussed, highlighting recent advancements that enable treated wastewater to be repurposed for agricultural, industrial, and potable uses, thereby promoting sustainability and water conservation. This paper emphasizes the importance of integrating cutting-edge energy management practices to minimize environmental impacts, reduce operational costs, and contribute to a more sustainable water sector. [ABSTRACT FROM AUTHOR]

Deploying renewable generation to replace conventional fossil-fuel-based energy supplies provides an important pathway for the decarbonization of steelmaking plants. Meanwhile, it is also crucial to improve the flexibility of blast-furnace-gas-fired combined-cycle power plants (BFGCCs) to ease the accommodation of uncertain renewable generation. To this end, this paper proposes the deployment of a molten salt heat storage (MSHS) system in BFGCCs to store the heat of gas turbine flue gas so that the power–heat coupling of these BFGCCs can be unlocked to enhance the flexibility of the energy supply. A stochastic capacity optimization of an integrated BFGCC–MSHS–wind–solar (BMWS) energy system is presented to determine the optimal installed capacities of a BFG holder, MSHS, wind turbine, and PV panel, aiming to achieve an economic and safe energy supply for the entire system. Multiple scenarios considering uncertain fluctuations in load demands and renewable generation are generated with the Monte Carlo method based on a typical scenario. These scenarios are then reduced to representative scenarios using the synchronous substitution and reduction method for stochastic capacity optimization to enhance the reliability of the results. The case study results demonstrate that configuring MSHS reduces the total annualized cost of the BMWS system by 2.28%. Furthermore, considering the uncertainties of the power/heating load and wind/PV generation can reduce the expected annualized total cost of the BMWS system and the corresponding standard deviation by 5.66% and 81.45%, respectively. The BMWS system can achieve 730.68 tons of equivalent CO2 reduction in 24 h due to the successful utilization of renewable energy. This paper provides an effective approach for the decarbonization of energy generation systems in steelmaking plants. [ABSTRACT FROM AUTHOR]

This paper is concerned with a hydraulic cylinder directly controlled by a variable speed motor-driven fixed-displacement pump. The considered configuration is referred to as a one-motor-one-pump (1M1P) motor-controlled hydraulic cylinder (MCC). A 1M1P MCC with a hydraulically driven passive load-holding function enabled by controlled system pressures is proposed. The proposed load-holding functionality works if there is a standstill command, a loss of power supply, or a hose rupture. Additionally, this paper conducts a comprehensive analysis of the proposed system's operation and load-holding function across four quadrants. The simulation results demonstrate four-quadrant operation and good load-holding performance under the aforementioned scenarios. In conclusion, the proposed 1M1P MCC can be successfully used on practical applications characterized by overrunning loads and four quadrant operation. [ABSTRACT FROM AUTHOR]

The DC distribution network is a low-inertia system, which is very sensitive to load disturbance, system failure, and other factors. By adding virtual capacitance to the converter connected to the power supply, the virtual inertia of the DC power grid can be improved. Firstly, this paper proposes a strategy for adjusting virtual capacitance based on the voltage change rate to achieve adaptive control of virtual inertia, which enables the converter to quickly absorb or release energy during power fluctuations. Secondly, the adaptivity of the strategy is improved and the main control parameters in the proposed control method are qualitatively analyzed. Finally, the four-terminal photovoltaic storage DC distribution network system is constructed. Through Simulink, the adaptive virtual inertia control is incorporated on the battery side to simulate and validate the effectiveness of the strategy and the rationality of parameter analysis. The results show that this method can provide flexible and adjustable inertia support for DC grids and improve the voltage stability of DC grids. [ABSTRACT FROM AUTHOR]

In this paper, the notion of a cohesive and self-sufficient grid is proposed. Based on a cohesive and self-sufficient virtual microgrid, an active distribution network is optimally planned, and an optimal configuration of demand-side resources, distributed generations, and energy storage systems are generated. To cope with stochastic uncertainty from forecast error in wind speed and load, flexibility reserves are needed. In this paper, the supply relation between flexibility and uncertainty is quantified and integrated in an innovative index which is defined as cohesion. The optimization objectives are a minimized operational cost and system net-ability cohesion as well as self-sufficiency, which is defined as the abilities both to supply local load and to deal with potential uncertainty. After testing the optimal configuration in the PG&E 69 bus system, it is found that with a more cohesive VM partition, the self-sufficiency of VMs is also increased. Also, a case study on uncertainty-caused system imbalance is carried out to show how flexibility resources are utilized in real-time operational balance. [ABSTRACT FROM AUTHOR]

The modern world is moving towards a zero-emission economy; therefore, various actions are being taken to reduce the share of fossil fuels in energy production. The article examines the potential for the continued expansion of photovoltaic farms, with a special emphasis on farms utilising east–west panel orientation. The east–west orientation is an innovative solution with many advantages over the traditional north–south arrangement. The paper also makes a detailed assessment of the photovoltaic farm environment by applying two analyses based on the following factors: Political, Economic, Social, and Technological (PEST) and Demographic, Economic, Environmental, Political, Legal, Informational, Social, and Technological (DEEPLIST) factors. This is followed by an insightful, comprehensive review of the most important factors that contribute to the efficiency of photovoltaic installations, namely site conditions, existing infrastructure, and ability to connect to the electricity grid. The paper also devotes space to an analysis of daily energy price changes that affect the economic efficiency of the installation and discusses the potential for energy storage in the context of photovoltaic farms. The development of photovoltaics also requires investing in energy storage. All discussed issues fall within the scope of photovoltaic farm development and optimal use of energy resources. [ABSTRACT FROM AUTHOR]

As the main source of energy supply and carbon emissions, the oil and gas industry has entered the comprehensive low-carbon transition stage driven by various factors. Since different oil companies possess distinct understandings of transition paths, the effect of low carbon transition varies greatly. Obviously, it is necessary to evaluate the performance of low-carbon transitions within the oil and gas industry. Therefore, in this paper, 10 major international oil companies are taken as examples, and a super-efficiency slack-based measurement (super-SBM) model is applied in the present study to analyze the efficiency of low-carbon transitions. Furthermore, the logarithmic mean Divisia index (LMDI) is used to decompose the driving factors of carbon emissions and analyze their impact on the low-carbon transition of international oil companies. The obtained results reveal that although major oil companies have taken different measures in low-carbon transition and achieved a year-on-year reduction in carbon emissions, from the perspective of the efficiency of the entire production and operation process, these oil companies are inefficient in carbon emissions and need to adopt more effective low-carbon transition strategies; Moreover, after the further decomposition of the carbon emission driving factors of the 10 companies, it is found that improving the energy consumption intensity and development level of oil companies can effectively improve the effect of low-carbon transition of international oil companies. Drawing on the above findings, this paper puts forward suggestions for the low-carbon transition of energy companies, thus providing theoretical support and guidance for energy companies in different countries to implement low-carbon transition and green development strategies. [ABSTRACT FROM AUTHOR]

This paper proposes a hybrid power supply system for commercial drones. The proposed hybrid power supply system consists of a lithium polymer battery, a supercapacitor, and a power converter for charging the supercapacitor. In the proposed system, the supercapacitor is pre-charged with a lithium polymer battery through a power converter, and the supercapacitor first supplies the power required for the drone's initial startup and lift-up. Afterward, in the section where the power consumption of the drone is low, the battery and the supercapacitor supply power together, minimizing the stress on the battery. To verify the proposed hybrid power supply system, a computer simulation was conducted, the actual hardware was fabricated, and experiments were performed. [ABSTRACT FROM AUTHOR]

The lingering COVID-19 pandemic and ongoing war between Russia and Ukraine have wreaked havoc on the global oil supply chain. The current disruption of the oil supply chain and the rapidly growing energy demand created unprecedented oil shortages and raised the oil price beyond the affordable level. As worldwide oil price hikes continue, there is an urgent need for developing alternative energy sources, such as smart rural energy. Despite its enormous potential as a viable alternative to traditional fossil fuel-based energy sources, smart rural energy has never been fully utilized in society. The limited use of smart rural energy may be related to its lack of commercialization, which could have created more eco-friendly and cost-efficient alternative energy sources. This paper assesses the eco-friendliness and cost-efficiency of smart rural energy sources such as solar, wind, biomass, and hydropower for the first time. This paper is also one of the first studies that intends to develop viable strategic plans for commercializing smart rural energy using strategy maps, which subsequently helps increase public awareness of renewable energy by creating visual communication tools that convey the benefits of smart rural energy commercialization to multiple stakeholders, including government entities, business communities, and energy consumers. [ABSTRACT FROM AUTHOR]

With high real-time performance and a good filtering effect, the wavelet transform-based real-time filter is more commonly used in the fusion magnet power supply. Considering the signal characteristics of the fusion magnet power supply, the sliding time window method is widely used to satisfy the requirements of filtering efficiency. In this paper, an updated half-edge extension method is proposed to improve the boundary effect of sliding window data. Moreover, the hardware-based wavelet loopback structure is proposed to avoid the double computation of long sliding window data, thereby improving real-time performance and satisfying the demands of fusion magnet power supply filtering. The proposed half-edge extension method and the wavelet loopback structure are implemented by designed FPGA and experimented on the Experimental and Advanced Superconducting Tokamak (EAST) fusion magnet power supply system to verify the filtering efficiency. According to the experiment's results, the proposed half-edge extension method has a better filtering effect, and the proposed wavelet loopback structure decreases the time by 67.4%, which can satisfy the requirements of the power supply system. [ABSTRACT FROM AUTHOR]

At present, electrified railroads with complex road conditions are facing the problems of the existence of a single power supply method, the deterioration in power quality, and the difficulty in recycling regenerative braking energy. In order to improve the above problems, this paper establishes a traction power supply system containing photovoltaic units, proposes an optimized compensation model for the RPC (railroad power conditioner), and improves the particle swarm algorithm for solving the reference value of RPC compensation power. First, the structure of the RPC-based traction photovoltaic power generation system and the establishment of the integrated energy management strategy of the system are constructed. Then, the back-to-back converter compensation model with power quality index parameter constraints is established, which establishes the optimization function with the objectives of minimizing the negative sequence current, maximizing the power factor, and minimizing the RPC compensation power, as well as establishes constraints on the active converter capacity and three-phase voltage imbalance. Then, the particle swarm algorithm for solving the RPC compensation power reference value is improved, specifically in the original PSO by introducing dynamically changing inertia weights and learning factors. This not only solves the problem of the single power supply and realizes the nearby consumption of photovoltaic units in the traction system, but also realizes the recycling of regenerative braking energy and the coordinated control of the traction photovoltaic power generation system, improves the power quality of the system, and meets the demand of the RPC for real-time control. In order to verify the effectiveness of the optimized compensation model established in this paper and improve the convergence of the particle swarm algorithm for solving the RPC compensation power reference value, a simulation model of the traction PV power generation system is established in MATLAB/Simulink, and a real-time simulation is carried out to verify it based on the preset working condition data. The results show that the RPC optimization compensation model developed in this paper can coordinate the control system energy flow and improve the system power quality (the power factor increases and the negative sequence current decreases). The improved particle swarm algorithm is more convergent. [ABSTRACT FROM AUTHOR]

Fossil energy consumption and environmental protection issues have pushed electric vehicles (EVs) to become one of the alternatives to traditional fossil-fuel vehicles. EV refers to a vehicle that uses electric energy as power and is driven by an electric motor. The electric energy of EVs is stored in batteries. When the EV is not traveling, the battery can provide power for other loads. Therefore, with the increase in the number of EVs and the load of the power grid, the EV-to-grid (V2G) mode, which uses EVs to supply power to the power grid, has gradually entered the field of vision of researchers. The physical connection mode, charge and discharge technology, and energy management strategy are the main topics of the current review papers; however, there is a lack of systematic research on V2G modeling, framework, and business models. This paper describes the concepts of the spatio-temporal distribution model and the adjustable capacity of EVs. In addition, common constraints and methods in optimization are introduced. Moreover, this paper introduces the interactive relationship among power grids, load aggregators, and EV users. Furthermore, the business model of V2G is introduced and analyzed from various perspectives. Finally, the future development of V2G is pointed out. This paper's goal is to provide an overview of the present V2G application scenarios and to identify any challenges that must be overcome. [ABSTRACT FROM AUTHOR]

As the penetration of renewable energy sources into a power system increases, the significance of precise short-term forecasts for wind power generation becomes paramount. However, the erratic and non-periodic nature of wind poses challenges in accurately predicting the output. This paper presents a comprehensive investigation into forecasting wind power generation for the following day, using three machine learning models: long short-term memory (LSTM), convolutional neural network-bidirectional LSTM (CNN-biLSTM), and light gradient boosting machine (LGBM). In addition, this paper proposes a method to improve the prediction performance of LGBM by separating data according to the distribution of features, and training and testing each separated dataset with a distinct model. This study includes a comparative analysis of the performance of the proposed models in predicting wind turbine output, offering valuable insights into their respective efficiencies. The results of this investigation were analyzed for two geographically distinct wind farms (Korea and the UK). The findings of this study are expected to facilitate the selection of efficient prediction models within the forecast accuracy auxiliary service market and assist grid operators in ensuring reliable power supply for the grid. [ABSTRACT FROM AUTHOR]

The research problem of this paper is related to numerous open questions in the field of energy, its understanding, its use, and the challenges of the energy future. After the introductory part, in which a brief historical overview of energy literacy is provided, the paper focuses on energy literacy, its emergence, and the different approaches to its definition and measurement. The paper analyzes the energy literacy of students at the Faculty of Economics in Rijeka based on their cognitive, affective, and behavioral skills. Their knowledge about energy, energy processes, and the energy efficiency of the objects they encounter on a daily basis is examined. Their personal attitudes and values are examined through various forms of personal initiatives and active participation in energy sustainability projects. Finally, the habits and behavioral patterns that the respondents have in their daily lives and their tendencies to save energy resources and find energy-efficient solutions are examined. Despite some positive findings, the current results are not satisfactory and point to the creation of adequate public policies with a particular focus on education and the role of the corrective mechanisms of the state, but also the need for joint negotiations between policy makers, regulators, scientists, representatives of civil society, and the business community. The particular contribution of this work is reflected in being the first research of its kind conducted among Croatian economics students, as well as among Croatian students in general; in the creation of a research instrument that is conceptually consistent with the findings from the existing literature, but with an original set of questions within each energy literacy skill adapted to the cultural and sociological background of the respondents; and in a kind of progress from previous research by taking into account the quantitative aspect (in addition to the qualitative) assessment of the respondents' energy literacy. [ABSTRACT FROM AUTHOR]

Due to a rising share of renewable energy sources on the production side and electrification of transport and heating on the consumption side, the efficient management of flexibility in distribution networks is crucial for ensuring optimal operation and utilization of resources. Nowadays, the sensitivity-based approach is mainly used in medium-voltage (MV) networks for regulating voltage profiles with reactive power of distributed energy resources (DER). The main disadvantage of the simplified sensitivity-based method is its inaccuracy in case of a high deviation of the network voltage from the nominal values. Furthermore, it was also noted that despite the fact that the method is well described in the literature, there is a lack of systematic approach to its implementation in real-life applications. Thus, the main objective of this paper is to address this disadvantage and to propose an algorithm designed to calculate required consumer flexibility in near real-time to ensure distribution grid operation within operational criteria. In the first part of the paper, network state, including line loading and node voltages, is assessed to determine distribution network node capacity. By analyzing the sensitivity of network busbars to changes in consumption and production, our algorithm effectively identifies the most efficient nodes and facilitates strategic decision-making for resource allocation. We demonstrate the effectiveness of our approach through simulations of real-world distribution network data, highlighting its ability to enhance network flexibility and improve resource utilization. Leveraging sensitivity coefficients, the algorithm enables flexible consumption and production management across various scenarios, supporting the transition to a more dynamic and efficient power system. [ABSTRACT FROM AUTHOR]

Recently, there has been a significant increase in the integration of distributed energy resources (DERs) such as small-scale photovoltaic systems and wind turbines in power distribution systems. When the aggregated outputs of DERs are combined, excessive reverse current may occur in distribution lines, leading to overvoltage issues and exceeding thermal limits of the distribution lines. To address these issues, it is necessary to limit the output of DERs to a certain level, which results in constraining the hosting capacity of DERs in the distribution system. In this paper, coordination control methodologies of DERs are developed and executed to mitigate the overvoltage and overcurrent induced by DERs, thereby increasing the hosting capacity for DERs of the distribution system. This paper proposes three coordinated approaches of active and reactive power control of DERs, namely Var Precedence, Watt Precedence, and Integrated Watt and Var Control. The Var and Watt Precedence prioritizes reactive power for voltage (Q–V) and active power for current (P–I) to address network congestion, thereby enhancing hosting capacity. Conversely, the Integrated Var and Watt Precedence propose a novel algorithm that combines four control indices (Q–V, P–V, Q–I, and P–I) to solve network problems while maximizing hosting capacity. The three proposed methods are based on the sensitivity analysis of voltage and current to the active and reactive power outputs at the DER installation locations on the distribution lines, aiming to minimize DER active power curtailment. Each sensitivity is derived from linearized power equations at the operating points of the distribution system. To minimize the computation burden of iterative computation, each proposed method decouples active and reactive power and proceeds with sequential control in its own unique way, iteratively determining the precise output control of distributed power sources to reduce linearization errors. The three proposed algorithms are verified via case studies, evaluating their performance compared to conventional approaches. The case studies exhibit superior control effectiveness of the proposed DER power control methods compared to conventional methods when issues such as overvoltage and overcurrent occur simultaneously in the distribution line so that the DER hosting capacity of the system can be improved. [ABSTRACT FROM AUTHOR]

The energy transition introduces new technical standards, laws and regulations regarding the stability and reliability of energy grids and systems. Due to the non-existence of a measuring standard, key performance indicators (KPIs) were developed to enable the measurement and comparison of individual energy grid (namely electricity, heat and gas grid) and system supportabilities while also promoting well-founded decision-making and optimization efforts. Inconsistencies in definitions concerning fundamental energy terms and the correlations between them inhibit the effective usage of the KPIs. Therefore, the overarching issue of the security of energy supply and its related subjects were also approached. The primary subject of this paper is the development of two new KPIs to measure and compare the energy grid and system supportability. These KPIs are based on spatio-temporal conditions in their respective grids. The usage and benefits of the developed KPIs are exemplarily highlighted by analyzing the impact of a scenario with the integration of a large-scale heat pump into the electricity and heat grid. The energy grid supportability is determined for each grid, whereas the energy system supportability takes the interactions of the electricity and heat grid into account. The developed KPIs are intended to enable stakeholders to identify areas with optimization potential in energy grids and systems. Moreover, the KPIs can be used to create a standardized evaluation method for regulatory requirements. [ABSTRACT FROM AUTHOR]

Low or even zero carbon dioxide emissions will be an essential requirement for energy supplies in the near future. Besides transport and electricity generation, industry is another large carbon emitter. Hydrogen produced by renewable energy provides a flexible way of utilizing that energy. Hydrogen, as an energy carrier, could be stored in a large capacity compared to electricity. In Sweden, hydrogen will be used to replace coal for steel production. This paper discusses how the need for electricity to produce hydrogen will affect the electricity supply and power flow in the Swedish power grid, and whether it will result in increased emissions in other regions. Data of the Swedish system will be used to study the feasibility of implementing the hydrogen system from the power system viewpoint, and discuss the electricity price and emission issues caused by the hydrogen production in different scenarios. This paper concludes that the Swedish power grid is feasible for accommodating the additional electricity capacity requirement of producing green hydrogen for the steel industry. The obtained results could be references for decision makers, investors, and power system operators. [ABSTRACT FROM AUTHOR]

Ever-increasing penetration of distributed energy resources (DERs) in the power grids, alongside their numerous benefits, brings new challenges that call for enhanced solutions in the field of control and management of power grids. The majority of the available research have considered either distribution or transmission grids in their studies. In this paper, a comprehensive review of the effects of DERs on the distribution and transmission grids is performed. The focus of this paper is on hierarchical management methods in order to categorize different approaches and highlight the gaps. Moreover, a review is conducted in the field of the newly introduced distributed energy resources management system (DERMS) concept. A DERMS can facilitate the hierarchical energy management procedure due to its functionalities and broad capabilities. Hence, its implementation in energy management and its impact on the power grid will be assessed with the aid of a co-simulation platform that considers both transmission and distribution grids. [ABSTRACT FROM AUTHOR]

This paper presents a preliminary study of a 25 kV–50 Hz railway substation power supply system. The control of a back-to-back converter based on modular multilevel converter (MMC) technology was investigated to fit with the power quality requirements of the application. One of the main challenges is the presence of constraining load conditions, under which the train circulation variability, low-frequency harmonics and critical power transients can notably decrease the power quality and lead to instability. In order to address this, cascaded controllers based on resonant controllers are proposed to ensure the desired performance. Furthermore, balancing voltage algorithms are added to avoid stress phenomena and additional losses in the studied power conversion interface. The paper presents the design of the control stages and demonstrates the robust performance of the system using a realistic loading condition of a railway substation. [ABSTRACT FROM AUTHOR]

The application of electrochemical cells as a source unit of electrical energy is rapidly growing—used in electric vehicles and other electric mobility devices, as well as in energy supply systems—as energy storage, often together with renewable energy sources. The key element of such systems is the power electronic converter used for DC energy storage and AC grid interfacing. It should be bidirectional to charge and discharge the battery when it is necessary. Two-stage battery interface converters are the most common; their DC-DC stage controls the battery current and adjusts voltage, but the DC-AC stage (inverter or frontend) controls the current in the grid. The use of unfolding inverters in two-stage battery interfaces can have some advantages. In this case, the DC-DC converter produces half-sinewave pulsating voltages and currents, but the unfolding circuit changes the polarity of the voltages and currents and produces no switching losses. Another trend of modern power electronics is the principle of partial power processing. In this case, power electronic converters deal only with a part of the total power; therefore, losses in such converters are reduced. This paper considers combining unfolding frontends with partial power DC-DC converters that enable the further reduction in losses. In this paper, it is shown that such implementation of the partial power conversion principle in semi-DC-AC systems is really possible based on the real-time matching of the voltage of the partial-power DC-DC converter, battery voltage (which depends on its state of charge) and the rectified instantaneous voltage of the AC grid. [ABSTRACT FROM AUTHOR]

In South Korea, Renewable Energy Sources (RES) have been increasing with the application of energy policies, such as Feed in Tariff (FIT) and the Renewable Portfolio Standard (RPS). However, a rapid increase in RES supply leads to an uncertain power supply due to the intermittent output of RES. A representative example is the curtailment of Wind Turbines (WT), which frequently occurs in Jeju Island, South Korea. The proportion of RES power on Jeju Island is 67%, and there are cases where WT is curtailed among the operable sections to maintain the balance of power supply and demand. This paper applies Power-to-Gas (P2G) technology to hydrogenate, store, and utilize unused power to solve this problem. In this paper, Aewol-eup in Jeju Island is selected as a target site for case study. An Integrated Energy System (IES) for various energy operations is designed to control RES output. This paper proposes the optimal facility configuration and finally drives the optimal design and operation solution of IES by analyzing the objective functions and focusing on the Independent Power Producer (IPP) perspective. [ABSTRACT FROM AUTHOR]

Heavy oil resources are abundant globally, holding immense development potential. However, conventional thermal recovery methods such as steam injection are plagued by high heat loss, substantial carbon emissions, and significant water consumption, making them incompatible with carbon reduction goals and the sustainable socioeconomic development demands. A new method of high-frequency electromagnetic in situ heating, which targets polar molecules, can convert electromagnetic energy into heat so as to achieve rapid volumetric heating of the reservoir. This method has the potential to overcome the drawbacks of traditional techniques. Nevertheless, it faces significant drawbacks such as limited heating range and inadequate energy supply during later production stages, which necessitates auxiliary enhancement measures. Various enhancement measures have been reported, including nitrogen injection, hydrocarbon solvent injection, or the use of nano-metal oxide injections. These methods are hindered by issues such as pure nitrogen being easy to breakthrough, high costs, and metal pollution. Through extensive literature review, this article charts the evolution of high-frequency electromagnetic in situ heating technology for heavy oil and the current understanding of the coupled heat and mass transfer mechanisms underlying this technology. Moreover, based on a profound analysis of the technology's progression trends, this work introduces a new direction: CO2-N2 co-injection as an enhancement strategy for high-frequency electromagnetic in situ heavy oil recovery. There is promising potential for the development of new technologies in the future that combine high efficiency, low carbon emissions, environmental friendliness, economic viability, and energy conservation. Furthermore, some research prospects in low-carbon situations and challenges for the new technology in future are presented in detail. All in all, the contribution of the paper lies in the summarizing of some main drawbacks of current enhanced electromagnetic in situ thermal recovery methods, and presents a novel research direction of using CO2-N2 co-injection as an enhancement strategy based on its current research status in low-carbon situations. [ABSTRACT FROM AUTHOR]

To realize a carbon-efficient and economically optimized dispatch of the integrated energy system (IES), this paper introduces a highly efficient dispatch strategy that integrates demand response within a tiered carbon trading mechanism. Firstly, an efficient dispatch model making use of CHP and P2G technologies is developed to strengthen the flexibility of the IES. Secondly, an improved demand response model based on the price elasticity matrix and the capacity for the substitution of energy supply modes is constructed, taking into account three different kinds of loads: heat, gas, and electricity. Subsequently, the implementation of a reward and penalty-based tiered carbon trading mechanism regulates the system's carbon trading costs and emissions. Ultimately, the goal of the objective function is to minimize the overall costs, encompassing energy purchase, operation and maintenance, carbon trading, and compensation. The original problem is reformulated into a mixed-integer linear programming problem, which is solved using CPLEX. The simulation results from four example scenarios demonstrate that, compared with the conventional carbon trading approach, the aggregate system costs are reduced by 2.44% and carbon emissions are reduced by 3.93% when incorporating the tiered carbon trading mechanism. Subsequent to the adoption of demand response, there is a 2.47% decrease in the total system cost. The proposed scheduling strategy is validated as valuable to ensure the low-carbon and economically efficient functioning of the integrated energy system. [ABSTRACT FROM AUTHOR]

The decarbonization of power systems plays a great part in the carbon neutrality goal. Currently, researchers have explored reducing carbon in power systems in terms of the optimization of energy supply structure and operation strategies, but ignored the carbon reduction potential of users. To investigate the carbon reduction capability of users and further promote power system decarbonization through the active response of electricity loads, this paper proposes a carbon-reduction-oriented demand response (CRODR) technology based on generalized nodal carbon emission flow theory. First, the framework of the CRODR mechanism is established to provide an interaction baseline for users facing carbon reduction guiding signals. Secondly, the generalized nodal carbon emission flow theory is introduced to provide a calculation method for the guiding signals, considering dynamic electricity carbon emission factors with various spatiotemporal resolutions. Then, a matrix-based method is proposed to efficiently solve the carbon emission flow and obtain the guiding signals. On this basis, an optimal load-regulating model to help users meet their carbon reduction goals is built, and a carbon reduction benefit-evaluation method is proposed. Case studies on China's national power system and a textile company verify that CRODR technology can realize efficient carbon reduction through load shifting while maintaining the total power consumption of users. The proposed CRODR technology is expected to provide a theoretical basis and guiding mechanism for promoting carbon reduction throughout the entire power system. [ABSTRACT FROM AUTHOR]

With the gradual depletion of fossil energy sources and the diversification of users' energy demand, combined cooling, heating and power (CCHP) microgrids have become a hot technology to improve energy efficiency and promote efficient and synergistic energy operation. However, the uncertainty and correlation of wind power and photovoltaic (PV) outputs have posed a great challenge to the reliability of CCHP system operation, so CCHP systems are often equipped with energy storage devices to improve system flexibility to ensure the reliability of energy supply. However, system-owned reserves still have shortcomings such as high investment O&M costs and large space requirements. As an emerging model, "shared energy storage" can reduce the investment pressure of users and open up new ways for the economic and stable operation of CCHP systems. Therefore, based on the scenario of wind and solar power correlation and considering different types of load flexibility, this paper proposes to construct a shared energy storage station (SESS)-CCHP double-layer synergistic optimal allocation model. The model incorporates the consideration of the actual operation strategy of the CCHP system in the planning stage of energy storage. An example analysis shows that SESS reduces the total operating cost of the CCHP system by 25.96% and improves the new energy consumption rate by 10.46% compared with no energy storage. Compared with the system independently configured with energy storage, the cost saving is 2.14%, thus validating the effectiveness of the proposed model. [ABSTRACT FROM AUTHOR]

Compared to the AC counterpart, the DC shore power system provides a significant advantage of efficient power supply from renewable sources to ships and onshore loads. Super-capacitors serve as key energy storage units in such a system to buffer the power fluctuations and collect the regenerative energy. However, the ultra-wide voltage range of super-capacitors imposes a significant challenge in the topology selection and efficiency optimization of the interfacing isolated bidirectional DC–DC converter. To tackle this challenge, this paper analyzes and compares two promising converter topologies, which are a configurable modular two-level dual-active bridge (CM-2L-DAB) and a three-level dual-active bridge (3L-DAB). To facilitate an ultra-wide voltage range, extended phase-shift (EPS) modulation in conjunction with the topology reconfiguration is analyzed for the CM-2L-DAB, while a hybrid modulation scheme is proposed for the 3L-DAB. A unified design approach is provided for both topologies, which also yields to the power loss modeling. On this basis, the CM-2L-DAB and 3L-DAB are thoroughly compared in terms of the modulation schemes, current stress, soft-switching operation, power conversion efficiency, material usage, closed-loop control scheme, and reliability. A prominent conclusion can be drawn that the CM-2L-DAB provides a higher efficiency than the 3L-DAB over the whole voltage range, but it relies on additional relays to reconfigure its topology which results in lower reliability and dynamic performance than the 3L-DAB. [ABSTRACT FROM AUTHOR]