Search

With the ongoing expansion and interconnection of electrical power systems, alongside the rapid proliferation of renewable distributed generations (DGs), the short-circuit extent in the power grid is experiencing a significant rise. Fault current limiters (FCLs) have been introduced in an effort to address this issue, ensuring the robustness and sustainability of expensive power system components when confronted with short-circuit faults. Among the various types of FCLs, bridge-type DC reactor fault current limiters (BDCR-FCLs) have emerged as one of the most promising options. While BDCR-FCLs have shown excellent properties in limiting harmful short-circuit currents, they are also advantageous in other respects. This paper investigates the supplementary functionalities of BDCR-FCLs as a multifaceted device towards the enhancement of the quality of supplied energy in terms of total harmonic distortion (THD) reduction, power factor (PF) correction, peak current reduction for nonlinear loads, and soft load variation effects, as well as their capability to limit fault current. To this aim, the capabilities of BDCR-FCLs have been studied through various simulated case studies in PSCAD/EMTDC software V5.0.1, in addition to experimental tests considering an AC microgrid connected to a DC system. The experimental and simulation investigations verify the superior multifaceted functionalities BDCR-FCLs introduce in addition to their excellent fault current-limiting capabilities. The results show that PF improved by 6.7% and 7%, respectively, in simulation and experimental tests. Furthermore, the current THD decreased by 20% and 18% in the simulation and experiment, respectively. [ABSTRACT FROM AUTHOR]

To enhance the reliability of traditional current protection systems in the evolving landscape of future power grids, this paper proposes a differential protection data synchronization approach that leverages satellite and 5G network timing. This method addresses the risk of inadvertent operation due to 5G communication jitter. It employs the BeiDou satellite system for synchronizing the timing of 5G base stations and terminals. This synchronization extends to the 5G terminal and the protection device, thereby mitigating time deviations caused by air interface delays and reducing the 5G network's end-to-end delay by approximately 4 ms on average. A simulation was conducted to assess the reliability and effectiveness of the proposed method under normal satellite signal conditions. The results indicated a significant improvement in protection accuracy, with the method reducing the protection activation time by approximately 5–7 ms compared to the 5G timing data synchronization method. This advancement offers technical support for the safe and stable operation of new power systems. [ABSTRACT FROM AUTHOR]

The complexity of modern power grids, caused by integrating renewable energy sources, especially inverter-based resources, presents a significant challenge to grid operation and planning, since linear models are unable to capture the complex nonlinear dynamics of power systems with coupled muti-scale dynamics, and it necessitate an alternative approach utilizing more advanced and data-driven algorithms to improve modeling accuracy and system optimization. This study employs the sparse identification of nonlinear dynamics method by leveraging compressed sensing and sparse modeling principles, offering robustness and the potential for generalization, allowing for identifying key dynamical features with relatively few measurements, and providing deeper theoretical understanding in the field of power system analysis. Taking advantage of the this method in recognizing the active terms (first and high order) in the system's governing equation, this paper also introduces the novel Volterra-based nonlinearity index to characterize system-level nonlinearity. The distinction of dynamics into first-order linearizable terms, second-order nonlinear dynamics, and third-order noise is adopted to clearly show the intricacy of power systems. The findings demonstrate a fundamental shift in system dynamics as power sources transit to inverter-based resources, revealing system-level (second-order) nonlinearity compared to module-level (first order) nonlinearity in conventional synchronous generators. The proposed index quantifies nonlinear-to-linear relationships, enriching our comprehension of power system behavior and offering a tool for distinguishing between different nonlinearities and visualizing their distinct patterns through the profile of the proposed index. [ABSTRACT FROM AUTHOR]

A large proportion of photovoltaic (PV) power generation is connected to the power grid, and its volatility and stochasticity have significant impacts on the power system. Accurate PV power forecasting is of great significance in optimizing the safe operation of the power grid and power market transactions. In this paper, a novel dual-channel PV power forecasting method based on a temporal convolutional network (TCN) is proposed. The method deeply integrates the PV station feature data with the model computing mechanism through the dual-channel model architecture; utilizes the combination of multihead attention (MHA) and TCN to extract the multidimensional spatio-temporal features between other meteorological variables and the PV power; and utilizes a single TCN to fully extract the temporal constraints of the power sequence elements. The weighted fusion of the dual-channel feature data ultimately yields the ideal forecasting results. The experimental data in this study are from a 26.52 kW PV power plant in central Australia. The experiments were carried out over seven different input window widths, and the two models that currently show superior performance within the field of PV power forecasting: the convolutional neural network (CNN), and the convolutional neural network combined with a long and short-term memory network (CNN_LSTM), are used as the baseline models. The experimental results show that the proposed model and the baseline models both obtained the best forecasting performance over a 1-day input window width, while the proposed model exhibited superior forecasting performance compared to the baseline model. It also shows that designing model architectures that deeply integrate the data input method with the model mechanism has research potential in the field of PV power forecasting. [ABSTRACT FROM AUTHOR]

The aging process of transmission lines has a direct impact on the reliability and safety of the power grid. Therefore, an accurate age estimation method is imperative for effective maintenance planning and infrastructure investment. This paper introduces a systematic methodology for estimating the age of overhead transmission lines, utilizing the percentage statistical health index (%SHI) and the failure probability curve-fitting (FPCF) method. The %SHI, employing a scoring and weighting approach derived from test results and inspections, is used to assess the actual condition of transmission line equipment. Additionally, the FPCF approach is applied to illustrate the connection between the SHI and the likelihood of failure, facilitating the assessment of transmission line age by fitting failure probability curves to the SHI data. This age is directly associated with the probability of experiencing a failure. The evaluation was conducted on 924 towers situated along four transmission lines connecting the 115 kV substations S1–S2, S3–S4, S5–S6, and S7–S8. These transmission lines are in four regions with diverse terrain and environments such as mountains, rice fields, and more. In the SHI calculation, practical testing results and historical failure data were applied. The results clearly indicate that there were notable disparities in the age estimations for transmission lines in diverse geographical regions of Thailand when compared to their actual ages. These discrepancies can be attributed to various factors, including the local environment, such as rainfall, flooding, and salt-laden air as well as specific geographical features like mountainous and coastal terrain. To mitigate the deterioration of transmission lines in all regions, it is essential to implement a proactive maintenance strategy. This strategy should involve more frequent inspections, the use of advanced monitoring technologies, and the establishment of robust maintenance procedures, with which it would become possible to enhance the accuracy of equipment condition assessments, ultimately resulting in an overall improvement in the reliability of transmission lines. [ABSTRACT FROM AUTHOR]

Static compensators (STATCOMs) are often used in distribution systems to enhance power quality. There is a need to enhance the performance of STATCOM to optimize its utilization and facilitate the provision of additional ancillary services. This paper employs the multilayer discrete noise-eliminating second order generalized integrator (MDNESOGI) to regulate the quasi-impedance source inverter (qZSI)-STATCOM for power exchange with the grid. Compared to conventional second-order generalized integrator (SOGI), MDNESOGI exhibits a higher capability for rejecting DC offset. In instances of abnormal grid operation or system malfunction, the inclusion of DC rejection capability enhances the robustness and reliability of the system. The suggested control algorithm only requires two integrators, three mathematical operators, and a damping factor, making it far easier to implement than transformation-based methods. The distorted load current is broken down into its active and reactive components using this control mechanism. The reference currents are then calculated by multiplying these parts by their corresponding voltage standards. The DC offset is reduced and transient oscillations in the weight component are eliminated by adjusting the damping factor. The suggested algorithm effectively handles power quality tasks like (a) reducing harmonic distortion, (b) compensating for reactive power, (c) adjusting for power factor, and (d) balancing the load under different conditions in the distribution system. The experimental study results are used to examine the stability of the proposed control scheme in both static and dynamic scenarios. In addition, a comparison to traditional methods is provided to demonstrate the new method's superiority. Experimentation results show that the suggested controller is superior to its contemporaries in all scenarios where power quality is a factor, meeting the IEEE standard requirements. [ABSTRACT FROM AUTHOR]

The open-circuit fault in electric vehicle charging stations not only impacts the power quality of the electrical grid but also poses a threat to charging safety. Therefore, it is of great significance to study open-circuit fault diagnosis for ensuring the safe and stable operation of power grids and reducing the maintenance cost of charging stations. This paper addresses the multidimensional characteristics of open-circuit fault signals in charging stations and proposes a fault diagnosis method based on an improved S-transform and LightGBM. The method first utilizes improved incomplete S-transform and principal component analysis (PCA) to extract features of front- and back-stage faults separately. Subsequently, LightGBM is employed to classify the extracted features, ultimately achieving fault diagnosis. Simulation results demonstrate the method's effectiveness in feature extraction, achieving an average diagnostic accuracy of 97.04% on the test dataset, along with notable noise resistance and real-time performance. Additionally, we designed an experimental platform for diagnosing open-circuit faults in DC charging station and collected experimental fault data. The results further validate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

High-precision spatial-temporal wind power prediction technology is of great significance for ensuring the safe and stable operation of power grids. The development of artificial intelligence technology provides a new scheme for modeling with strong spatial-temporal correlation. In addition, the existing prediction models are mostly 'black box' models, lacking interpretability, which may lead to a lack of trust in the model by power grid dispatchers. Therefore, improving the model to obtain interpretability has become an important challenge. In this paper, an interpretable short-term wind power prediction model based on ensemble deep graph neural network is designed. Firstly, the graph network model (GNN) with an attention mechanism is applied to the aggregate and the spatial-temporal features of wind power data are extracted, and the interpretable ability is obtained. Then, the long short-term memory (LSTM) method is used to process the extracted features and establish a wind power prediction model. Finally, the random sampling algorithm is used to optimize the hyperparameters to improve the learning rate and performance of the model. Through multiple comparative experiments and a case analysis, the results show that the proposed model has a higher prediction accuracy than other traditional models and obtains reasonable interpretability in time and space dimensions. [ABSTRACT FROM AUTHOR]

The expected increase in electric vehicles necessitates an expansion in charging stations. However, this increase could introduce issues to the power grid, such as the deterioration of voltage stability and an increase in microgrid loading. To address these issues, innovative solutions are imperative. One potential solution is the implementation of charging control mechanisms. This paper analyzes the impact of a residential charging station on a low voltage microgrid from the power quality point of view using a one-year operation simulation. Thirty-seven charging station scenarios with different locations within the network were examined, including instances with no charging control and various combinations involving charging control, photovoltaic power plant, and battery energy storage system. The simulation results of the charging station without charging control show a decrease in some power quality indicators, such as exceeding voltage change thresholds after charging station connection and increasing power losses. On the contrary, the scenarios implementing charging control and local resources effectively mitigate the adverse effects of charging stations on the microgrid. [ABSTRACT FROM AUTHOR]

Due to the high penetration of virtual power plants (VPPs), the bi-directional power flow between VPPs and active distribution grids makes the grid operation complex. Without congestion management, the operation schedule only considers the economic benefits, and power flow constraints might be violated. Hence, it is necessary to conduct power interaction within the operation constraints. This paper proposes a coordinated economic dispatch method under voltage security constraints. The linear expressions were derived by simplifying the AC power flow equations to reduce the computation complicity. Then, optimal economic dispatch models with voltage security constraints were established for the active distribution grid and VPPs, respectively. Meanwhile, the transacted power and clearing price were set as the communication variables, and a coordinated strategy was proposed for the overall optimal goal. The modified IEEE 33-node and PG&E-node distribution grids were utilized for the simulations, and the results affirmed the validity of the proposed method. [ABSTRACT FROM AUTHOR]

This paper presents a methodology developed to perform the processing, analysis, and characterization of AMI measurement data from the substations of three network operators of the Colombian electrical grid. This methodology includes the analysis of the data, which presents the sources of information used by the model, along with the preprocessing and exploratory analysis of the substations data. It also includes the formulation of the data reconstruction method, which uses a constrained optimization model to characterize the substations, based on the different behaviors of the end users of the Colombian electrical grid. In addition to the proposed methodology, the results of its application to the data provided by the operators are provided. These results show the capacity of the proposed methodology to adequately identify the most common behaviors of the users in a given area and characterize most of the energy demand profiles of each substation. [ABSTRACT FROM AUTHOR]

The integration of renewable rnergy sources (RESs) into the power grid involves operational challenges due to the inherent RES energy-production variability. Imbalances between actual power generation and scheduled production can lead to grid instability and revenue loss for RES operators and aggregators. To address this risk, in this paper, we introduce a mutually beneficial bilateral trading scheme between a RES and a DR aggregator to internally offset real-time energy imbalances before resorting to the flexibility market. We consider that the DR aggregator manages the energy demand of users, characterized by uncertainty in their participation in DR events and thus the actual provision of flexibility, subject to their offered monetary incentives. Given that the RES aggregator faces penalties according to dual pricing for positive or negative imbalances, we develop an optimization framework to achieve the required flexibility while addressing the trade-off between maximizing the profit of the RES and DR aggregators and appropriately incentivizing the users. By using appropriate parameterization of the solution, the achievable revenue for the imbalance offsetting can be shared between the RES and the DR aggregators while keeping users satisfied. Our analysis highlights the interdependencies of the demand–production energy imbalance on user characteristics and the RES and DR aggregator profits. Based on our results, we show that a win–win outcome (for the RES and DR aggregators and the users) is possible for a wide range of cases, and we provide guidelines so that such bilateral agreements between RES and DR aggregators could emerge in practical settings. [ABSTRACT FROM AUTHOR]

This document lists some challenges that researchers face when implementing transactive energy in weak power grids. These challenges often include high voltage fluctuations, limited generation, high line loadability, and unbalanced grids. The operation of transactive energy, as well as optimization techniques, are also considered, highlighting the performance and functionalities depending on power grid characteristics and market topology. Some of the most used optimization techniques for market clearing, considering the characteristics and topology, are presented as part of the research work.In addition, this paper compares different market topologies and highlights their advantages and challenges. Furthermore, this paper contains a brief description of the interoperability frameworks applied to a smart grid.As a result, it was determined that interoperability is necessary for the proper functioning of the grid. Moreover, all methods were found to be effective for their purpose from the user's point of view as each technique has different characteristics relevant to the user and the grid. It was concluded that it is convenient to combine the optimization techniques to consider different constraints in the market clearing. [ABSTRACT FROM AUTHOR]

The large-scale centralized development of wind and PV power resources is the key to China's dual carbon targets and clean energy transition. The vast desert–Gobi–wilderness areas in northern and western China will be the best choice for renewable energy development under multiple considerations of resources endowment, land use constraints, technical conditions, and economic level. It is urgent to carry out a quantitative wind and PV resource assessment study in desert–Gobi–wilderness areas. This paper proposed a multi-dimensional assessment method considering the influence of the power grid and transportation infrastructure distributions, which includes three research levels, namely, the technical installed capacity, the development potential, and the development cost. Nine main desert–Gobi–wilderness areas were assessed. The wind and PV technical installed capacities were 0.6 TW and 10.7 TW, and the total development potentials were over 0.12 TW and 1.2 TW, with the full load hours of 2513 and 1759 and the average development costs of 0.28 CNY/kWh and 0.20 CNY/kWh. Finally, this paper proposed the meteorological–electrical division distribution. A case study in the Kubuqi and Qaidam Deserts was carried out on wind–wind and wind–PV collaborative development across different meteorological–electrical divisions, which can reduce by 58% the long-term energy storage capacity and decrease the total system LCOE from 0.488 CNY/kWh to 0.445 CNY/kWh. [ABSTRACT FROM AUTHOR]

The current energy transition combined with the modernization of power systems has provided meaningful transformations in the transmission, distribution, operation, planning, monitoring, and control of power systems. These advancements are heavily dependent on the employment of new computing and communications technologies, which, combined with traditional physical systems, lead to the emergence of cyber–physical systems (CPSs). In this sense, besides the traditional challenges of keeping a reliable, affordable, and safe power grid, one must now deal with the new vulnerabilities to cyberattacks that emerge with the advancement of CPSs. Aware of this perspective and the severity of the ongoing challenges faced by the industry due to cyberattacks, this paper aims to provide a comprehensive survey of the literature on cybersecurity in cyber–physical power systems. For this, clear definitions, historical timelines, and classifications of the main types of cyberattacks, including the concepts, architectures, and basic components that make up, as well as the vulnerabilities in managing, controlling, and protecting, a CPS are presented. Furthermore, this paper presents defense strategies and future trends for cybersecurity. To conduct this study, a careful search was made in relevant academic and industrial databases, leading to a detailed reporting of key works focused on mitigating cyberattacks and ensuring the cybersecurity of modern CPSs. Finally, the paper presents some standards and regulations that technical and international institutions on cybersecurity in smart grids have created. [ABSTRACT FROM AUTHOR]

A new primary frequency controller in power grids undergoing massive wind power penetration is the focus of this paper. The inescapable problem in a largely wind penetrated power grid is to ensure the maintenance of its frequency in the nominal band prescribed by the power system operator (PSO). However, with the massive arrival of wind farms with conventional control schemes, the operation of maintaining and restoring the frequency to the regulatory regimes remains very complicated. In order to overcome the above problem, this paper proposes a new strategy for primary frequency control in power grids using model predictive control (MPC) for a multi-cluster doubly-fed induction generator (DFIG)-based wind farm (WF), with a main objective of reducing the frequency nadir (FN), eliminating the second frequency dip (SFD), and providing the optimal support during wind speed variations. In this approach, a rolling prediction and optimization control strategy is developed based on the dynamic power system model to ideally predict the additional power to be provided. Moreover, in order to avoid second frequency dips, the wind turbines (WTs) are not allocated to extract additional power from the grid during the frequency event, the rotor speeds are not recovered to the maximum power point tracking (MPPT) operating points during the primary frequency control. The performance of the proposed controller was evaluated using a two-zone electrical system in MATLAB/Simulink®. The obtained results disclose that the frequency nadir is enhanced with more than 6.1% compared to the conventional schemes. In addition, the frequency response settling time has been improved with more than 10.51 s. [ABSTRACT FROM AUTHOR]

Local reactive power control in distribution grids with a high penetration of distributed energy resources (DERs) will be essential in future power system operation. Appropriate control characteristic curves for DERs support stable and efficient distribution grid operation. However, the current practice is to configure local controllers collectively with constant characteristic curves that may not be efficient for volatile grid conditions or the desired targets of grid operators. To address this issue, this paper proposes a time series optimization-based method to calculate control parameters, which enables each DER to be independently controlled by an exclusive characteristic curve for optimizing its reactive power provision. To realize time series reactive power optimizations, the open-source tools pandapower and PowerModels are interconnected functionally. Based on the optimization results, Q(V)- and Q(P)-characteristic curves can be individually calculated using linear decision tree regression to support voltage stability, provide reactive power flexibility and potentially reduce grid losses and component loadings. In this paper, the newly calculated characteristic curves are applied in two representative case studies, and the results demonstrate that the proposed method outperforms the reference methods suggested by grid codes. [ABSTRACT FROM AUTHOR]

As the climate crisis worsens, power grids are gradually transforming into a more sustainable state through renewable energy sources (RESs), energy storage systems (ESSs), and smart loads. Virtual power plants (VPP) are an emerging concept that can flexibly integrate distributed energy resources (DERs), managing manage the power output of each DER unit, as well as the power consumption of loads, to balance electricity supply and demand in real time. VPPs can participate in energy markets, enable self-scheduling of RESs, facilitate energy trading and sharing, and provide demand-side frequency control ancillary services (D-FCAS) to enhance the stability of the system frequency. As a result, studies considering VPPs have become the focus of recent energy research, with the purpose of reducing the uncertainty resulting from RESs distributed in the power grid and improving technology related to energy management system (EMS). However, comprehensive reviews of VPPs considering their formation, control techniques, and D-FCAS are still lacking in the literature. Therefore, this paper aims to provide a thorough overview of state-of-the-art VPP technologies for building sustainable power grids in the future. The review mainly considers the development of VPPs, the information transmission and control methods among DERs and loads in VPPs, as well as the relevant technologies for providing D-FCAS from VPPs. This review paper describes the significant economic, social, and environmental benefits of VPPs, as well as the technological advancements, challenges, and possible future research directions in VPP research. [ABSTRACT FROM AUTHOR]

Energy systems around the world are going through tremendous transformations, mainly driven by carbon footprint reductions and related policy imperatives and low-carbon technological development. These transformations pose unprecedented technical challenges to the energy sector, but they also bring opportunities for energy systems to develop, adapt, and evolve. With rising complexity and increased digitalization, there has been significant growth in the amount of data in the power/energy sector (data ranging from power grid to household levels). Utilization of this large data (or "big data"), along with the use of proper data analytics, will allow for useful insights to be drawn that will help energy systems to deliver an increased amount of technical, operational, economic, and environmental benefits. This paper reviews various categories of data available in the current and future energy systems and the potential benefits of utilizing those data categories in energy system planning and operation. This paper also discusses the Big Data Analytics (BDA) that can be used to process/analyze the data and extract useful information that can be integrated and used in energy systems. More specifically, this paper discusses typical applications of BDA in energy systems, including how BDA can be used to resolve the critical issues faced by the current and future energy network operations and how BDA contributes to the development of smarter and more flexible energy systems. Combining data characterization and analysis methods, this review paper presents BDA as a powerful tool for making electrical energy systems smarter, more responsive, and more resilient to changes in operations. [ABSTRACT FROM AUTHOR]

Power flow calculation is the foundation of security analyses in a power system, and the phenomenon of convergence failure is becoming more prominent with the expansion of the power grid. The existing convergence failure diagnosis methods based on optimization modeling and local feature recognition are no longer viable for bulk power systems. This paper proposes a diagnosis method based on intermediate iteration data and the identification of the transmission power congested channel. Firstly, the transmission power congestion index is constructed, and then a method for identifying transmission congestion channels is proposed. The reasons for convergence failure of the power flow are diagnosed from two aspects: excessive power to be transmitted and insufficient transmission capacity. Finally, with the aim of alleviating transmission channel congestion, a correction strategy for power flow injection space data was constructed, which generates relaxation schemes for operational variables. The effectiveness of the proposed strategy was verified using the simulation results of an actual provincial power grid and a standard example power system with 13,659 buses. The method proposed in this paper is entirely based on intermediate power flow iteration data, which avoids the complex modeling of the power flow adjustment and provides methodological support for power flow diagnosis in bulk power systems. [ABSTRACT FROM AUTHOR]

The number of electric vehicles (EVs) is growing exponentially, which presents the power grid with new challenges to turn their reliance to renewable energy sources (RESs). Coordination between the available generations from RESs and the charging time should be managed to optimally utilize the available generation from RESs. The dispatch scheduling of EVs can significantly reduce the impact of these challenges on power systems. Three different technologies can be used to manage the dispatch of EV batteries which are unregulated charging (UC), unidirectional grid-to-vehicle (G2V), and bidirectional vehicle-to-grid (V2G) technologies. This study aims to address the primary reason for EV owners' disbelief in the accuracy of battery wear models, which is impeding their involvement in V2G technology. This paper introduces a novel accurate EV battery wear model considering the instantaneous change in the operation of the EV battery. Moreover, an effective musical chairs algorithm (MCA) is used to reduce everyday expenses and increase revenue for V2G technologies in a short convergence time with accurate determination of optimal power dispatch scheduling. The results obtained from these three strategies are compared and discussed. The salient result from this comparison is that V2G technology increases wear and reduces the battery lifespan in comparison with the UC and G2V. The yearly expenses of G2V are reduced by 33% compared to the one associated with the UC. Moreover, the use of V2G technology provides each EV owner with USD 3244.4 net yearly profit after covering the charging and wear costs. The superior results extracted from the proposed model showed the supremacy of V2G usage, which is advantageous for both EV owners and the power grid. [ABSTRACT FROM AUTHOR]

Due to an increasing demand for electric power and changes in the typology of loads, stability has become a major concern in power systems. As the system stability is directly related to the response of the connected generator, recent research has focused on enhancing generators' stability and improving their response to load variations. This study focuses on adding another excitation winding on to the q-axis, perpendicular to the conventional excitation winding on the d-axis, to control both active and reactive power. This paper studies and compares the performance of the dual excitation synchronous generator (DESG) to conventional synchronous generators. The mathematical equations are derived, and a mathematical model is then developed. The experimental tests have been conducted using a laboratory model consisting of a two-phase synchronous generator driven by a DC motor with different loads. The obtained results and radial diagrams for the different loading types are presented and evaluated. Therefore, a new approach has been designed to connect the DESG directly to the power grid without any electronic components using a special coupling that works in one direction. Two perpendicular excitation coils, d and q, were formed from the existing coils, and the tests were carried out on all loads, ensuring that the revolving angle (i.e., the stability angle φ) was fixed. The results show that the proposed method offers significant cost savings, potentially amounting to 15–20% of the unit price. The experimental results confirm that the DESG significantly improves the generator stability by maintaining a constant rotor angle δ, which requires using an automatic angle regulator (AAR) in addition to the conventional automatic voltage regulator (AVR). [ABSTRACT FROM AUTHOR]

At present, the traditional scheduling mode of power grids generally dispatches according to the power generation cost within the safe range. Transmission costs are evenly distributed to customers according to their load ratios. There are no methods for the rational distribution of transmission costs according to the utilization degree of generation and load to transmission network resources. This traditional scheduling mode will render transmission cost distribution unfair, and it is difficult to guide reasonable load distribution in time and space. Therefore, an optimal economic scheduling method for power systems based on the whole-system-cost electricity price is proposed in this paper. For the power generation and the transmission sides, the whole-system-cost electricity price model was constructed according to the power flow tracking method. For the load side, a demand-side response model of users' responses to electricity price changes was established. Finally, the IEEE 57 node standard model was used to simulate optimal economic scheduling. The results show that the proposed method can guide the rational distribution of power flow. The power flow is shifted moderately from far away to near the power generation center, allowing for the load demand to be guided to meet nearby customers' demands and preventing the line from blocking, the latter of which is conducive to ensuring the safety of the power grid. [ABSTRACT FROM AUTHOR]

In order to solve the problem of randomness and volatility caused by the rapid growth of renewable energy (RE), energy storage systems (ESSs)—as an important means of regulation—can effectively improve the flexible regulation capacity of power systems utilizing a high proportion of RE. Most of the current ESS capacity configuration procedures are carried out based on the typical scenario method or time series production simulation. This method tends to determine the size of the ESS configuration through multiple trial simulations. Uncertainty of simulation prediction data can result in the existence of an excess capacity or lack of configured capacity. In addition, this method reflects the ESS demand under specific targets, but it fails to fully utilize RE generation characteristics. The configuration process lacks the mathematical mechanism of RE consumption, and the calculation process is too complicated. In view of the shortcomings of traditional ESS optimal configuration methods, this paper examines the mathematical mechanism of RE consumption and proposes the ESS optimal configuration analysis method based on "equal area criterion". First, the principle of RE consumption is analyzed and the "RE consumption characteristic curve" is proposed according to RE characteristics. In addition, a working principle diagram of RE consumption, including ESS, is constructed to visually show the consumption capacity of RE and the working position of ESS. Then, the ESS optimal configuration process, based on the "equal area criterion", is proposed to achieve an accurate match between ESS capacity demand and RE consumption targets. Finally, the power grid of a region in China is taken as an example. We prove that the proposed method can save 1.41 × 103 MWh of ESS capacity and provide a more "mathematical" and "convenient" systematic solution for RE consumption and ESS optimization compared to the production simulation method. [ABSTRACT FROM AUTHOR]

The paper presents efficiency and power loss analysis in a high-frequency, seven-level diode-clamped inverter (7LDCB). The inverter is composed of four-level (4L) diode-clamped branches based on MOSFET transistors and Si Schottky diodes. The range of DC-link voltages enables the operation of the inverter in connection with a single-phase power grid. The tested inverter can be controlled using various modulation concepts that affect its parameters, but also energy losses. Carrier-based modulation, which may be useful in a few applications, is compared to selective modulation based on the state machine (SM-based) algorithm. The article demonstrates the efficiency level of the inverter as well as the influence of the modulation method and switching frequency on the efficiency and loss distribution in semiconductor devices. The article also shows the hardware implementation of a complex modulation algorithm based on selective switching states used to maintain voltage balance on three DC-link capacitors. Redundant switching states allow the generation of the same voltage but with the use of a selected DC-link capacitor. This makes it possible to balance the DC-link voltage with the load current. The article presents experimental results, which show the advantage of using the modulation method with selective switching states. First, it allows for equalizing the loading of DC-link capacitors. The second advantage is a more uniform distribution of losses in semiconductor components. [ABSTRACT FROM AUTHOR]

This paper presents an integrated overcurrent relays coordination approach for an Egyptian electric power distribution system. The protection scheme suits all network topologies, including adding distribution generation units (DGs) and creating new paths during fault repair periods. The optimal types, sizes, and locations of DGs are obtained using HOMER software (Homer Pro 3.10.3) and a genetic algorithm (GA). The obtained values align with minimizing energy costs and environmental pollution. The proposed approach maintains dependability and security under all configurations using a single optimum setting for each relay. The calculations consider probable operating conditions, including DGs and fault repair periods. The enhanced coordination procedure partitions the ring into four parts and divides the process into four paths. The worst condition of two cascaded overcurrent relays from the DGs' presence viewpoint is generalized for future work. Moreover, a novel concept addresses the issue of insensitivity during fault repair periods. The performance is validated through the simulation of an Egyptian primary distribution network. [ABSTRACT FROM AUTHOR]

In recent years, with the rapid growth in the number of electric vehicles (EVs), the large-scale grid connection of EVs has had a profound impact on the power grid. As a flexible energy storage resource, EVs can participate in auxiliary services of the power grid via vehicle-to-grid (V2G) technology. Due to the uncertainty of EVs accessing the grid, it is difficult to accurately control their charging and charging behaviors at both the day-ahead and real-time stages. Aiming at this problem, this paper proposes a two-stage scheduling strategy framework for EVs. In the presented framework, according to historical driving data, a day-ahead scheduling model based on distributionally robust optimization (DRO) is first established to determine the total power plan. In the real-time scheduling stage, a real-time scheduling model based on model predictive control (MPC) is established to track the day-ahead power plan. It can reduce the impact of EVs' uncertainties. This strategy can ensure the charging demand of users is under the control of the charging and discharging behaviors of EVs, which can improve the accuracy of controlling EVs. The case study shows that the scheduling strategy can achieve accurate and fast control of charging and discharging. At the same time, it can effectively contribute to the security and stability of grid operations. [ABSTRACT FROM AUTHOR]

Energy storage systems are undergoing a transformative role in the electrical grid, driven by the introduction of innovative frequency response services by system operators to unlock their full potential. However, the limited energy storage capacity of these systems necessitates the development of sophisticated energy management strategies. This paper investigates the newly introduced frequency response service, Dynamic Regulation, within the Great Britain electrical grid. Our study not only establishes control parameters but also demonstrates a novel approach to energy management that pushes the boundaries of the allowable service envelope. We present two distinctive control methods, the first serving as a reference for standard response, and the second as a dynamic control approach, exploiting the extremities of the allowable service envelope. A comprehensive sensitivity analysis that considers availability, the number of equivalent full cycles, and cost–revenue analysis based on grouped dynamic control state of charge setpoints is carried out. Our results underscore that the optimization of average availability takes precedence over merely minimizing the number of cycles, which leads us to define a target state of charge range of between 40% and 45% for a 1-h battery to achieve an availability >95%. Furthermore, our study presents simulated results utilizing real-world frequency data, which reveal the transformative potential of the latter control method. By enhancing the availability of battery energy storage systems, this innovative approach promises not only higher revenues for the asset owner but also assists the system operator in managing frequency. [ABSTRACT FROM AUTHOR]

This paper presents the VCHP platform as a solution to address PV curtailment and line congestion in scenarios of increasing renewable energy penetration. Solar PV generation profiles and load profiles were generated for three scenarios (2025, 2030, and 2035) using data provided by KPX. Modifications were made to the IEEE 30 Bus model to accurately reflect the Korean power system, including the introduction of PCA and LCA at relevant buses. Line congestion was evaluated using metrics such as TUR, STUR, and TLR. The research findings indicate that integrating the VCHP platform in all scenarios effectively alleviates line congestion, as shown by the TUR remaining below 1. Importantly, the reduction in line losses exceeds the decrease in power flow, demonstrating the effectiveness of VCHP in reducing power losses. The results suggest that as renewable energy sources increase, line congestion issues may arise in the existing power system. However, integrating the proposed VCHP platform is a valuable solution for effectively utilizing surplus PV energy and improving the stability of the power grid. The adoption of such a platform can significantly enhance the operation and management of the power system. [ABSTRACT FROM AUTHOR]

Furan tests provide a non-intrusive and cost-effective method of estimating the degradation of paper insulation, which is critical for ensuring the reliability of power grids. However, conducting routine furan tests can be expensive and challenging, highlighting the need for alternative methods, such as machine learning algorithms, to predict furan concentrations. To establish the generalizability and robustness of the furan prediction model, this study investigates two distinct datasets from different geographical locations, Utility A and Utility B. Three scenarios are proposed: in the first scenario, a round-robin cross-validation method was used, with 75% of the data for training and the remaining 25% for testing. The second scenario involved training the model entirely on Utility A and testing it on Utility B. In the third scenario, the datasets were merged, and round-robin cross-validation was applied, similar to the first scenario. The findings reveal the effectiveness of machine learning algorithms in predicting furan concentrations, and particularly the stacked generalized ensemble method, offering a non-intrusive and cost-effective alternative to traditional testing methods. The results could significantly impact the maintenance strategies of power and distribution transformers, particularly in regions where furan testing facilities are not readily available. [ABSTRACT FROM AUTHOR]

Changes are being implemented in the electrical power grid to accommodate the increased penetration of renewable energy sources interfaced with grid-connected inverters. The grid-forming (GFM) control paradigm of inverters in active power grids has emerged as a technique through which to tackle the effects of the diminishing dominance of synchronous generators (SGs) and is preferred to the grid-following (GFL) control for providing system control and stability in converter-dominated grids. Therefore, the development of the GFM control is important as the grid advances towards 100% inverter-based grids. In this paper, therefore, we aim to review the changing grid scenario; the behaviour of grid-connected inverter control paradigms and major GFM inverter controls, including their modifications to tackle low inertia, reduced power quality, fault-ride through capability, and reduced stability; and the state-of-the-art GFM models that are pushing the universality of GFM inverter control. [ABSTRACT FROM AUTHOR]

The traction load of electrified railways is a special user of the power system, which will have a significant impact on and pose a challenge to the power system after grid connection. Considering the impact and fluctuation of traction load connected to the power grid, this paper proposed a method to study the influence of traction load on the transient stability of the power grid based on parameter identification. Firstly, according to the operation characteristics of traction load, a comprehensive traction load model based on the measurement-based method of induction motor parallel power function model is selected, and the objective function of parameter identification is determined. Then, the specific steps of using the improved gray wolf optimizer (IGWO) algorithm to achieve the parameter identification of the traction comprehensive load model are introduced, including chaotic map, nonlinear convergence factor, and individual position update. Next, with the IEEE39 bus system as the network background, the load parameters identified by the measured data of a line of the Beijing–Shanghai high-speed railway are imported into the Power System Analysis Software Package (PSASP) 7.0 for transient simulation to analyze the impact of traction load on the transient stability of the power grid. Finally, three typical load models are compared with the traction load model to draw relevant conclusions, and it is verified that the traction load characteristics are different from the general load model, which provides reference for the connection of electrified railway traction load to the power grid and the economic and technical construction of the power system. [ABSTRACT FROM AUTHOR]

The energy transition hinges on the effective integration of renewable energy sources into the power grid. Islands can provide invaluable insights into the challenges and opportunities of integrating variable renewable energy into the grid due to their relatively small power systems, isolated grids, and diverse availability of renewable energy resources. This paper presents a study on the system benefits and challenges of marine energy integration in insular power systems, focusing on the Orkney Islands as a case study. A microgrid modeling approach that optimizes the mix of renewable sources and energy storage systems for future scenarios considering strategic time horizons (2030, 2040, and 2050) was employed. Results suggest that integrating ocean energies, namely, wave and tidal energy, yields notable benefits compared to traditional renewable energy sources exclusively. These benefits encompass reduced installed capacity, minimized energy storage requirements, lower excess generation, and overall cost-saving. [ABSTRACT FROM AUTHOR]

The negative-sequence current component and harmonic components generated when an asymmetrical fault occurs in the power grid seriously affect the normal operation of the photovoltaic (PV) grid-connected inverter. In order to suppress the negative-sequence current component and the harmonic component of the grid-connected current, and to meet the normal grid-connected operation requirements of the PV grid-connected inverter when asymmetrical faults occur in the grid, this paper proposes the proportional integral double-resonant (PI-DR) current controller, which consists of the PI controller and double-resonant controllers. The PI-DR current controller can directly control the negative-sequence current component and the grid-connected current harmonic component in the output current in the forward synchronous rotating coordinate system, without decomposing the positive and negative sequence currents. The PI-DR current controller ensures that the PV grid-connected inverter can realize normal grid-connected operation and improves the quality of the power when an asymmetrical fault occurs in the power grid. MATLAB/Simulink experiments show that the PI-DR current controller can improve the dynamic characteristics of the PV grid-connected inverter and improve the operating capability of the system when an asymmetrical fault occurs in the power grid. [ABSTRACT FROM AUTHOR]

This paper presents the topology and control of a photovoltaic inverter with an internal battery storage system in conjunction with droop control designed to perform ancillary services such as frequency and reactive power support (voltage regulation), active power dispatch through a proposal to control the charging and discharging of batteries and harmonic current compensation (active filter) in a microgrid connected to an IEEE 13-bus system. The converter in question consists of two stages, a 3-level NPC DC/AC converter and Boost and Buck-Boost DC/DC converters. The system in question is capable of helping to dampen frequency oscillations, as well as regulating the PCC charging curve by charging or discharging the battery bank. In addition, the proposed system is capable of supplying reactive power to the grid on a permanent basis, thus helping with voltage control. It is also capable of compensating for harmonic currents caused by non-linear loads connected to the PCC. In this context, we can see the multifunctionality of the photovoltaic inverter in helping to mitigate disturbances associated with the power quality, with the differential of charge and discharge control to preserve the useful life of the energy storage system. For this study, Matlab/Simulink software was used to implement and validate the proposed topology and control systems. In the computer simulations carried out, satisfactory results were obtained in relation to the execution of the ancillary services mentioned above, thus demonstrating the viability of the proposed strategy. [ABSTRACT FROM AUTHOR]

Grid-forming converters are considered a key technology for electrical grids with a high share of renewable energy. However, there is a lack of a general, robust and verifiable definition of what constitutes this behaviour. Therefore, this paper presents three simple scenarios that enable such a definition. They are based on simple black-box simulations that allow manufacturers to protect their development work. It can be shown that grid forming can be clearly distinguished from grid-following controls by their grid behaviour in the proposed scenarios. Extensive results illustrate this and also provide suggestions to deepen the understanding of grid-forming grid behaviour and its impact on system inertia. These findings should inspire the development of a clear definition and ultimately new requirements for converter systems. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) systems are a clean energy source that allows for power generation integration into electrical networks without destructive environmental effects. PV systems are usually integrated into electrical networks only to provide active power during the day, without taking full advantage of power electronics devices, which can compensate for the reactive power at any moment during their operation. These systems can also generate dynamic reactive power by means of voltage source converters, which are called PV-STATCOM devices. This paper presents a convex formulation for the optimal integration (placement and sizing) of PV-STATCOM devices in electrical distribution systems. The proposed model considers reducing the costs of the annual energy losses and installing PV-STATCOM devices. A convex formulation was obtained to transform the hyperbolic relation between the products of the voltage into a second-order constraint via relaxation. Two simulation cases in the two IEEE test systems (33- and 69-node) with radial and meshed topologies were implemented to demonstrate the effectiveness of the proposed mixed-integer convex model. The results show that PV-STATCOM devices reduce the annual cost of energy losses of electrical networks in a more significant proportion than PV systems alone. [ABSTRACT FROM AUTHOR]

Currently, most of the series inverter control methods rely on communication, which greatly reduces the reliability of the system and increases the cost. To address the above problems, this paper proposes a decentralized control strategy for series-connected single-phase two-stage grid-connected photovoltaic (PV) inverters. By improving the traditional droop control, the frequency and phase of the output voltage of each inverter unit are consistent and self-synchronized with the power grid while relying only on local independent control, and each unit realizes maximum power point tracking (MPPT). At different light intensities, each series-connected unit can quickly track the new maximum power point while still maintaining self-synchronization between the units. The system stability is analyzed via the small signal method, and sufficient conditions for system stability are obtained. Finally, the simulation results verify the correctness and effectiveness of the proposed control strategy. [ABSTRACT FROM AUTHOR]

The problem of estimating the deterministic susceptibility coefficient of electronic components to standardised types of electromagnetic disturbance has been presented in this paper. From a theoretical point of view, the problem of damage to electronic elements is presented with the impact of disturbances of critical values on them and the potential impact of this effect on the reliability of the element and ultimately the system or electronic device. For a selected exemplary electronic component, a method for estimating the susceptibility coefficient according to the developed methodology is discussed. Experimental tests were carried out by exposing the test component to a standardised surge of 1.2/50 μs which was observed in an electrical grid. In order to illustrate the developed method, aimed at describing the immunity of an electronic component to a standardised type of disturbance, a signal diode was selected for testing. Using this element as an example, it is shown how, using statistical techniques, the coefficient of its susceptibility to a specific type of disturbance can be estimated. [ABSTRACT FROM AUTHOR]

The employment of input filters in modern DC–DC converters is mandatory in order to ensure EMC (Electro-Magnetic Compatibility), provide power electronics with decent voltage and minimize the converter influence on the power grid. The LC type input filters bring also a possibility of voltage and current oscillation that may occur in the system. This oscillation may rise to a certain level that affects system stability. A wide range of methods are employed in order to attenuate these oscillations and allow appropriate system transient response. In this paper, the sliding mode control (SMC) strategy is proposed to reduce the input LC filter voltage and current oscillation and allow DC (Direct Current) output voltage control for both resistive and constant power load. The proposed control algorithm is intended for use in railway, tram and trolleybus DC/DC converters. For the proposed scheme of control simulation, a model is developed using Simulink software. Furthermore, laboratory stand experiments are carried out to verify simulation results. [ABSTRACT FROM AUTHOR]

The widespread adoption of electric vehicles (EVs) poses challenges associated with charging infrastructures and their impact on the electrical grid. To address these challenges, smart charging approaches have emerged as a key solution that optimizes charging processes and contributes to a smarter and more efficient grid. This paper presents an innovative multi-objective optimization framework for EV smart charging (EVSC) using the Dynamic Hunting Leadership (DHL) method. The framework aims to improve the voltage profile of the system in addition to eliminating voltage violations and energy not supplied (ENS) to EVs within the network. The proposed approach considers both residential EV chargers and parking stations, incorporating realistic EV charger behaviors based on constant current charging and addressing the problem as a mixed integer non-linear programming (MINLP) problem. The performance of the optimization method is evaluated on a distribution network with varying levels of EV penetration connected to the chargers in the grid. The results demonstrate the effectiveness of the DHL algorithm in minimizing conflicting objectives and improving the grid's voltage profile while considering operational constraints. This study provides a road map for EV aggregators and EV owners, guiding them on how to charge EVs based on preferences while minimizing adverse technical impacts on the grid. [ABSTRACT FROM AUTHOR]

Nowadays, the penetration of inverter-based energy resources is continuously increasing in low-voltage distribution grids. Their applications cover traditional renewable energy production and energy storage but also new applications such as charging points for electric vehicles, heat pumps, electrolyzers, etc. The power ratings range from a couple of kW to hundreds of kW. Utilities have, in the last few years, reported more challenges regarding power quality in distribution grids, e.g., high harmonic content, high unbalances, large voltage and frequency excursions, etc. Phase-Lock-Loop (PLL) algorithms are typically used for grid synchronization and decoupled control of power converters connected to the grid. Most of the research within PLLs is mainly focusing on grid voltage angle estimation while the byproducts of the algorithms, e.g., frequency and voltage magnitude, are often overlooked. However, both frequency and voltage magnitude estimations are crucial for grid code compliance. Practical considerations for implementation on microcontroller boards of these algorithms are also missing in most of the cases. The present paper proposes a modified PLL algorithm based on a Synchronous Reference Frame that is suitable for both grid synchronization and frequency monitoring, i.e., the estimation of RMS phase voltages and frequencies in highly distorted distribution grids. It also provides the tuning methodology and practical considerations for implementation on commercial DSP boards. The performance of the proposed approach is assessed through simulation studies and laboratory tests under a wide range of operational conditions, showing that the proposed PLL can estimate the grid frequency, for all considered grid events, with an accuracy of less than ±5 mHz, which is a significant improvement on the current state-of-the-art solutions, having an accuracy of at least ±20 mHz or more. [ABSTRACT FROM AUTHOR]

Virtual power plants (VPPs) offer a feasible solution for integrating various types of distributed energy resources (DERs) into the power grid in the electricity market. This paper proposes a multi-time-scale rolling optimal scheduling for VPPs, enabling optimal self-scheduling plans across intra-week rolling scheduling, intra-day rolling dispatch, and real-time dispatch. The proposed method facilitates participation in energy and flexible ramping product (FRP) markets while considering the specific characteristics with complementary advantages for the aggregated renewable resources, gas turbines, energy storages, and flexible demands of each time scale. The flexible ramping products within the VPP framework are established, while the energy storage systems address fluctuations during dispatch periods. Case studies are conducted to verify the efficiency of the proposed method. The results show that the proposed method can obtain optimal self-scheduling plans within the multi-time framework and has better performance in economy and security operation in comparisons among cases. [ABSTRACT FROM AUTHOR]

The output of wind power and photovoltaic power is random, fluctuating and intermittent, and a direct grid connection will result in the reduction of power generation income and a great fluctuation in the power grid's connection. The addition of hydropower stations can reduce the above problems. Therefore, this paper first introduces and analyzes a typical application scenario of a water–wind–light combined power generation system. Then, a multi-objective optimization model is established, considering the two objectives of maximizing the joint generation and minimizing the system's power fluctuation. Third, the adaptive fractional order calculus strategy is introduced, and a multi-objective pigeon swarm algorithm, which can adaptively adjust the fractional order according to the location information of a flock, is proposed. Finally, an optimization simulation is carried out. The simulation results show that the improved multi-objective pigeon swarm algorithm has better optimization accuracy. It provides a reference for the future implementation of hydropower stations, and the surrounding wind and photoelectric field joint dispatching strategy. [ABSTRACT FROM AUTHOR]

This paper deals with the reduction in electrical losses and the minimization of voltage deviation in electrical power grids. To this end, a novel heuristic-based approach is proposed for controlling reactive power injections along an electrical grid with distributed generation using distributed photovoltaic (PV) generation. The proposed approach consists of applying a heuristic, namely a genetic or firefly algorithm, to solve the loss and voltage deviation optimization problem by controlling PV reactive power injections. The proposed method was tested on a radial 100-bus network with an intense penetration of PV generation. The obtained results indicate that the proposed method consistently yields superior grid performance when compared to algorithms previously proposed in the literature. In fact, it led to a reduction in the active power supplied by the reference bus to the grid, thereby alleviating the burden imposed on the most upstream parts of the distribution network. As a consequence, the proposed method contributes to a power-efficient network, enhancing its loss performance and voltage stability. [ABSTRACT FROM AUTHOR]

With the increasing integration of HVDC tie-lines, the regional power systems in both the energy-exporting area and the energy-importing area have been gradually evolving into "strong DC, weak AC" systems. In this paper, a multi-period transmission expansion planning optimization model is proposed for an energy-exporting power grid with hybrid AC/DC interface. While the existing literature has not considered the dynamic security problem in TEP, this paper adopts the conventional total transfer capacity (TTC) index to evaluate the security limit of hybrid AC/DC interface under different transmission expansion schemes. Multiple objectives are considered to reduce the investment cost while promoting the consumption of renewables by enhancing the total transfer capacity of hybrid AC/DC interface. The non-dominated sorting genetic algorithm-II (NSGA-II) is used to compute the optimal solution for the proposed multi-period multi-objective transmission expansion planning problem. A case study on the modified IEEE 39-bus system is presented to demonstrate the effectiveness of the proposed method. [ABSTRACT FROM AUTHOR]

Asynchronous loads (AL), because of their low negative-sequence resistance, produce the effect of reduced unbalance at their connection points. Therefore, proper modeling of unbalanced load flows in power supply systems requires properly accounting for AL. Adequate models of the induction motor can be realized in the phase frame of reference. The effective use of such models is possible only if accurate data on the parameters of induction motor equivalent circuits for positive and negative sequences are available. Our analysis shows that the techniques used to determine these parameters on the basis of reference data can yield markedly disparate results. It is possible to overcome this difficulty by applying parameter identification methods that use the phase frame of reference. The paper proposes a technique for parameter identification of models of individual induction motors and asynchronous load nodes. The results of computer-aided simulation allow us to conclude that by using parameter identification, we can obtain an equivalent model of an asynchronous load node, and such a model provides high accuracy for both balanced and unbalanced load flow analysis. By varying load flow parameters, we demonstrate that the model proves valid over a wide range of their values. We have proposed a technique for the identification of asynchronous load nodes with such asynchronous loads, including electrical drives equipped with static frequency converters. With the aid of the AL identification models proposed in this paper, it is possible to solve the following practical tasks of management of electric power systems: increasing the accuracy of modeling their operating conditions; making informed decisions when taking measures to reduce unbalance in power grids while accounting for the balancing adjustment effect of AL. [ABSTRACT FROM AUTHOR]

At present, in the situation that wind power penetration is increasing year by year, the use of a hybrid energy storage system (HESS) to smooth out wind power fluctuations becomes an effective method. However, the existing control strategy has the problem of inadequate utilization of fluctuating power. In this paper, we propose a control strategy for smoothing wind power fluctuations based on double Kalman filters with adaptive adjustment of the state of charge (SOC). Firstly, considering the wind power's active power grid constraint, the parameters of the dual Kalman filter are adaptively adjusted according to the original output power to obtain the target grid power synchronously, and the total smoothing command of the energy storage system is determined with the goal of improving the SOC of the lithium battery. On this basis, the SOC of the supercapacitor is considered to be improved, and the adaptive low-pass filter is used for the secondary distribution of the energy storage power command to achieve fine-grained management of the output power of HESS. The final simulation results show that the obtained smoothed wind power satisfies the 1 min and 10 min fluctuation criteria, and the minimum capacity required for lithium batteries is reduced by 0.07 MW·h under the same initial conditions as in the proposed method in this paper; it can use the fluctuating power when the SOC crosses the limit, and has a regulating effect on the SOC of HESS to improve the wind power smoothing ability and realize the stable grid-connection requirement of wind power. [ABSTRACT FROM AUTHOR]

Solar power forecasting is of high interest in managing any power system based on solar energy. In the case of photovoltaic (PV) systems, and building integrated PV (BIPV) in particular, it may help to better operate the power grid and to manage the power load and storage. Power forecasting directly based on PV time series has some advantages over solar irradiance forecasting first and PV power modeling afterwards. In this paper, the power forecasting for BIPV systems in a vertical façade is studied using machine learning algorithms based on decision trees. The forecasting scheme employs the skforecast library from the Python environment, which facilitates the implementation of different schemes for both deterministic and probabilistic forecasting applications. Firstly, deterministic forecasting of hourly BIPV power was performed with XGBoost and Random Forest algorithms for different cases, showing an improvement in forecasting accuracy when some exogenous variables were used. Secondly, probabilistic forecasting was performed with XGBoost combined with the Bootstrap method. The results of this paper show the capabilities of Random Forest and gradient boosting algorithms, such as XGBoost, to work as regressors in time series forecasting of BIPV power. Mean absolute error in the deterministic forecast, using the most influencing exogenous variables, were around 40% and close below 30% for the south and east array, respectively. [ABSTRACT FROM AUTHOR]

Achieving clean energy goals will require significant advances in regard to addressing the computational needs for next-generation renewable-dominated power grids. One critical obstacle that lies in the way of transitioning today's power grid to a renewable-dominated power grid is the lack of a faster-than-real-time stability assessment technology for operating a fast-changing power grid. This paper proposes an artificial intelligence (AI) -based method that predicts the system's stability margin information (e.g., the frequency nadir in the frequency stability assessment and the critical clearing time (CCT) value in the transient stability assessment) directly from the system operating conditions without performing the conventional time-consuming time-domain simulations over detailed dynamic models. Since the AI method shifts the majority of the computational burden to offline training, the online evaluation is extremely fast. This paper has tested the AI-based stability assessment method using multiple dispatch cases that are converted and tuned from actual dispatch cases of the Western Electricity Coordinating Council (WECC) system model with more than 20,000 buses. The results show that the AI-based method could accurately predict the stability margin of such a large power system in less than 0.2 milliseconds using the offline-trained AI agent. Therefore, the proposed method has great potential to achieve faster-than-real-time stability assessment for practical large power systems while preserving sufficient accuracy. [ABSTRACT FROM AUTHOR]