Search

Lot scale rainwater tank system modeling is often used in sustainable urban storm water management, particularly to estimate the reduction in the storm water run-off and pollutant wash-off at the lot scale. These rainwater tank models often cannot be adequately calibrated and validated due to limited availability of observed rainwater tank quantity and quality data. This paper presents calibration and validation of a lot scale rainwater tank system model using XP-SWMM utilizing data collected from two rainwater tank systems located in Western Sydney, Australia. The modeling considers run-off peak and volume in and out of the rainwater tank system and also a number of water quality parameters (Total Phosphorus (TP), Total Nitrogen (TN) and Total Solids (TS)). It has been found that XP-SWMM can be used successfully to develop a lot scale rainwater system model within an acceptable error margin. It has been shown that TP and TS can be predicted more accurately than TN using the developed model. In addition, it was found that a significant reduction in storm water run-off discharge can be achieved as a result of the rainwater tank up to about one year average recurrence interval rainfall event. The model parameter set assembled in this study can be used for developing lot scale rainwater tank system models at other locations in the Western Sydney region and in other parts of Australia with necessary adjustments for the local site characteristics. [Copyright &y& Elsevier]

Rainwater tanks are increasingly adopted in Australia to reduce potable water demand and are perceived to reduce the volume of stormwater discharge from developments. This paper investigates the water balance of rainwater tanks, in particular the possible impacts these tanks could have in controlling the stormwater discharge volume. The study collected water quantity data from two sites in the Hawkesbury City Council area, New South Wales, Australia and utilised the collected data in a simple water balance model to assess the effectiveness of rainwater tanks in reducing the stormwater discharge volume. The results indicate that a significant reduction in discharge volume from a lot scale development can be achieved if the rainwater tank is connected to multiple enduses, but is minimal when using irrigation alone. In addition, the commonly used volumetric runoff coefficient of 0.9 was found to over-estimate the runoff from the roof areas and to thereby underestimate the available volume within the rainwater tanks for retention or detention. Also, sole reliance on the water in the rainwater tanks can make the users aware of their water use pattern and water availability, resulting in significant reductions in water use as the supply dwindles, through self imposed water restrictions. [ABSTRACT FROM AUTHOR]

Abstract: Due to greater environmental awareness and mandatory water restrictions in many Australian cities, rainwater tanks have become popular in recent years. This paper investigates the water savings potential of rainwater tanks fitted in detached houses at 10 different locations in Greater Sydney, Australia. A water balance simulation model on daily time scale is developed and water savings, reliability and financial viability are examined for three different tank sizes, 2kL, 3kL and 5kL. It is found that the average annual water savings from rainwater tanks are strongly correlated with average annual rainfall. It is also found that the benefit cost ratios for the rainwater tanks are smaller than 1.00 without government rebate. It is noted that a 5kL tank is preferable to 2kL and 3kL tanks and rainwater tanks should be connected to toilet, laundry and outdoor irrigation to achieve the best financial outcome for the home owners. The results from this study suggest that government authorities in Sydney should maintain or possibly increase the rebate for rainwater tanks to enhance its acceptance. [Copyright &y& Elsevier]

Rainwater harvesting (RWH) has become a popular water saving and conservation means across the globe. In many cities, a pre-determined rainwater tank size is generally selected without a detail water balance modelling at the location on interest. However, to achieve maximum benefit from a RWH system at a given location, it is desirable to design the system based on the site specific conditions (e.g. local rainfall and loss characteristics) and other relevant design parameters. There have been limited studies on regionalization of RWH system, which can account for the spatial variability in rainfall, loss and water demand characteristics over a given region to provide site-specific design of RWH system. This paper presents a RWH regionalization approach to develop a set of design curves, which assist in the selection of an adequate RWH system at a given location. We use rainfall data from 159 rain gauges across the Greater Sydney region in Australia to develop and test the proposed regionalization approach. It has been found that there is a significant variation in rainfall characteristics across Greater Sydney region and that a common tank size across this region does not present an adequate solution. It has been found that a 5 kL tank can achieve a reliability (i.e. percentage of days the RWH can meet the given demand) of 31–93% for four people depending on the location in the Greater Sydney region and the types of water use. The developed regional design curves could result in increased water savings across Greater Sydney. The proposed regionalization approach can be adapted to other cities across Australia and the world which present a high rainfall gradient. • Water savings by rainwater harvesting at 159 locations in Sydney are evaluated. • Reliability of a rainwater tank is moderately correlated with mean annual rainfall. • A set of design curves is developed for Sydney to enhance rainwater harvesting. [ABSTRACT FROM AUTHOR]