Search

The development of diagnostic tools for measuring a wide spectrum of target analytes, from biomarkers to other biochemical parameters in biological fluids, has experienced a significant growth in the last decades, with a good number of such tools entering the market. Recently, a clear focus has been put on miniaturized wearable devices, which offer powerful capabilities for real-time and continuous analysis of biofluids, mainly sweat, and can be used in athletics, consumer wellness, military, and healthcare applications. Sweat is an attractive biofluid in which different biomarkers could be noninvasively measured to provide rapid information about the physical state of an individual. Wearable devices reported so far often provide discrete (single) measurements of the target analytes, most of them in the form of a yes/no qualitative response. However, quantitative biomarker analysis over certain periods of time is highly demanded for many applications such as the practice of sports or the precise control of the patient status in hospital settings. For this, a feasible combination of fluidic elements and sensor architectures has been sought. In this regard, this paper shows a concise overview of analytical tools based on the use of capillary-driven fluidics taking place on paper or fabric devices integrated with solid-state sensors fabricated by thick film technologies. The main advantages and limitations of the current technologies are pointed out together with the progress towards the development of functional devices. Those approaches reported in the last decade are examined in detail.

The fabrication of low-cost, flexible, and recyclable electronic devices has been the focus of many research groups, particularly for integration in wearable technology and the Internet of Things (IoT). In this work, porous zinc oxide (ZnO) nanostructures are incorporated as a UV sensing material into the composition of a sustainable water-based screen-printable ink composed of car-boxymethyl cellulose (CMC). The formulated ink is used to fabricate flexible and foldable UV sensors on ubiquitous office paper. The screen-printed CMC/ZnO UV sensors operate under low voltage (≤2 V) and reveal a stable response over several on/off cycles of UV light exposure. The devices reach a response current of 1.34 ± 0.15 mA and a rise and fall time of 8.2 ± 1.0 and 22.0 ± 2.3 s, respectively. The responsivity of the sensor is 432 ± 48 mA W−1, which is the highest value reported in the literature for ZnO-based UV sensors on paper substrates. The UV-responsive devices display impressive mechanical endurance under folding, showing a decrease in responsivity of only 21% after being folded 1000 times. Their low-voltage operation and extreme folding stability indicate a bright future for low-cost and sustainable flexible electronics, showing potential for low-power wearable applications and smart packaging. publishersversion published

Paper waste in the mockups design with regular, irregular, and amorphous patterns is a critical problem in digital printing presses. Paper waste reduction directly impacts production costs, generating business and environmental benefits. This problem can be mapped to the two-dimensional irregular bin-packing problem. In this paper, an iterated local search algorithm using a novel neighborhood structure to detect overlaps between amorphous shapes is introduced. This algorithm is used to solve the paper waste problem, modeled as one 2D irregular bin-packing problem. The experimental results show that this approach works efficiently and effectively to detect and correct the overlaps between regular, irregular, and amorphous figures.

Despite the potential in fabrication of microfluidic paper-based analytical devices (μPADs) for point-of-care testing (POCT) kits, the development of simple, accurate, and rapid devices with higher sensitivity remains challenging. Here, we report a novel method for 3D-μPAD fabrication with enclosed channels using vat photopolymerization to avoid fluid evaporation. In detail, height of the enclosed channels was adjusted from 0.3 to 0.17 mm by varying the UV exposure time from 1 to 4 s for the top barrier, whereas the exposure time for the bottom and side barriers was fixed. As a result, sample flow in the enclosed channels of 3D-μPADs showed lesser wicking speed with very scant evaporation compared to that in the hemi channels in the 3D-μPADs. The stoppage of evaporation in the enclosed channels significantly improved the gray intensity and uniformity in the detection zone of the 3D-μPADs, resulting in as low as 0.3 mM glucose detection. Thus 3D-μPADs with enclosed channels showed enhanced sensitivity compared to the 3D-μPADs with hemi channels when dealing with a small volume sample. Our work provides a new insight into 3D-μPAD design with enclosed channels, which redefines the methodology in 3D printing.

This review summarizes the state of the art of paper-based biosensors (PBBs) for coronavirus disease 2019 (COVID-19) detection. Three categories of PBB are currently being been used for severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) diagnostics, namely for viral gene, viral antigen and antibody detection. The characteristics, the analytical performance, the advantages and drawbacks of each type of biosensor are highlighted and compared with traditional methods. It is hoped that this review will be useful for scientists for the development of novel PBB platforms with enhanced performance for helping to contain the COVID-19 outbreak, by allowing early diagnosis at the point of care (POC).

An origami three-dimensional design of a paper-based potentiometric sensor is described. In its simplest form, this electrochemical paper-based analytical device (ePAD) is made from three small parts of the paper. Paper layers are folded on each other for the integration of a solid contact ion selective electrode (here a carbon-paste composite electrode) and a solid-state pseudo-reference electrode (here writing pencil 6B on the paper), which are in contact with a hydrophilic channel fabricated on the middle part (third part) of the paper. In this case, the pseudo-reference and working electrodes are connected to the two sides of the hydrophilic channel and hence the distance between them is as low as the width of paper. The unmodified carbon paste electrode (UCPE) and modification with the crown ether benzo15-crown-5 (B15C5) represented a very high sensitivity to Cu (II) and Cd2+ ions, respectively. The sensor responded to H2O2 using MnO2-doped carbon paste electrode (CPE). Furthermore, a biosensor was achieved by the addition of glucose oxidase to the MnO2-doped CPE and hence made it selective to glucose with ultra-sensitivity. In addition to very high sensitivity, our device benefits from consuming a very low volume of sample (10.0 µL) and automatic sampling without need for sampling devices.

Paper-based microfluidic devices are an attractive platform for developing low-cost, point-of-care diagnostic tools. As paper-based devices&rsquo, detection chemistries become more complex, more complicated devices are required, often entailing the sequential delivery of different liquids or reagents to reaction zones. Most research into flow control has been focused on introducing delays. However, delaying the flow can be problematic due to increased evaporation leading to sample loss. We report the use of a CO2 laser to uniformly etch the surface of the paper to modify wicking speeds in paper-based microfluidic devices. This technique can produce both wicking speed increases of up to 1.1&times, faster and decreases of up to 0.9&times, slower. Wicking speeds can be further enhanced by etching both sides of the paper, resulting in wicking 1.3&times, faster than unetched channels. Channels with lengthwise laser-etched grooves were also compared to uniformly etched channels, with the most heavily grooved channels wicking 1.9&times, faster than the fastest double-sided etched channels. Furthermore, sealing both sides of the channel in packing tape results in the most heavily etched channels, single-sided, double-sided, and grooved, wicking over 13&times, faster than unetched channels. By selectively etching individual channels, different combinations of sequential fluid delivery can be obtained without altering any channel geometry. Laser etching is a simple process that can be integrated into the patterning of the device and requires no additional materials or chemicals, enabling greater flow control for paper-based microfluidic devices.

In this study, the effects of the mixing conditions of waste paper sludge ash (WPSA) on the strength and bearing capacity of controlled low-strength material (CLSM) were evaluated, and the optimal mixing conditions were used to evaluate the strength characteristics of CLSM with recyclable WPSA. The strength and bearing capacity of CLSM with WPSA were evaluated using unconfined compressive strength tests and plate bearing tests, respectively. The unconfined compressive strength test results show that the optimal mixing conditions for securing 0.8&ndash, 1.2 MPa of target strength under 5% of cement content conditions can be obtained when both WPSA and fly ash are used. This is because WPSA and fly ash, which act as binders, have a significant impact on overall strength when the cement content is low. The bearing capacity of weathered soil increased from 550 to 575 kPa over time, and CLSM with WPSA increased significantly, from 560 to 730 kPa. This means that the bearing capacity of CLSM with WPSA was 2.0% higher than that of weathered soil immediately after construction, furthermore, it was 27% higher at 60 days of age. In addition, the allowable bearing capacity of CLSM corresponding to the optimal mixing conditions was evaluated, and it was found that this value increased by 30.4% until 60 days of age. This increase rate was 6.7 times larger than that of weathered soil (4.5%). Therefore, based on the allowable bearing capacity calculation results, CLSM with WPSA was applied as a sewage pipe backfill material. It was found that CLSM with WPSA performed better as backfill and was more stable than soil immediately after construction. The results of this study confirm that CLSM with WPSA can be utilized as sewage pipe backfill material.

In the age of Evidence-Based Medicine, Clinical Guidelines (CGs) are recognized to be an indispensable tool to support physicians in their daily clinical practice. Medical Informatics is expected to play a relevant role in facilitating diffusion and adoption of CGs. However, the past pioneering approaches, often fragmented in many disciplines, did not lead to solutions that are actually exploited in hospitals. Process Mining for Healthcare (PM4HC) is an emerging discipline gaining the interest of healthcare experts, and seems able to deal with many important issues in representing CGs. In this position paper, we briefly describe the story and the state-of-the-art of CGs, and the efforts and results of the past approaches of medical informatics. Then, we describe PM4HC, and we answer questions like how can PM4HC cope with this challenge? Which role does PM4HC play and which rules should be employed for the PM4HC scientific community? This research received no external funding

Humidity sensors are indispensable for various electronic systems and instrumentations. To develop a new humidity sensing mechanism is the key for the next generation of sensor technology. In this work, a novel flexible paper-based current humidity sensor is proposed. The developed alternating current electroluminescent devices (ACEL) consist of the electroless plating Ni on filter paper and silver nanowires (AgNWs) as the bottom and upper electrodes, and ZnS:Cu as the phosphor layer, respectively. The proposed humidity sensor is based on ACEL with the paper substrate and the ZnS:Cu phosphor layer as the humidity sensing element. The moisture effect on the optical properties of ACELs has been studied firstly. Then, the processing parameters of the paper-based ACELs such as electroless plated bottom electrode and spin-coated phosphor layer as a function of the humidity-sensitive characteristics are investigated. The sensing mechanism of the proposed sensor has been elucidated based on the Q ~ V analysis. The sensor exhibits an excellent linearity ( R 2 = 0.99965 ) within the humidity range from 20% to 90% relative humidity (RH) and shows excellent flexibility. We also demonstrate its potential application in postharvest preservation where the EL light is used for preservation and the humidity can be monitored simultaneously through the current.

Environmental concerns and soaring energy prices have brought huge pressure of energy saving and emission reduction to tissue paper mills. Electricity is one of the main energy sources of tissue paper mills. The production characteristics of tissue paper mills make it easy to decrease energy cost by using time-of-use (TOU) electricity tariffs. This study investigates the bi-objective energy-efficiency scheduling of tissue paper mills under time-of-use electricity tariffs, the objectives of which are makespan and energy cost. First, considering the processing energy cost, setup energy cost, and transportation energy cost, an energy cost model of a tissue paper mill under TOU electricity tariffs is established. Second, the energy-efficiency scheduling model under TOU electricity tariffs is built based on the energy cost model. Finally, on the basis of decomposition and teaching&ndash, learning optimization, this study proposes a novel multi-objective evolutionary algorithm and further combined with the variable neighborhood search to solve the problem. The case study results demonstrate that our study of tissue paper mill energy saving is feasible, and the proposed method has better performance than the existing methods.

Humanity is facing some major global threats, namely lack of environmental sustainability, the energy crisis associated with the unsustainable reliance on fossil fuels, and water scarcity, which will be exacerbated with the rapid growth of urban areas. Researchers have drawn their attention to microalgae, photosynthetic microorganisms known for their environmental applications, such as wastewater remediation and lipids accumulation, to produce third-generation biofuels to solve some of these major issues. Considering this dual role, this study evaluated the potential of the microalga Chlorella vulgaris on nutrient removal from a paper industry effluent and bioenergy production. Firstly, experiments were performed to assess the potential of this microalga to: (i) successfully grow in different concentrations of a paper industry effluent (20% to 100%), and (ii) treat the industrial effluent, reducing phosphorus concentrations to values below the accepted legal limits. Then, a techno-economic assessment was performed to study the viability of a C. vulgaris biorefinery targeting the remediation of a paper industry effluent and bioenergy production. The results have shown that C. vulgaris was able to successfully grow and treat the paper industry effluent. Under these conditions, average biomass productivities determined for this microalga ranged between 15.5 &plusmn, 0.5 and 26 &plusmn, 1 mg dry weight (DW) L&minus, 1 d&minus, 1, with maximum biomass concentrations reaching values between 337 &plusmn, 9 and 495 &plusmn, 25 mg DW L&minus, 1. Moreover, final phosphorus concentrations ranged between 0.12 &plusmn, 0.01 and 0.5 &plusmn, 0.3 mg P L&minus, 1, values below the legal limits imposed by the Portuguese Environment Agency on the paper industry. Regarding the proposal of a microalgal biorefinery for the bioremediation of paper industry effluents with bioenergy production, the techno-economic study demonstrated that six of the seven studied scenarios resulted in an economically-viable infrastructure. The highest net present value (15.4 million euros) and lowest discounted payback period (13 years) were determined for Scenario 3, which assumed a photosynthetic efficiency of 3%, a lipids extraction efficiency of 75%, and an anaerobic digestion efficiency of 45%. Therefore, it was possible to conclude that besides being economically viable, the proposed biorefinery presents several environmental benefits: (i) the remediation of an industrial effluent, (ii) CO2 uptake for microalgal growth, which contributes to a reduction in greenhouse gases emissions, (iii) production of clean and renewable energy, (iv) soil regeneration, and (v) promotion of a circular economy.

Development of paper-based sensors that do not suffer with humidity interference is desirable for practical environmental applications. In this work, a laser processing method was reported to effectively modulate the cross-sensitivity to humidity of ZnO-based UV (Ultraviolet) sensors printed on paper substrate. The results reveal that the laser induced zinc oxide (ZnO) surface morphology contributes to the super-hydrophobicity of the printed ZnO nanoparticles, reducing humidity interference while enhancing UV sensitivity. Herein, this conducted research highlights for the first time that laser processing is an attractive choice that reduces the cross-sensitivity to water vapor in the UV sensing response of ZnO-based devices printed on paper, paving the way to low-cost and sophisticated paper-based sensors.

The present contribution evaluates the methods of degradation and stabilization of alum-containing paper with a focus on the alkaline environment achieved by deacidification procedures. In terms of reviewed subjects, the contribution focuses on alum-rosin sized paper, which is still used as a carrier of knowledge and information; however, it also mentions cellulose itself and other brands of paper. The contribution summarizes the results on the homogeneity of the distribution of alum and rosin in the paper mass and on the paper surface. It provides the knowledge gained in the field of alkaline hydrolysis and oxidation with special regard to transition metal species. It shows the values of alkaline reserves achieved in the main mass-deacidification processes. On the basis of the acquired knowledge, the contribution emphasizes the procedures of paper stabilization. Criteria of “increased mechanical permanence and lifetime prolongation” adopted to evaluate and compare the efficacy of individual mass-deacidification processes were applied and corresponding data are introduced. The contribution also draws attention to the existence of open issues in the area of paper degradation and stabilization.

Flying insect detection, identification, and counting are the key components of agricultural pest management. Insect identification is also one of the most challenging tasks in agricultural image processing. With the aid of machine vision and machine learning, traditional (manual) identification and counting can be automated. To achieve this goal, a particular data acquisition device and an accurate insect recognition algorithm (model) is necessary. In this work, we propose a new embedded system-based insect trap with an OpenMV Cam H7 microcontroller board, which can be used anywhere in the field without any restrictions (AC power supply, WIFI coverage, human interaction, etc.). In addition, we also propose a deep learning-based insect-counting method where we offer solutions for problems such as the “lack of data” and “false insect detection”. By means of the proposed trap and insect-counting method, spraying (pest swarming) could then be accurately scheduled.

Each year the pulp and paper industries generate enormous amounts of effluent treatment sludge. The sludge is made up of various fractions including primary, secondary, deinked, fiber rejects sludge, etc. The goal of this study was to evaluate the fuel properties of the hydrochars produced from various types of paper mill sludges (PMS) at 180 °C, 220 °C, and 260 °C. The hydrochars, as well as the raw feedstocks, were characterized by means of ultimate analysis, proximate analysis, moisture, ash, lignin, sugar, and higher heating value (HHVdaf) measurements. Finally, combustion indices of selected hydrochars were evaluated and compared with bituminous coal. The results showed that HHVdaf of hydrochar produced at 260 °C varied between 11.4 MJ/kg and 31.5 MJ/kg depending on the feedstock. This implies that the fuel application of hydrochar produced from PMS depends on the quality of feedstocks rather than the hydrothermal carbonization (HTC) temperature. The combustion indices also showed that when hydrochars are co-combusted with coal, they have similar combustion indices to that of coal alone. However, based on the energy and ash contents in the produced hydrochars, Primary and Secondary Sludge (PPS2) could be a viable option for co-combustion with coal in an existing coal-fired power plant.

Due to the health and environment impacts of fossil fuels utilization, biofuels have been investigated as a potential alternative renewable source of energy. Bioethanol is currently the most produced biofuel, mainly of first generation, resulting in food-fuel competition. Second generation bioethanol is produced from lignocellulosic biomass, but a costly and difficult pretreatment is required. The pulp and paper industry has the biggest income of biomass for non-food-chain production, and, simultaneously generates a high amount of residues. According to the circular economy model, these residues, rich in monosaccharides, or even in polysaccharides besides lignin, can be utilized as a proper feedstock for second generation bioethanol production. Biorefineries can be integrated in the existing pulp and paper industrial plants by exploiting the high level of technology and also the infrastructures and logistics that are required to fractionate and handle woody biomass. This would contribute to the diversification of products and the increase of profitability of pulp and paper industry with additional environmental benefits. This work reviews the literature supporting the feasibility of producing ethanol from Kraft pulp, spent sulfite liquor, and pulp and paper sludge, presenting and discussing the practical attempt of biorefineries implementation in pulp and paper mills for bioethanol production.

A flexible pressure sensor with a rudimentary, ultra-low cost, and solvent-free fabrication process is presented in this paper. The sensor has a graphite-on-paper stacked paper structure, which deforms and restores its shape when pressure is applied and released, showing an exceptionally fast response and relaxation time of &asymp, 0.4 ms with a sensitivity of &minus, 5%/Pa. Repeatability of the sensor over 1000 cycles indicates an excellent long-term stability. The sensor demonstrated fast and reliable human touch interface, and successfully integrated into a robot gripper to detect grasping forces, showing high promise for use in robotics, human interface, and touch devices.

Paper mill sludge (PMS) solids are predominantly comprised of cellulosic fibers and fillers rejected during the pulping or paper making process. Most sludges are dewatered and discharged into landfills or land spread at a cost to the mill; creating large economic and environmental burdens. This lignocellulosic residual stream can be used as a source of sugars for microbial fermentation to renewable chemicals. The aim of this study was to determine the possibility of converting mill sludge to sugars and then fermentation to either isoprene or ethanol. Chemical analysis indicated that the cellulosic fiber composition between 28 to 68% and hemicellulose content ranged from 8.4 to 10.7%. Calcium carbonate concentration in the sludge ranged from 0.4 to 34%. Sludge samples were enzyme hydrolyzed to convert cellulose fibers to glucose, percent conversion ranged from 10.5 to 98%. Calcium carbonate present with the sludge resulted in low hydrolysis rates; washing of sludge with hydrochloric acid to neutralize the calcium carbonate, increased hydrolysis rates by 50 to 88%. The production of isoprene “very low” (190 to 470 nmol) because the isoprene yields were little. Using an industrial yeast strain for fermentation of the sludge sugars obtained from all sludge samples, the maximum conversion efficiency was achieved with productivity ranging from 0.18 to 1.64 g L−1 h−1. Our data demonstrates that PMS can be converted into sugars that can be fermented to renewable chemicals for industry.

This work describes the use of a paper substrate for electro-optical detection of toxic hydrogen sulfide (H2S) gas. For electrical detection, a chemiresistive type of gas sensor was developed. Ultrathin gold film electrodes (UTGFE) were produced by physical vapor deposition of gold on nanostructured latex-coated paper substrate. The gas-sensing film was deposited on the electrodes by inkjet printing. The sensing films were characterized by atomic force microscopy, X-ray photoelectron spectroscopy and conductometry. The sensing films showed more than seven orders of magnitude change in resistance when exposed to as low as 1 part per million (ppm) H2S gas at room temperature. Besides resistive response, the change in color of the sensing films was studied on a paper substrate, both as a function of print density of the sensing material and H2S concentration. For quantification of the analyte the red, green and blue color deconvolution was performed on the pictures of the paper strip indicator using an open source software. A clear response was obtained from the blue channel. The inexpensive disposable color strips produced on the paper substrate can be used for qualitative and quantitative detection (as low as 1.5 ppm) of H2S gas. Electro-Optical Gas Sensor Consisting of Nanostructured Paper Coating and an Ultrathin Sensing Element

Food safety and access to systematic approaches for ensuring detection of food hazards is an important issue in most developing countries. With the arrival of paper-based analytical devices (&micro, PADs) as a promising, rapid, easy-to-use, and low-cost analytical tool, we demonstrated a simple microfluidic-based titration study for the analysis of packaged fruit juices. Similar, to the titration experiments using traditional glassware in chemistry laboratories, in this study the titration experiments were developed using paper microfluidics for the analysis of several analytes such as pH, vitamin C, sugars, and preservatives present in the packaged fruit juices. The allergen found commonly in dairy based mixtures and the non-pathogenic biochemical component responsible for food spoilage in cider based fruit juices were also determined. The results obtained using paper microfluidics were compared with those obtained using a conventional spectrophotometric technique. Finally, a paper microfluidics based multiplexed sensor was developed for the analysis of common nutritional ingredients, an allergen, and a non-pathogenic byproduct present in packaged fruit juices on a single platform. Overall, the results presented in this study reveal that the proposed paper microfluidic assisted colorimetric multiplexed sensor offers a quick and reliable tool for on-spot routine analysis for food safety applications.

Tetracycline is widely used as medicine for disease treatments and additives in animal feeding. Unfortunately, the abuse of tetracycline inevitably causes tetracycline residue in animal-origin foods. Though classical methods can detect tetracycline in high sensitivity and precision, they often rely on huge and expensive setups as well as complicated and time-consuming operations, limiting their applications in rapid and on-site detection. Here, we propose a handheld inkjet printing paper chip based smart tetracycline detector: tetracycline can be determined by inkjet printing prepared paper chip based enzyme-linked immunosorbent assay (ELISA) with the advantages of high sensitivity, excellent specificity and low cost, moreover, a smartphone based paper chip reader and application is designed for automatically determining tetracycline with simple operations, high precision and fast speed. The smart tetracycline detector with a compact size of 154 mm × 80 mm × 50 mm and self-supplied internal power can reach a rather low detection limit of ~0.05 ng/mL, as proved by practical measurements. It is believed the proposed handheld inkjet printing paper chip based smart tetracycline detector is a potential tool in antibiotic sensing for routine uses at home and on-site detection in the field.

The Ceramics journal has reached its first milestone with the publication of the 100th paper since its creation in 2018 [...]

In the last 20 years, with the liberalization of the economy, and the trend of industrial globalization, people have gradually paid more attention to environmental protection. With the tremendous advances in information technology, enterprises facing such a severe impact on the business operations, business administrative models must be innovative and adaptable in order to survive and flourish. The paper industry is not only a highly polluting industry, but in the case of long-term overcapacity, the price of paper products is often suppressed, which lowers profitability. The purpose of this study, which is based on the production data of a paper company, is to pose a mathematical programming decision model which integrates green manufacturing technologies, activity-based costing (ABC), and the theory of constraint (TOC), this model should assist in preparing the best production plans, and achieve the optimal profitable product mix. In addition, this study also proposes that the most popular related technologies developed by Industry 4.0 be applied to production control in recent years in order to enhance production efficiency and quality. The findings of this study should contribute to the improvement of the competitiveness of the paper industry, and provide insights into the value of an integrated mathematical programming model applied for product-mix decision. At the same time, we have also applied the related technologies developed by Industry 4.0 to machine maintenance and quality control in manufacturing workshops. With its tremendous benefits, we can actively arouse the industry&rsquo, s understanding of, and attention to, Industry 4.0, thereby increasing the interest in industrial 4.0-related technology investments.

Global energy consumption is increasing every year, and, despite their many negative impacts, fossil fuels are a major source of energy, but their reserves are gradually depleting. One of the promising but underutilized resources is plant biomass (phytomass). The main problem of plant biomass combustion is the low melting temperature of ash, but there are also problems with corrosion of heat exchangers and clogging of heat-exchanging surfaces. This work is concerned with the production of straw pellets in order to increase the melting temperature of ash by adding an additive. The paper sludge contains substances that can increase the melting point of ash and was therefore added to the pellet samples. This additive was mixed with straw in ratios from 90:10, 80:20 and 70:30 (straw/paper sludge). The use of paper sludge showed positive effects on increasing the melting temperature of the ash samples. The deformation temperature of the ash has already risen from 1020 to 1260 &deg, C after the addition of 10% sludge, which is comparable to wood pellets.

Untethered small-scale soft robots have been widely researched because they can be employed to perform wireless procedures via natural orifices in the human body, or other minimally invasive operations. Nevertheless, achieving untethered robotic motion remains challenging owing to the lack of an effective wireless actuation mechanism. To overcome this limitation, we propose a magnetically actuated walking soft robot based on paper and a chained magnetic-microparticle-embedded polymer actuator. The magnetic polymer actuator was prepared by combining Fe3O4 magnetic particles (MPs, diameter of ~50 nm) and silicon that are affected by a magnetic field, thereafter, the magnetic properties were quantified to achieve proper force and optimized according to the mass ratio, viscosity, and rotational speed of a spin coater. The fabricated polymer was utilized as a soft robot actuator that can be controlled using an external magnetic field, and paper was employed to construct the robot body with legs to achieve walking motion. To confirm the feasibility of the designed robot, the operating capability of the robot was analyzed through finite element simulation, and a walking experiment was conducted using electromagnetic actuation. The soft robot could be moved by varying the magnetic flux density and on&ndash, off state, and it demonstrated a maximum moving speed of 0.77 mm/s. Further studies on the proposed soft walking robot may advance the development of small-scale robots with diagnostic and therapeutic functionalities for application in biomedical fields.

The newly developed research area of inkjet-printed radio frequency (RF) electronics on cellulose-based and synthetic paper substrates is introduced in this paper. This review paper presents the electrical properties of the paper substrates, the printed silver nanoparticle-based thin films, the dielectric layers, and the catalyst-based metallization process. Numerous inkjet-printed microwave passive/ative systems on paper, such as a printed radio frequency identification (RFID) tag, an RFID-enabled sensor utilizing carbon nanotubes (CNTs), a substrate-integrated waveguide (SIW), fully printed vias, an autonomous solar-powered beacon oscillator (active antenna), and artificial magnetic conductors (AMC), are discussed. The reported technology could potentially act as the foundation for true “green” low-cost scalable wireless topologies for autonomous Internet-of-Things (IoT), bio-monitoring, and “smart skin” applications.

Microfluidic paper-based analytical devices (microPADs) have emerged as a promising platform for point-of-care diagnostic devices. While the inherent wicking properties of microPADs allow for fluid flow without supporting equipment, this also presents a major challenge in achieving robust fluid control, which becomes especially important when performing complex multi-step assays. Herein, we describe an ideal method of fluid control mediated by wax-printed fluidic time delays. This method relies on a simple fabrication technique, does not utilize chemicals/reagents that could affect downstream assays, is readily scalable, and has a wide temporal range of tunable fluid control. The delays are wax printed on both the top and bottom of pre-fabricated microPAD channels, without subsequent heating, to create hemi-/fully-enclosed channels. With these wax printed delays, we were able to tune the time it took aqueous solutions to wick across a 25 mm-long channel between 3.6 min and 13.4 min. We then employed these fluid delays in the sequential delivery of four dyes to a test zone. Additionally, we demonstrated the automation of two simple enzymatic assays with this fluid control modality. This method of fluid control may allow future researchers to automate more complex assays, thereby further advancing microPADs toward real-world applications.

In the context of global climate change, energy conservation and greenhouse effect gases (GHG) reduction are major challenges to mankind. The forestry-pulp and paper industry is a typical high energy consumption and high emission industry. We conducted in-depth research on the energy flows and carbon footprint of the forestry-pulp paper industry. The results show that: (1) The main sources of energy supply include external fossil fuel coal and internal biomass fuel black liquor, which supply 30,057,300 GJ and 14,854,000 GJ respectively, in addition, the energy produced by diesel in material transportation reaches 11,624,256 GJ. (2) The main energy consumption processes include auxiliary engineering projects, material transportation, papermaking, alkali recovery, pulping and other production workshops. The percentages of energy consumption account for 26%, 18%, 15%, 10% and 6%, respectively. (3) The main sources of carbon include coal and forest biomass, reaching 770,000 tons and 1.39 million tons, respectively. (4) Carbon emissions mainly occur in fuel combustion in combined heating and power (CHP) and diesel combustion in material transportation, reaching 6.78 million tons and 790,000 tons of carbon, respectively. (5) Based on steam and electricity consumption, the indirect carbon emissions of various thermal and electric energy production units were calculated, and the key energy consumption process units and hotspot carbon flow paths were further found. This research established a theoretical and methodological basis for energy conservation and emission reduction.

Today, there are many recent developments that focus on improving the electric vehicles and their components, particularly regarding advances in batteries, energy management systems, autonomous features and charging infrastructure. This plays an important role in developing next electric vehicle generations, and encourages more efficient and sustainable eco-system. This paper not only provides insights in the latest knowledge and developments of electric vehicles (EVs), but also the new promising and novel EV technologies based on scientific facts and figures—which could be from a technological point of view feasible by 2030. In this paper, potential design and modelling tools, such as digital twin with connected Internet-of-Things (IoT), are addressed. Furthermore, the potential technological challenges and research gaps in all EV aspects from hard-core battery material sciences, power electronics and powertrain engineering up to environmental assessments and market considerations are addressed. The paper is based on the knowledge of the 140+ FTE counting multidisciplinary research centre MOBI-VUB, that has a 40-year track record in the field of electric vehicles and e-mobility.

Although recycling is considered the core of a circular economy for returning materials to the supply chain, its procedures are poorly understood. Waste recycling is considered a big source of energy saving and a promoter of CO2 recovery. Besides that, it generates jobs and changes markets worldwide. The Brasilian National Policy on Solid Waste (PNRS) recognizes Waste Pickers as the major social agent in the recycling process responsible for putting Brasil among the ten largest paper-recycling countries in the world. This paper presents an analysis of Brasilian recycling chains of paper and plastics and the main challenges for expanding recycling from Municipal solid waste. The research data were obtained from primary and secondary source related to the recycling supply chain of paper and of the following plastics—High Density Polyethylene (HDPE),Low Density Polyethylene (LDPE), Polypropylene(PP), Polyethylene Terephthalate(PET) and Polystyrene(PS). Enterprises of various sizes, including informal ones and WPs associations/cooperatives, were visited, in the five Brasilian geographic regions, during the years of 2013 and 2014. A nomenclature was defined for the various enterprises that operate in the Brasilian recycling chain. Each node of the plastic and paper recycling chain was described. The main bottleneck observed in these chains is the lack of continuous programs of selective collection with an emphasis on environmental education processes in the 5570 Brasilian municipalities. Several possibilities not only to promote waste recycling but also to increase the productivity of the sorting process are discussed.

In this perspective article, some of the latest paper and fiber-based bio-analytical platforms are summarized, along with their fabrication strategies, the processing behind the product development, and the embedded systems in which paper or fiber materials were integrated. The article also reviews bio-recognition applications of paper/fiber-based devices, the detected analytes of interest, applied detection techniques, the related evaluation parameters, the type and duration of the assays, as well as the advantages and disadvantages of each technique. Moreover, some of the existing challenges of utilizing paper and/or fiber materials are discussed. These include control over the physical characteristics (porosity, permeability, wettability) and the chemical properties (surface functionality) of paper/fiber materials are discussed. Other aspects of the review focus on shelf life, the multi-functionality of the platforms, readout strategies, and other challenges that have to be addressed in order to obtain reliable detection outcomes. Keywords: paper-based bio-analytical devices; shelf life; equipment-free bio-recognition; flow rate; readout strategies; multi-functional platforms

Applied Sciences has achieved a major milestone this year: it is the 10th anniversary of the journal [...]

Rapid assessment of burn depth is important for burn wound management. Superficial partial-thickness burn (SPTB) wounds heal without scars, but deep partial-thickness burn (DPTB) wounds require a longer healing time and have a higher risk of scar formation. We previously found that DPTB blister fluid displayed a higher angiogenin level than SPTB blister fluid by conventional ELISA. In this study, we developed a paper-based ELISA (P-ELISA) technique for rapid assessment of angiogenin concentration in burn blister fluid. We collected six samples of SPTB blister fluid, six samples of DPTB blister fluid, and seven normal healthy serum samples for analysis. We again chose ELISA to measure and compare angiogenin levels across all of our samples, but we developed a P-ELISA tool and compared sample results from that tool to the results from conventional ELISA. As with conventional ELISA, DPTB blister fluid displayed higher angiogenin levels than SPTB in P-ELISA. Furthermore, our P-ELISA results showed a moderate correlation with conventional ELISA results. This new diagnostic technique facilitates rapid and convenient assessment of burn depth by evaluating a key molecule in burn blister fluid. It presents a novel and easy-to-learn approach that may be suitable for clinically determining burn depth with diagnostic precision.

This paper reflects the technology-induced novelty of translation, which is perceived as a bridge between languages and cultures. We debate the extent to which the translation process maintains its specificity in the light of the new technology-enhanced working methods ensured by a large variety of Computer-Assisted Translation (CAT) and Machine Translation (MT) tools that aim to enhance the process, which includes the translation itself, the translator, the translation project manager, the linguist, the terminologist, the reviewer, and the client. This paper also hints at the topic from the perspective of the translation teacher, who needs to provide students with transversal competencies that are suitable for the digital area, supported by the ability to tackle Cloud-based translation tools, in view of Industry 4.0 requirements.

Industrial archived process data represent a convenient source of information for data-driven models, such as artificial neural network (ANN), that can be used for safety and efficiency improvement like early or even predictive fault detection and diagnosis (FDD). Nonetheless, most of the data used for model generation are representative of the process nominal states and therefore are not enough for classification problems intended to determine abnormal process conditions. This work proposes the use of techniques to augment the original real data standards, dismissing the need for experiments that could jeopardize process safety. It uses the Monte Carlo technique to artificially increase the number of model inputs coupled to the nearest neighbor search (NNS) by geometric distances to consistently classify the generated patterns in normal or faulty statuses. Finally, a radial basis function neural network is trained with the augmented data. The methodology was validated by a study case in which 3381 pulp and paper industrial data points were expanded to monitor the formation of particles in a recovery boiler. Only 5.8% of the original process data were examples of faulty conditions, but the new expanded and balanced data collection leveraged the classification performance of the neural network, allowing its future use for monitoring purpose.

This manuscript presents a comprehensive literature review with the aim to provide readers a reference document with up-to-date information on the field of methanol use as a chemical marker. It has been a little more than a decade since methanol was first introduced as a marker for assessing solid insulation condition in power transformers. It all started when methanol was identified in the laboratory during thermal ageing tests carried out with oil-immersed insulating papers and was subsequently also identified in transformer field samples. The first publication on the subject was released in 2007 by our research group. This review covers the methanol fundamentals such as the analytical methods for its determination in transformer oil, which is generally performed by headspace gas chromatography with mass spectrometry or flame ionization as a detector. Current standardization efforts for its determination include ASTM working group 30948 and IEC TC10. Kinetic studies have confirmed the relationship between methanol generation, the number of broken 1,4-β-glycosidic bonds of cellulose and changes in mechanical properties. Laboratory tests have confirmed its stability at different accelerated ageing temperatures. Several utilities have identified methanol during field measurements, case studies on power and some distribution transformers are presented, as well as transformer postmortem investigations. These field-testing results demonstrate its utility in monitoring cellulosic insulation degradation. Recently, a model of methanol interpretation has become available that allows for evaluation of the average degree of polymerization of core type transformer cellulose winding. Methanol has a role as an indicator of cellulosic solid insulation ageing in transformer mineral oil, and it is expected that in the future it will be in routine use by utilities.

Paper-based analytical devices are an emerging class of lightweight and simple-to-use analytical platform. However, challenges such as instrumental requirements and chemical reagents durability, represent a barrier for less-developed countries and markets. Herein, we report an advanced laminated device using red emitting copper nanocluster and RGB digital analysis for signal improvement. Upon RGB system assistance, the device signal-to-background ratio and the calibration sensitivity are highly enhanced under a filter-free setup. In addition, the calibration sensitivity, limit of detection, and coefficient of determination are on par with those determined by instrumental fluorescence analysis. Moreover, the limitation of using oxidation-susceptible fluorescent nanomaterials is overcome by the introduction of protecting tape barriers, antioxidative sheets, and lamination enclosing. The robustness of device is highly advanced, and the durability is prolonged to more than tenfold.

The electrophoresis of ampholytes such as amino acids on a paper device is difficult because of the variation of pH distribution in time. On the basis of this observation, we propose a paper-based analytical device (PAD) with origami structure. By folding a filter paper, a low operation voltage of 5 V was achieved, where the power was supplied by a 5 V 1.5 A portable power bank through the USB type A receptacle. As a demonstration, we carried out the electrophoretic separation of pI markers (pI 5.5 and 8.7). The separation was achieved within 4 min before the pH distribution on the paper varied. Though the separation distance was small, it could be increased by expanding the origami structure. This result indicates that our proposed PAD is useful for electrophoretic separation on a paper device.

Fully printed and flexible inorganic electrolyte gated transistors (EGTs) on paper with a channel layer based on an interconnected zinc oxide (ZnO) nanoparticle matrix are reported in this work. The required rheological properties and good layer formation after printing are obtained using an eco-friendly binder such as ethyl cellulose (EC) to disperse the ZnO nanoparticles. Fully printed devices on glass substrates using a composite solid polymer electrolyte as gate dielectric exhibit saturation mobility above 5 cm2 V&minus, 1 s&minus, 1 after annealing at 350 &deg, C. Proper optimization of the nanoparticle content in the ink allows for the formation of a ZnO channel layer at a maximum annealing temperature of 150 &deg, C, compatible with paper substrates. These devices show low operation voltages, with a subthreshold slope of 0.21 V dec&minus, 1, a turn on voltage of 1.90 V, a saturation mobility of 0.07 cm2 V&minus, 1 and an Ion/Ioff ratio of more than three orders of magnitude.

This paper demonstrates the performance of a potential design of a paper substrate-based flexible antenna for intrabody telemedicine systems in the 2.4 GHz industrial, scientific, and medical radio (ISM) bands. The antenna was fabricated using 0.54 mm thick flexible photo paper and 0.03 mm copper strips as radiating elements. Design and performance analyses of the antenna were performed using Computer Simulation Technology (CST) Microwave Studio software. The antenna performances were investigated based on the reflection coefficient in normal and bent conditions. The total dimensions of the proposed antenna are 40 &times, 35 &times, 0.6 mm3. The antenna operates at 2.33&ndash, 2.53 GHz in the normal condition. More than an 8% fractional bandwidth is expressed by the antenna. Computational analysis was performed at different flexible curvatures by bending the antenna. The minimum fractional bandwidth deviation is 5.04% and the maximum is 24.97%. Moreover, it was mounted on a homogeneous phantom muscle and a four-layer human tissue phantom. Up to a 70% radiation efficiency with a 2 dB gain was achieved by the antenna. Finally, the performance of the antenna with a homogeneous phantom muscle was measured and found reliable for wearable telemedicine applications.

The work presented details the manufacturing of a low-cost hybrid inkjet-printed paper-based potentiostat, with the aim of creating a low-cost sensing system for rapid water quality monitoring. Potentiostats exhibit high sensitivities and can be used for a variety of applications. The results highlight the functionality of a paper-based potentiostat compared to a potentiostat manufactured on a printed circuit board (PCB), an LMP91000EVM development board and a laboratory-based Metrohm Autolab potentiostat. Cyclic voltammetry was performed using an 80 &micro, L sample of 5 mM ferri-ferrocyanide dropped onto a commercial screen-printed electrode from DropSens. The miniaturized paper-based potentiostat is small enough to be stored in a wallet and therefore easy to transport. Furthermore, a cost analysis shows that the potentiostat is 10 times lower in cost than the commercially available handheld potentiostat, taking the costs of man hours into account. This technology enables electrochemistry experiments to be performed on-site using the portable, disposable and low-cost solution and can be applied to a variety of fields including healthcare, wearables and environmental monitoring.

Timely evaluation and reperfusion have improved the myocardial salvage and the subsequent recovery rate of the patients hospitalized with acute myocardial infarction (MI). Long waiting time and time-consuming procedures of in-hospital diagnostic testing severely affect the timeliness. We present a Poincare pattern ensemble-based method with the consideration of multi-correlated non-stationary stochastic system dynamics to localize the infarct-related artery (IRA) in acute MI by fully harnessing information from paper-based Electrocardiogram (ECG). The vectorcardiogram (VCG) diagnostic features extracted from only 2.5-s long paper ECG recordings were used to hierarchically localize the IRA&mdash, not mere localization of the infarcted cardiac tissues&mdash, in acute MI. Paper ECG records and angiograms of 106 acute MI patients collected at the Heart Artery and Vein Center at Fresno California and the 12-lead ECG signals from the Physionet PTB online database were employed to validate the proposed approach. We reported the overall accuracies of 97.41% for healthy control (HC) vs. MI, 89.41 &plusmn, 9.89 for left and right culprit arteries vs. others, 88.2 &plusmn, 11.6 for left main arteries vs. right-coronary-ascending (RCA) and 93.67 &plusmn, 4.89 for left-anterior-descending (LAD) vs. left-circumflex (LCX). The IRA localization from paper ECG can be used to timely triage the patients with acute coronary syndromes to the percutaneous coronary intervention facilities.

The rapid development of information and communication technology provides an opportunity for scientists to develop a quantitative analytical method that is built on a mobile gadget as a detector. In this paper, we report a low-cost, simple and portable analytical method for mercury ion quantification based on digital image colorimetry coupled with a smartphone application. A small amount of silver nanoparticles (AgNPs) was used as a colorimetric agent that is selective only to mercury ions. The yellowish brown color of AgNPs instantly changed to colorless after the addition of mercury ions due to a redox reaction. To increase the portability, we attached the AgNPs onto a medium to create a paper-based analytical device. The final data processing of the colorimetric analysis was conducted using an android application available on the Google Play Store, called &ldquo, Mercury Detector&rdquo, The proposed method has good sensitivity, with a detection limit of 0.86 ppb, which is comparable to those of bulk and more expensive instruments. This allows for the detection of mercury ions as low as 2 ppb (10 nM), which is also the maximum contaminant level permitted in drinking water by the US Environmental Protection Agency. The proposed method was applied to real samples that provide satisfactory results on accuracy (2.4%) and precision (2.5%).

The number of elderly people as a proportion of the world’s population is growing significantly. Special attention to the accessibility and mobility requirements of this group is needed. The contribution of this paper is a review of travel patterns, mode preferences, infrastructure solutions, accessibility indices, mode choice models and datasets as they relate to elderly mobility. Key findings highlight the role of residential location characteristics in shaping elderly travel patterns, helping to explain why research on elderly travel has largely relied on case studies to date. The review also summarizes a range of indices that have been developed to measure public transport and walking accessibility among the elderly, including distance and time-based methods. Future research should consider the dominance of private transport in facilitating elderly mobility and its implications for cities experiencing an aging population.

Most power transformers operating in a power system possess oil-paper insulation. A serious defect of this type of insulation, which is associated with long operation time, is an increase in the moisture content. Moisture introduces a number of threats to proper operation of the transformer, e.g., ignition of partial discharges (PDs). Due to the varying temperature of the insulation system during the unit’s normal operation, a dynamic change (migration of water) takes place, precipitating the oil-paper system from a state of hydrodynamic equilibrium. This causes the PDs to be variable in time, and they may intensify or extinguish. Studies on model objects have been conducted to determine the conditions (temperature, humidity, time) that will have an impact on the ignition and intensity of the observed phenomenon of PDs. The conclusions of this study will have a practical application in the evaluation of measurements conducted in the field, especially in relation to the registration of an online PD monitoring system.

A simple method for microfluidic paper-based sample concentration using ion concentration polarization (ICP) with smartphone detection is developed. The concise and low-cost microfluidic paper-based ICP analytical device, which consists of a black backing layer, a nitrocellulose membrane, and two absorbent pads, is fabricated with the simple lamination method which is widely used for lateral flow strips. Sample concentration on the nitrocellulose membrane is monitored in real time by a smartphone whose camera is used to collect the fluorescence images from the ICP device. A custom image processing algorithm running on the smartphone is used to track the concentrated sample and obtain its fluorescence signal intensity for quantitative analysis. Two different methods for Nafion coating are evaluated and their performances are compared. The characteristics of the ICP analytical device especially with intentionally adjusted physical properties are fully evaluated to optimize its performance as well as to extend its potential applications. Experimental results show that significant concentration enhancement with fluorescence dye sample is obtained with the developed ICP device when a fast depletion of fluorescent dye is observed. The platform based on the simply laminated ICP device with smartphone detection is desired for point-of-care testing in settings with poor resources.

Porous microstructure pressure sensors that are highly sensitive, reliable, low-cost, and environment-friendly have aroused wide attention in intelligent biomedical diagnostics, human&ndash, machine interactions, and soft robots. Here, an all-tissue-based piezoresistive pressure sensor with ultrahigh sensitivity and reliability based on the bottom interdigitated tissue electrode and the top bridge of a microporous tissue/carbon nanotube composite was proposed. Such pressure sensors exhibited ultrahigh sensitivity (&asymp, 1911.4 kPa&minus, 1), fast response time (&lt, 5 ms), low fatigue of over 2000 loading/unloading cycles, and robust environmental degradability. These enabled sensors can not only monitor the critical physiological signals of the human body but also realize electrothermal conversion at a specific voltage, which enhances the possibility of creating wearable thermotherapy electronics for protecting against rheumatoid arthritis and cervical spondylosis. Furthermore, the sensor successfully transmitted wireless signals to smartphones via Bluetooth, indicating its potential as reliable skin-integrated electronics. This work provides a highly feasible strategy for promoting high-performance wearable thermotherapy electronics for the next-generation artificial skin.

As a pump-free and lightweight analytical tool, paper-based microfluidic analytical devices (μPADs) attract more and more interest. If the flow speed of μPAD can be programmed, the analytical sequences could be designed and they will be more popular. This reports presents a novel μPAD, driven by the capillary force of cellulose powder, printed by a desktop three-dimensional (3D) printer, which has some promising features, such as easy fabrication and programmable flow speed. First, a suitable size-scale substrate with open microchannels on its surface is printed. Next, the surface of the substrate is covered with a thin layer of polydimethylsiloxane (PDMS) to seal the micro gap caused by 3D printing. Then, the microchannels are filled with a mixture of cellulose powder and deionized water in an appropriate proportion. After drying in an oven at 60 °C for 30 min, it is ready for use. As the different channel depths can be easily printed, which can be used to achieve the programmable capillary flow speed of cellulose powder in the microchannels. A series of microfluidic analytical experiments, including quantitative analysis of nitrite ion and fabrication of T-sensor were used to demonstrate its capability. As the desktop 3D printer (D3DP) is very cheap and accessible, this device can be rapidly printed at the test field with a low cost and has a promising potential in the point-of-care (POC) system or as a lightweight platform for analytical chemistry.

As a basic mechanical component, the sealing ring is widely used in industrial, aerospatial, and other fields. In this study, an elastic metal C-shaped sealing ring with a wave structure was taken as an example, and its performance was analyzed theoretically and measured experimentally. First, an experimental study was performed on the C-ring seal. The proposed method for experimental measurement of the contact stress of the C-ring seal involved innovative use of a universal electronic testing machine and pressure sensitive paper, in conjunction with the hue&ndash, saturation&ndash, brightness (HSB) method. Based on the discoloration of the pressure sensitive paper after contact stress, computer software was used for analysis, the discoloration was digitized, and the contact stress was established. Second, a theoretical calculation model of the C-ring seal was established using ANSYS software, and a finite element theoretical calculation of the mechanical properties of the sealing ring was established. Finally, the contact stress results were compared with the model calculation results of the C-ring seal. The error between the two was small (4.8%), which proved the validity of the calculation model and the scientificity of the experimental method.