Search

Frequency Domain Spectroscopy (FDS) is proposed as a suitable diagnostic method in this paper for implementation on energized oil-paper insulation systems. In present FDS tests, the measurement method is only designed for offline applications. To overcome the deficiencies with the offline testing, this work investigates the feasibility of performing FDS measurements on energized transformers with the view to developing an online diagnostic tool using neutral connections as injection and measurement paths. In the proposed technique, a low-pass filter system is designed to remove the high frequency noise as well as the power frequency signals present in the measured neutral currents. The technique has been successfully applied in a laboratory environment on transformers with oil-paper insulation systems with different operational ages and is feasible for single-phase as well as 3-phase transformers with the accessible neutral points. Compared with the conventional FDS results, a nonlinear dielectric phenomenon is observed from the energized insulation systems as higher dissipation factor Tanδ values primarily due to the increased losses under power frequency voltage excitation. The degree of the nonlinearity is found to correlate well with the degradation status of insulation systems under test.

Millimeter-wave imaging may be used to assist in\ud the problem of wastepaper recognition during the sorting and\ud recycling process. Currently, there are a variety of techniques,\ud which are used within materials recovery facilities to sort waste\ud paper and card; however, improvements in sorting capability can\ud be realized using a multiple sensors to provide complementary\ud (orthogonal) data. This paper discusses the issues related to\ud the processes, which are currently used for sorting of recycled\ud wastepaper and the phenomenology for millimeter-wave imaging\ud of a wastepaper material. Experimental measurements and\ud images in the millimeter wave band are presented, which support\ud the proposed application.

Superchannel transmission is a candidate to realize Tb/s-class high-speed optical communications. In order to achieve higher spectrum efficiency, the channel spacing shall be as narrow as possible. However, densely allocated channels can cause non-negligible inter-channel interference (ICI) especially when the channel spacing is close to or below the Nyquist bandwidth. In this paper, we consider joint decoding to cancel the ICI in dense superchannel transmission. To further improve the spectrum efficiency, we propose the use of Han–Kobayashi superposition coding. In addition, for the case when neighboring subchannel transmitters can share data, we introduce dirty-paper coding for pre-cancelation of the ICI. We analytically evaluate the potential gains of these methods when ICI is present for sub-Nyquist channel spacing.

This study investigated technologies related to a smart-card display and its wireless charging system, where the wireless receiver in the smart card receives not only the data but also the power required for the display circuitry. The goal of this research was to achieve the required energy transfer during the extremely short reading time when a person swipes his or her smart card. This paper describes the design considerations and the analysis procedures of the transmitter and receiver pair for an electronic paper (E-paper) display. A series of magnetic simulations as well as experimental tests were conducted to investigate the various design factors. The design considerations included the shape and effect of using ferromagnetic cores, the component design for frequency tuning, the geometric arrangements, and the number of turns of the coils. A novel design for power transmission is then proposed using a ferromagnetic core to enhance its energy efficiency. In experiments the transmitter unit prov...

The capacitively-coupled wireless power transmitting system which provides a wide power-supply position was developed to realize a battery-less electronic paper. The high frequency, 13.56 MHz, was employed and the frequency was modulated to keep the resonant conditions. The special electrode configuration and circuit to suppress EMI were revealed.

We present an ultra-high frequency radio frequency identification based wireless communication set-up for paper-based point-of-care diagnostic applications, based on a sensing radio frequency identification chip. Paper provides a low-cost, disposable platform for ease of fluidic handling without bulky instrumentation, and is thus ideally suited for point-ofcare applications; however, result communication – a crucial aspect for healthcare to be implemented effectively – is still lacking. Printing of radio frequency identification antennas and electronic circuitry for sensing on paper are presented, with read out of the results using a radio frequency identification reader illustrated, demonstrating the feasibility of developing integrated, all-printed solutions for point-of-care diagnosis in resource-limited settings.

Paper defects mean that there are some defects in the paper such as hole, emboss, and fold during the paper production, which mainly results from the limitation of technological level. In the past time, artificial visual inspection and off-line checking were often used to detect the paper defects. However, its shortcoming was highlighted along with the improvement of industrial technology level and increasing demand for paper. In order to realize the online detection and markers for paper defects, the project designs the on-line detection system based on line-scan digital camera. Firstly, the principle and detection scheme of the system for the paper defects was presented. Then the overall structure of the system was designed. After that, the hardware circuit of the system was designed using TMS320F2812 as main control chip. It mainly consists of the function of each module and the working process of the system. Finally, the software of the image acquisition system was presented. With the experimental verification, the system has advantages of low cost, high efficiency and strong resistance to interference. The functions and indexes achieved the design requirements.

Recent research activities in the area of low-cost sensing and diagnostics that are realized on cellulosic paper substrate are presented. First a three-dimensional origami paper-based analytical device (omPAD) with multiple electrochemical sensors, an integrated sample reservoir and tight integration with a custom CMOS potentiostat is presented. Second, an optical sensor array with built-in microfluidic channel for sample delivery is presented. The sensors are fabricated using a combination of wax printing and screen-printing using a solution based approach in ambient conditions without the need for expensive fabrication equipment or a cleanroom. Readout is based on using existing consumer grade electronic devices like flatbed scanner (for optical sensor) or custom designed CMOS potentiostat (for electrochemical sensors). Together the 3D paper-based analytical device with integrated sensor, microfluidics and portable readout instrumentation demonstrates a low-cost, self-contained system suitable for sensing and point-of-care diagnostics.

Airbus Defence and Space Electronics have developed in last recent years a modular and scalable concept for Instrument Control Units (ICU) which has been used with high success in several missions as EUCLID and MetOp-SG. SpaceWire communication is a key element with this concept. This paper presents the Generic ICU architecture and its application in the MetOp-SG instruments.

A handheld wireless optical reader for the detection of infectious diseases at the point of care is presented. The device is battery powered and interfaces with paper-based biosensors for the quantification of concentration in biological fluids using colorimetric analysis. The results are wirelessly transmitted to a smartphone. The device has been successfully tested with various concentrations of Influenza A nucleoprotein.

In paper microfluidics, the development of smart and versatile switches is critical for the regulation of fluid flow across multiple channels. Past approaches in creating switches are limited by long response times, large actuation fluid volumes, and use of external control circuitry. We seek to mitigate these difficulties through the development of a unique actuator device made entirely out of chromatography paper and incorporated with folds. Selective wetting of the fold with an actuation fluid, either at the crest or trough, serves to raise or lower the actuator's tip and thus engage or break the fluidic contact between channels. Here the actuator's response time is dramatically reduced (within two seconds from wetting) and a very small volume of actuation fluid is consumed (four microliters). Using this actuation principle, we implement six switch configurations which can be grouped as single-pole single-throw (normally OFF and normally ON) and single-pole double-throw (with single and double break). By employing six actuators in parallel, an autonomous colorimetric assay is built to detect the presence of three analytes - glucose, protein, and nitrite - in artificial saliva. Finally, this work brings the concept of origami to paper microfluidics where multiple-fold geometries can be exploited for programmable switching of fluidic connections.

The article presents 12.5 Gbit/s Physical Media Attachment (PMA) units, TX and RX, fabricated in 90 nm bulk CMOS process. The PMA are designed for use in SpaceFibre/GigaSpaceWire (SpaceWire-RUS) systems for the space radars. The units comprise SERDES and clock and data recovery (CDR). Supported set of data rates includes those of 1.25, 2.5, 6.25 and 12.5 Gbit/s, but intermediate rates are also available.

Recently paper-based microfluidic chips have been proposed to achieve microfluidic analysis for many applications. Such chips achieve "lab-on-paper" instead of traditional "lab-on-chips". The paper substrate is attractive because it is cost-effective, easy to use and disposable, fully compatible with most medical/biochemical applications, and offering liquid flow by capillary without being relied on external forces and equipment. Test methods for digital microfluidic (DMF) biochips have been studied for years; however, they are developed for traditional DMF chips and thus are not directly applicable to paper-based DMF (PB-DMF) chips. In PB-DMF chips, electrodes are control wires are printed on the same paper surface, while electrodes can be placed with custom structure. In this paper, we present test and diagnosis methods for faults in PB-DMF. A design-for-diagnosability scheme is proposed, and it is shown that single faults can be located and tolerated by providing alternative paths in PB-DMF chips. The feasibility of the proposed method is validated through experiments.

The thin and flexible LSI driver with a thickness of less than 40μm for passive-matrix driven Quick-Response Liquid Powder Display (QR-LPD™) was successfully mounted onto the flexible printed circuit (FPC). The mounted LSI on the plastic substrate shows no significant degradation in the driving performances and keeps physical flexibility without any failures of connection. This technology can realize the fully flexible electronic paper in combination with a plastic substrate QR-LPD™ fabricated by roll-to-roll process.

This paper presents our initial efforts towards the development of screen printed sensors on folded paper substrates for multi-modal sensing of biopotentials, wetness, and pressure. These sensors contain three layers of sensing stripes forming a 16-pixel array where various layers are utilized for different sensing modalities. The performance of the paper-based sensors was assessed. The sensors were shown to exhibit a linear capacitive response to changes in force, as well as a decrease in impedance in the presence of wetness. We discuss the integration of these low-cost and partially disposable paper-based sensors into a wearable diaper system for Bluetooth-based wireless heart rate monitoring, respiratory rate tracking and urination frequency and amount detection.

This paper studied some kinds of realization modes of speed chain compute, load distribution and operation aimed at the realization of paper machine driving system. The frequency conversion control system based on PLC cooperating with digital manipulator was brought forward. It was mainly made up of three parts: PLC, frequency converter and digital manipulator. It used PLC to realize digital speed chain and load distribution. And it exchanged data and parameters by communication through field bus network. The results indicate that the problems of speed chain compute, load distribution and operation were solved effectively by data gathering and computing with PLC, so it is a driving system of high performance.

This paper presents the design and implementation in paper substrate of a harmonic RFID chipless sensing tag. The proposed sensor is based on a Wheatstone bridge, where two of the four impedances change dynamically according to a physical parameter that has to be monitored. The passive tag is interrogated by a signal at f 0 = 1.04 GHz and the signal transmitted back to the reader at 2f 0 = 2.08 GHz is proportional to the magnitude of the parameter variation. A harmonic RFID experiment proves that this kind of architecture is capable of providing a dynamic range of more than 40 dB.

This paper investigates an optimization of the conventional relay selection for multirelay environments. In contrast with previously reported selection schemes, where a selected relay accesses the channel in a dedicated cooperative slot, the proposed scheme recovers the bandwidth loss of the half-duplex constraint by allowing two relays to simultaneously access the channels. Based on an appropriate dirty-paper coding (DPC) technique among relays, the proposed scheme enables a relay to establish communication with the destination at the same time that another relay forwards the data from the source. It is proven that the interplay between relay selection and the superposition DPC weight factor provides a tradeoff between relaying and new data performance. Hence, an appropriate codesign of the superposition DPC parameter and opportunistic relay selection can achieve efficient communication for the new data without affecting the relaying performance. The proposed scheme is compared with conventional relaying approaches, and its enhancements are provided through theoretical studies and numerical results.

This paper collates design concepts of low-power gate driver circuits, and our related work is reviewed. Many approaches to power consumption amelioration have been developed and focus on different parts of circuit structures. Recently, low-frequency clock signals are adopted to further reduce both power consumption and thin-film transistor (TFT) threshold voltage shifts (ΔVTH).

AMOLED displays are still facing the two major challenges after one decade of intensive researches. They are low yield particularly for large panels and modest lifetime due to image sticking. The low yield issue is caused by the analog driving scheme and the image sticking issue is due to the active emitting nature of OLED. With digital driving scheme, the yield of AMOLEDs can be lifted to the level of LCDs. On the other hand, the image sticking issue is getting even severer. It is caused by both, OLED I–V drift and its efficiency loss. In this paper, a method based on aging model is shown which compensates the reduced efficiency of aged OLED pixels. Image sticking artifacts can be deferred and the lifetime of an AMOLED display can significantly be extended. It may ease the penetration of AMOLEDs in TVs and automotive displays performing the high image quality of AMOLEDs with even longer lifetime.

This paper presents the design of a wideband Hilbert fractal antenna for the purpose of detecting and classifying different common partial discharge (PD) types in an oil-paper insulated system. Three common types of PDs are considered for the multi-class classification problem, namely, PD from a sharp point to ground plane, surface discharge, and PD from a void in the insulation. The different PD types showed variation in the detected frequency contents. The collected samples were processed using pattern recognition techniques to identify their corresponding PD types. A recognition rate of 95% was achieved when K-nearest neighbors was used as the classifier.

A dirty-paper channel is considered, where the transmitter knows the interference sequence up to a constant multiplicative factor, known only to the receiver. Lower bounds on the achievable rate of communication are derived by proposing a coding scheme that partially compensates for the imprecise channel knowledge.We focus on a communication scenario where the signal-to-noise ratio is high. Our approach is based on analyzing the performance achievable using lattice-based coding schemes. When the power of the interference is finite, we show that the achievable rate of this lattice-based coding scheme may be improved by a judicious choice of the scaling parameter at the receiver. We further show that the communication rate may be improved, for finite as well as infinite interference power, by allowing randomized scaling at the transmitter.

The rate, quality and economics of printing process are tightly linked to the characteristics of printing technology and materials used. Paper printability is variable property which is according with press conditions and printing characters. A kind of tissue paper used in industrial applications for Puer tea packaging was studied. Tissue paper for Puer tea packaging should have good air permeability because Puer tea needs ferment. Ink receptivity is one of the most important properties of tissue paper in terms of the print quality. The ink receptivity is too strong and ink will not set onto the paper, which make poor color and tone reproduction. Tissue paper was printed with offset fast-drying inks to examine the conditions of tone reproduction, color reproduction and dot gain which determined the printing quality. The immediate objective of this study was to investigate dot gain and tone reproduction of tissue paper.

This paper presents an experimental work investigating the failure data of oil-impregnated paper under pulsating DC voltage. The failure data of the oil-impregnated paper specimens were obtained through constant voltage stress tests; the Weibull distribution was used to estimate the statistical distribution of failure data. The exponential function (EF) and the inverse power function (IPF) were used to modify the Weibull distribution of failure data, so as to obtain two dual-variable Weibull failure distributions (WFDs), which were used to analyze failure data of oil-paper specimens obtained under pulsating DC and individual DC and AC voltages. Their adequacies were evaluated by using failure data obtained through the constant stress tests under various voltages. Both EF-modified and IPF-modified WFDs show more adequacy for failure data of oil-paper insulation under DC and pulsating DC voltages than AC voltages. The EF-modified WFD was more adequate than IPF-modified WFD in estimating the statistical distribution of failure data.

We present an experimental and analytical study of a novel paper-based analytical device (μPAD) for isotachophoretic sample focusing. Guided by a simple heat transfer model, we further developed wax printing fabrication to enable the creation of shallow channels, which are critical in providing sufficient dissipation of Joule heat, and thus enable the use of high electric fields and short analysis time. This results in a device that is self-contained on a simple piece of filter paper and does not require any specialized enclosures or cooling devices to combat evaporation at high temperatures. Furthermore, we provide an analytical model for isotachophoretic sample accumulation in porous media, introduce a simple figure of merit for evaluating and comparing the efficiency of such devices, and present experimental validation in both paper and glass channels. Using this device we demonstrate the processing of 30 μL of sample achieving 1000-fold increase in peak concentration in 6 min. We believe that this method and device can serve as a guide to the design of low-cost, rapid and highly sensitive paper-based diagnostic platforms.

In this paper we study the effect of partial channel state information (CSI) on the performance of dirty paper coding (DPC) schemes. We derive a novel lower bound that shows that the effect of the CSI is upper bounded by the effect of an additive white Gaussian noise with an appropriate variance. The bound is proved using a constructive proof that shows that the predicted rates are achievable using high dimensional lattice modulo precoding schemes. Simulation results demonstrate the usefulness of the bound. The derived bound is useful for the characterization of the interference mitigation performance in partial CSI scenarios such as FDD networks with finite rate feedback, uplink downlink capacity balancing in cooperative cellular networks, etc'.

Currently used methods for estimation of moisture content in paper pulp are restricted to levels of moisture concentration below 90%. Some of the existing methods require less practical double-sided contact measurements. A few other methods make restrictive assumptions, such as the constituents of the pulp that determine its conductance. This paper presents a technique that uses fringing field interdigital sensors to measure moisture concentration in paper pulp at levels as high as 96%. The method proposed in this paper uses single-sided measurements, offers high sensitivity, and does not require special operating conditions. The accuracy of the proposed method is also demonstrated. The repeatability and reproducibility of the sensor measurements are also shown.

Physics based continuous Technology Computer Aided Design (TCAD) models and organic/oxide TFT compact models are key for technology innovation. The encapsulated underlying physics produce predictive models that empower designers to explore all available design space. To achieve this, a number of challenges must be met. These include stable and reproducible fabrication with quantified material parameters. A seamless software flow from TCAD to SPICE opens significant opportunities for future technology designers.

A 3D Stereoscopic Head-Up Display (HUD) using a tunable bandpass filter to perform left and right image spectral separation is presented. Using a single filter reduces the size and the cost of the HUD optical engine, and enables each spectral band to be accurately tuned. Experiments performed on the first prototype demonstrates the ability to continuously tune the bandpass frequency on 30 nm range while keeping a 20 nm bandwidth. Such a system avoids the use of a bulky and costly rotating wheel and enables the use of Holographic Optical Elements known to be wavelength selective.

The flexible AMOLED technology allows us to create new applications because of its unique bendable and foldable properties. With the concept of placing the most fragile layers closed to the neutral plane of the devices, we are able to increase the reliability of flexible displays. Various applications will be introduced including a smart watch with fully circular design, a bendable display with novel interactive interface and a 7.8″ foldable display for phone-tablet 2-in-1 application.

We propose a novel pixel circuit using source-follower structure to be independent of frequency effect of blue-phase liquid crystal displays (BPLCDs). Simulation results indicated that required gray-level-voltages across the BPLC could be achieved accurately when a proper threshold voltage of the driving TFT was chosen. We also successfully fabricated a 12.7-inch prototype BPLCD using the proposed pixel circuit driven with a field-sequential-color method of 240 Hz.

PurposeTo consider the various aspects of this emerging market and to query the traditional view of thick film deposition and processing for successful flexible electronic production.Design/methodology/approachThe current status of flexible electronics is reviewed with particular emphasis on emerging rather than established technologies. New techniques and applications are also discussed. Material and processing developments are also required to meet the new challenges and current developments and future needs are discussed.FindingsMass production of flexible electronic circuits using processing techniques that are more akin to the newspaper printing industry is under way. Much development of both materials and processing is required but needs in the radio frequency identification, renewable energy and display markets among others justify the investment.Research limitations/implicationsDue to the wide range of new applications there is a lack of detail in this review that will necessitate further reading.Practical implicationsThere will need to be a change of thinking in the processing and material choice used in mass production of flexible electronics by any large volume manufacturer of traditional circuits on rigid substrates. Existing, new materials need development for electrical characteristics and ease of use. New materials will undoubtedly be required.Originality/valueThis paper raises awareness and technical issues surrounding emerging technologies.

The resistivity of oil impregnated paper will decrease during its aging process. This paper takes paper resistivity as an assessment index to evaluate the insulation condition of oil impregnated paper in power transformer. The feasibility of this method are discussed in two aspects: reliability and sensitivity. Iterative inversion of paper resistivity was combined with finite element simulation. Both the bisection method and Newton’s method were used as iterative methods. After the analysis and comparison, Newton’s method was selected as the first option of paper resistivity iteration for its faster convergence. In order to consider the spatial distribution characteristic of paper aging and enhance the calculation accuracy, the resistivity calculation is expanded to a multivariate iteration based on Newton’s method, in order to consider the spatial distribution characteristic of paper aging and improve the calculation accuracy. This paper presents an exploratory research on condition assessment of oil impregnated paper insulation, and provides some reference to the security and economy operation of power transformers.

In this paper, we review both ANSI/IEEE and IEC short circuit calculation methods. We discuss and compare terminology, definitions, and calculation approaches. We present the advantages and disadvantages of both standards with numerical examples. We analyze identical systems using both methods to make a side-by-side comparison of the results. After both methods are introduced in detail and understood, arc flash calculation examples will be provided using IEC short circuit calculations. Currently, all arc flash calculation methods (including IEEE 1584) focus on three-phase fault currents without being limited to any specific short circuit standard. In our approach, the IEC method can be effectively used for arc calculations. This approach can be utilized in regions of the world where IEC standards are used for short circuit calculations.

A new method for measuring the elastic properties of paper on-line in a paper machine by using ultrasound has been developed. The unique feature of the method is that a continuous stochastic ultrasonic signal is used for measurements, which is generated by means of a dry friction between a running paper web and a rigidly fixed friction head. The signals from the web are picked up by an array of air-coupled ultrasonic receivers, which have no mechanical contact with the paper web. The ultrasound velocity in the web is obtained by means of the correlation processing. By using advanced digital signal processing, the tensile stiffness index (TSI) of the running web is determined. From the sensor we get the TSI values both in the machine direction and the cross-machine direction. The on-line ultrasonic sensors have been installed on two different paper machines for more than two years. This paper describes the background of the method, as well as some experiences and applications from two mill installations.

A complete model for the internal particle distribution of electrophoretic image displays (EPIDs) is presented. From this model, simulation formulas for electrical and optical properties are calculated. These formulas incorporate both time dependence and voltage dependence. They make it possible to optimize display properties since the model is built up with physical parameters. Results are shown that prove that this model is indeed capable of complete optical and electrical transient simulation. The importance of centrifugation during display manufacturing is proven as a way to improve the switching speed of the display.

The Electronic Shelf Label (ESL) is an electronic display device based on LCD or electronic paper. In this work, we focus on the application of electronic paper display in ESL. We Put forward a kind of driver interface circuit from the electronic shelf label architecture and principle of electronic paper display controller and driver chip; Combined with electronic paper waveforms and SDRAM, we catch the design points of the driver and process; The scheme has been proved to achieve the image display and update with a good reading experience as traditional paper, so it has certain reference significance for electronic shelf label design, and will be beneficial to the popularity of electronic paper application and promotion.

This paper describes the development of a referenced Electrochemical Paper-based Analytical Device (rEPAD) comprising a sample zone, a reference zone, and a connecting microfluidic channel that includes a central contact zone. We demonstrated that the rEPADs provide a simple system for direct and accurate voltammetric measurements that are referenced by an electrode with a constant, well-defined potential. The performance of the rEPADs is comparable to commercial electrochemical cells, and the layout can be easily integrated into systems that permit multiplexed analysis and pipette-free sampling. The cost of this portable device is sufficiently low that it could be for single-use, disposable applications, and its method of fabrication is compatible with that used for other paper-based systems.

Air-gap discharge in oil-paper insulation is one of the main types of partial discharge (PD) in power transformer. The discharge development stage for monitoring and diagnosis of transformer potential faults is a significant area of study. The method of wavelet packet energy entropy, which is based on different frequency bands energy distribution of PD signals at different insulation states, is provided to explore the variation characteristics of the whole PD process. In this paper, air-gap discharge model is built in the simulative transformer tank that collects PD signals based on constant voltage method. This model also utilizes wavelet packet decomposition method to partition PD signal bands obtaining signal energy distribution in each frequency band, as well as total signal energy tendency along with PD development process. Wavelet packet energy entropy, which is the new PD feature parameter describing the development process, represents the order degree of PD signals which corresponds to dielectric strength. Finally, because of the cyclic change of this method, the step points of wavelet packet entropy are taken as the way to effectively divide the PD development stage.

The small-signal equivalent circuit modeling of microwave field-effect transistors (FETs) is an evergreen and ever flourishing research field that has to be up-to-date with technological developments. Hence, modeling techniques must be continuously adapted and extended to suit best evolving technologies. The extraction of a FET high-frequency small-signal equivalent circuit is a very active and broad research area of significant interest, owing to its use as a prerequisite for noise and large-signal modeling. The aim of this invited article is to provide in-depth knowledge, critical understanding, and new insights into how to extract a FET small-signal equivalent circuit from both theoretical and practical perspectives. To illustrate potential solutions to the key challenges faced by researchers, experimental results for different semiconductor technologies are reported and discussed. The study is focused on the hot research topic of the cold approach that has been, and still is, the most widely used technique for extracting FET small-signal models and on the active role of the transconductance for successful modeling. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2016.

The service life of a transformer is determined by the condition of its oil–paper insulation. A modified Cole–Cole model was introduced to describe the frequency domain spectroscopy (FDS) curves based on the classic Debye relaxation model and thereby accurately determined the ageing state of the insulation of a power transformer using FDS. Oil–paper insulation samples with different ageing states are prepared under laboratory conditions, and a characteristic parameter is extracted to quantify their ageing states after a detailed investigation of the frequency domain dielectric properties of the samples. Results reveal that the modified Cole–Cole model, including the α relaxation components, dc and hopping conductivity components, can be employed to effectively model the frequency dielectric characteristics of oil–paper insulation. Furthermore, the extracted characteristic parameter from this model, τα, can be utilized in the quantitative evaluation of the ageing states of transformer insulation. A case example is discussed to demonstrate the applicability of the proposed technique in the condition assessment of field power transformers.

The paper presents new diagnostic method applied to assess aging degree for paper-oil insulation used in professional electrical power device, primarily including medium and high power transformers. The described method is based on modified diagnostics using the recovery voltage effect occurring in dielectrics (RVM – Recovery Voltage Methods). Modification of the RVM method applied so far, which is now used only to assess moistening degree for paper-oil insulation in power transformers, consists in a new parametric analysis of recovery voltage time characteristics. Simulation and experimental tests carried out in laboratory conditions for adequately prepared insulation samples have proven that the time-constant of recovery voltage decay (τR_MIN) is the most susceptible parameter as regards quantitative change in the function of aging of the examined insulation. This conclusion is also confirmed by statistical studies, in which a multi-parameter variance analysis method has been applied. An original equivalent circuit diagram of the insulation has been used to simulate aging degree of paper-oil insulation samples in numerical tests. The diagram is based on the Cole-Cole type dielectric response model.

In this paper, various integration schemes for in-cell capacitive touch panels will be reviewed. Continuous efforts have been made to eliminate the interference between display and touch sensor structure. A in-cell LCD module with self-capacitance touch sensor integrated will be presented.

International audience; This work investigates optimal Degrees of Freedom (DoF) achieving schemes for the MISO Compound Broadcast Channels (BC) where a source is equipped with M antennas, and communicates with 2 single antennas receivers. We develop a modified Dirty Paper Coding scheme that yields the optimal DoF for some Compound MISO BCs in the complex field. This coding scheme offers a “non-linear” alternative to interference alignment at the receivers which yields higher rates in the finite ranges of power. For asymptotic power regimes, it allows for fractional DoF of 1/2, while being of simple formulation and straightforward application to secondary transmissions in Compound Cognitive networks.

This paper is concerned with the task of sensing in web-forming process control loops. Conventional and newly proposed measurement techniques are discussed and a new type of measurement is suggested. The new measurement method adresses the problem of paper machine "wet-end" sensing and is based on a CCD camera system which can detect the dry-line. Both the theoretical and practical aspects of the invention are investigated and the sensing system is developed into a portable measurement system which is applied to a paper machine. The paper machine measurements are analyzed and presented using nonparametric techniques based on analysis of variance. Compared to traditional scanning gauge systems the dry-line detector allows for a large reduction in the transport delay, higher data density and sampling rate, and better machine directional (MD), and cross-directional (CD) signal decomposition.

A universal column driver is implemented in a 0.13-µm highvoltage CMOS process for not only TFT-LCD but also OLED applications. The proposed column driver employs 13-bit linear DAC to cover all gamma curves of display applications and address-based configuration for intra- panel interface protocol to support both TV and IT applications. Measured results demonstrate the average voltage of output channels (AVO) is under 1mv, which satisfies 1-LSB resolution at 18.5V of AVDD.

To increase the efficiency of photovoltaic (PV) systems, maximum power point (MPP) tracking of the solar arrays is needed. Under partially shaded conditions (PSCs), the solar arrays power–current (P–I) characteristic has multiple MPP. This paper presents various methods and approaches of tracking the MPP from a PV generator operating under PSC. Some comparisons, advantages, drawbacks and critical analysis of each method are discussed. It was found that, indirect methods use empirical data or mathematical expressions of numerical approximations to estimate the MPP from the PV generator’s voltage, current and irradiance. Direct methods offer the advantage of obtaining the actual maximum power from the PV generator’s voltage and current. Artificial intelligence methods do not need exact mathematical models. They can perform under parameter variation, load and supply voltage disturbances. Finally, novel methods require less number of iterations to converge, independent to the initial conditions. All t...

In AC installations the Arc Fault Detection Devices are well established. However emerging high power (high current) DC application fields represent several challenges wit respect to arc faults and their detection. This paper presents arc fault signals in time domain and in frequency domain, discusses challenges associated with arc fault detection in the DC application domain and application of the UL1699B standard testing procedure for arc fault detection development in high current applications.