Search

• Water retention curves (WRCs) of municipal solid wastes (MSWs) • Hysteresis of WRCs of MSWs with decomposition. • Effects of decomposition and paper content on the WRCs. • Unsaturated hydraulic and gas conductivity of MSWs. This paper investigates the drying and wetting water retention curves (WRCs) of municipal solid wastes (MSWs) with different paper contents, dry unit weights and degrees of biodegradation (DOBs). Fresh synthetic samples were prepared based on the field composition of the MSWs at Mugga Lane Landfill, the Australian Capital Territory (ACT), Australia. The degraded samples were prepared in simulators with MSWs of different initial dry unit weights and decomposition periods with leachate recirculation. The water retention curves (WRCs) of the MSWs were determined using pressure plate tests, in both drying and wetting phases. The outflow from MSWs was analysed using Gardner's method to obtain the unsaturated hydraulic conductivity. The results indicate that the WRCs of the MSWs are greatly affected by the DOB, paper content and dry unit weight. When DOB < 30 %, as DOB increases, the air-entry pressure of MSWs with paper increases, and the residual moisture content decreases regardless of paper content. With DOB > 30 %, the air entry pressure and residual water content depend on the balance between organic matter and highly decomposed organic constituents. The paper content affects the WRCs of MSWs due to its water retention capacity and change in the particle size distribution with decomposition. The increase in the dry unit weight of MSWs significantly increases the air entry pressure and residual moisture content, similar to the borehole samples with combined effects of biodegradation and increase in stress level from literature. Hysteresis effects have been observed during the drying and wetting of MSWs. The hysteresis of WRCs increases with the paper content and DOB. [ABSTRACT FROM AUTHOR]

Staphylococcus argenteus and Staphylococcus schweitzeri, previously known as divergent Staphylococcus aureus clonal lineages, have been recently established as novel, difficult-to-delimit, coagulase-positive species within the S. aureus complex. Methicillin-resistant strains of S. argenteus are known from Australia and the UK. Knowledge of their epidemiology, medical significance and transmission risk is limited and partly contradictory, hampering definitive recommendations. There is mounting evidence that the pathogenicity of S. argenteus is similar to that of 'classical' S. aureus , while as yet no S. schweitzeri infections have been reported. To provide decision support on whether and how to distinguish and report both species. PubMed, searched for S. argenteus and S. schweitzeri. This position paper reviews the main characteristics of both species and draws conclusions for microbiological diagnostics and surveillance as well as infection prevention and control measures. We propose not distinguishing within the S. aureus complex for routine reporting purposes until there is evidence that pathogenicity or clinical outcome differ markedly between the different species. Primarily for research purposes, suitably equipped laboratories are encouraged to differentiate between S. argenteus and S. schweitzeri. Caution is urged if these novel species are explicitly reported. In such cases, a specific comment should be added (i.e. 'member of the S.aureus complex') to prevent confusion with less- or non-pathogenic staphylococci. Prioritizing aspects of patient safety, methicillin-resistant isolates should be handled as recommended for methicillin-resistant Staphylococcus aureus (MRSA). In these cases, the clinician responsible should be directly contacted and informed by the diagnosing microbiological laboratory, as they would be for MRSA. Research is warranted to clarify the epidemiology, clinical impact and implications for infection control of such isolates. [ABSTRACT FROM AUTHOR]

As a trending mobility choice, e-scooters have become popular in many cities. A number of authorities have initiated shared e-scooter trial schemes to assess the feasibility of the vehicles prior to enacting official legalisation. This paper aims to provide an evidence review of shared e-scooters and investigate how existing evidence may inform long-term policies. This carries significant relevance for jurisdictions that are in a conflicting position with e-scooters, such as New South Wales (NSW), Australia whose context motivates this study. The evidence review focuses on three themes derived from experience with shared e-scooters within the broader micromobility landscape, namely: safety; where shared e-scooters fit into the modal landscape; and the environmental impacts. Findings confirm that ensuring the safety of shared e-scooters requires complex solutions, which may include a clear regulatory framework for e-scooters, safety education and skill training, innovative data collection and analysis methods, and an approach to safety management that is user-based, location-based, and time-based. In terms of modal fit policymakers should encourage first and last-mile combinations with public transport, with consideration of user characteristics; while climate impact is strongly correlated to the mode replaced by e-scooter trips. The paper provides insights for policymakers on the regulation and positioning of shared e-scooters. • Many jurisdictions are struggling to determine policies for e-scooters. • Existing e-scooter evidence sheds light on possible long-term policies. • Safety management should consider different users, locations, and times. • First and last-mile combinations with public transport should be encouraged. • Climate impact is strongly correlated to the mode replaced by e-scooter trips. [ABSTRACT FROM AUTHOR]

When undertaking any study of the isotope abundance values of a bulk material, consideration should be given to the source materials and how they are combined to reach the final product being measured. While it is demonstrative to measure and record the values of clean papers, such as the results published as part one of this series, the majority of forensic casework samples would have undergone some form of writing or printing process prior to examination. Understanding the effects of these processes on the δ13C values of paper is essential for interpretation and comparison with clean samples, for example in cases where printed documents need to be compared to paper from an unprinted suspect ream. This study was undertaken so that the source materials, the effects of the production process and the effects of printing and forensic testing could be observed with respect to 80 gsm white office papers. Samples were taken sequentially from the paper production facility at the Australian Paper Mill (Maryvale, VIC). These samples ranged from raw wood chips through the pulping, whitening and refinement steps to the final formed and packed paper. Cellulose was extracted from each sample to observe both fractionation and mixing steps and their effect on the δ13C values. Overall, the mixing steps were observed to have a larger effect on the isotopic values of the bulk materials than any potential fractionation. Printing of papers using toner and inkjet printing processes and forensic testing were observed to have little effect on δ13C. These experiments highlighted considerations for sampling and confirmed the need for a holistic understanding of sample history to inform the interpretation of results. [ABSTRACT FROM AUTHOR]

• First assessment of paper chromatography using large sample sizes and microbe DNA. • Chromatogram features did not vary consistently with gradients of soil condition. • Results imply context dependent response of chromatogram features to soil condition. • Paper chromatography needs more testing before being embraced for soil assessment. Although paper chromatography is being promoted as a cost-effective tool for rapid assessment of soil health, few studies have explored the quantitative relationship between chromatogram features and soil health variables, and no studies have investigated the association between chromatogram features and microbial diversity as determined using DNA sequences. We assessed 343 soil samples from varying land uses in southwestern Australia to investigate the relationship between total organic carbon, microbial activity and diversity, salinity and pH levels and 12 chromatogram features. Spearman's correlations and variance partitioning were used to detect relationships. Although total organic carbon and microbial activity displayed the strongest correlations with chromatogram features, they were not associated with greater development of radial features and median zone radius as expected. This was in contrast to what has been previously reported, implying context dependent responses of chromatogram features to gradients in soil variables. Microbial community structure was found to explain changes in chromatogram features better than the measured soil variables. These results indicate that further studies are necessary before paper chromatography is embraced as a tool for soil health assessment, and raises questions regarding the use of chromatography by community groups as a tool to measure soil health. [ABSTRACT FROM AUTHOR]

A dedicated grid-tied offshore hybrid energy system for hydrogen production is a promising solution to unlock the full benefit of offshore wind and solar energy and realize decarbonization and sustainable energy security targets in electricity and other sectors. Current knowledge of these offshore hybrid systems is limited, particularly in the integration, component control, and allocation aspects. Therefore, a grid-integrated analytical model with a power dispatch allocation strategy between the grid and electrolyzer for the co-production of hydrogen from the offshore hybrid energy system is developed in this paper. While producing hydrogen, the proposed offshore hybrid energy system supplies a percentage of its capacity to the onshore grid facility, and the amount of the electricity is quantified based on the electricity market price and available total offshore generation. The detailed controls of each component are discussed. A case study considers a hypothetical hybrid offshore energy system of 10 MW situated in a potential offshore off the NSW of Australia based on realistic metrological data. A grid-scale proton-exchange membrane electrolyzer stack is used and a model predictive power controller is implemented on the distributed hydrogen generation scheme. The model is helpful for the assessment or optimization of both the economics and feasibility of the dedicated offshore hybrid energy farm for hydrogen production systems. • Modeling of a grid-integrated analytical model of an OHES for hydrogen co-production. • Development of a power dispatch allocation strategy for the proposed OHES. • Development of detailed controls of each component used in the proposed OHES. • Demonstrations of a case study considering 10 MW OHES situated in offshore off the NSW of Australia. [ABSTRACT FROM AUTHOR]

Temperature cycling stability studies can be appropriately designed and utilized to ensure that drug product quality, efficacy, and safety are not compromised when materials are subjected to short term temperature excursions from intended storage that may occur during e.g., shipping, transport, or patient use. Some countries, such as Australia and Brazil, impose specific regulations that specify the need to conduct stability studies that are supportive of "real world" excursions as part of licensing approval requirements. These temperature cycling stability studies extend beyond what is described in ICH Guidelines Q1A(R2) and Q5C, and companies may be challenged in designing studies that not only satisfy country specific regulations, but also satisfy all global regulatory health authority expectations. This article focuses on responses to a cross-industry survey conducted within the International Consortium for Innovation and Quality (iqconsortium.org) member companies, regarding practices related to temperature cycling stability studies, in order to determine how these requirements are being interpreted and met. The results indicate that while there is no one-size-fits-all approach to performing temperature cycling stability studies, there are common and best practices that can be followed to satisfy global health authority regulatory guidelines and requirements. The purpose of this paper is to describe the outcome of an industry survey and common/best practices on temperature cycling stability studies performed on drug product (DP) to satisfy the requirements established for marketing authorizations in Australia and Brazil or any other countries that may have similar requirements. The framework is proposed within the context of late phase and commercial development of common biological and/or large molecule modalities, such as monoclonal antibodies (mAbs, including bispecific antibodies), fusion proteins, complex proteins, oligonucleotides, and antibody-drug conjugates (ADCs), but many of the general principles involved may be applied to other therapeutics, such as Virus Like Particles (VLP), gene or cell therapies (GTx or CTx), or vaccines. For the purposes of this paper, temperature cycling stability studies refer to studies that are designed, in part, to support short term temperature excursions that drug product may be subjected to during shipping and storage activities and is outside of the labeled storage condition of the product. [ABSTRACT FROM AUTHOR]

• We examined panic buying and hoarding at the onset of the COVID-19 outbreak. • Perceived scarcity was the strongest predictor of panic buying. • Intolerance of uncertainty was the strongest predictor of hoarding. • Buying restrictions imposed by retailers may reduce panic buying. The COVID-19 pandemic led to panic buying in many countries across the globe, preventing vulnerable groups from accessing important necessities. Some reports inaccurately referred to the panic buying as hoarding. Although hoarding is a separate issue characterised by extreme saving behaviour, the two problems may be influenced by similar factors. Participants from Australia and the United States (final N = 359) completed online self-report measures of panic buying, hoarding, shopping patterns, perceived scarcity, COVID-19 illness anxiety, selfishness, and intolerance of uncertainty. Our findings showed that panic buying was related to hoarding symptoms (r 's =.23 -.36), and yet, both were uniquely associated with different psychological factors. Whilst panic buying was most strongly related to greater perceived scarcity (r 's =.38 -.60), hoarding was most related to a general intolerance of uncertainty (r 's =.24 -.57). Based on our findings, future strategies to prevent panic buying should focus on reducing perceived scarcity cues in the community, as this seems to be the primary driver of panic buying. Another preventative strategy to reduce excessive acquiring and saving may be to implement educational programs to increase people's ability to tolerate distress and uncertainty. [ABSTRACT FROM AUTHOR]

Adherence and accuracy of self-monitoring of dietary intake influences success in weight management interventions. Information technologies such as computers and smartphones have the potential to improve adherence and accuracy by reducing the burden associated with monitoring dietary intake using traditional paper-based food records. We evaluated the acceptability and accuracy of three different 7-day food record methods (online accessed via computer, online accessed via smartphone, and paper-based). Young women (N=18; aged 23.4±2.9 years; body mass index 24.0±2.2) completed the three 7-day food records in random order with 7-day washout periods between each method. Total energy expenditure (TEE) was derived from resting energy expenditure (REE) measured by indirect calorimetry and physical activity level (PAL) derived from accelerometers (TEE=REE×PAL). Accuracy of the three methods was assessed by calculating absolute (energy intake [EI]–TEE) and percentage difference (EI/TEE×100) between self-reported EI and TEE. Acceptability was assessed via questionnaire. Mean±standard deviation TEE was 2,185±302 kcal/day and EI was 1,729±249 kcal/day, 1,675±287kcal/day, and 1,682±352 kcal/day for computer, smartphone, and paper records, respectively. There were no significant differences between absolute and percentage differences between EI and TEE for the three methods: computer, –510±389 kcal/day (78%); smartphone, –456±372 kcal/day (80%); and paper, –503±513 kcal/day (79%). Half of participants (n=9) preferred computer recording, 44.4% preferred smartphone, and 5.6% preferred paper-based records. Most participants (89%) least preferred the paper-based record. Because online food records completed on either computer or smartphone were as accurate as paper-based records but more acceptable to young women, they should be considered when self-monitoring of intake is recommended to young women. [ABSTRACT FROM AUTHOR]

It is generally accepted that the amino acid reagent consisting of 1,2-indanedione and a catalytic amount of zinc chloride, referred to as IND-Zn, is the single best method for the detection of latent fingermarks on paper substrates and that ninhydrin is of limited value when used in sequence after this reagent. However, recent research has suggested that the sequence 1,8-diazafluoren-9-one (DFO) followed by ninhydrin may actually produce a greater number of fingermarks than IND-Zn on its own or IND-Zn followed by ninhydrin. This study focussed on the evaluation of two fingermark detection sequences for porous surfaces: (1) IND-Zn followed by ninhydrin, physical developer (PD) and the lipid stain nile red; and (2) DFO followed by ninhydrin, PD and nile red. The evaluation was undertaken using a range of latent fingermark donors and on a number of paper substrates that are commonly encountered in Australia. In addition, a pseudooperational trial was completed on 5-year-old university examination booklets. Parallel studies were undertaken at two locations: Sydney (temperate, coastal climate) and Canberra (relatively dry, continental climate). The results of the donor study indicated that there was a negligible difference in performance between the two sequences across all paper types and all time periods evaluated. When considering individual reagents, IND-Zn generally developed better quality fingermarks compared to DFO; however, ninhydrin had a greater enhancement effect on DFO developed marks than after IND-Zn. In the pseudooperational trials, the IND-Zn sequence outperformed the DFO sequence. Nile red did not develop any additional marks at the end of each sequence and, as a result, the use of this technique at the end of a full sequence is of questionable value. The overall outcome was that the sequence IND-Zn followed by ninhydrin and PD is recommended for the processing of common paper substrates under the conditions typically experienced at the two locations studied. [ABSTRACT FROM AUTHOR]

Abstract: Purpose: To describe the paper-based and electronic formats of resident admission forms used in several aged care facilities in Australia and to compare the extent to which resident admission information was documented in paper-based and the electronic health records. Methods: Retrospective auditing and comparison of the documentation quality of paper-based and electronic resident admission forms were conducted. A checklist of admission data was qualitatively derived from different formats of the admission forms collected. Three measures were used to assess the quality of documentation of the admission forms, including completeness rate, comprehensiveness rate and frequency of documented data element. The associations between the number of items and their completeness and comprehensiveness rates were estimated at a general level and at each information category level. Results: Various paper-based and electronic formats of admission forms were collected, reflecting varying practice among the participant facilities. The overall completeness and comprehensiveness rates of the admission forms were poor, but were higher in the electronic health records than in the paper-based records (60% versus 56% and 40% versus 29% respectively, p <0.01). There were differences in the overall completeness and comprehensiveness rates between the different formats of admission forms (p <0.01). At each information category level, varying degrees of difference in the completeness and comprehensiveness rates were found between different form formats and between the paper-based and the electronic records. A negative association between the completeness rate and the number of items in a form was found at each information category level (p <0.01), i.e., more data items designed in a form, the less likely that the items would be completely filled. However, the associations between the comprehensiveness rates and the number of items were highly positive at both overall and individual information category levels (p <0.01), suggesting more items designed in a form, more information would be captured. Conclusion: Better quality of documentation in resident admission forms was identified in the electronic documentation systems than in previous paper-based systems, but still needs to be further improved in practice. The quality of documentation of resident admission data should be further analysed in relation to its specific content. [Copyright &y& Elsevier]

Green hydrogen, produced from renewable electricity, can be transported long distances in multiple mediums. In this paper, a Techno-economic model is proposed to show the economic viability of global green hydrogen transport along 15 major regional routes such as Australia to Asia and Europe for the first time. A Monte Carlo-based technique is presented to assess the levelised cost of green hydrogen for different regions for the next 30 years. Depending on the specific route, green hydrogen can be transported in different forms, including ammonia, Liquid Organic Hydrogen Carrier (LOHC), Hydrogen Slush, compressed or liquefied hydrogen, etc. form and using different modes including shipping, truck, train, and pipeline. A linear programming analysis has been conducted for different regions, showing that among the global projected 300Mt of green hydrogen demand in 2050, 85% will need to be transported between regions to achieve the most economically optimal distribution. • Techno-economic analysis of green H 2 export via 15 worldwide regional trade routes. • Export model includes H2 generation, conversion, transport, and carbon prices. • In 2030, North America will be the largest exporter, followed by Australia. • Higher carbon prices allow for rapid growth in the green hydrogen industry. • Shipping is the most likely and cheapest H 2 export mode for distant transport. [ABSTRACT FROM AUTHOR]

Supporters of hydrogen energy urge scaling up technology and reducing costs for competitiveness. This paper explores how hydrogen energy technologies (HET) are perceived by Australia's general population and considers the way members of the public imagine their role in the implementation of hydrogen energy now and into the future. The study combines a nationally representative survey (n = 403) and semi-structured interviews (n = 30). Results show age and gender relationships with self-reported hydrogen knowledge. Half of the participants obtained hydrogen information from televised media. Strong support was observed for renewable hydrogen, while coal (26%) and natural gas (41%) versions had less backing. Participants sought more safety-related information (41% expressed concern). Most felt uncertain about influencing hydrogen decisions and did not necessarily recognise they had agency beyond their front fence. Exploring the link between political identity and agency in energy decision-making is needed, with energy democracy a potentially productive direction. • Hydrogen's strongest appeal to Australians is its benefit for climate change mitigation. • Although widely accepted, there is limited knowledge about hydrogen in terms of how it is produced or used. • The more people know about hydrogen, the more willing they are to participate in the decision-making process. [ABSTRACT FROM AUTHOR]

Travel Demand Management (TDM) initiatives are widely applied by transport planners to establish and enable appropriate use of critical transport infrastructure. Less attention has been given to the specific case of TDM in an education precinct (university) context. Travel Plans have been promoted as a means for an organisation to encourage sustainable travel choices by their employees, visitors and customers. This paper offers an empirical contribution to the literature through a comparative qualitative evaluation of selected University Sustainable Travel Plans (USTPs) in Australia to identify the most important questions that a USTP should address explicitly. The evaluation comprised identification of a set of evaluation questions, completion of a template for each USTP considered and application of a simple scoring exercise. We also identify TDM measures that have been introduced as part of a USTP in response to the typical travel patterns exhibited in university settings. A contribution of this paper is to create a means of comparison of USTPs and to establish the components of a comprehensive travel plan. • Conducts a comparative analysis of University Sustainable Travel Plans. • Explores international experience of Travel Demand Management (TDM) in an education precinct context. • Key components of University Sustainable Travel Plans are identified. • The important role of regular surveys of staff and student travel behaviour is highlighted. [ABSTRACT FROM AUTHOR]

Significant advances have been made in artificial intelligence technology in recent years. Many health care applications have been investigated to assist clinicians and the technology is close to being integrated into routine clinical practice. The high prevalence of cardiac disease in Australia places overwhelming demands on the existing health care system, challenging its capacity to provide quality patient care. Artificial intelligence has emerged as a promising solution. This discussion paper provides an Australian perspective on the current state of artificial intelligence in cardiology, including the benefits and challenges of implementation. This paper highlights some current artificial intelligence applications in cardiology, while also detailing challenges such as data privacy, ethical considerations, and integration within existing health infrastructures. Overall, this paper aims to provide insights into the potential benefits of artificial intelligence in cardiology, while also acknowledging the barriers that need to be addressed to ensure safe and effective implementation into an Australian health system. [ABSTRACT FROM AUTHOR]

Abstract: Coalbed methane (CBM) or coal seam gas (CSG) as it is known in Australia is becoming an increasingly important source of energy around the world. Many countries such as United States, Canada, Australia and China are investing in the CSG industry. A rise in the cost of conventional natural gas and many other energy resources, along with a decline in these conventional resources and issues such as climate change have encouraged a global interest in alternative sources of energy like CSG. The estimated quantity of CSG worldwide is around 1.4×1014 m3, it is clear that coal seam gas is a significant source of energy. The first section of this paper will discuss the production size of CSG worldwide and the future of the industry. The usage of the coal bed seam for the sequestration of CO2 is also an added benefit. The reduction of CO2 released to the environment may help in the future mitigation of global warming. In addition, the re-injecting of the co-produced CO2 enhances the commercial recovery and production of CSG wells. In the second section, the impact of the CSG industry's by-products on the environment, the freshwater ecosystem and human health are analysed. The second section includes issues associated with the large volume of co-produced water with undesirable composition in the CSG industry. The management of this enormous amount of water requires cost effective technologies and methods. Many methods for dealing with water problems are discussed and analysed in this paper. [Copyright &y& Elsevier]

A lifecycle assessment to estimate greenhouse gas emissions in Australia from the paper cycle is summarised. The greenhouse gas emissions from paper in Australia in 1999/2000 were estimated to be 12.1 million tonnes (Mt) of CO2 equivalent. Nearly half of this amount consisted of CH4 emissions from landfilled waste paper. Various waste management options were modelled to investigate the greenhouse impact of a tonne of paper over its whole lifecycle. Options that keep paper out of landfills significantly reduce greenhouse emissions, waste-to-energy recovery being most effective. Recycling is also beneficial, and is of particular interest from a management perspective because it can be controlled by the pulp and paper industry. These findings can be extended to other wood-based and organic wastes. [Copyright &y& Elsevier]

This paper explores the skills landscape of the emerging green hydrogen industry in Australia drawing on data collected from a study that gathered insights on training gaps from a range of hydrogen industry participants. A total of 41 industry participants completed a survey and 14 of those survey respondents participated in industry consultations. The findings revealed widespread perceptions of training and skilling as being very important to the industry, but under-provisioned across the sector. Data were analysed to consider the problem of skilling the green hydrogen industry and the barriers and enablers as perceived by industry stakeholders. In this paper we argue that urgent cross-sector attention needs to be paid to hydrogen industry training and skill development systems in Australia if the promise of green hydrogen as a clean energy source is to be realised. • Cross-sector collaboration is needed to support education and training on hydrogen energy. • Insufficient training is available to support skill development in hydrogen energy. • Training on electrolysers, fuel cells, hydrogen storage and refuelling stations is most needed. [ABSTRACT FROM AUTHOR]

An effective cleaner production programme requires the efficient collection and interpretation of data relating to a facility’s activities, including information of pollutant emissions, wastes generated and raw materials consumed. Many of these data are required to be collected and reported under national Pollutant Release and Transfers Registers (PRTRs) which are an increasingly common environmental policy tool in the OECD countries.This article considers the relationship between cleaner production and PRTR reporting, and discusses whether cleaner production programmes can be enhanced by the use of PRTR data. A case-study of a fertiliser manufacturing facility reporting under the Australian National Pollutant Inventory (NPI) is used to analyse and illustrate the practical issues around linking cleaner production with PRTR reporting.PRTR reporting can assist in identifying cleaner production opportunities and in generating the data sets required to design, implement and monitor cleaner production programmes. There are, however, some limitations in PRTR data that need to be recognised. Specifically, these are issues around data quality and comparability (e.g. PRTRs rely heavily on default emissions factors rather than the monitoring data that are generally required for cleaner production programmes) and the different data sets required for PRTR reporting (which generally require reporting at the site level rather than at the individual process unit level that is required for cleaner production). [Copyright &y& Elsevier]

• Innovative phenotype-genotype association analysis for categorical genomic data having non-ignorable missing values. • Statistical learning method of random forest is used for variable selection in the analysis. • Weighted logistic ridge regression with EM algorithm is used for missing data imputation in the analysis. • Linear statistical hypothesis testing is used for determining the missingness mechanism in the analysis. • An application to analyzing real data from Australia breast cancer genome-wide association study (GWAS). Genomic data arising from a genome-wide association study (GWAS) are often not only of large-scale, but also incomplete. A specific form of their incompleteness is missing values with non-ignorable missingness mechanism. The intrinsic complications of genomic data present significant challenges in developing an effective and efficient procedure of phenotype-genotype association analysis by a statistical variable selection approach. In this paper we develop a coherent procedure of categorical phenotype-genotype association analysis, in the presence of missing values with non-ignorable missingness mechanism in genomic data. It is developed by integrating the statistical learning methods of random forest for variable selection, joint weighted logistic ridge regression with EM algorithm for missing data imputation, and linear statistical hypothesis testing for determining the missingness mechanism. Two simulated genomic datasets are used to undertake the phenotype-genotype association analysis by the proposed procedure, with the performance validated. The proposed procedure is then applied to analyze a real data set from breast cancer GWAS. [ABSTRACT FROM AUTHOR]

This paper examines the role of socioeconomic status (SES) in affecting access to care and the survival of acute myocardial infarction (AMI) patients in Australia's universal health care system. We jointly model the probabilities of patients being admitted to a catheterisation-capable hospital, receiving invasive coronary angiography (ICA), and surviving 30 days post discharge as a recursive system of probit equations. We further investigate the role of capacity and whether the access gap between SES groups widens when capacity becomes limited. Our study shows that SES plays a significant role in affecting the survival of AMI patients, both directly and indirectly through healthcare access. We find that socioeconomically disadvantaged patients are less likely to gain access to crucial services like catheterisation hospitals and ICA, which indirectly affects their survival probability in addition to the adverse direct impact of SES. While healthcare capacity showed no overall effect on access, its interplay with SES exacerbates the access disparity in situations of limited capacity. Our findings suggest that, to reduce inequality in health outcomes, public health strategy needs to focus not only on enhancing access but also addressing the direct consequences of SES. [ABSTRACT FROM AUTHOR]

To clarify and elaborate on the choices that were made in the development of the Patient Scale of the Patient and Observer Scar Assessment Scale 3.0 (POSAS 3.0), based upon the rich information obtained from patients during focus groups and pilot tests. The discussions described in this paper are a reflection of the focus group study and pilot tests that were conducted in order to develop the Patient Scale of the POSAS3.0. The focus groups took place in the Netherlands and Australia and included 45 participants. Pilot tests were performed with 15 participants in Australia, the Netherlands, and the United Kingdom. We discussed the selection, wording and merging of 17 included items. Additionally, the reason for exclusion of 23 characteristics are given. Based upon the unique and rich material of patient input obtained, two versions of the Patient Scale of the POSAS3.0 were developed: the Generic version, and the Linear scar version. The discussions and decisions taken during the development are informative for a good understanding of the POSAS 3.0 and are indispensable as a background for future translations and cross-cultural adaptations. • The Patient Scale was meant to be concise, readily assessable, quick, and user-friendly instrument assessing the key attributes of scar quality. • Two versions have been developed, the Generic version (total of 16 items), and the Linear scar version (total of 17 items). • Eight of the identified characteristics were merged into three included items. • Twenty-three characteristics were excluded during different phases of the development process for multiple reasons. [ABSTRACT FROM AUTHOR]

Green steel, produced using renewable energy and hydrogen, presents a promising avenue to decarbonize steel manufacturing and expand the hydrogen industry. Australia, endowed with abundant renewable resources and iron ore deposits, is ideally placed to support this global effort. This paper's two-step analytical approach offers the first comprehensive assessment of Australia's potential to develop green steel as a value-added export commodity. The Economic Fairways modelling reveals a strong alignment between prospective hydrogen hubs and current and future iron ore operations, enabling shared infrastructure development and first-mover advantages. By employing a site-based system optimization that integrates both wind and solar power sources, the cost of producing green steel could decrease significantly to around AU$900 per tonne by 2030 and AU$750 per tonne by 2050. Moreover, replacing 1% of global steel production would require 35 GW of well-optimized wind and solar photovoltaics, 11 GW of hydrogen electrolysers, and 1000 square kilometres of land. Sensitivity analysis further indicates that iron ore prices would exert a long-term influence on green steel prices. Overall, this study highlights the opportunities and challenges facing the Australian iron ore industry in contributing to the decarbonization of the global steel sector, underscoring the crucial role of government support in driving the growth and development of the green steel industry. [Display omitted] • Australia could produce low-cost green steel for value-added export • Strong correlation between hydrogen hubs and iron ore operations • Existing infrastructure supports the roll-out of the industry • Optimized generation mix reduces storage, curtailment and production costs • Iron ore prices substantially influence green steel prices in the long term [ABSTRACT FROM AUTHOR]

• Good documentation practice is the foundation for promoting medication safety in young population. • Study identified poor documentation practice through paper and electronic means of medical records. • Newly introduced electronic medical records did not improve the rates of metabolic monitoring nor the quality of documented monitoring. • Youth are at significant risk for antipsychotic induced metabolic syndrome the repercussion of which may impact years of productivity. • Potentially electronic health records could provide health workers with real-time information access, and develop accurate, relevant and structured information thereby adhering to clinical evidence. Since the development of digital records, claims have been made that they improve audits. Clinical audits play important role in evaluation of evidence-practice gaps. Antipsychotic medications are one of the commonly prescribed group of drugs in severe adverse mental conditions. Youth and young people are highly prone to develop drug induced metabolic syndrome. Present study evaluated the extent of data documentation on evidence for metabolic monitoring of antipsychotics and compared paper based to electronic records with good documentation standards. First phase of this study involved a retrospective clinical audit of paper-based documentation on the extent of documentation of weight (primary outcome); lipid and blood glucose (secondary outcomes) of youth prescribed atypical antipsychotics. This was undertaken in three public mental health clinics and a public/private developmental service in Australia based on paper-based documentation. The second phase included auditing electronic data capture from one community clinic. Evidence of documentation was compared with practice standards and published clinical audits (adherence rate benchmark: 40–60%). A total of 310 cases were assessed of which 51 and 37 cases met the eligibility criteria for paper-based and electronic based audit respectively as a component of clinical audit. Evidence of paper documentation of weight was 43% among participants and was comparable with other published clinical audits (p = 0.07) with poor monitoring rates for other blood tests. Findings revealed poor rate of documentation at 35.1% (13 cases), 5.4% (2 cases) and 8.1% (3 cases) for weight, lipid assessments and glucose monitoring, respectively based on electronic records. Present study demonstrate lack of good documentation practices on metabolic monitoring of youth prescribed antipsychotics. It appears transitioning from paper to electronic records did not impact the rate of increase in documentation of metabolic monitoring. This study recommends inclusion of e-monitoring icon with built in metabolic monitoring chart as a component of youth prescribed antipsychotic case records. Good documentation practice is a first step in determination of causality of antipsychotics induced metabolic syndrome. Appropriate strategies to a user-friendly electronic reminder system will be crucial to address on the mechanistic of documentation. [ABSTRACT FROM AUTHOR]

Developing a thriving hydrogen industry will depend on public and community support. Past research, mainly focusing on the acceptance of hydrogen fuelling stations and cars, suggests that people generally support hydrogen energy technology (HET). Few studies have, however, considered how people think about other components of the hydrogen supply chain (i.e., technologies required to make, store, transport and use hydrogen). Moreover, there has been limited research investigating how people interpret and develop beliefs about HET after being presented with technical information. This paper attempts to address these research gaps by presenting the findings from four face-to-face focus group discussions conducted in Australia. The findings suggest that people have differing views about HET, which depends on the type of technology, and these views influence levels of support. The study also revealed concerns about a range of other factors that have yet to be considered in hydrogen acceptance research (e.g., perceived water use, efficiency and indirect benefits). The findings highlight the value of qualitative research for identifying salient beliefs that shape attitudes towards HET and provide recommendations for future research and how to effectively communicate with the public and communities about an emerging hydrogen industry. • Focus group discussions with Australians about whole hydrogen supply chain. • Generally positive, but tentative, attitudes toward hydrogen overall. • Stronger support for industrial applications over domestic/household applications. • Concerns raised about hydrogen's efficiency and its conflict with other technologies. • Support for more research and pilot projects to provide tangible evidence. [ABSTRACT FROM AUTHOR]

Hydrogen supplying to industrial users is currently the major hydrogen business worldwide and the demand for hydrogen is almost entirely supplied from fossil fuels. In the last years a widespread interest on hydrogen has grown as energy vector for the decarbonization of multiple sectors, including industry, transport and buildings. Nevertheless, the impact of natural gas and other fossil fuels substitution with hydrogen is highly affected by the mix of different technologies and energy sources applied for hydrogen generation. The paper aims to investigate current CO 2 emissions related with hydrogen generation in Australia and Italy by means of PEM and alkaline technologies; and to evaluate the potential impact considering cell characteristics variation and 3 scenarios based on energy mix. A sensitivity analysis is performed to identify the critical parameters. Based on experimental data, the energy consumption for hydrogen production using PEM technology is more sensitive to cell voltage compared to current density, which indicates the importance of cell manufacturing and electrolyte resistance. In addition, by performing sensitivity analysis regarding energy sources scenarios it is found that carbon dioxide emission in Australia is more sensitive to renewable energy sources rather than Italy. [Display omitted] • Importance of manufacturing and electrolyte resistance because of high PEM energy consumption sensitivity to cell voltage. • Predicted emission in 2030 is 5–10 kg CO 2 using PEM/alkaline technology in Italy. • 18% reduction of national electricity grid CO 2 emission in Australia is predicted. (In 2030 in comparison to 2019). [ABSTRACT FROM AUTHOR]

• Qualitative study with participants in Australia's largest Connected Intelligent Transportation Systems field trial. • Participants were generally positive towards the system and expressed interest in future adoption of the technology. • Participants expressed desire for increased personalisation of system settings. • Participants expressed some concerns about timing and accuracy of some information provided. • Participants expressed desire for appropriate data privacy and confidentiality controls and use of the data. The Ipswich Connected Vehicle Pilot (ICVP) was the largest on-road trial of connected vehicle technology in Australia. In the ICVP, 355 privately-owned vehicles were outfitted with connected vehicle technology and driven for 9 months with 326 participant vehicles remaining in the study until completion. User acceptance is as a key determinant of the future effectiveness of connected and co-operative Intelligent Transport systems (C-ITS) given it impacts likely uptake of these vehicles and the optimal functioning of such systems is contingent on widespread uptake by the public. This paper presents the findings of two qualitative studies conducted as part of the ICVP, comprising 53 individual interviews and 14 focus groups/interviews with 47 participants. The purpose of the qualitative studies was to understand users' perceptions of the system as well as their acceptance of C-ITS in general. Overall, participants were generally positive towards the system, could appreciate the safety benefits it offers, and expressed interest in adopting the technology presuming future systems would be refined. Some participants reported that they missed the warnings provided by the system once the technology had been removed. Participants wanted the system to be seamlessly integrated in their vehicle and have features that enabled personalisation. Participants identified that some of the warnings, most notably the advanced red light warning, were presented too late or at inaccurate times indicating that these issues must be remedied to ensure successful future implementation of C-ITS. Participants appreciated that data sharing would optimise the system but wanted controls to be put in place to guard against misuse; participants did not want their data to be used for sales or marketing purposes. Users' experience and perceptions are key to ensuring wider-spread adoption of C-ITS. The findings thus have important implications for future C-ITS implementation to ensure that the benefits of C-ITS are optimised to facilitate wide-spread penetration of the technology. [ABSTRACT FROM AUTHOR]

While many countries have experienced more than one wave of the pandemic throughout 2020, Australia has been able to contain the virus in a way that makes it a stand out (with New Zealand) in the way that it has been contained, with an exception in Victoria linked to failed quarantine procedures for travellers returning from overseas. Through descriptive analysis, this paper builds on earlier papers by the authors on the Australian response, with a focus on the changing dynamics of travel activity, concern with public transport, and attitudes surrounding activity given the perception of risk of COVID-19 and the level of public support for regulatory intervention and restrictions on movement. We find that Australia continues to suppress travel, particularly that for commuting, that comfort in completing day-to-day activities continues to rise (with the exception of Victoria where confidence feel significantly), and while support for intervention measures remains high, there has been an erosion in sentiment. As with previous work, we discuss what this might mean for future transport policy, and attempt to draw lessons from the Australian experience. [Display omitted] [ABSTRACT FROM AUTHOR]

This paper (Part 2 in the paper series), building on earlier studies examining the Australian response, extends on findings related to travel activity, commuting, and attitudes towards COVID-19 measures (Part 1 in the paper series). In this paper we focus in detail on the impact of, and experiences with, working from home (WFH), perhaps the largest of the positive unintended consequence of the pandemic, with respect to transport, and a key lens through which the changing patterns in travel activity and attitudes discussed in Part 1 need to be understood. We conclude that through the widespread adoption of WFH as a result of nationwide public health orders, there is evidence emerging that WFH is now seen as an appealing instrument of change by employees and employers, there is growing support to continue to support WFH into the future. This represents a significant potential contribution to the future management of the transport network, especially in larger metropolitan areas. We also discuss policy implications of this result and what the international community may take from the Australian experience. [ABSTRACT FROM AUTHOR]

Hydrogen is a potential future solution addressing global warming, climate change, and energy security challenges. It efficiently allows for storing excess renewable energy and generating heat and electricity without increasing greenhouse gas emissions. It can create a practical pathway to replace fossil fuel vehicles and move toward a net-zero transport sector. Various hydrogen strategies and industry roadmaps have been developed to identify key goals, set targets for progress, and develop strategic plans to remove barriers. As identified through these documents, the development of consistent national and international codes and standards and the creation of clear procedures and regulations are essential for the safe implementation and adaptation of hydrogen systems, leading to the successful process of hydrogen sector. This paper provides a comprehensive and critical review of the different aspects of hydrogen safety to advance hydrogen regulations, codes, and standards. While it summarises the key international hydrogen frameworks, the main focus of the paper is on Australian plans, progress, and working groups for hydrogen deployment that will help future green energy society. • The safety developments affect the cost of Australian hydrogen scaling targets. • Training and safety developments are essential to achieve public trust in Australia. • Better community engagement is needed to move from hydrogen planning to its development. • Data-based tools assist the development of hydrogen safety procedures in Australia. [ABSTRACT FROM AUTHOR]

The aim of this paper is to investigate the empirical correlations between inter-city population distribution, intra-city urban economic structures, and networked inter-city relationships to propose a conceptual classification framework for the Australian urban system. This paper sets the pre-COVID-19 benchmark for future research which will investigate the impact of COVID-19 on the economic geography of the Australian urban system. This research confirms that the form of Australia's urban structure is informed by a combination of population distribution, economic concentration, specialisation and diversity of industries and occupations, and networks between cities. Based on these results, we propose an urban structure framework characterised by hierarchical sub-systems and typologies of cities. The framework consists of standalone regional centres and larger cities which form a networked megaregion. Additionally, we propose five typologies of cities based on their functional roles. The Australian urban system presents a unique hybrid economic geography where its structure of networked megaregions of cities and standalone regional centres each with its complementary functional roles, presents itself an interesting case study to inform population policies for other geographies. • This study proposes a method to synthesise city size, economic structure and their networked relationships. • Principles of economic agglomeration mostly apply within the Australian context however, there are nuances and exceptions. • Proximity has a role to play when determining the economic roles of cities and the strength of interactions between cities. • Two urban sub-systems exist in Australia: standalone regional centres and megaregions. • Five city types in Australia which considers their size, economic structure and geography. [ABSTRACT FROM AUTHOR]

This paper reports on an energy/exergy analysis of a standalone solar-hydrogen system with a metal hydride (MH) system thermally managed using a phase change material (PCM). This is a self-contained thermal management arrangement that stores the heat released from the MH unit, when it is being charged and transfers it back to the MH while discharging hydrogen. The first and second laws of thermodynamics were used to develop a mathematical model in MATLAB to simulate this system and quality its performance from the energy and exergy viewpoints. The model was then applied on a passive standalone house, with ∼3.8 MWh/year electricity demand, located in southeast Australia. The exergy efficiencies of the solar PV, electrolyser, fuel cell and the whole solar hydrogen system were found to be 6.5%, 88%, 50.6%, and 3.74%, respectively. The paper also provides the detailed entropy generation and exergy analysis on the MH hydrogen storage unit together with its PCM-based thermal management arrangement. The results show that the annual entropy generation, exergy destruction and exergy efficiency of the MH hydrogen storage unit were 173 Wh/K, 51.5 kWh, and 98.8%, respectively. • Exergy analysis of phase change material used for metal hydride thermal management in solar hydrogen system. • The energy and exergy efficiencies of the solar PV are around 6.1% and 6.5%, respectively. • Energy and exergy of solar-hydrogen system were 3.48% and 3.74%, respectively. • Exergy efficiency of the MH thermal management using PCM was 98.8%. [ABSTRACT FROM AUTHOR]

Investment in the hydrogen economy is increasing at unprecedented rates. To ensure a swift transition, understanding the diverse perspectives of and how to work collaboratively with all sectors of society is needed. In doing so, how industry stakeholders understand community perceptions and view their role in mediating perceived issues needs to be better understood. Therefore, this study aims to investigate how industry assumptions of community perspectives of hydrogen technologies compare and contrast with those in an Australian context. Using inductive thematic analysis, this exploratory project analysed 45 publicly-available submissions received in 2019 for the National Hydrogen Strategy from the industry perspective, and 62 public submissions received in 2019–2020 for the Victorian Green Hydrogen Discussion Paper from the community perspective. Results show that industry stakeholder assumptions about community concerns tended to reflect specific technical issues as opposed to those reported by the community: moral obligations to climate, environment, and future generations. Findings indicate that further work is needed to better align industry understandings and characterisations of the broader public. Several practical implications for the energy sector are noted. First, hydrogen is unlikely to be immune to community concerns faced by other energy projects; therefore, a robust plan for community inclusion that considers a range of complex, contextual factors is required. Second, there is an opportunity for the formation of a more collaborative approach, which integrates industry and community goals and values. Third, industry and government may benefit from viewing the community as an under-utilised, valuable partnership or resource rather than an object to be managed as part of a development process. We contend that a collaborative framework, including approaches such as co-design and shared identity formation may be critical to furthering the hydrogen agenda. • This study explores community and industry perspectives to advance hydrogen economy. • Worldviews and values informed perspectives of industry and community stakeholders. • Community perspectives were driven by future and greenhouse gas emission concerns. • Industry assumed community would be most concerned about the safety of hydrogen. • Results indicate that community and industry should be involved in unison. [ABSTRACT FROM AUTHOR]

Computed tomography coronary angiography (CTCA) is a non-invasive diagnostic modality that provides a comprehensive anatomical assessment of the coronary arteries and coronary atherosclerosis, including plaque burden, composition and morphology. The past decade has witnessed an increase in the role of CTCA for evaluating patients with both stable and acute chest pain, and recent international guidelines have provided increasing support for a first line CTCA diagnostic strategy in select patients. CTCA offers some advantages over current functional tests in the detection of obstructive and non-obstructive coronary artery disease, as well as for ruling out obstructive coronary artery disease. Recent randomised trials have also shown that CTCA improves prognostication and guides the use of guideline-directed preventive therapies, leading to improved clinical outcomes. CTCA technology advances such as fractional flow reserve, plaque quantification and perivascular fat inflammation potentially allow for more personalised risk assessment and targeted therapies. Further studies evaluating demand, supply, and cost-effectiveness of CTCA for evaluating chest pain are required in Australia. This discussion paper revisits the evidence supporting the use of CTCA, provides an overview of its implications and limitations, and considers its potential role for chest pain evaluation pathways in Australia. [ABSTRACT FROM AUTHOR]

This is the fourth in a series of papers that provides an historical record in this journal of contributions made by the most influential figures in the field of stuttering. Ann Packman is an Australian researcher who will retire shortly. This paper reflects on her long and productive career, and her contributions to the field. With a background in literature, linguistics, philosophy, psychology, and the brain and language, she became well equipped to contribute to understanding stuttering causality. That work, and an accompanying collection of basic and applied clinical research, was constantly grounded with the thoughts and feelings of those who stutter in the community. • Ann Packman is an Australian researcher who will retire shortly. • This paper reflects on her career and her contributions to the field. • Her work was grounded with the thoughts and feelings of those who stutter. [ABSTRACT FROM AUTHOR]

The understanding of the stratigraphic evolution of marine rift basins is important for both "pure" scientific and economic reasons. From a hydrocarbon exploration point of view the main goal is to develop tools to predict reservoir location, quality, and extent. Stratigraphic models try to do that, and only historical cases can be used to test those models. On the other hand, depositional model cannot precisely predict reservoir location as factors unique to the specific basin under analysis affect sediment distribution (basin physiography, type of flows, among others). This aspect can be assessed only on a case-by-case basis and can be used for initial hypothesis generation based on analogues. This paper shows a case history study based on the integration of well logs, and 3D seismic data across the Eastern Dampier sub-basin, Northwester Shelf of Australia. Advanced seismic interpretation techniques, calibrated to well data, enable the definition of a chrono-stratigraphic framework of the late syn-rift sequence (Late Jurassic) of the Lewis Trough, and the description of the sediment distribution through the interpretation of geomorphological features. During the Late Jurassic three different channel systems deliver sandstones to the deep-water part of the basin through multiple entry points. The timing of the sediment input seems to be linked to variation of sediment input as during that time relative sea-level was slowly rising. The location of the entry points is related to local physiography and defies any attempt of prediction based on general "rules." From a stratigraphic point view, the findings of the study support the idea that, in rift basin, mechanical subsidence is the primary control for accommodation space, with episodic pulses of extension followed by longer periods of tectonic quiescence. It is during these episodic movements along the basin's bounding faults that space for sedimentation is created. This interpretation is in striking contrast with the basic assumptions of the conventional sequence stratigraphy model. • Understanding the stratigraphic evolution of marine rift basins allows to predict reservoir location and extent. • The present paper analyzes the late syn-rift succession of the Lewis Trough to reconstruct the stratigraphic evolution of the basin infill. • Accommodation space in the Lewis Trough is primarily controlled by mechanical subsidence related to asymmetrical fault movement. • Turbiditic sedimentation occurs during sea-level rise, and it is related to an Increase in sediment supply. • IConventional sequence stratigraphic modeling cannot be applied to rift-basins. [ABSTRACT FROM AUTHOR]

• This paper presents a review on the state-of-the-art electric vehicle charging technologies i.e., fast, super-fast, and ultra-super-fast charging stations that are under development. These have the potential to cause power quality issues such as charging transients, rapid voltage fluctuations, and harmonics in the power grids. • EVs can participate as mobile storage to provide vehicle-to-grid (V2G) support and ancillary services. There are still some barriers to the wide implementation of V2G systems. This paper has highlighted these issues and their impacts to power grids. • This paper investigates the impacts of random and fluctuating EV fast-charging loads on the electric power grids, mainly considering the random connection of EVs to the power grids through DC fast-charging stations as the principal source of fluctuating EV loads. • The charging stations are modeled for three different commercial DC fast charger connections (CHAdeMO, SAE CCS, and Chargepoint Express 20), with separate CC-CV charging modes of the DC fast chargers incorporated. To quantify the impacts, case studies are conducted on the simulation platform for two different scenarios. • The impact on the electric power grid is evaluated in terms of voltage drops, maximum power demand, current, and voltage total harmonic distortion (THD) experienced by the corresponding transformer connected to the charging stations. • The results have revealed that random and fluctuating EV fast-charging loads pose much more intense impacts on the power systems than the normal EV slow charging loads. The era of the electrified transportation system is fast approaching. Although the socioeconomic and environmental benefits of electric vehicles (EVs) have contributed to their large-scale utilization, it has also created a huge load demand on the existing power grids throughout the world. Moreover, fast, super-fast, and ultra-super-fast charging stations are under development, some of which are now in the markets. These have the potential to cause power quality issues such as charging transients, rapid voltage fluctuations, and harmonics in the power grids. Moreover, EVs can participate as mobile storage to provide vehicle-to-grid (V2G) support and ancillary services. There are still some barriers to the wide implementation of V2G systems. This paper addresses these issues and provides a review of the state-of-the-art EV technologies and their impacts on power grids. This paper also investigates the impacts of random and fluctuating EV fast-charging loads on the electric power grids, mainly considering the random connection of EVs to the power grids through DC fast-charging stations as the principal source of fluctuating EV loads. A practical electrical grid of Wollongong, New South Wales, Australia has been considered in this work to separately analyze the impacts of constant current (CC) and constant voltage (CV) charging modes upon the grid. Furthermore, design and modeling of three different commercial DC fast charger connections (CHAdeMO, SAE CCS, and ChargePoint Express 200), with separate CC-CV charging modes of the DC fast chargers have been incorporated. To quantify the impacts, two separate scenarios were examined using a simulation platform, with case studies conducted to determine the impacts on the power grid. The first scenario involved three fast charging stations, while the second scenario featured ten stations that were able to charge six and twenty electric vehicles respectively, with various load combinations considered. Each of these scenarios was analyzed under different conditions to evaluate their impact on the grid, using factors such as voltage drops, maximum power demand, current, and voltage total harmonic distortion (THD) for the transformer that was connected to the charging stations. The study results indicated that the power systems were affected more significantly by random and fluctuating EV fast-charging loads, compared to normal EV slow-charging loads. [ABSTRACT FROM AUTHOR]

Australia has significant offshore wind resources that can support ever-increasing power demand and hence provide a long-term contribution to the net-zero target by 2050. Although some offshore wind farm projects are proposed in Australia, the industry is not mature enough to justify the benefits and display economic opportunities. More specifically, the techno-economic analysis of offshore wind energy has not been systematically mapped in Australia. Therefore, the investigation of the spatial variation of technical feasibility and economic potential of offshore wind is vital to identify the potential regions and to develop strategies for future offshore wind farm developments in Australia. This paper presents detailed mappings of the techno-economic potential of offshore wind energy in Victoria-Tasmania's exclusive economic zone. Offshore wind energy resources are assessed in the paper in terms of energy availability and variability and the feasibility of various offshore wind technologies is investigated, including turbines, foundation types and transmission topologies. In addition, the high-fidelity life-cycle cost models and two innovative evaluation matrices are developed to assess the economic potential of offshore energy farms in South-eastern Australia. The impact of local power system regulation costs and future carbon prices on the viability of offshore wind is also investigated in this paper. It is concluded that the detailed mapping approach and analysis in the paper can provide a systematic tool for industry partners, investors and policymakers at the pre-planning stage of developing offshore renewable energy systems. • The technical feasibility of offshore wind is mapped under various constraints. • The novel LACE and high-fidelity LCC assessment models are developed. • The techno-economic potential is systemically mapped in South-eastern Australia. • The impacts of electricity market regulation and future carbon prices are studied. [ABSTRACT FROM AUTHOR]

More than 200,000 ha of short rotation Eucalyptus globulus plantations have been established in south-western Australia to supply wood for the pulp and paper industries. Sustaining the productivity of these tree crops over successive rotations will depend in part on maintenance of soil fertility, especially soil nitrogen (N) supply. We investigated the impact of four alternative strategies for management of harvest residues on soil N dynamics in recently logged first rotation plantations. The experiments were conducted over 5 years following harvesting at two sites with contrasting soils—a coarse textured grey sand over laterite (Podzol) with low natural fertility and a relatively fertile red earth soil (Ferralsol). At the grey sand site, 31 t ha−1 of residues containing 219 kg N ha−1 were deposited following harvest while at the red earth site the equivalent figures were 51 t ha−1 of residues and 347 kg N ha−1. Experimental treatments applied included residues burned, removed, retained and retained with double the amount of residues. The impact of treatments on soil nitrogen supply was investigated by incubating intact soil cores in the field to determine rates of net N mineralization. Additionally, the effect of treatments on soil moisture and temperature, the resident pool of soil mineral N and the amount of N potentially available for mineralization was assessed. The mulching effect of retained residues resulted in higher soil moisture where residues had been retained and a trend for soil on these treatments to dry out more slowly with the onset of the dry summer season, especially in the first year following harvest. Diurnal variations in soil temperature were moderated and average soil temperatures were reduced during summer where residues were retained. Concentrations of mineral N in soil were high in the 2 years following harvest at both sites and declined as newly established seedlings developed. At the more fertile site, where mineral N occurred predominantly as nitrate, retention of residues resulted in lower pools of soil mineral N following harvest. The effect of residue treatments on soil mineral N pools was less marked at the grey sand site. Concentrations of potentially mineralizable soil N and the amounts of N mineralized annually were greater where residues were retained at both sites. The results indicate that retention of harvest residues will favour the conservation of N following logging. However, accumulation of soil mineral N following harvesting due to reduced plant uptake will result in leaching of N early in the rotation that is largely independent of residue management. Retaining harvest residues will contribute to enhanced N supply for the next tree crop through mineralization in the long term. However, on some sites, additions of nitrogenous fertilizers will still be required to maximise the rate of tree growth. [Copyright &y& Elsevier]

This paper examines the strategies that speakers employ in response to children's crying in the remote Aboriginal community of Wadeye, in northern Australia. Drawing on spontaneous interactions amongst Murrinhpatha speaking families, we analyse instances of crying by children aged 0;6 to 8;11 years, and the ways in which they are responded to. Results indicate that adult Murrinhpatha speakers manage children's distress through a variety of verbal and non-verbal strategies, and multimodal combinations thereof. The selection of strategies directly relates to the developmental stage of the crier. Adult caregivers respond differently to the crying of infants, of children who can walk unaided but are producing little if any language, of children who can talk intelligibly, and children more advanced again who have a degree of social independence. In the particular strategies that caregivers apply, they guide children towards a developmentally appropriate self-sufficiency. Caregivers encourage autonomy in ways that reflect a child's current abilities, be it physical, linguistic, emotional, or social. By exploring responses to crying in an under-researched cultural and linguistic context, this paper offers a unique perspective on the pragmatics of managing distress and what this reveals about local constructions of personhood within the context of carer-child interaction. • Analysis examines responses to children's crying in a remote Australian Aboriginal community. • Methods utilize multimodal analysis of spontaneous crying events in early childhood. • Findings show how caregiver responses are situated in relation to local expectations of children across developmental stages. [ABSTRACT FROM AUTHOR]

This paper examines the strategies that speakers employ in response to children's crying in the remote Aboriginal community of Wadeye, in northern Australia. Drawing on spontaneous interactions amongst Murrinhpatha speaking families, we analyse instances of crying by children aged 0;6 to 8;11 years, and the ways in which they are responded to. Results indicate that adult Murrinhpatha speakers manage children's distress through a variety of verbal and non-verbal strategies, and multimodal combinations thereof. The selection of strategies directly relates to the developmental stage of the crier. Adult caregivers respond differently to the crying of infants, of children who can walk unaided but are producing little if any language, of children who can talk intelligibly, and children more advanced again who have a degree of social independence. In the particular strategies that caregivers apply, they guide children towards a developmentally appropriate self-sufficiency. Caregivers encourage autonomy in ways that reflect a child's current abilities, be it physical, linguistic, emotional, or social. By exploring responses to crying in an under-researched cultural and linguistic context, this paper offers a unique perspective on the pragmatics of managing distress and what this reveals about local constructions of personhood within the context of carer-child interaction. • Analysis examines responses to children's crying in a remote Australian Aboriginal community. • Methods utilize multimodal analysis of spontaneous crying events in early childhood. • Findings show how caregiver responses are situated in relation to local expectations of children across developmental stages. [ABSTRACT FROM AUTHOR]

This paper examines the relationship between locus of control (LOC) and the demand for supplementary health insurance (SUPP). Drawing on longitudinal data from Germany, we document robust evidence that individuals internal LOC increases the take up of supplementary private health insurance (SUPP). We find that the effect of one standard deviation increase in the measure of internal LOC on the probability of SUPP purchase is equivalent to a 14 percent increase in household income. Second, we find that the positive association between self-reported health and SUPP becomes small and insignificant when we control for LOC. These results suggest that LOC might be an unobserved individual trait that can partly explain previously documented evidence of advantageous selection into SUPP. Third, we find comparable results using data from Australia, which enhances the external validity of our results. [ABSTRACT FROM AUTHOR]

• Evaluate the effect of uncertain operating and market conditions on dispatch planning. • Apply Model Predictive Control (MPC) for dispatch scheduling of CSP plants. • Monte-Carlo simulation is to evaluate the MPC performance for a case-study in Australia. • The plant profitability from electricity sales under spot prices is assessed. The aim at dispatch scheduling for concentrating solar power plants is to utilize thermal storage to maximize profit from electricity generation. The dispatching plan, however, must contend with significant uncertainty in both weather forecasts (particularly solar irradiation) and, in some locations, real-time electricity prices governed by potentially volatile markets. This paper proposes a Model-Predictive Control (MPC) which employs a novel similarity-based forecast for weather variables and exploits the predictions of electricity prices provided by the market operator. A Monte-Carlo simulation is developed to evaluate true performance of the proposed MPC against two benchmarks, with perfect knowledge (PK) forecasts and day-ahead optimized using prototypical weather (DAPW). A case study is performed on a 115 MW Solar Tower plant with 8-hour storage, hypothetically located in South Australia, and operates under either a fixed-price or a real-time spot price scenario. A Monte-Carlo simulation is conducted for 150 tests for January (summer) and August (winter). The results show in fixed-price scenario MPC achieves 82.4 % of optimal profit (i.e. obtained via PK) in January and 72.4 % in August whereas that in DAPW falls to 71.5 % and 56.9 % of optimal, respectively. In the spot market scenario, MPC reaches 71.3 % and 63.6 % of optimal profit in January and August, whereas that for DAPW reaches 61.4 % and 55.1 %, respectively. In conclusion, PK forecast assumption in dispatch planning over-estimates the achievable profit by ∼ 28–40 % particularly in spot market scenario. Moreover, MPC can mitigate the influence of uncertainties on the plant economic performance by 8.5 %–15.5 % compared to DAPW benchmarks. [ABSTRACT FROM AUTHOR]

The major metropolitan airports in Australia have become increasingly congested, resulting in substantial increases in operational costs and waiting time at these airports. This paper assesses the effectiveness of subsidy programs in shifting airfreight from metropolitan airports to regional airports assuming the vehicle routing problem approach is used to optimise the downstream (i.e., road) logistics. We analyse the freight distribution network structure and logistics decisions under two (government) subsidy scenarios. We develop a mixed integer linear programming model incorporating the time-window and release-time constraints. A case study in Australia is used to illustrate the application of the proposed framework. The results show that introducing subsidies can effectively reduce the total costs from the prospective of industries involved in the airfreight distribution. The subsidy program under a non-linear subsidy provides a better performance from the economic and delivery time perspectives. However, if the primary goal is to reduce the volume of cargo traffic at the metropolitan airport, a linear subsidy program is preferred. • Subsidy programs are proposed to shift airfreights from metropolitan airports to regional airports. • The vehicle routing problem model is used to evaluate the effects of the subsidy schemes. • A case study of Australia is presented. • A non-linear subsidy provides a better performance from the economic and delivery time perspectives. • A linear subsidy is preferred to reduce cargo traffic at metropolitan airports. [ABSTRACT FROM AUTHOR]

This paper analyzes the relationship between interest rates, inflation expectations and inflation rates in Australia using the approach suggested by Toda and Yamamoto (1995) to test for Granger causality. The empirical evidence reported here suggests that uni-directional Granger causality is running from medium- and long-term government bond yields to short-term inflation expectations as measured by a survey among consumers. Moreover, there is bidirectional Granger causality among short-term interest rates and short-term inflation expectations among consumers. Additionally, interest rates and the sentiment data measuring inflation expectations can help to predict inflation rates. These findings are supportive for the Fisher effect and also seem to indicate that the bond market is quite efficient predicting inflation rates. Furthermore, some problems of more traditional tests of the Fisher hypothesis are discussed. In this context the role of financial deregulation in Australia is examined. Thus, the Lucas critique seems to be of some relevance testing the Fisher effect (see Lucas, 1976). [ABSTRACT FROM AUTHOR]

• Features, factors, and facets of solar pond design and construction. • El Paso Solar Pond experience as the basis for design specifications. • Design and planning ensure solar pond reliable and sustainable operation. • Purpose of solar ponds provides focus for design and configuration. Over the last four decades, salinity gradient solar pond (SGSP) science and technologies have advanced in practical projects. In this work, we show that understanding a salinity gradient solar pond's purpose provides the focus for preparing a preliminary design and physical configuration. This paper aims to share lessons learned in designing and constructing the El Paso Solar Pond. Features, factors, and facets of solar pond design and construction are presented straightforwardly to inform and guide planning for future work. Emphasis is on sodium chloride-based ponds, the base salt used for the El Paso Solar Pond. However, lessons learned are pertinent to additional salt source configurations. Reference to solar ponds operating in Australia and Israel provides design and construction insights. Careful design and planning prior to construction ensure the solar pond operates reliably and sustainably. [ABSTRACT FROM AUTHOR]

[Display omitted] • Adults produce more absorbent hygiene product (AHP) waste than infants in Australia. • In Australia, the majority of used AHPs go to landfill as municipal solid waste. • Our results recommend more sustainable management of waste from all AHPs. The environmental issues relating to disposable of infant nappies have received considerable attention. However, adult absorbent hygiene products (AHPs) receive less attention, despite having comparable or greater environmental impact. Here we quantify and compare current and future flows of continence related AHPs entering waste streams from both infant and adult populations. Importantly our study accounts for current waste management and landfilling practices across Australia and the environmental implications of AHP disposal. Absorbent hygiene product use from infants and adults was modelled from 2020 to 2030 for Australia, and it's predicted that AHP waste generated by adults will account for between 4 and 10 times that of infants by 2030 due to an aging population. Our results indicate that 50% of used AHPs end up in landfill with both leachate and biogas collection, the remainder going to landfills without biogas collection or without both leachate and biogas collection, based on the most recent national data set, which is over a decade old. The average composition of used absorbent hygiene product (including 60% urine and faeces by mass) is estimated to contain 20% non-biodegradable material, which may complicate the biodegradability of absorbent hygiene products in landfill. Without additional regulatory incentive, the current waste management practices in Australia are likely to continue, with absorbent hygiene products typically entering landfill as municipal solid waste, rather than industrial composting or recycling facilities. More accurate estimation of environmental implications from these disposal pathways requires further work including biodegradation experiments currently unavailable in the literature. [ABSTRACT FROM AUTHOR]

As research has shown, the interactional practice of getting acquainted in initial encounters can play a crucial role in the construction of interpersonal relationships. This exploratory paper focusses on one aspect of the getting acquainted discourse, i.e. how conversational openings are constructed in dyadic and multi-party interactions between previously unacquainted interlocutors. These interactions are examined in a specific context – the launch night episode of the reality television gameshow Big Brother Australia 2012. The findings indicate that, while some conversational openings follow the canonical structure, including preference for self-identification, in most conversational openings in our data, the interactants tend to request other-identification, which, importantly, is not treated as problematic. In addition, this study further confirms that introducing sequences are discursively constructed as essential in conversational openings. This becomes visible when the lack of identification at an early stage is treated as problematic by the interlocutors who orient to resuming or initiating introducing, whether prompted or unprompted, while engaging in the first instances of getting acquainted. • This paper explores how conversational openings are constructed in interaction. • This paper analyses dyadic and multi-party interactions in a reality television gameshow. • Interactants tend to request other-identification, not offer self-identification. • Introducing sequences are essential in conversational openings while getting acquainted. • Lack of self-identification is treated as problematic by interlocutors, and if missing, is resumed at a later stage. [ABSTRACT FROM AUTHOR]

There is little research to understand reasons for suboptimal influenza vaccination uptake among Aboriginal people of different ages in Australia. This study aimed to better understand the communication needs and preferences of Aboriginal families (Phase 2) in New South Wales, Australia, and their health service providers (Phase 1), to inform future interventions to improve influenza immunisation coverage in Aboriginal communities. This paper reports from Phase 1 of the study. Aboriginal and non-Aboriginal researchers designed and conducted the study, with cultural governance provided by Aboriginal health care professionals and other community members working within health departments or community healthcare settings across Australia. In Phase 1 we conducted interviews and focus groups with 18 Aboriginal immunisation providers and mainstream immunisation co-ordinators from three geographic areas in New South Wales. We used group-based thematic analysis with a cultural lens and sought participants' feedback prior to finalising results. We identified four themes, framed as opportunities for improvement: better supporting Aboriginal Medical Services as providers of influenza vaccinations; improving the accessibility and appropriateness of mainstream services for Aboriginal families; improving health providers' knowledge of Aboriginal people' influenza risk and their willingness to recommend vaccination; and engaging communities to design influenza vaccination resources. To achieve optimal influenza vaccination coverage, all health services must take responsibility for providing culturally responsive clinical care to Aboriginal families. We suggest that, where possible, mainstream services incorporate elements of the family-centred and broader model of health used by Aboriginal Medical Services. This includes creating a welcoming environment, appropriately identifying and getting to know Aboriginal patients, taking a preventative approach, and opportunistically offering and strongly encouraging influenza vaccination to the individual and their family. [ABSTRACT FROM AUTHOR]

With the urgent need to decarbonise the world's energy system, clean hydrogen is emerging as a potential technological solution. As with any new technology, understanding the public's response to hydrogen is critical to its success. Most studies examining public attitudes towards hydrogen have focused on refuelling stations and transport options. As a first of its kind, using a national survey (N = 2785) we evaluate the Australian public's response towards hydrogen for domestic and export use. In Australia, acceptance of hydrogen in domestic applications was influenced by its relative cost, ability to reduce air pollution and associated health benefits. Further, support for a hydrogen export industry was influenced by levels of trust in the government to manage the associated risks and the industry's commitment to climate protection. The paper concludes that effective, nuanced communication and engagement along with supporting financial policies will be critical in facilitating societal acceptance of hydrogen in Australia. [Display omitted] • An Australian national survey investigating subjective support for hydrogen. • Technology Acceptance Framework variables strongly influence hydrogen support. • The influence of TAF variables is observed in domestic use and hydrogen export. • One third of participants support a hydrogen plant being built near them. • Behavioural factors did not have a significant influence on hydrogen support. [ABSTRACT FROM AUTHOR]