Search

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

We employed a microwave-assisted two-pot in-situ deposition technique to incorporate zinc oxide particulates in the structure of filter paper to produce antimicrobial paper. The process involved successive immersion of filter paper samples in ZnSO4 (precursor solution) and NaOH (precipitating agent) to form Zn(OH)2, which transformed into ZnO during microwave treatment. Successful deposition of ZnO particles on the filter paper was confirmed via X-ray diffraction and the corresponding morphologies were observed using field emission scanning electron microscopy. The ZnO-deposited papers were tested for antimicrobial activity and were found to be more effective against Staphylococcus aureus (gram-positive) than Escherichia coli (gram-negative). Bacterial populations were reduced by up to 92 ± 2% and 57 ± 4% for S. aureus and E. coli, respectively. Also, it was found that the samples prepared using higher concentrations of ZnSO4 and NaOH exhibited better antimicrobial properties.

Cellulose based nanomaterials have the great potential to be applied to paper as bulk additive or coating material to improve overall final properties, especially in secondary fiber. In the present work, the effect of applying different kinds of cellulose nanofibrils (CNF) to papers obtained from recycled fibers using size press on physical, mechanical and barrier properties was investigated and compared with the sole use of starch as coating material. The coating process of CNF was carried out by the addition of size press grade starch to coating suspension. As a cellulose source, wheat straw was evaluated and CNF was obtained through oxidative and enzymatic pretreatments. Results indicate that starch/CNF suspension improves the overall paper properties. As a result of the deposition of coating suspension contains of 4 % wt. periodate-oxidized CNF onto paper surface, tensile and burst indices of papersheets increased as 52.2 % and 194.4 %. Significant decreases were observed in air permeability as 69.8 %. Compression tests also have been conducted to evaluate papersheets end-use properties. In comparison to the other pretreated CNF, due to is lower viscosity, applying periodate-oxidized CNF as size press significantly increased the mechanical properties of the papers fabricated from the recycled pulps. TUBITAK-TEYDEBTurkiye Bilimsel ve Teknolojik Arastirma Kurumu (TUBITAK) [1505]; Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate [1505, 5180044] This work was supported by TUBITAK-TEYDEB 1505 (The Scientific and Technological Research Council of Turkey, Technology and Innovation Funding Programs Directorate 1505), Project No. 5180044. WOS:000703585400013 2-s2.0-85108063350

Graphical abstract Enzyme-linked immunosorbent assay (ELISA) is widely used for the detection of disease biomarkers. However, it utilizes time-consuming procedures and expensive instruments, making it infeasible for point-of-care (POC) analysis especially in resource-limited settings. In this work, a multicolorimetric ELISA biosensor integrated on a paper/polymer hybrid microfluidic device was developed for rapid visual detection of disease biomarkers at point of care, without using costly equipment. This multicolormetric ELISA platform was built on multiple distinct color variants resulted from the catalytic oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB) and the etching of gold nanorods (AuNRs). The vivid color changes could be easily distinguished by the naked eye, and their red mean values allowed quantitative biomarker detection, without using any sophisticated instruments. When this multicolorimetric ELISA was integrated on a paper/polymer hybrid analytical device, it not only provided integrated processing and high portability but also enabled fast assays in about 50 min due to the unique advantages of paper/polymer hybrid devices. The limit of detection of 9.1 ng/μL of the hepatitis C virus core antigen, a biomarker for hepatitis C, was achieved using this multicolorimetric ELISA platform. This multicolor ELISA analytical device provides a new versatile, user-friendly, affordable, and portable immunosensing platform with high potential for on-site detections of various viruses, proteins, and biomarkers for low-resource settings such as at home, public venues, rural areas, and developing nations. Supplementary Information The online version contains supplementary material available at 10.1007/s00216-021-03359-8.

Funding Information: The financial support of the Austrian Federal Ministry of Digital and Economic Affairs and the National Foundation for Research, Technology and Development , Austria, is gratefully acknowledged. We also thank the industrial partners Mondi, Canon Production Printing, Kelheim Fibres, and SIG Combibloc for their support. Publisher Copyright: © 2021 Copyright: Copyright 2021 Elsevier B.V., All rights reserved. Hydrophobization of cellulosic materials and particularly paper products is a commonly used procedure to render papers more resistant to water and moisture. Here, we explore the hydrophobization of unsized paper sheets via the gas phase. We employed three different compounds, namely palmitoyl chloride (PCl), trifluoroacetic anhydride/acetic anhydride (TFAA/Ac2O)) and hexamethyldisilazane (HMDS) which were vaporized and allowed to react with the paper sheets via the gas phase. All routes yielded hydrophobic papers with static water contact angles far above 90° and indicated the formation of covalent bonds. The PCl and TFAA approach negatively impacted the mechanical and optical properties of the paper leading to a decrease in tensile strength and yellowing of the sheets. The HMDS modified papers did not exhibit any differences regarding relevant paper technological parameters (mechanical properties, optical properties, porosity) compared to the non-modified sheets. XPS studies revealed that the HMDS modified samples have a rather low silicon content, pointing at the formation of submonolayers of trimethylsilyl groups on the fiber surfaces in the paper network. This was further investigated by penetration dynamic analysis using ultrasonication, which revealed that the whole fiber network has been homogeneously modified with the silyl groups and not only the very outer surface as for the PCl and the TFAA modified papers. This procedure yields a possibility to study the influence of hydrophobicity on paper sheets and their network properties without changing structural and mechanical paper parameters.

Currently, most of the collected waste medium-density fiberboards (MDF) is incinerated or landfilled, as economically viable recycling methods are yet to be developed. By steam refining waste medium-density fiberboards (MDF), it is possible to hydrolyze the incorporated resins and isolate a high yield fiber fraction. Further refining of the steam treated fibers might enable the fibers to be utilized in applications such as paper packaging, facilitating a cascading use of the waste material stream. To this end, intimate knowledge of the material is needed. In this study, the steam refined fibers of two waste MDF samples containing differing amounts of softwood and hardwood underwent refining and beating. The resulting fibers were characterized regarding their morphology and paper test sheets were produced to evaluate their strength (compression-, tensile- and tear-strength). Distinct differences in response to refining between the MDF samples were apparent. For the sample with the higher hardwood share an increase in strength properties with increasing steam treatment severities could be observed and it was possible to produce test sheets with comparable compression strength to recycled pulp for industrial corrugated paperboard. For the sample with a higher share of softwood, the steam treatment severity did not show any influence on fiber morphology or paper properties, and the resulting paper strength was low in comparison to the other steam refined waste MDF sample. Graphic Abstract

The development of industry and of the Internet of Things (IoTs) have brought energy issues and huge challenges to the environment. The emergence of triboelectric nanogenerators (TENGs) has attracted wide attention due to their advantages, such as self-powering, lightweight, and facile fabrication. Similarly to paper and other fiber-based materials, which are biocompatible, biodegradable, environmentally friendly, and are everywhere in daily life, paper-based TENGs (P-TENGs) have shown great potential for various energy harvesting and interactive applications. Here, a detailed summary of P-TENGs with two-dimensional patterns and three-dimensional structures is reported. P-TENGs have the potential to be used in many practical applications, including self-powered sensing devices, human–machine interaction, electrochemistry, and highly efficient energy harvesting devices. This leads to a simple yet effective way for the next generation of energy devices and paper electronics.

Paper and pulp mills generate substantial quantities of cellulose-rich sludge materials that are disposed in landfills at a large scale. For sustainability purposes, sludge materials can be bioprocessed to produce renewable fuels and useful chemicals. The enzymatic hydrolysis of cellulose is the process bottleneck that affects the conversion economics directly by using zero-cost raw materials. In order to study and optimize the process, the characteristics of the sludge raw materials should be first evaluated. In this work, sludge samples were obtained from paper mills located at different locations in Wisconsin and Minnesota. Part of the sludge samples was washed (de-ashed) with hydrochloric acid while the other part remained unwashed. The samples were subjected to multiple spectroscopic analyses techniques to evaluate the morphological properties of cellulose fibers and to estimate the total structural carbohydrate content. The results showed that the de-ashing process changed some fiber characteristics and cellulose crystallinity structure in all sludge samples. Sludge sample A (obtained from Kraft pulp and recycled paper mill region) showed a high percentage of fiber, with crystalline cellulose, compared to the other two sludge samples suggesting that sludge A is a valuable source to make value-added products. Aspen Plus mass and energy calculations performed in view of the ‘zero’ cost and the reliable supply of sludge raw materials producing 2 mol H2/mol glucose. Moreover, the results showed that extracting crystalline cellulose from these sludge samples is more profitable than crystalline cellulose made from the other lignocellulosic feedstocks. The results reported here showed that the utilization of these sludge materials would be an economically attractive and promising alternative for the production of hydrogen.

The present study reports the characterization of reverse osmosis (RO) technology at water treatment plant Cogen-2 in paper and Board mills, Pakistan. RO is a commonly used process to obtain de-mineralized water for high-pressure boiler operation in thermal power plants. Scaling and fouling in three-stage RO plants is a major challenge in chemical industry due to the use of raw brackish water in the power plant of paper and board mills. In our study, the feed water quality of RO was changed from soft water to raw water to make it economical. The cleaning frequency was increased three times than normal, which was unsafe for operation and it was required to control scaling and fouling to achieve the desired result. Differential pressures behavior of all stages for 2-month data was observed without acid treatment, and the results of Langelier Saturation Index (LSI) control parameters (temperature, pH, total dissolved solids, calcium hardness, and alkalinity) clearly showed the abnormality. To optimize scaling and fouling of RO, the LSI factor was controlled in total reject water for the next 2 months by acid treatment in feed water. Duration of chemical cleaning and membranes’ life has been extended by fouling and scaling control. Understanding the effect of operational parameters in RO membranes is essential in water process engineering due to its broad applications in drinking water, sanitation, seawater, desalination process, wastewater treatment, and boiler feed water operation. The product flow increased from 18.3 to 19.9 m3/h, and this was due to a decrease in the rejection flow from 8.2 to 6.7 m3/h. The total reject stream pressure also increased from 8.1 to 9 bar. A lower value of LSI of 1.6 is obtained in the reject water stream after the acid treatment.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Introduction We developed low-cost, portable paper-based diagnostic devices for detection of human immunoglobulin M (IgM) and immunoglobulin G (IgG) in serum without any sample preparation. These devices can be used to help identify presence of diseases, used to provide rapid results ( Materials and Methods We successfully accomplished colorimetric detection of human IgG and human IgM using a sandwich-style assay within the microfluidic paper device via vertical flow immunoassay configuration. The reaction zone in the wax printed paper layer is a small circular pattern. Gold nanoparticles conjugated with anti-human IgG and IgM antibodies have been used for colorimetric detection of IgG or IgM by naked eye. Colorimetric signal can be precisely quantified through implementation of image analysis software which can be developed as an app for a smartphone. The size of the device is 2 cm × 2 cm × 1 mm. Results Colorimetric detection of human IgG was accomplished at 100 fg/mL concentration using a gold nanoparticle–conjugated anti-human IgG antibody. The developed platform has a dynamic range of IgM and IgG concentrations between 0.1 pg/mL and 100 μg/mL. These devices provided a color readout in Conclusions Because of the inherent simplicity of the device operation and their ease of use, there is no variation between samples and users of the device. This low-cost approach enables multiplexing with >1 measurement performed in parallel at the same time. We anticipate that because of the sensitivity, specificity, ease of use, and overall reliability, this approach will become a standard for diagnosis of diseases and health conditions.

The present work describes a sensitive, simple, cost-effective and fast analytical procedure to detect the parabens in industrial waste effluent water samples using novel activated carbon nanofiber (CNF) modified filter paper based solid phase extraction technique coupled with liquid chromatography with photodiode array detector (UPLC-PDA). The carbon nanofiber coated filter paper was used as an adsorbent and also characterized by field emission scanning electron microscope (FESEM) showed superior porous structure. Various factors effecting the adsorption and desorption process were studied. The optimum parameters which improve the efficiency are paper length 1 cm × 2 cm, adsorption time 15 min, eluent methanol, eluent volume 5 mL, sample pH 7, desorption time 2 min, 2% salt addition and 300 rpm stirring rate respectively. The parabens exhibited superior linearity ranging from 0.1-50 ng mL-1. The regression coefficient (R2) value ranging from 0.9981-0.9989. This method exhibited good sensitivity with the quantification limit (LOQ) between 0.5-0.75 ng mL-1 and detection limit (LOD) over the range of 0.1-0.25 ng mL-1. The precision was expressed from the RSDs values from 0.74-0.97 %. The spiked analytes revealed excellent recoveries in the range of 95.30-116.72 % with RSD less than 5.72 % for all the water samples also applied for real samples.

The paper corrugation tube is an innovative kind of energy absorbing structure and shock absorber which can play an important role on the cushioning energy absorption for airdrop equipments and transportation packaging. The deformation characteristics and failure modes of the regular triangle, quadrangle, pentagon and hexagon paper corrugation tubes were comparatively studied by a series of axial static compression experiments, the cushioning energy absorption was evaluated by the seven characteristic parameters (e.g. initial peak force, mean crush force, total energy absorption, specific energy absorption, crush force efficiency, unit area energy absorption and stroke efficiency), and the influences of tube direction, cross-sectional shape, tube length and compression rate on failure modes and cushioning energy absorption were analyzed and compared. These researches showed that the tubes along X direction only have the accordion deformation mode, yet the tubes along Y direction have four deformation modes including steady state progressive buckling, Euler buckling, angular tear and transverse shear. For the paper corrugation tubes along Y direction, the cross-sectional shape has obvious influence on the cushioning energy absorption of structures, and the specific energy absorption and unit area energy absorption of regular triangle and pentagon tubes are better than those of the tubes with regular quadrilateral and hexagonal cross-section at compression rates of 12 and 48mm/min. The tube length of 150 mm or compression rate of 72 mm/min would cause the increase of contribution proportion of non-ideal deformation mode and the decrease of cushioning properties. The paper corrugation tubes along X direction have more stable and controllable deformation mode, yet the paper corrugation tubes along Y direction have better cushioning energy absorption.

We report a simple and cost-effective paper-based and colorimetric dual-mode detection of As(iii) and Pb(ii) based on glucose-functionalized gold nanoparticles under optimized conditions. The paper-based detection of As(iii) and Pb(ii) is based on the change in the signal intensity of AuNPs/Glu fabricated on a paper substrate after the deposition of the analyte using a smartphone, followed by processing with the ImageJ software. The colorimetric method is based on the change in the color and the red shift of the localized surface plasmon resonance (LSPR) absorption band of AuNPs/Glu in the region of 200-800 nm. The red shift (Δ

In China, Xuan paper has been the paper of choice as artwork support and for conservation, for several centuries. However, little is known about its material properties, especially given the many grades of sized and unsized Xuan paper. In addition, there is a lack of information on its degradation. In this research, a selection of contemporary unsized Xuan papers was investigated, representing diverse raw materials. Seven out of twelve contemporary unsized Xuan papers were determined to be approximately neutral and contain > 2% alkaline reserve, indicating good durability. Viscometry was used to determine the degree of polymerisation (DP) as none of the samples gave significant reactions to the phloroglucinol spot test. The average DP of ten contemporary unsized Xuan papers is ~ 1700, excluding two papers that have presumably been sun-bleached, and that exhibit significantly lower DP. Using X-ray fluorescence, it can be demonstrated that Ca and Si are the dominant elements and interestingly, Ca content is directly correlated with ash content and with alkaline reserve. Accelerated degradation was performed at two sets of environmental conditions, i.e. 90 °C, 30% RH and 60 °C, 70% RH, and the established degradation rates agreed with the Collections Demography model of paper degradation meaning that degradation of Xuan papers proceeds in the same way as other types of paper. This research gives fundamental insights into contemporary unsized Xuan papers, which exhibit good stability during accelerated degradation despite the low starting DP in the context of the samples used in this study. Our findings may inform methods of Xuan paper production, selection of Xuan paper for conservation purposes, as well as preventive conservation of Xuan paper-based artefacts.

Starch and derivatives thereof have proven their usefulness in paper coating processes. Among these derivatives, cationic starch has been widely used in the paper industry as a flocculation, dispersion and ink fixing agent. In another context, nanoscale cellulosic materials have been shown to improve the strength, retention of fillers, the barrier properties of packaging paper products, and printing qualities. This review summarizes the recent studies on the general components used in paper coating, describes the conventional and alternative synthetic processes of cationic starches and nanocellulose, and deals with their current and potential applications in papermaking, focusing primarily on surface treatments. Moreover, environmental applications have been considered to expand the understanding and usefulness of these materials. Further research on modified polysaccharides is encouraged to replace, in a feasible way, petro-based components of coating formulations, and to provide paper surfaces with new properties.

Process-monitoring laboratories in the pulp and paper industry generally use a combination of wet chemical analyses and physical measurements to certify the fitness of a production pulp for a specific end-use. These laboratory tests require time and the effort of trained personnel, limiting their utility for real-time process control. Here we show that Raman probes of unrefined cellulosic pulps, well-suited to the online measurement of in-process materials, can predict the quality attributes of manufactured papers. The accuracy of prediction improves when the covariance is modelled in a reduced measurement space selected by a data-driven, feature-selection technique referred to as a Template Oriented Genetic Algorithm (TOGA). TOGA, combined with discrete wavelet transform (DWT), isolates functional-group features that correlate best with mechanical properties paper derived from refined pulp. Paper makers refine market pulps to build sheet strength using a beating process that decreases freeness as it increases fibre-fibre bonding. Methods demonstrated here predict manufactured sheet properties obtainable after any specified degree of refining from the Raman spectrum of an unrefined pulp. This analysis capacity will enable both vendors of market pulp and makers of sheet paper to specify in advance the amount of beating required to produce a desired product, thereby saving cost and conserving resources.

Eco-friendly and cost-effective materials and processes to manufacture functional substrates are crucial to further advance the area of printed electronics. One potential key component in the printed electronics platform is an electrically functionalized paper, produced by simply mixing common cellulosic pulp fibers with high-performance electroactive materials. Herein, an electronic paper including nanographite has been prepared using a standardized and scalable papermaking technique. No retention aid was needed to achieve a conducting nanographite loading as high as 50 wt %. The spontaneous retention that provides the integrity and stability of the nanographite paper, likely originates partially from an observed water-stable adhesion of nanographite flakes onto the fiber surfaces. The resulting paper exhibits excellent electrical characteristics, such as an in-plane conductivity of 107 S/cm and an areal capacitance of 9.2 mF/cm(2), and was explored as the back-electrode in printed electrochromic displays. Funding Agencies|Digital Cellulose Centre, a competence center set up by the Swedish Innovation Agency VINNOVA; consortium of Swedish forest industries; Wallenberg Wood Science Center (Knut and Alice Wallenberg Foundation); VINNOVA "EPIC" projectVinnova [2017-05413]; Karl-Erik Onnesjo Foundation

An industry compatible chemo-refining approach was tested for preparation of micro-nanofibrillated cellulose (MNFC) from bleached softwood pulp using sodium meta-periodate and sodium chlorite as oxidizers followed by refining in Valley beater. SEM and FTIR analyses confirmed micro-nano scale fibrillation and chemical functional group modification in laboratory prepared MNFC, respectively. The water retention value, carboxyl content and viscosity of MNFC were found comparable with imported NFC as reference (R-NFC). To evaluate MNFC as strength enhancer for paper properties, 5% MNFC addition to bleached mixed hardwood pulp showed 6% reduction in bulk with 36%, 24% and 97% increment in breaking length, burst index and double fold of the handsheets, respectively without affecting tear index and optical properties than the control. Surface properties were also improved. Pulp drainability (37°SR) after MNFC addition was found suitable for papermaking. These laboratory results confirmed the potential of MNFC as a suitable strength additive for paper quality improvement.

In this study, a microfluidic paper-based analytical device (mu PAD) was integrated with a smartphone app capable of offline (without internet access) image processing and analysis for the rapid colorimetric detection of glucose. A self-inking stamp was used to form hydrophobic channels on a piece of paper-towel due to its superior water absorption efficiency. As demonstrated, the developed sensor was employed for the colorimetric detection of glucose in artificial saliva in the linear scope of 0 - 1 mM with a calculated detection limit of 29.65 mu M. The experimental results show that the quantitative analysis of glucose with the proposed smartphone platform could be completed in less than one minute. The app developed for the smartphone platform is capable of extracting the color-changing area with an embedded image processing tool which could address the problem of color uniformity in the detection zones of mu PAD. The integrated platform has great potential to be used for non-invasive measurements of glucose in body fluids, like tears, sweat and saliva.

Photocatalytic materials have been widely used to remove dyes from printing and dyeing wastewater. However, difficulty in recycling of photocatalysts is the great concern in the real catalytic applications, which significantly raises the application cost. This study developed a low-cost catalyst by loading magnetic Ni onto filter paper (FP) via an easy going in-situ reaction. The characterization results displayed that the Ni particles were uniformly anchored onto the FP. The Ni@FP material presented a strong magnetic ability which was evidenced by a saturation magnetization (Ms) of 5.014 emu·g−1, a remanent magnetization (Mr) of 2.067 emu·g−1 and a coercivity (Hc) of 133.868 Oe. Meanwhile, the magnetic Ni@FP material displayed a recyclable advantage in photocatalytic degradation of methyl orange (MO) via an external magnetic field. There existed an optimal photocatalytic degradation rate of 93.40% within 5 min when MO concentration was 15 mg·L−1 at pH 8.0. Three cycle experiments confirmed that the Ni@FP possessed a satisfied stability and recycling ability. Moreover, the Ni@FP material presented a strong antibacterial activity which can prevent it from being contaminated by microorganisms. The versatility of the newly proposed photocatalyst in this study demonstrated its great application prospect in dyeing wastewater treatment.

Made available in DSpace on 2021-06-25T10:45:32Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-01-25 Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq) Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES) Fundação de Amparo à Pesquisa do Estado de Minas Gerais (FAPEMIG) Lactose (LAC) is a disaccharide - major sugar, present in milk and dairy products. LAC content is an important indicator of milk quality and abnormalities in food industries, as well as in human and animal health. The present study reports the development of an innovative imprinted voltammetric sensor for sensitive detection of LAC. The sensor was constructed using electropolymerized pyrrole (Py) molecularly imprinted polymer (MIP) on graphite paper electrode (PE). The MIP film was constructed through the electrosynthesis of polypyrrole (PPy) in the presence of LAC (template molecule) on PE (PPy/PE). To optimize the detection conditions, several factors affecting the PPy/PE sensor performance were assessed by multivariate methods (Plackett–Burman design and central composite design). Under optimized conditions, the proposed analytical method was applied for LAC detection in whole and LAC-free milks, where it demonstrated high sensitivity and selectivity, with two dynamic linear ranges of concentration (1.0–10 nmol L−1 and 25–125 nmol L−1) and a detection limit of 0.88 nmol L−1. The MIP sensor showed selective molecular recognition for LAC in the presence of structurally related molecules. The proposed PPy/PE sensor exhibited good stability, as well as excellent reproducibility and repeatability. Based on the results obtained, the PPy/PE is found to be highly promising for sensitive detection of LAC. Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Institute of Exact and Natural Sciences of Pontal Federal University of Uberlandia, 1600 20 St., Ituiutaba, Minas Gerais State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Analytical Chemistry Department Institute of Chemistry São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State Bioenergy Research Institute (IPBEN) São Paulo State University (UNESP), 55 Prof. Francisco Degni St., São Paulo State FAPESP: 2017/25329–6 FAPESP: 2018/12131–6 FAPESP: 2019/13818–8 CNPq: 408783/2018–4 CNPq: 443315/2014–0 CNPq: 447668/2014–5 CAPES: 88887.368610/2019–00 FAPEMIG: APQ-02078-15 FAPEMIG: APQ-02905-15

Silver nanoparticle (AgNP)-decorated cellulose filter paper (FP), a low-cost point-of-use (POU) water disinfection system, can supply affordable and safe drinking water for people in desperate need, especially in rural areas in developing countries. However, owing to the unstable immobilization of AgNPs, silver can leach into the treated drinking water from the FP and exceed the World Health Organization (WHO) drinking water limit (

Lightweight yet strong paper with high toughness is desirable especially for impact protection. Herein we demonstrated electrically conductive and mechanically robust paper (AP/PB-GP) made of reduced graphene oxide via interfacial crosslinking with 1-aminopyrene (AP) and 1-pyrenebutyrat (PB) small molecules. The AP/PB-GP with thickness of over ten micrometer delivers a record-high toughness (∼69.67 ± 15.3 MJ m−3 in average), simultaneously with superior strength (close to 1 GPa), allowing an impressive specific penetration energy absorption (∼0.17 MJ kg−1) at high impact velocities when used for ballistic impact protection. Detailed interfacial and structural analysis reveals that the reinforcement is synergistically determined by π-π interaction and H-bonding linkage between adjacent graphene lamellae. Especially, the defective pores within the graphene platelets benefit the favorable adsorption of the pyrene-containing molecules, which imperatively maximizes the interfacial binding, facilitating deflecting crack and plastic deformation under loading. Density functional theory simulation suggests that the coupling between the polar functional groups, e.g., −COOH, at the edges of graphene platelets and −NH2 and −COOH of AP/PB are critical to the formation of hydrogen bonding network.

Neotame is an artificial sweetener with increasing consumption in recent years, excessive intake of it may bring potential health risk. In this work, a rapid method was developed to detect neotame in instant grain beverages, which was based on surface-enhanced Raman scattering (SERS) technique and filter paper-based silver nanoparticles (AgNPs@FP) substrates. The designed substrate exhibits good SERS activity with an enhancement factor of 105 because of the synergistic effect of the concentrated silver nanoparticles and filter paper. Meanwhile, the stability and repeatability of this fabricated substrate have been investigated with the relative standard deviation of 6.1%. In addition, it shows an excellent linear relationship (R 2 = 0.997) between the SERS signal and the logarithm concentration of neotame with a wide concentration range (0.05–5 g/kg) in the quantitative analysis. The limit of detection of neotame can be as low as 0.01 g/kg in instant grain beverages, which is below the maximum allowable addition level for neotame in instant grain beverages set in China (GB2760-2014, 0.16 g/kg). The proposed method has great potential for the identification and quantification of neotame in food safety applications with high sensitivity.

There is growing demand for simple to operate, sensitive, on-site quantitative assays to investigate concentrations of drug molecules in pharmaceutical preparations for quality assurance. Here, we report on the development of two colorimetric analysis methods for the study the antibiotic doxycycline hyclate (DOX) and the nasal decongestant oxymetazoline hydrochloride (OXY), in solution as well as in their respective formulations. We compare a UV/vis spectrophotometry method with a color change recorded on a microfluidic paper-based analytical device (μPAD). Detection is based on the pharmaceutical compounds coupling with diazotized 4-aminoacetophenone (DAAP) under alkaline conditions to produce colored azo-dye products. These azo-compounds were monitored by absorbance at 425 nm for DOX and 521 nm for OXY, with linear calibration graphs in the concentration range of 0.5–35 mg L−1 (DOX) and 1.0–40 mg L−1 (OXY) and limits of detection of 0.24 mg L−1 (DOX) and 0.32 mg L−1 (OXY). For the μPAD method, color intensity was measured from photographs and a linear increase was observed at concentrations from above approximately 15 mg L−1 for both compounds and up to 35 mg L−1 for DOX and 40 mg L−1 for OXY. The developed methods were also applied to the formulated pharmaceuticals and no interference was found from the excipient. Thus, the paper-based device provides an inexpensive, simple alternative approach for use outside centralized laboratories with semi-quantitative capability.

The growing need for reliable analytical tools to perform measurements at the point-of-need has prompted the development of novel sensors that are low cost, portable, sensitive, easy to use, and capable of multiplexed analysis. Miniaturization of the sensors into microfluidic platforms has become a promising approach to achieve these self-contained sensors. However, traditional microfluidics often require relatively expensive and complicated pumping mechanisms that increase the cost and limit the portability of the sensors. From a material perspective, paper is an attractive substrate for constructing point-of-need sensors because of its affordability, vast availability, and self-pumping ability, particularly when combined with electrochemical detection. In this mini-review, we discuss various strategies to achieve multiplexing or simultaneous detection of multiple analytes in electrochemical paper-based devices and provide a brief guide on selecting the detection strategy based on the electrochemical property of the analytes.

A novel nacre-like flame-retardant paper based on graphene oxide (GO), and phytic acid (PTA) is fabricated via evaporation-induced self-assembly. This facile method is time saving and low energy consuming. A facile approach is proposed to improve thermal oxidative stability of GO paper by in situ phosphorus doping during flame exposure. Then fire-alarm system is designed based on the high-temperature thermal reduction characteristic of GO. The GO paper functionalized with PTA (GO-PTA) can provide ultrasensitive, reliable and longtime fire early-warning signal. Fire alarm can be triggered at approximately 0.50 s when GO-PTA samples are attacked by fire. Phosphorus atoms are in situ doped into graphene layers during fire exposure, endowing GO-PTA paper with outstanding thermal oxidative stability, and thus alarm duration time of GO is greatly improved. The work develops advanced fire detection and early-warning sensors that provide reliable and continuous signals, which provide more available time for fire evacuation.

Paper is a common material that is promising for constructing microfluidic chips (lab-on-a-paper) for diagnostics and drug delivery for biomedical applications. In the past decade, extensive research on paper-based microfluidics has accumulated a large number of scientific publications in the fields of biomedical diagnosis, food safety, environmental health, drug screening and delivery. This review focuses on the recent progress on paper-based microfluidic technology with an emphasis on the design, optimization and application of the technology platform, in particular for medical diagnostics and drug delivery. Novel advances have concentrated on engineering paper devices for point-of-care (POC) diagnostics, which could be integrated with nucleic acid-based tests and isothermal amplification experiments, enabling rapid sample-to-answer assays for field testing. Among the isothermal amplification experiments, loop-mediated isothermal amplification (LAMP), an extremely sensitive nucleic acid test, specifically identifies ultralow concentrations of DNA/RNA from practical samples for diagnosing diseases. We thus mainly focus on the paper device-based LAMP assay for the rapid infectious disease diagnosis, foodborne pathogen analysis, veterinary diagnosis, plant diagnosis, and environmental public health evaluation. We also outlined progress on paper microfluidic devices for drug delivery. The paper concludes with a discussion on the challenges of this technology and our insights into how to advance science and technology towards the development of fully functional paper devices in diagnostics and drug delivery.

Pathogen detection is crucial for human, animal, and environmental health; crop protection; and biosafety. Current culture-based methods have long turnaround times and lack sensitivity. Nucleic acid amplification tests offer high specificity and sensitivity. However, their cost and complexity remain a significant hurdle to their applications in resource-limited settings. Thus, point-of-need molecular diagnostic platforms that can be used by minimally trained personnel are needed. The nuclease protection assay (NPA) is a nucleic acid hybridization-based technique that does not rely on amplification, can be paired with other methods to improve specificity, and has the potential to be developed into a point-of-need device. In traditional NPAs, hybridization of an anti-sense probe to the target sequence is followed by single-strand nuclease digestion. The double-stranded target-probe hybrids are protected from nuclease digestion, precipitated, and visualized using autoradiography or other methods. We have developed a paper-based nuclease protection assay (PB-NPA) that can be implemented in field settings as the detection approach requires limited equipment and technical expertise. The PB-NPA uses a lateral flow format to capture the labeled target-probe hybrids onto a nitrocellulose membrane modified with an anti-label antibody. A colorimetric enzyme-substrate pair is used for signal visualization, producing a test line. The nuclease digestion of non-target and mismatched DNA provides high specificity while signal amplification with the reporter enzyme-substrate provides high sensitivity. We have also developed an on-chip sample pretreatment step utilizing chitosan-modified paper to eliminate possible interferents from the reaction and preconcentrate nucleic acids, thereby significantly reducing the need for auxiliary equipment. Graphical abstract.

Polylactic acid fibrils (PLAf) were employed as a fiber component in papermaking. The addition of 5 wt % of PLAf to bleached kraft birch pulp increased the tensile index of the resulting 100 g/m2 paper sheets by 20 % in comparison to sheets produced without PLAf. By heat-treating the paper sheets containing 5 wt % PLAf, a 35 % higher tensile index in comparison to sheets produced without PLAf was achieved. SEM imaging showed that the heat-treatment caused the PLAf to melt, which formed a film on the fiber web. The PLAf was ultrasonicated in an attempt to make its surface more hydrophilic and anionic and thus more compatible with cellulose. Chemical additives (cationic polyacrylamide, polyethylene imine and polyethylene glycol) were added to the PLAf/cellulose pulp mixture in order to increase the binding between the ultrasonicated PLAf and cellulose. Ultrasonication caused the PLAf length to decrease and the PLAf surface charge changed by 36 %, indicating that the PLAf became significantly more anionic. Neither ultrasonication of PLAf nor the chemical additives improved the paper sheets’ stretchability. Polyethyleneimine as an additive in an amount of 1 % increased the tensile index of heat-treated sheets made with 5 wt % of PLAf by 19 %.

The study describes the preparation of pulp and nanocellulose from non-wood plant materials, as well as an improved properties of paper and cardboard for mass production. The pulps from wheat straw, kenaf and flax fibers were prepared by the environmentally friendly organosolv method—cooking in a solution of isobutanol or peracetic acid. The organosolv pulps used to prepare nanocellulose had traces of lignin and mineral substances. The process of hydrolysis of the investigated organosolv pulps was optimal when carried out under the following conditions: 43% sulfuric acid, temperature 60 °C, hydrolysis time 90 min and ultrasonic treatment 60 min. Using the methods of SEM, XRD, TEM, AFM and TGA, the structure and properties of organosolv pulps and nanocellulose were studied. The use of nanocellulose in bulk and on the surface of mass types of paper and cardboard—paper for corrugation, offset paper, recycled containerboard and cardboard for flat layers of corrugated cardboard were investigated. We established the positive effect of nanocellulose application on the physical and mechanical properties of paper and cardboard. Low consumption of nanocellulose allows production of the paper and cardboard with properties that meet the requirements to appropriate standards and replacement of synthetic reinforcing materials.

A novel all-in-one paper-based sampling concept for mass spectrometric bottom-up protein analysis is here demonstrated in a chip format integrating instant immunocapture, protein reduction, - alkylation and tryptic digestion all in-device. Conventional laboratory grade filter paper was coated with the polymer 2-hydroxyethyl methacrylate-co-2-vinyl-4,4-dimethyl azlactone (pHEMA-VDM) with a subsequent covalent immobilization of the monoclonal antibody E27 targeting the biomarker human chorionic gonadotropin (hCG). In-device protein reduction and alkylation was optimized with regards to reagent concentration and reaction pH. The sampling concept showed a high degree of performance between 10 and 1000 ng/mL (R2 > 0.99) by a five-point calibration curve sampled with hCG spiked to human serum samples and freshly collected whole blood samples, respectively. LOD (experimentally obtained at 100 pg/mL (2.64 pM/0.9 IU/L)) was demonstrated to be up to ten times lower with more than six times faster sample preparation than what has previously been reported for on-paper analysis of hCG in human serum samples.

The energy efficiency of the drying section of paper machine is determined by the technology of heat flows arrangements in it. Paper drying is the most energy-consuming stage of paper production. The thermal mode of the drying section is provided by the steam condensate system which is a part of it. Analysis of exergy increments shows that almost all elements of the drying thermal process are characterized by low exergy efficiency. The main ways for increasing the degree of thermodynamic perfection of the processes occurring in the drying section of the paper machine are identified based on the exergy analysis. It is assumed that the deep internal heat recovery of the steam-air mixture for heating the source air will increase the exergy efficiency of the heat recovery plant and reduce heat removal to the environment. The effectiveness of development and implementation of a closed cycle use of steam-air mixture in the drying section was examined. Building a closed cycle provides that the air mainly has a process duty, that is, it is a transport agent for the transfer of moisture and heat along a closed circuit. The calculations show that the exergy efficiency of the processes in the recovery unit of the drying section of the paper machine of the existing production is 28.6% against 66.29% for the proposed method.

Lithium-ion (Li-ion) batteries have been fabricated in various ways to improve flexibility. Flexibility could be enhanced via active materials, separators, electrodes, and electrolytes, which could then be integrated to form flexible electronic devices with promising electrochemical properties compared to traditional non-flexible Li-ion batteries. Recent progress towards flexible Li- ion batteries fabrication, materials, and their electrochemical properties are investigated in this review. Additionally, recent developments in electronic devices utilizing flexible batteries and their future applications are explored. Portable and wearable electronics, as the primary beneficiaries of the flexible, rechargeable, and high-performance Li-ion batteries, are examined. In the end, various applications and challenges of flexible batteries in healthcare and various energy storage systems, considering practical implementation, are argued.

In order to improve the efficiency of disease diagnosis and environmental monitoring, it is desirable to detect the concentration of proteins and metal ions simultaneously, since the current popular diagnostic platform can only detect proteins or metal ions independently. In this work, we developed a colorimetric microfluidic paper-based analytical device (µPAD) for simultaneous determination of protein (bovine serum albumin, BSA) and metal ions [Fe(III) and Ni(II)]. The µPAD consisted of one central zone, ten reaction zones and ten detection zones in one device, in which reaction solutions were effectively optimized for different types of chromogenic reactions. Fe(III), Ni(II) and BSA can be easily identified by the colored products, and their concentrations are in good accordance with color depth based on the established standard curves. The detection limits are 0.1 mM for Fe(III), 0.5 mM for Ni(II) and 1µM for BSA, respectively. Best of all, we demonstrated the efficiency of the µPAD with accurate detection of Fe(III), Ni (II) and BSA from river water samples within 15 minutes. The µPAD detection is efficient, instrument-free, and easy-to-use, holding great potential for simultaneous detection of cross type analytes in numerous diagnostic fields.

Propofol is a widely used intravenous anesthetic agent in sedation and general anesthesia. To improve the safety and maintain the depth of anesthesia, it is important to develop a rapid, sensitive, and reliable method to monitor the concentration of propofol in blood during anesthesia continuously. Here, we present a novel strategy based on paper spray ionization-mass spectrometry (PSI-MS) to detect propofol. Samples (in 10 μL) were mixed with methanol as protein precipitation solvent and 2,6-dimethylphenol as internal standard. Protein micro-precipitation was achieved with methanol by vortexing and centrifuging for 5 s each, and propofol was extracted to the supernatant. PSI-MS was performed in negative ionization mode, and MS signal lasted for 1 min. The analysis of a single sample was completed within 2 min. The area ratios of propofol to internal standard were calculated for quantification. Limit of detection of 5.5 ng mL−1 and limit of quantification of 18.2 ng mL−1 were achieved for propofol in whole blood. Calibration curve was linear in the range of 0.02–10 μg mL−1. The developed method was used successfully in monitoring the propofol concentration in 3 patients’ whole blood during anesthesia, showing its further application in controlling and feeding-back target concentration infusion.

Microfluidic paper-based analytical devices (μ-PADs) fabricated in Japan were employed for the determination of total chromium (Cr) in water, soil, and lettuce irrigated with wastewater in Ethiopia. The μ-PADs, which were printed by wax printing in Japan, were transported to Ethiopia and prepared for the determination of total Cr by adding appropriate reagents to the pretreatment and detection zones. Soil and lettuce samples were determined by the μ-PADs and a UV-Vis spectrophotometer in Ethiopia. A paired t-test showed that the mean total Cr concentrations determined in the soil and lettuce samples were not significantly different between μ-PADs and UV-Vis spectrophotometric analysis at the 5% level of significance. This implies that the μ-PADs have good accuracy and reliability, and could be employed to monitor Cr in environmental samples. We found that the total Cr concentrations in all soil and lettuce samples were above the permissible limit. Moreover, evaluating Cr contamination level using the geo-accumulation index indicated that the soils were contaminated with Cr moderately to heavily. Thus, the present work successfully demonstrated the potential of remote investigations of pollution in a less-equipped laboratory by transporting the μ-PADs fabricated in another laboratory.

The sensitive quantitative analysis of trace heavy metallic elements (Cd, Mn, Cr, and Cu) in aqueous solutions was achieved successfully through the combination of filter paper enrichment with laser-induced breakdown spectroscopy. Filter paper was enriched with 0.4 mL aqueous solutions to form a homogeneous sample layer on the surface of the metallic target. Considering the limits of detection, the values deduced with calibration curves already exhibited the high performance of the proposed method at several hundred or 10 μg/L (Cd 0.165, Mn 0.035, Cr 0.012, and Cu 0.078 mg/L), lower than or comparable to those using other similar methods. The LIBS results agreed reasonably well with those from ICP-MS for real samples. All results showed that our method was suitable and accurate for rapid on-site detection of trace metals in aqueous solutions. This indicates that filter paper enrichment combined with laser-induced breakdown spectroscopy is a feasible approach to wastewater quality monitoring.

Simultaneous enhancement in water flux and removal efficiency during the filtration process remains a big challenge for separation membranes. The porous structure of the filter paper can provide many channels for water transportation, but the separation performance is generally poor. The purpose of this study is to develop a new kind of filter paper consisting of ultralong hydroxyapatite (HAP) nanowires, cellulose fibers (CFs) and double metal oxide (LDO) nanosheets, and to achieve the simultaneous enhancement of both water flux and removal efficiency for high-performance dye separation. In this work, a novel kind of LDO/HAP/CF nanocomposite filter paper consisting of ultralong HAP nanowires and CFs and LDO nanosheets has been developed for rapid water filtration and highly efficient dye adsorption. Positively charged LDO nanosheets can adsorb on the surface of negatively charged ultralong HAP nanowires and embed in the porous networked structure of the LDO/HAP/CF nanocomposite filter paper, which can provide a porous structure for rapid water transportation and can adjust the pore size of the nanocomposite filter paper. As a result, the pure water flux of the LDO/HAP/CF nanocomposite filter paper can be adjusted. The optimized pure water flux of the LDO/HAP/CF nanocomposite filter paper can reach 783.6 L m-2 h-1 bar-1, which is 1.51 times that of the HAP/CF filter paper without LDO nanosheets (518.6 L m-2 h-1 bar-1). More importantly, the adsorption capacity of LDO nanosheets is high for dye molecules, the rejection percentage of Congo red (CR) by the as-prepared HAP/CF filter paper is only 59.8%, and its water flux is 534.7 L m-2 h-1 bar-1. The optimized rejection percentage and water flux of the LDO/HAP/CF nanocomposite filter paper for CR are significantly enhanced (98.3% and 736.8 L m-2 h-1 bar-1, respectively) compared to those of the HAP/CF filter paper. The size of LDO nanosheets has a significant effect on the water flux and dye rejection percentage of the LDO/HAP/CF nanocomposite filter paper. The as-prepared LDO/HAP/CF nanocomposite filter paper is promising for the applications in highly efficient purification of wastewater containing dye molecules.

Abstract Tissue paper softness relies on two major factors, the bulk softness, which can be indicated by the elasticity of the sheet, and surface softness. Measurement of surface softness is complicated and often requires a multi-step process. A key parameter defining surface softness is the topography of the surface, particularly the crepe structure and its periodicity. Herein, we present a novel approach to measure and quantify the tissue paper surface crepe structure and periodicity based on the detection of waviness along the sample using laser scanning confocal microscopy (LSM) and X-ray tomography (XRT). In addition, field emission scanning electron microscope (FESEM) was used to characterize the tissue paper surface. We demonstrate that surface topography is directly correlated to the erosion of the doctor blade, which is used to remove the dry tissue paper from the Yankee cylinder. Because of its accuracy and simplicity, the laser confocal microscopy method has the potential to be used directly on the production line to monitor the production process of the tissue paper. XRT revealed more structural details of the tissue paper structure in 3D, and it allowed for the reconstruction of the surface and the internal structure of the tissue paper. Graphic abstract

A superhydrophobic paper with excellent robustness was fabricated by roll coating with modified nano-TiO2. First, nano-TiO2 particles were hydrophobically modified by γ-aminopropyltriethoxysilane and 1H, 1H, 2H, 2H-perfluorooctyltriethoxysilane (POTS). Then the paper coating composed of modified nano-TiO2 particles as pigments and epoxy resin (EP) as adhesives was coated on a paper surface to create the desired surface morphology and surface energy. Compared with the uncoated filter paper, the prepared paper showed an improved rough surface morphology owing to the uniform layer of TiO2 microclusters deposited on the fiber network. The superhydrophobic paper exhibited water contact angles (WCA) about 153° ± 1.5°, and water sliding angles (WSA) about 3.5° ± 0.5°, low surface adhesion and excellent bounce ability. The superhydrophobic paper can withstand a variety of wear and tear, such as tape stripping and knife scraping. The as-prepared superhydrophobic paper showed mechanical durability even after 20 wear cycles with sandpaper,thus sustaining excellent superhydrophobicity on the filter paper surface. Moreover, it remains fully functional even in environments with high concentrations of acid and alkali for 96 h. The superhydrophobicity was not affected after storage for 6 months in a natural environment. It was confirmed that the superhydrophobic paper surface exhibited excellent chemical stability, long-term stability and self-cleaning properties. The entire production process was operated under normal environment, without complex equipment; and, as such, has the possibility for large-scale production and application in industry.

This study focuses on the production and characterization of biodegradable handmade paper from the Sida rhombifolia plant (SRP) cellulose. Sida rhombifolia plant is a seasonal plant that grows in the equatorial and tropical climates. The studies carried out on this SRP were aimed at investigating the methods required for the production of handmade paper from SRP plant and also at determining the tensile strength. Four specimens of SRP paper of different additive labels S0 (no additive), S1 (starch and KOH), S2 (starch), and S3 (Foska liquid glue) were produced using the Kraft method. Tensile properties (stress at break, elongation at break, and Young’s modulus), the rate of water absorption, and the rate of moisture absorption were carried out. Results showed that the addition of potassium hydroxide considerably reduces Young’s modulus of SRP handmade paper (S1) while the Foska liquid glue (S3) significantly improves it. In addition, the addition of potassium hydroxide and Foska liquid substantially improves the water absorption properties of the paper S2 and S3, respectively. The adhesive liquid creates more porosity and consequently increases the absorption of water. The addition of potassium hydroxide and Foska liquid significantly embedded the rate of moisture absorption. From the results obtained, it can be concluded that the paper S3 can be used as packaging paper since it has better mechanical properties and moisture absorption.

We present a high resolution, ultra-frugal printing of paper microfluidic devices using in-house paraffin formulation on a simple filter paper. The patterns printed using an office inkjet printer formed a selective hydrophobic barrier of 4 ± 1 µm thickness with a hydrophilic channel width of 275 µm. These printed patterns effectively confine common aqueous solutions and solvents, which was verified by solvent compatibility studies. SEM analysis reveals that the solvent confinement is due to pore blockage in the filter paper. The fabricated paper-based device was validated for qualitative assessment of Candida albicans (pathogenic fungi) by using a combination of L-proline β-naphthylamide as the substrate and cinnamaldehyde as an indicator. Our studies reveal that the pathogenic fungi can be detected within 10 min with the limit of detection (LOD) of 0.86 × 106 cfu/mL. Owing to its simplicity, this facile method shows high potential and can be scaled up for developing robust paper-based devices for biomarker detection in resource-limited settings. Graphic abstract

In this study, development of nanocoated paper and film to increase the shelf life of food has been demonstrated. Iron oxide (Fe2O3) nanoparticles were synthesized by neem leaves extract and characterized by UV-visible spectrophotometer, exhibited an absorption peak at 326 nm. Transmission electron microscope (TEM) showed the nanoparticles ranges between 5 nm to 50 nm and selected area electron diffraction (SAED) analysis revealed the amorphous in nature of nanoparticles. The biomolecules involved in the reduction of Fe2O3 nanoparticles were confirmed by Fourier transform infrared (FTIR) spectrum. The characterized nanoparticles were coated on cellulose paper, which was characterized by Scanning electron microscope (SEM). Coated paper was wrapped with fruit, and vegetables. Similarly, fruit and vegetables were also dipped in nanoparticle-incorporated sodium alginate solution. As a result, protein estimation and water loss were estimated on regular basis to determine the shelf-life of fruit and vegetables. The shelf-life of fruit and vegetables increases while evaluated with control and uncoated on weight loss and soluble protein content. Hence, the nanomaterial-coated paper and sodium alginate film prove its potential application as food packaging materials for longer shelf-life of food.

In this work, the feasibility of producing low-cost, recyclable and biodegradable binderless all-cellulose fibreboards was demonstrated through the successful manufacturing of self-binding composites based on recycled paper and kraft fibres. These all-cellulose composites were made by a simple and environmentally friendly solvent-free mechanical fibrillation method using water as a processing aid. Kraft fibres and recycled paper pulp were mixed in a 30/70 w/w ratio and refined simultaneously in a Valley beater for different periods of time. The mechanical properties of the composites, consisting of a ‘matrix’ of recycled paper reinforced with kraft fibres, were highly dependent on the level of fibrillation of the kraft fibres. Optimal levels of fibrillation resulted in a good balance of self-binding properties and reinforcing efficiency. The hot-pressed all-cellulose panels exhibited a flexural strength of 75 MPa and a modulus of 5·9 GPa, which are impressive values compared with those of conventional fibreboard materials. In addition, these panels showed better water resistance than some existing wood panel products. These binder-free all-cellulose composites have potential as cost-effective sustainable alternatives to existing panel board products, as they are entirely made from renewable and recycled materials, which at the end of life can potentially be recycled or composted, making them perfectly fit for a circular economy.

The use of nanocelluloses is being conducted for the most diverse applications. Their performance as coating agent has been mainly explored to improve barrier properties, as they emerge as perfect candidate for plastic substitution, but it is also important to explore their potential to improve printing quality. In the present work, the influence of different nanocelluloses, obtained through mechanical, enzymatic, TEMPO-mediated oxidation and carboxymethylation treatments, in the coating process and inkjet printability of office papers was assessed. The results revealed that the cellulose nanofibrils are better for printability than the microfibrils. But the size and charge of the former must be taken into account, since fibrils of very small size penetrate the paper structure, dragging the pigments from the surface, and very anionic nanofibrils can also have negative influence on the optical density. Besides, an interesting synergy between surface-sizing starch and the cellulose nanofibrils was found to occur as the latter closed the paper structure, which prevented starch from penetrating, while potentiating both of their positive effects on ink pigment entrapment. An additional study of characterization of inkjet pigments was also performed.

Three surveys on the occurrence of foxing stains were carried out on papers dating from 1560 to 1975 in three Portuguese collections. Foxed papers were found to be more intensely and intrusively stained in certain time periods of each collection. Based on historical data and the professional paper conservation expertise, the authors linked the increased occurrence of foxing stains in certain time periods to the new papermaking processes and materials, which began to be introduced in the late 18th century, and in particular to a synergistic effect between three factors: the use of deficient gelatine sizing which began to present a poorer quality and homogeneity, the presence of iron-containing impurities throughout the paper leaf and a distinct absorbency of moisture. Observing batches of morphologically similar papers by using photographic imaging with different types of light sources and incidences, the authors verified that similar papers present similar foxing stains. Received: 2019-7-20Revised: 2019-11-19Accepted: 2019-11-27Online: 2020-5-4Publication: 2020-11-27, Foram efetuados levantamentos sobre a ocorrência de manchas de foxing em papéis de 1560 a 1975 em três acervos nacionais. Observou-se, em cada um dos espólios, que certos períodos de tempo apresentavam um surgimento mais intenso e intrusivo dessas manchas. Com base em informação histórica e na experiência profissional na área da conservação de papel, os autores relacionaram este facto com novas tecnologias e materiais usados no processo de produção de papel a partir do último quartel do século XVIII e, particularmente, com a possibilidade de existência de um efeito sinergético entre a diminuição de qualidade ou falha de uniformização da encolagem de gelatina, a presença de novos procedimentos ou aditivos ricos em impurezas contendo iões ferro e uma sorbência irregular de humidade na folha. Também verificaram, através de imagens fotográficas com diferentes incidências e tipos de radiação, que grupos de papéis morfologicamente semelhantes apresentam manchas de foxing também semelhantes. Recebido: 2019-7-20Revisto: 2019-11-19Aceite: 2019-11-27Online: 2020-5-4Publicação: 2020-11-27

Filter paper, as a widely used and low-cost lab consumable, can serve as template for the synthesis of one-dimensional (1D) materials since it is composed of 1D cellulosic fiber. In this work, 1D NiO/NiCo2O4 composite was simply fabricated by adsorption of Ni and Co acetate on the filter paper and subsequent calcination process. The precursors were obtained without further treatment to filter paper or chemical reaction between metal salts. Calcination process leads to the removal of template and formation of binary NiO/NiCo2O4 composite. Electromagnetic (EM) wave absorption performance of NiO/NiCo2O4 composite could be tuned by adjusting the calcination temperatures and dosage of metal salts. For the optimized absorber (calcination temperature of 600 °C and dosage of Ni and Co acetate with 2 mmol and 4 mmol), a wide absorption bandwidth of 6.08 GHz could be achieved with thickness of 1.88 mm and minimum reflection loss value was up to −57.4 dB by changing the thickness. The facile synthetic route may also inspire the preparation of other high-performance one-dimensional EM wave absorbing materials.