Search

This study introduces an applicable colorimetric sensor array for the detection of pesticides in the vapor phase. The array consisted of six metal nanoparticles spotted on the piece of filter paper. 3D-origami pattern was used for the fabrication of a paper-based sensor to decrease the effect of the nanoparticles leaching after exposure to analytes. Exposure to pesticide aerosols caused changes in the color of the array due to the aggregation of nanoparticles. These changes provided selective responses to thion pesticides such as malathion, parathion, chlorpyrifos, and diazinon. The sensing assay could also differentiate between aliphatic and aromatic thions and discriminate amine-containing compounds from the other studied analytes. These finding results are clearly confirmed by both visual detection and multivariate statistical methods. The proposed sensor was successfully developed for the quantitative measurement of pesticide aerosols at a very low concentration. The limit of detection of this method determined for malathion, parathion, chlorpyrifos and diazinon were 58.0, 103.0, 81.0 and 117.0, respectively. Moreover, the array could be employed to simultaneously analyze four studied pesticides. The statistcal results confirmed that the method has high performance for concurrent detection of thions as a major air pollutant without the interference of other species.

Low energy surface coatings have found wide range of applications for generating hydrophobic and superhydrophobic surfaces. Most of the studies have been related to use of a single coating material over a single substrate or using a single technique. The degree of hydrophobicity is highly dependent on fabrication processes as well as materials being coated and as such warrants a high-level study using experimental optimization leading to the evaluation of the parametric behavior of coatings and their application techniques. Also, a single platform or system which can predict the required set of parameters for generating hydrophobic surface of required nature for given substrate is of requirement. This work applies the powerful machine learning algorithms (Levenberg Marquardt using Gauss Newton and Gradient methods) to evaluate the various processes affecting the anti-wetting behavior of coated printable paper substrates with the capability to predict the most optimized method of coating and materials that may lead to a desirable surface contact angle. The major application techniques used for this study pertain to dip coating, spray coating, spin coating and inkjet printing and silane and sol–gel base coating materials.

We present a simple all-in-one paper-based sensor for E. coli detection using a composite ink made of a fluorogenic DNAzyme probe for bacterial recognition and signal generation, lysozyme that lyses whole bacterial cells, and pullulan/trehalose sugars that stabilize printed bioactive molecules. The paper sensor is capable of producing a fluorescence signal as a readout within 5 minutes upon contacting E. coli, can achieve a limit of detection of 100 cells/mL, in a variety of sample matrixes, without sample enrichment, and remains stable for at least 6 months when stored at ambient temperature. Therefore, this simple paper sensor provides rapid bacterial testing on site, and can be shipped and stored under ambient conditions to benefit users living in resource-limited regions.

Paper-based micro analytical devices offer significant advantages compared to the conventional microfluidic chips including cost-effectiveness, ease of fabrication, and ease of use while preserving critical features including strong capillary action and biological compatibility. In this work, we demonstrate an inexpensive, rapid method for high-throughput fabrication of paper-based microfluidics by patterning hydrophobic barriers using a desktop pen plotter integrated with a custom-made, low-cost paper feeder. We tested various types of commercial permanent markers and compared their water-resistant capabilities for creating hydrophobic barriers. Additionally, we studied the performance of markers with different types of paper, plotting speeds, and pattern dimensions. To verify the effectiveness of the presented fabrication method, colorimetric analysis was performed on the results of a glucose assay.

Paper spray ionization (PSI) mass spectrometry (MS) is an emerging tool for ambient reaction monitoring via microdroplet reaction acceleration. PSI-MS was used to accelerate and monitor the time course of the reaction of dansyl chloride with aniline, in acetonitrile, to produce dansyl aniline. Three distinct PSI arrangements were explored in this study representing alternative approaches for sample loading and interaction; conventional single tip as well as two novel setups, a dual-tip and a co-axial arrangement were designed so as to limit any on-paper interaction between reagents. The effect on product abundance was investigated using these different paper configurations as it relates to the time course and distance of microdroplet travel. It was observed that product yield increases at a given distance and then decreases thereafter for all PSI configurations. The fluorescent property of the product (dansyl aniline) was used to visually inspect the reaction progress on the paper substrate during the spraying process. Amongst the variety of sample loading methods the novel dual-tip arrangement showed an increased product yield and microdroplet density, whilst avoiding any on-paper interaction between the reagents.

Graphite pencil stroked electrodes for paper-based Microfluidic devices are gaining immense attention due to their electrochemical properties, cost efficiency, and ease-of-use. However, their widespread use has been hindered by the challenges associated with their manual fabrication such as non-uniformity in graphite deposition, applied pressure, etc. This work presents the design and development of an automated graphite pencil stroking device for graphite electrode fabrication with high efficiency through a compact, inexpensive and automatic process, with reduced fabrication time and human intervention leading to more uniformity. The motion platform of Graphtec plotter was used to create multiple strokes with the help of the proposed device. Such inexpensive graphite electrodes (less than the US $1) have been observed to be porous in nature, acting as diffusion agents. The automated graphite electrodes were used to study the performance of microfluidic paper fuel cells (MPFCs) with formic acid, oxygen, and sulphuric acid acting as fuel, oxidising agent and electrolyte respectively. From this configuration, the maximum current density and power density were measured to be 1,305.5 µA cm−2 and 135.5 µW cm−2, respectively at 0.3 V stable OCP at 100 strokes. Overall, the study enumerates the development of an automated pencil stroke device for fabricating graphite electrodes, which can potentially be harnessed in numerous miniaturized paper based applications.

We present a prototype for conducting rapid, inexpensive and point-of-care-compatible nucleic acid amplification tests (NAATs) for tuberculosis (TB). The fluorescent isothermal paper-and-plastic NAAT (FLIPP-NAAT) uses paper-based loop mediated isothermal amplification (LAMP) for DNA detection. The cost of materials required to build a 12-test-zone device is $0.88 and the cost of reagents per reaction is $0.43. An inexpensive imaging platform enables filter-free fluorescence detection of amplified DNA using a cell-phone camera. FLIPP-NAAT can be operated by an untrained user and only requires a regular laboratory incubator as ancillary equipment. All reagents can be dry-stored in the device, facilitating storage and transportation without cold chains. The device design is modular and the assay demonstrated high specificity to Mycobacterium tuberculosis (Mtb), analytical sensitivity of the order of 10 copies of Mtb gDNA, and tolerance to complex samples. The clinical sensitivity and specificity of sputum-based FLIPP NAAT tests were 100% (zero false negatives) and 68.75% (five false positives), respectively (N = 30), using Xpert MTB/RIF assay as the reference standard. FLIPP-NAAT has the potential to provide affordable and accessible molecular diagnostics for TB in low- and middle-income countries, when used in conjunction with an appropriate sample preparation technique. Although demonstrated for the detection of TB, FLIPP-NAAT is a platform technology for amplification of any nucleic acid sequence.

Development of cost-effective and environmentally friendly manufacturing methods will enable important advances for the production of large-scale flexible electronics. Laser processing has shown to be a promising candidate that offers a fast and non-destructive way to produce highly conductive patterns on flexible substrates such as plastics. However, an emerging option with a lower environmental impact is instead the use of cellulose-based flexible substrates, such as paper. In this work we investigate the use of laser sintering of silver nanoparticle inks, which were inkjet-printed on three different types of paper. Patterns with a high conductivity could be manufactured where a special care was taken to prevent the substrates from damage by the intense laser light. We found that the best results was obtained for a photopaper, with a conductivity of 1.63 ∗ 107 S/m corresponding to nearly 26% of the bulk silver conductivity. In addition, we demonstrate laser sintering to fabricate a fully functional near field communication tag printed on a photopaper. Our results can have an important bearing for the development of cost-effective and environmentally friendly production methods for flexible electronics on a large scale.

The unusually broad physical and chemical property window of ionic liquids allows for a wide range of applications, which gives rise to the recent spring-up of ionic liquid-based functional materials. Via solvothermal copolymerization of a monomeric ionic liquid and divinylbenzene in the presence of a tissue paper in autoclave, we fabricated a flexible porous polymer/paper hybrid membrane. The surface areas of the hybrid membranes depend on the weight fraction of the copolymer impregnated inside the tissue paper. The as-prepared hybrid membrane shows controlled surface wettability in terms of ethanol wetting and ethanol removal by harsh drying condition. This unique property provides the hybrid membrane with switchable oil/water separation function, thus of practical values for real life application.

Global health organizations recommend the use of cloth face coverings to slow the spread of COVID-19. Seemingly overnight, companies whose primary business is in no way related to healthcare or personal protective equipment – from mattresses manufacturers to big box stores – transitioned into the “mask business.” One of many options on the market are antimicrobial face masks, some of which contain silver and/or copper that may leach out of these masks. We exposed ten face masks to deionized water, laundry detergent, and artificial saliva to quantify the leachable silver and copper as a result of mask washing and wearing. Leaching varied widely across brand, metal, and leaching solution, but in some cases was as high as 100% of the metals contained in the as-received mask after 1 hour of exposure. This could lead to a total adult body metal exposure of up to 900 µg/kg of silver and 75 µg/kg of copper by wearing a given mask over an 8-hour workday. While this exposure could be minimized by pre-washing the cloth masks, this would seem to eliminate any (perceived) antimicrobial properties as the metals are eliminated into wastewater and/or graywater.

Humans have dyed textiles and leather, colored food, and paint body parts using natural dyes throughout history. Natural dyes have suffered drastically due to recent socioeconomic changes and replacement with synthetic dye in the textile industry. Hence, it is urgent to study indigenous dye plants and dyeing craft in local communities to protect these resources' potential ecological, economic, and cultural values. In 11 Monpa villages of Mêdog County, South-east Tibet, China, we conducted field research to record the indigenous method of cloth dyeing using madder dye. An aqueous extract of the root of Rubia wallichiana is a traditional madder dye. In this study, we used traditional dye and ethyl alcohol extract of the residue of aqueous extract. Two fabrics were dyed with the extractions in the presence of one of the metallic mordants or biomordants. Pigment compounds from aqueous extraction of madder and ethyl alcohol extraction of recycled madder were evaluated using Phytochemical, UV–visible spectroscopy, and FTIR test. We carried out One-way ANOVA and Duncan's new multiple range method to analyze different dying approaches and conditions. The dyed fabrics were evaluated by indicators of color strength and fastness, including washing, rubbing, and perspiration. The findings revealed the potentiality of biomordants to improve the dyeing properties of madder. The dyeing properties of recycled madder were marginally better than traditional madder. The results revealed the feasibility of enhancing the dyeing property and reuse of the residue from madder dyeing. The improved dyeing and reuse of residue can improve local ecological, economic benefits, and cultural heritage while applying research findings for the subsequent commercialization of plant dyes.

The main advantages of the dried enzymes are the lower cost of storage and longer time of preservation for industrial applications. In this study, the spouted bed dryer was utilized for drying the garden radish (Raphanus sativus L.) root extract as a cost-effective source of the peroxidase enzyme. The response surface methodology (RSM) was used to evaluate the individual and interactive effects of main parameters (the inlet air temperature (T) and the ratio of air flow rate to the minimum spouting air flow rate (Q)) on the residual enzyme activity (REA). The maximum REA of 38.7% was obtained at T = 50 °C and Q = 1.4. To investigate the drying effect on the catalytic activity, the optimum reaction conditions (pH and temperature), as well as kinetic parameters, were investigated for the fresh and dried enzyme extracts (FEE and DEE). The obtained results showed that the optimum pH of DEE was decreased by 12.3% compared to FEE, while the optimum temperature of DEE compared to FEE increased by a factor of 85.7%. Moreover, kinetic parameters, thermal-stability, and shelf life of the enzyme were considerably improved after drying by the spouted bed. Overall, the results confirmed that a spouted bed reactor can be used as a promising method for drying heat-sensitive materials such as peroxidase enzyme.

Sugarcane bagasse is a significant renewable energy source for the sugar and bioethanol industries. Bagasse ash is the waste from the combustion process and is mostly disposed of as landfill. Only a small quantity of bagasse ash is utilized as pozzolan in concrete, and a considerable quantity is left unused due to its high carbon and crystallite content. Generally, bagasse ash is rich in silica (SiO2), and it is thus an alternative source for silica extraction. In this paper, a low-energy and low-chemical consumption method is proposed to obtain silica from bagasse ash using alkali extraction and acid precipitation. The physical and chemical properties of the extracted silica are described. A silica yield of 80% and moisture absorption of 73% were achieved. The silica had amorphous phases and was light gray in color owing to the presence of carbon from incomplete combustion. Bagasse silica was used as an extender filler in an expensive photochromic pigment to increase the bulk volume. It was found that a pigment-to-silica mass ratio up to 1:10 could be used for thick-layer painting. However, a ratio of up to 1:3 is recommended for thin-layer screen-printing on fabrics. The bagasse ash silica-pigment blends have very good color fastness when washing; however, frequent aggressive washing should be avoided.

To study the influence of diesel fuel blended with polyoxymethylene dimethyl ethers (PODEn), a new alternative fuel with a high oxygen content and large cetane number, on the combustion characteristics, fuel economies, and emission characteristics of heavy-duty diesel engines that meet China VI emission standards, relevant tests were conducted on a supercharged intercooled high-pressure common-rail diesel engine. The PODEn were blended with diesel fuel at three different ratios (volume fractions of 10%, 20%, and 30%). The test results showed that the PODEn could optimize the combustion process of diesel engines that met the China VI emission standards, effectively improve the thermal efficiencies of diesel engines, and reduce the emissions of hydrocarbon (HC), carbon monoxide (CO), and soot. With an increase in the PODEn blending ratio, the peak values of the in-cylinder pressure, average in-cylinder temperature, and instantaneous heat release rate gradually decreased, and each peak progressively moved forward. As the start of combustion gradually moved forward, the combustion duration was shortened by 0.7–2.8°CA, the heat release process became more concentrated, and the effective thermal efficiency was increased by up to 2.57%. The effective fuel consumption gradually increased, yet the equivalent effective fuel consumption gradually decreased, with the largest drop being as high as 4.55%. The nitrogen oxides (NOx) emission increased slightly, and the emissions of HC, CO, and soot gradually decreased. The emissions of CO and soot declined significantly under high-speed and high-load conditions, with the highest reductions reaching 66.2% and 76.3%, respectively.

Industrial development and increased energy requirements have led to high consumption of fossil fuels. Thus, environmental pollution has become a profound problem. Every year, a large amount of agro-industrial, municipal and forest residues are treated as waste, but they can be recovered and used to produce thermal and electrical energy through biological or thermochemical conversion processes. Among the main types of agro-industrial waste, soluble coffee residues represent a significant quantity all over the world. Silver skin and spent coffee grounds (SCG) are the main residues of the coffee industry. The many organic compounds contained in coffee residues suggest that their recovery and use could be very beneficial. Indeed, thanks to their composition, they can be used in the production of biodiesel, as a source of sugar, as a precursor for the creation of active carbon or as a sorbent for the removal of metals. After a careful evaluation of the possible uses of coffee grounds, the aim of this research was to show a broad characterization of coffee waste for energy purposes through physical and chemical analyses that highlight the most significant quality indexes, the interactions between them and the quantification of their importance. Results identify important tools for the qualification and quantification of the effects of coffee waste properties on energy production processes. They show that (SCG) are an excellent raw material as biomass, with excellent values in terms of calorific value and low ash content, allowing the production of 98% coffee pellets that are highly suitable for use in thermal conversion systems. Combustion tests were also carried out in an 80kWth boiler and the resulting emissions without any type of abatement filter were characterized.

The requirement of continuous and stringent growth on filtration performance, including longer life span, higher overall efficiency, lower initial pressure drop and more cost effective, has still drove filter media manufactures to research and develop. One of the possible way to achieve these challenges, was to utilize a dual-channel head-box with two sets of pulp conveying system, which can produce filter media with bulky and gradient properties. In this study, three kinds of commercial cellulose were chosen to make two layers filtration media, analyzed the effect of fiber blend on physical properties and filtration performance. By fine-tune the slurry ratio of top layer, we made one single layer and two layers composition filter media, the thickness and air permeability of composition media were higher than single layer media. According to ISO 5011, filtration performance test has been done to compare single layer media with composition media, this composition gradient profiles that provided the life span 37.0% improvement to the terminal pressure drop during dust injecting, and the dust hold capacity improved 34.7%, the main contributor of dust hold capacity was decided by top layer, however, the overall efficiency was depended on wire side layer.

Dragon fruit (Hylocereus spp.), an important tropical fruit belonging to the family Cactaceae, is rich in essential nutrients such as vitamins, minerals, complex carbohydrates, dietary fibres and antioxidants. This study aims to distinguish three dragon fruit species well adapted to Andaman and Nicobar Island through morphological (34 quantitative and 26 qualitative traits), biochemical (5 traits) and molecular (14 ISSR primers) characterization. Morphological characterization revealed that presence of considerable amount of genetic variations among them especially for fruit characters viz., colour of peel and pulp. Cladode characters such as number of spines (3–5), length of areoles (mm) as 1–4, margin ribs of cladode (convex or concave) and its waxiness (weak or strong white waxy or light waxy) could be used for identification of three Hylocereus spp. under present study. Highest co-efficient of variation (%) obtained for pulp weight (88.7), whereas, lowest in distance of anthers belowstigma (3.3). Fruit and pulp weight (g) ranged from 26.5–419.3 and 10.3–258.8 with mean value of 204.8 and 125.3, respectively. Comparatively, high phenol (71.3–161.3) and flavonoid (26.6–508.2) content observed in peels than pulp (32.5–130.0 and 45.0–258.2) of fruit indicating higher antioxidant potential. Highest total carotenoids (µg 100 g−1), β-carotene (µg 100 g−1) and xanthophyll (µg g−1) content obtained in pulp on DGF3 (33.8), DGF4 (55.9) and DGF3 (32.7), whereas, in peel on DGF2 (24.3), DGF4 (18.5) and DGF2 (24.1), respectively. DPPH-based scavenging activity (%) revealed higher scavenging activity of peels (55.6–81.2) than pulp (36.0–75.3) extracts. Comparatively, ABTS-based scavenging activity (%) was found more than DPPH-based one. Sixteen ISSR primers screened, 14 were produced 178 reproducible amplified bands. Number of amplified bands varied from 5 in UBC887 to 19 in UBC811 with an average of 12.71 bands per primer. Range of polymorphic bands and % polymorphism observed were 1–13 and 20.0–92.8, respectively. The polymorphic information content value of ISSR marker ranged from 0.42 (UBC895) to 0.91 (UBC 856). Cluster analysis distinguished three different Hylocereus species on the basis of geographic origin and pulp colour by forming separate groups and two genotypes each showed 52% (DGF1 and DGF3) and 76% (DGF2 and DGF4) genetic similarity. Key traits identified for distinguishing three different Hylocereus species were: Pulp/ peel colour of fruits, number of spines and length of areoles in cladode. Genotypes with high carotenoid and xanthophylls content (DGF4 and DGF2) identified under present study may be of industrial importance for development of nutraceutical products to meet out the vitamin-A deficiency among humans in tropical regions needed future focus.

In present study, the effects of carbon sources on compost process and quality were evaluated in the lab-scale sewage sludge (SS) composting. The composting experiments were performed for 32 days in 5 L reactors. The results showed that carbon sources could change the nitrogen conversion and improve the compost quality. Especially, the readily degradable carbon source could promote organic matter degradation, improve nitrogen conversion process and accelerate compost maturation. The addition of glucose and sucrose could increase dissolved organic carbon, CO2 emission, dehydrogenase activity, nitrification and germination index during the SS composting. That's because glucose and sucrose could be quickly used by microbes as energy and carbon source substance to increase activity of microbes and ammonia assimilation. What's more, the NH3 emission was reduced by 26.9% and 32.1% in glucose and sucrose treatments, respectively. Therefore, the addition of readily degradable carbon source could reduce NH3 emission and improve compost maturity in the SS composting.

In the present study, five lignocellulosic biomass namely, corn cobs (Zea mays), rice husks (Oryza sativa), cassava peels (Manihot esculenta), sugar cane bagasse (Saccharum officinarum), and white yam peels (Dioscorea rotundata) of two mesh sizes of 300 and 425 microns and a combination of some and all of the biomass were pretreated using combined hydrothermal and acid-based, combined hydrothermal and alkali-based and hydrothermal only processes. The raw and pretreated biomass were also characterized by Fourier transform infrared spectroscopy (FT-IR), Brunauer–Emmett–Teller (BET), X-Ray diffraction (XRD), and Scanning electron microscopy (SEM) to determine the effects of the various pretreatments on the biomass being studied. The cellulose values of the raw biomass range from 25.8 wt% for cassava peels biomass to 40.0 wt% for sugar cane bagasse. The values of the cellulose content increased slightly with the pretreatment, ranging from 33.2 to 43.8 wt%. The results of the analysis indicate that the hydrothermal and alkaline-based pretreatment shows more severity on the different biomass being studied as seen from the pore characteristics results of corn cobs + rice husks biomass, which also shows that the combination of feedstocks can effectively improve the properties of the biomass in the bioethanol production process. The FTIR analysis also showed that the crystalline cellulose present in all the biomass was converted to the amorphous form after the pretreatment processes. The pore characteristics for mixed corn cobs and rice husks biomass have the highest specific surface area and pore volume of 1837 m2/g and 0.5570 cc/g respectively.

Drying and storage methods are fundamental for maintaining the grain quality until processing. Therefore, the aim of this study was to evaluate the associations of the drying temperature with storage systems and conditions as a strategy for preserving the quality of maize grain postharvest on laboratory and field scales. An increase in temperature accelerated the reduction in grain moisture, but increased the deterioration. The wetting during the storage period reduced the grain quality. Hermetic and aerated storage systems maintained the chemical quality of the grains. The control with healthy and whole corn dried at 80 °C and stored in silos with natural aeration provided a satisfactory quality, equivalent to those of controlled drying and storage under airtight conditions and at low temperatures. Different conditions of drying and storage of corn on the laboratory and field scales were evaluated, which provides an appropriate management of these operations to maintain the grain quality.

Cellulose nanofibers were obtained from the Colombian fique (Furcraea bedinghausii) and Acrylic hydrogels (H) and reinforced acrylic hydrogels with fique nanofibres (HRFN) were synthesized, using the solution polymerization method. The extraction was carried out using a combined extraction method (chemical procedures and ultrasound radiation). The raw material (NAT-F), bleached fibers (B-F), hydrolyzed fibers and fibers treated with ultrasound (US-F) were characterized by infrared spectroscopy (FTIR) and thermal stability analysis; also, in order to have a comparison criterion, a commercial microcrystalline cellulose sample (CC) was analyzed, which demonstrated the extraction of fique cellulose. The surface morphology of the NAT-F and the B-F was determined by scanning electron microscopy and the average particle size of the nanofibers was made through transmission electron microscopy. In H y HRFN the strain percent and compression resistance (Rc) were measured. The fique nanofibers showed diameter and length averages of 25.2 ± 6.2 nm and 483.8 ± 283.2 nm respectively. Maximum degradation temperature was 317 °C. HRFN presented higher compression resistance (16.39 ± 4.30 kPa) and this resistance was 2.5 greater than the resistance of H (6.49 ± 2.48 kPa). The results indicate that fique lignocellulosic matrix has potential application for obtaining polymeric type composite materials.

Microbial fuel cell (MFC) technology is a simple way to accelerate the treatment of the oily sludge which is a major problem affecting the quality of oil fields and surrounding environment while generating electricity. To investigate the oil removal and the characteristics of changes in the composition of bacteria, sediment microbial fuel cells (SMFCs) supplemented with oily sludge was constructed. The results showed that the degradation efficiency of total petroleum hydrocarbon (TPH) of SMFC treatment was 10.1 times higher than the common anaerobic degradation. In addition, the degradation rate of n-alkanes followed the order of high carbon number > low carbon number > medium carbon number. The odd–even alkane predominance (OEP) increased, indicating that a high contribution of even alkanes whose degradation predominates. The OUT number, Shannon index, AEC index, and Chao1 index of the sludge treated with SMFC (YN2) are greater than those of the original sludge (YN1), showing that the microbial diversity of sludge increased after SMFC treatment. After SMFC treatment the relative abundance of Chloroflexi, Bacteroidia and Pseudomonadales which are essential for the degradation of the organic matter and electricity production increased significantly in YN2. These results will play a crucial role in improving the performance of oily sludge MFC.

Lipids in sewage sludge are considered to be high-class raw materials for biodiesel or other valuable products. We profiled the characteristics and assessed the reutilization potential of lipids from different sludge sources, including sludge from the primary sedimentation tank (PST sludge) and sludge from the secondary sedimentation tank in a conventional activated sludge system (CAS sludge), as well as sludge from ultrashort-sludge retention time (SRT) activated sludge systems with different SRTs (USAS sludge, with SRTs of 0.5, 1.0, 2.0, 3.0 and 4.0 d). The results showed that the lipids in the sludges were mainly composed of cellular lipids, free fatty acids (FFAs), wax and gum. The highest lipid content was found in the PST sludge (156.8 ± 11.9 mg/g, dry basis), followed by the USAS sludges (67.9 ± 11.0–132.2 ± 11.8 mg/g) and the CAS sludge (46.0 ± 16.5 mg/g). Lipid species such as Cer, So, PE, PC, and TG were abundant, comprising over 80% of the cellular lipids in the sludges. With higher lipid contents, the PST sludge and USAS sludge (0.5 d SRT) were suggested to have a higher reutilization potential for use in producing biodiesel. In addition, the CAS sludge was promising for resource reutilization and energy recovery due to the large amount of excess sludge.

A biochemical system was used for electricity generation from food waste (FW) and spent animal beddings (SAB). The wastes were blended and fermented anaerobically to produce fermentation liquids used as fuels for running a catalytic fuel cell. The fermentation liquids were analyzed for their components. The results show the organic contents i.e. volatile solids of both FW and SAB to be 23.4 and 20.9 g/L while the carbon contents were 6.5 and 6.1 g/L respectively. The media were however very rich in volatile fatty acids (VFAs). When used, the fermentation liquids from FW and SAB generated mean open-circuit voltages of 0.64 and 0.53 V and mean maximum power densities (Pmean) of 1.6 and 1.3 mW/cm2 respectively. The fuel cell showed very high efficiency in the conversion of all VFAs especially butyric acid with the highest been 97% for FW and 96% for SAB.

The management of large amounts of eggshell waste annually produced in the world is problematic as generally this material is only disposed at landfills with odor production and microbial growth. On the contrary, significant environmental and economic advantages could be obtained transforming this biowaste into new value-added products. Eggshell biowaste was the starting material for the synthesis of hydroxyapatite by a simple and sustainable procedure and applied for the removal of Co2+ from aqueous solutions. The effects of contact time and initial metal concentration were investigated in batch experiments. Eggshell-based hydroxyapatite (ESHAP) before and after Co2+ removal was characterized by X-ray diffraction and scanning electron microscopy. The process was rapid and reached equilibrium within 80 min. The removal efficiency was in the range 70–80% which is generally higher than other waste-derived adsorbents. Adsorption of Co2+ on the surface of ESHAP particles and ion exchange with Ca2+ resulting in the formation of a Co-phosphate are the main mechanisms of the metal removal. The conversion of eggshell waste to a low-cost adsorbent for the treatment of metal contaminated waters could contribute to a more sustainable and effective management of this biowaste.

Wood chips or particles as well as shredded straw offer desired thermal insulation qualities. When exposed to a humid environment, however, fungal growth on wood and straw is an important consideration. An experimental investigation was conducted in order to evaluate the effectiveness of a simple treatment in mitigating fungal growth on wood- and straw-based insulation. This treatment involved blending of wood chips or particles, or shredded straw with an aerated slurry which offers the potential to mitigate fungal growth on biomass by a combination of physical and chemical effects without imposing a weight penalty. Experimental results verified the effectiveness of this treatment in controlling fungal growth on wood and straw subjected to different moisture conditions.

The biosorption capacities of dried meal and a waste product from the processing for biostimulant extract of Ascophyllum nodosum were evaluated as candidates for low-cost, effective biomaterials for the recovery of indium(III). The use of indium has significantly grown in the last decade, because of its utilization in hi-tech. Two formats were evaluated as biosorbents: waste-biomass, a residue derived from the alkaline extraction of a commercial, biostimulant product, and natural-biomass which was harvested, dried and milled as a commercial, “kelp meal” product. Two systems have been evaluated: ideal system with indium only, and double metal-system with indium and iron, where two different levels of iron were investigated. For both systems, the indium biosorption by the brown algal biomass was found to be pH-dependent, with an optimum at pH3. In the ideal system, indium adsorption was higher (maximum adsorptions of 48 mg/g for the processed, waste biomass and 63 mg/g for the natural biomass), than in the double metal-system where the maximum adsorption was with iron at 0.07 g/L. Good values of indium adsorption were demonstrated in both the ideal and double systems: there was competition between the iron and indium ions for the binding sites available in the A. nodosum-derived materials. Data suggested that the processed, waste biomass of the algae, could be a good biosorbent for its indium absorption properties. This had the double advantages of both recovery of indium (high economic importance), and also definition of a virtuous circular economic innovative strategy, whereby a waste becomes a valuable resource.

Chitin and chitosan are biopolymers that have diverse applications in medicine, agriculture, food, cosmetics, pharmaceuticals, wastewater treatment and textiles. With bio-origins, they easily blend with biological systems and show exemplified compatibility which is mandatory when it comes to biomedical research. Chitin and chitosan are ecofriendly, however the processes that are used to recover them aren’t ecofriendly. The focus of this work is to attempt an ecofriendly, sustainable phytomediated one pot recovery of chitosan from commercial chitin and from crab and shrimp shells and squid pen solid wastes. Graviola extracts have been employed, given the fact file that their active ingredients acetogenins actively interact with chitin in insects (resulting in its application as an insecticide). With that as the core idea, the graviola extracts were chosen for orchestrating chitin recovery and a possible chitin to chitosan transformation. The results confirm that graviola extracts did succeed in recovery of chitosan nanofibers from commercial chitin flakes and recovery of chitosan particles directly from solid marine wastes of crab, shrimp and squids. This is a first time report of a phyto-extract mediated novel chitosan synthesis method.

Wastewater treatment plants (WWTPs) in industrial parks provide centralized treatment for industrial and domestic wastewater. However, the information on toxicity reduction of wastewater and its correlation with treatment process in industrial park is limited. This study compared the toxicity reduction of wastewater in 12 industrial park WWTPs based on battery of toxicity assays. Nine toxic endpoints involving microorganism, phytoplankton, zooplankton, plant and human cell lines were applied. All the influents of WWTPs induced high toxicities, which were significantly reduced after the treatments from 7 of the studied WWTPs. However, the effluents of five WWTPs induced higher toxicity in one or more toxic endpoints compared to the influents. This study also found that most of anaerobic-anoxic-oxic (A2/O)-based processes had good removal efficiency of wastewater toxicity, while the sequencing batch reactor (SBR)-based processes had the lowest removal efficiency. Moreover, low correlation coefficients were obtained among all toxic endpoints, indicating that battery of toxicity assays was necessary to completely characterize the toxicity and risk of wastewater in industrial parks. This study shed new lights to the toxicity reduction of wastewater and its correlation with treatment process, which is very useful for the design, management and operation of WWTPs in industrial parks.

As algal biotechnology develops, there is an increasing requirement to conserve cultures without the cost, time and genetic stability implications of conventional serial transfers, including issues regarding potential loss by failure to regrow, contamination on transfer, mix up and/or errors in the documentation on transfer. Furthermore, it is crucial to ensure both viability and functionality are retained by stored stock-cultures. Low temperature storage, ranging from the use of domestic freezers to storage under liquid nitrogen, is widely being used, but the implication to stability and function rarely investigated. We report for the first time, retention of functionality in the maintenance of master stock-cultures of an industrially relevant, lipid-producing alga, under a variety of cryopreservation regimes. Storage in domestic (−15 °C), or conventional −80 °C freezers was suboptimal, with a rapid reduction in viability observed for samples at −15 °C and a >50% loss of viability, within one month, for samples stored at −80 °C. No reduction in viability occurred at −196 °C. Post-thaw culture functional performance was also influenced by the cryopreservation approach employed. Only samples held at −196 °C responded to nitrogen limitation in terms of growth characteristics and biochemical profiles (lipid production and chlorophyll a) comparable to the untreated control, cultured prior to cryopreservation. These results have important implications in microbial biotechnology, especially for those responsible for the conservation of genetic resources.

Carbon nanotubes (CNTs) have been applied in a wide range of fields, such as materials, electronics, energy storages, and biomedicine. With the rapid increase in CNTs industrialization, more and more CNT-containing wastewater is being produced. Since concerns about the toxic effects of CNTs on human health persist, CNT-containing wastewater should not be released into the environment without purification, but no effective methods have been reported. In the present study, we report a simple method to eliminate CNTs from industrial or laboratorial wastewater using sodium hypochlorite. Direct treatment of aqueous dispersions with sodium hypochlorite solution completely degraded CNTs into carbon oxides or carbonates ions. Since hypochlorite is environmentally friendly and frequently used as a disinfectant or bleaching agent in domestic cleaning, this method is practical for purification of CNT-contaminated industrial wastewater.

The large volume of municipal sludge causes environmental problems in cities worldwide. In this study, municipal sludge, mixed with construction waste residue, was used as substrate to plant Ailanthus altissima. The growth of A. altissima, the substrate characteristics, and substrate microbial diversity were measured to investigate potential recycling and reusing pathways of municipal sludge. The obtained results showed that compared to garden soil, the mixed substrate was weakly alkaline, and had higher nutrient contents, which is beneficial for A. altissima, and results in better growth in mixed substrate. Although the contents of the main heavy metals in the mixed substrate were significantly higher than in garden soil, the values met the criterion of Class II soil in the Environmental Quality Standard for the Soils of China (GB15618-1995). Different substrates showed a variety of microbial diversities. Proteobacteria was the top microbial phylum in all samples, and higher relative abundances were found in samples containing municipal sludge. After growing A. altissima, the relative abundances of Acidobacteria and Gemmatimonadetes increased in the mixed substrate. Therefore, addition of construction waste residue and growth of A. altissima caused a difference. The microbial communities in the mixed substrate with A. altissima are both plant friendly and environmentally friendly. These results suggest this mixed substrate as a potentially feasible and effective pathway for the reuse and recycling of municipal sludge for vegetation restoration.

With a conceptual shift in sewage treatment from ‘waste pollution’ to ‘vehicle of resource and energy recovery’ and the further intensification of the energy crisis, the separation and recovery of carbon resources from discharged sewage has gained increasing recent attention in the field of water treatment. The ultra-short Solids Retention Time (SRT) activated sludge process (SRT ≤ 4 d) is highly efficient for separating organic matter and improving the energy recovery rate in wastewater treatment plants, but the effluent quality is relatively poor. If organics in the ultra-short SRT effluent can be reduced further to separate and recover carbon resources, the process may soon replace the traditional activated sludge process. We conducted physical adsorption carbon recovery experiments in an ultra-short SRT (SRT = 2 d) activated sludge system using three carbon nanotubes. Considering that Chemical Oxygen Demand (COD) arises from a mixture of organic compounds, and because humic acid (HA) makes up a large fraction of the effluent and can cause great environmental harm, further experiments were conducted on the adsorption of HA in the effluent COD to three nanotubes. This study proposes a novel method to completely remove organics from the effluent from ultra-short SRT activated sludge processes and reveals nanotube adsorption properties and mechanisms.

Three different treatment technologies, namely mono-algae culture, algal-bacterial culture, and algal-fungal culture, were applied to remove pollutants form synthetic domestic sewage and to remove CO2 from biogas in a photobioreactor. The effects of different initial influent C/N ratios on microalgal growth rates and pollutants removal efficiencies by the three microalgal cultures were investigated. The best biogas upgrading and synthetic domestic sewage pollutants removal effect was achieved in the algal-fungal system at the influent C/N ratio of 5:1. At the influent C/N ratio of 5:1, the algal-fungal system achieved the highest mean chemical oxygen demand (COD) removal efficiency of 81.92% and total phosphorus (TP) removal efficiency of 81.52%, respectively, while the algal-bacterial system demonstrated the highest mean total nitrogen (TN) removal efficiency of 82.28%. The average CH4 concentration in upgraded biogas and the removal efficiencies of COD, TN, and TP were 93.25 ± 3.84% (v/v), 80.23 ± 3.92%, 75.85 ± 6.61%, and 78.41 ± 3.98%, respectively. These results will provide a reference for wastewater purification ad biogas upgrading with microalgae based technology.

Pectin content is an important quality index of fruits, as pectin content undergoes significant changes during the peach ripening process. The commonly used carbazole colorimetry method measures only the total content value of each kind of pectin for each pulp sample and cannot provide distribution maps of the pectin contents for the whole fruit pulp. This work used the hyperspectral imaging technique to quantitatively visualize the distribution maps of pectin contents inside peach pulp at the pixel level. The protopectin contents were well predicted, with the best residual predictive deviation of 2.264, whereas the predictions of the water-soluble pectin and the total pectin contents were not satisfied. On the basis of the best predictive model, the distribution maps of the protopectin contents were quantitatively visualized. A histogram of an example protopectin distribution revealed the existence of a wide range of protopectin contents in peach pulp. Our results show that hyperspectral imaging holds promise as a powerful alternative to the carbazole colorimetry method for measuring the spatial variations in the protopectin distribution inside peach pulp. The distribution maps could be used as a maturity indicator to understand and evaluate the ripening process of peach fruit in depth.

The economic factor of the microalgae harvesting step acts as a barrier to scaling up microalgae-based technology designed for wastewater treatment. In view of that, this study presents an alternative microalgae-bacteria system, which is proposed for eliminating the economic obstacle. Instead of the microalgae-bacteria (activated algae) flocs, the study aimed to develop activated algae granules comprising the microalgae Chlorella sp. as a target species. The presence of the filamentous microalgae (Phormidium sp.) was necessary for the occurrence of the granulation processes. A progressive decrease in frequency of the free Chlorella sp. cells was achieved once with the development of the activated algae granules as a result of the target microalgae being captured in the dense and tangled network of filaments. The mature activated algae granules ranged between 600 and 2,000 µm, and were characterized by a compact structure and significant settling ability (21.6 ± 0.9 m/h). In relation to the main aim of this study, a microalgae recovery efficiency of higher than 99% was achieved only by fast sedimentation of the granules; this performance highlighted the viability of the granular activated algae system for sustaining a microalgae harvesting procedure with neither cost nor energy inputs.

Filamentous bulking caused by Thiothrix species is responsible for sludge washout and loss of performance in dairy wastewater treatment plants. A long-term study was conducted over 1.5 years to test three different mitigation strategies in a full-scale plant composed of two parallel sequential batch reactors (SBR1 and 2). Strategies based on polyaluminium chloride addition and volatile fatty acids reduction were ineffective to permanently solve the problem. On the contrary, modification of the reactor cycle based on the implementation of a periodic starvation proved efficient to solve the biomass wash-out and drastically reduce the sludge volume index in both reactors. Bacterial diversity analysis using 16S amplicon sequencing and quantitative PCR indicated a reduction of Thiothrix abundance from 51.9 to 1.0% in SBR1 and from 71.8 to 0.6% in SBR2. Simultaneously, the abundance of the glycogen-accumulating bacterium Candidatus Competibacter increased in both reactors. Microscopy analysis confirmed the transition between a bulking sludge towards a granular-like sludge. This study confirms the applicability of a periodic starvation to (1) solve recurring Thiothrix bulking, (2) convert loose aggregates into dense and compact granular-like structures and (3) considerably reduce energy demand for aeration.

With the recent COVID-19 pandemic that has swept the world and the nation, hospitals around the country have experienced shortages in Personal Protective Equipment, specifically N95 filter face-mask respirators (FFRs). This has created the need for facilities to develop sterilization processes to enable reuse of face masks by the health care personnel. Among the various methods of sterilization, UVC light exposure is the easiest to implement given the factors of time, safety, and availability. Face masks and/or other PPE are exposed to UVC light for a specified time to kill any viruses or bacteria that may reside on the surfaces of the masks. A collaborative effort was formed in April of 2020 between Wellstar Health System and Kennesaw State University to (1) setup an appropriate sterilization room at a Wellstar hospital (2) develop the procedural guidelines necessary to ensure quality control and (3) assess employees’ perceptions of the N95 FFR decontamination process and efficacy. This paper will first describe the methodology used to validate the layout of the room, which consists of a rudimentary analytical analysis of the UVC photon intensity from bulb-to-mask, computer simulations to determine the lighting power density throughout the room, and experimental measurements to confirm the appropriate energy deposition. This paper will then document the procedures for handling and processing the pre- and post-sterilized masks followed by employee survey findings. It is the hope of the authors that this paper will serve to provide a generic blueprint for hospitals and other organizations to follow if a future need arises for rapid UVC decontamination.

Product architecture is defined as allocation of components to functions and their interfaces. But what makes this formulation insufficient for automobile architecture is their multi-layered allocation of components and the visual aspect of the architecture. This paper suggests, through an empirical study of two- wheeler models being manufactured by a prominent manufacturer, a multi-tiered framework along with a visual template for two- wheeler architecture which includes their visual schema as well. This paper investigates and demonstrates that this framework and template satisfy the requirements of product architecture by using examples from the domain of motorcycle design. Further, this paper investigates the utility of this framework for platforming strategy, innovation, adoption of new technology and standardization.

14 pages, 8 figures, supplementary information https://doi.org/10.1038/s41598-021-03777-9.-- Data availability: The Supplementary tables and figures can be found under the https://doi.org/10.6084/m9.figshare.14987001 in the public repository Figshare. To further facilitate exploration and viewing of Cehalopods Global Trade Networks by users from outside the academy or with basic technical knowledge, we have launched a fully operational web application at https://aospina.shinyapps.io/CGTN_app/.-- Correction: A network analysis of global cephalopod trade. Scientific Reports 12: 2329 (2022). https://doi.org/10.1038/s41598-022-06289-2, The global trade in cephalopods is a multi-billion dollar business involving the fishing and production of more than ten commercially valuable species. It also contributes, in whole or in part, to the subsistence and economic livelihoods of thousands of coastal communities around the world. The importance of cephalopods as a major cultural, social, economic, and ecological resource has been widely recognised, but research efforts to describe the extent and scope of the global cephalopod trade are limited. So far, there are no specific regulatory and monitoring systems in place to analyse the traceability of the global trade in cephalopods at the international level. To understand who are the main global players in cephalopod seafood markets, this paper provides, for the first time, a global overview of the legal trade in cephalopods. Twenty years of records compiled in the UN COMTRADE database were analysed. The database contained 115,108 records for squid and cuttlefish and 71,659 records for octopus, including commodity flows between traders (territories or countries) weighted by monetary value (USD) and volume (kg). A theoretical network analysis was used to identify the emergent properties of this large trade network by analysing centrality measures that revealed key insights into the role of traders. The results illustrate that three countries (China, Spain, and Japan) led the majority of global market movements between 2000 and 2019. Based on volume and value, as well as the number of transactions, 11 groups of traders were identified. The leading cluster consisted of only eight traders, who dominated the cephalopod market in Asia (China, India, South Korea, Thailand, and Vietnam), Europe (the Netherlands, and Spain), and the USA. This paper identifies the countries and territories that acted as major importers or exporters, the best-connected traders, the hubs or accumulators, the modulators, the main flow routes, and the weak points of the global cephalopod trade network over the last 20 years. This knowledge of the network is crucial to move towards an environmentally sustainable, transparent, and food-secure global cephalopod trade, AO was supported by H2020 Marie Skłodowska-Curie Actions (746361) and Contract financed through the call for postdoctoral fellowships of the Government of the Balearic Islands, program “Vicenç Mut” 2020. SV, GA, PP, CP and FLM knowledge the financial support from the INTERREG Cephs and Chefs Project (EAPA 282/2016), and Xunta de Galicia Grupos de Referencia Competitiva (under Grant ED431C2019/11). PP was supported by Xunta de Galicia (RECREGES II project under Grant ED481B2018/017). CP acknowledges FCT for the research contract 2020.02510.CEECIND. CP and FLM would also like to acknowledge FCT/MCTES national funds for the financial support to CESAM (UIDP/50017/2020 + UIDB50017/2020), With the institutional support of the ‘Severo Ochoa Centre of Excellence’ accreditation (CEX2019-000928-S)

This paper presents a multi-functional bi-anisotropic metasurface having ultra-wide out of band transmission characteristics. The proposed metasurface is comprised of 90° rotated T-shaped configuration yielding greater than or equal to 50% out-of-band transmission from above L- to X-band. Moreover, this metasurface achieves a maximum of 99% out-of-band transmission at lower frequency bands (i.e., L-band). The simultaneous absorptive and controlled reflection functionalities are achieved at 15.028 to 15.164 GHz along with polarization-insensitive and angular stable properties. The proposed metasurface yields state-of-the-art features compared to already published papers and has broader scope for Fabry Perot cavity, Radar cross-section (RCS) reduction, electromagnetic compatibility and interference (EMC/I) shielding, selective multi-frequency bolometers, ultrathin wave trapping filters, sensors and beam-splitters in the microwave domain.

For most bioinformatics statistical methods, particularly for gene expression data classification, prognosis, and prediction, a complete dataset is required. The gene sample value can be missing due to hardware failure, software failure, or manual mistakes. The missing data in gene expression research dramatically affects the analysis of the collected data. Consequently, this has become a critical problem that requires an efficient imputation algorithm to resolve the issue. This paper proposed a technique considering the local similarity structure that predicts the missing data using clustering and top K nearest neighbor approaches for imputing the missing value. A similarity-based spectral clustering approach is used that is combined with the K-means. The spectral clustering parameters, cluster size, and weighting factors are optimized, and after that, missing values are predicted. For imputing each cluster’s missing value, the top K nearest neighbor approach utilizes the concept of weighted distance. The evaluation is carried out on numerous datasets from a variety of biological areas, with experimentally inserted missing values varying from 5 to 25%. Experimental results prove that the proposed imputation technique makes accurate predictions as compared to other imputation procedures. In this paper, for performing the imputation experiments, microarray gene expression datasets consisting of information of different cancers and tumors are considered. The main contribution of this research states that local similarity-based techniques can be used for imputation even when the dataset has varying dimensionality and characteristics.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

In this paper, the hybrid combination of genetic algorithm and particle swarm optimization (GAPSO) is used to optimize the phase distribution (PD) of beam-scanning reflectarray. The GAPSO takes advantage of both conventional algorithms and it could cover their weaknesses. Two novel PDs are proposed in this paper which constant phase elements (CPEs) and ordinary elements (OEs) are two basic kinds of elements used in them. The phases of CPEs are fixed and it is not changed during beam scanning and only OEs’ phase could be adjusted to scan the main beam. In this work GAPSO and two novel PDs are applied to array factor’s PD of a 30 × 30 reflectarray antenna to displace the main beam electronically in the vertical plane from − 40° to 40°. Also, in these two novel PDs, 28.8% of total elements are selected as CPEs. In the first one with only CPEs, the phase of OEs (71.2% of total elements) could adjust, but in the second novel PD with CPEs and phase symmetry plane 35.5% of the total elements’ phase could be changed to scan the beam. Optimization results show that the novel PD and hybrid algorithm have appropriate performance in the electronically beam scanning of reflectarrays.

The act of measurement on a quantum state is supposed to “dephase” (dephasing refers to the phenomenon that the states lose phase coherence; then the phases get randomized in interaction with a bath of other oscillators, which is referred to as “decoherence”), then “decohere” and “collapse” (or more precisely “register” and “reduce”) the state into one of several eigenstates of the operator corresponding to the observable being measured. This measurement process is sometimes described as outside standard quantum-mechanical evolution and not calculable from Schrödinger’s equation. Progress has, however, been made in studying this problem with two main calculation tools—one uses a time-independent Hamiltonian, while a rather more general approach proving that decoherence occurs under some generic conditions. The two general approaches to the study of wave-function collapse are as follows. The first approach, called the “consistent” or “decoherent”’ histories approach, studies microscopic histories that diverge probabilistically and explains collapse as an event in our particular history. The other, referred to as the “environmental decoherence” approach studies the effect of the environment upon the quantum system, to explain wave-function decoherence which is produced by irreversible effects of various sorts. However, as we know, wave-function collapse is not related to thermal connection with the environment, rather, it is inherent to how measurements are performed by macroscopic apparata. In the “environmental decoherence” approach, one studies decoherence using a Markovian-approximated Master equation to study the time-evolution of the reduced density matrix (post dephasing) and obtains the long-time dependence of the off-diagonal elements of this matrix. The calculation in this paper studies the evolution of a quantum system starting with “dephasing” followed by the effects of the environment with some differences from prior analyses. We start from the Schrödinger equation for the state of the system, with a time-dependent Hamiltonian that reflects the actual microscopic interactions that are occurring. Then we systematically solve (exactly) for the time-evolved state, without invoking a Markovian approximation when writing out the effective time-evolution equation, i.e., keeping the evolution unitary until the end. This approach is useful, and it shows that the system wave-function will explicitly “un-collapse” if the measurement apparatus is sufficiently small. However, in the limit of a macroscopic system, this “dephasing” quickly leads to “decoherence”—collapse is a temporary state that will simply take extremely long (of the order of multiple universe lifetimes) to reverse. This has been attempted previously and our calculation is particularly simple and calculable. We make some connections to the work by Linden et al. while doing so. The calculation in this paper has interesting implications for the interpretation of the Wigner’s friend experiment, as well as the Mott experiment, which is explored in “Connection to some general theoretical results” and “Recurrence times” (especially the enumerated points in “Recurrence times”). The upshot is that as long as Wigner’s friend is macroscopically large (or uses a macroscopically large measuring instrument), no one needs to worry that Wigner would see something different from his friend. Indeed, Wigner’s friend does not even need to be conscious during the measurement that she conducts. It also allows one to reasonably interpret some of the more recent thought experiments proposed. In particular, as a result of the mathematical analysis, the short-time behavior of a collapsing system, at least the one considered in this paper, is not exponential. Instead, it is the usual Fermi-golden rule result. The long-term behavior is, of course, still exponential. This is a second novel feature of the paper—we connect the short-term Fermi-golden rule (quadratic-in-time behavior) transition probability to the exponential long-time behavior of a collapsing wave-function in one continuous mathematical formulation.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

This paper proposes a new method for converting a time-series into a weighted graph (complex network), which builds on electrostatics in physics. The proposed method conceptualizes a time-series as a series of stationary, electrically charged particles, on which Coulomb-like forces can be computed. This allows generating electrostatic-like graphs associated with time-series that, additionally to the existing transformations, can be also weighted and sometimes disconnected. Within this context, this paper examines the structural similarity between five different types of time-series and their associated graphs that are generated by the proposed algorithm and the visibility graph, which is currently the most popular algorithm in the literature. The analysis compares the source (original) time-series with the node-series generated by network measures (that are arranged into the node-ordering of the source time-series), in terms of a linear trend, chaotic behaviour, stationarity, periodicity, and cyclical structure. It is shown that the proposed electrostatic graph algorithm generates graphs with node-measures that are more representative of the structure of the source time-series than the visibility graph. This makes the proposed algorithm more natural rather than algebraic, in comparison with existing physics-defined methods. The overall approach also suggests a methodological framework for evaluating the structural relevance between the source time-series and their associated graphs produced by any possible transformation.

Grand challenges have become the de facto standard for benchmarking image analysis algorithms. While the number of these international competitions is steadily increasing, surprisingly little effort has been invested in ensuring high quality design, execution and reporting for these international competitions. Specifically, results analysis and visualization in the event of uncertainties have been given almost no attention in the literature. Given these shortcomings, the contribution of this paper is two-fold: (1) we present a set of methods to comprehensively analyze and visualize the results of single-task and multi-task challenges and apply them to a number of simulated and real-life challenges to demonstrate their specific strengths and weaknesses; (2) we release the open-source framework challengeR as part of this work to enable fast and wide adoption of the methodology proposed in this paper. Our approach offers an intuitive way to gain important insights into the relative and absolute performance of algorithms, which cannot be revealed by commonly applied visualization techniques. This is demonstrated by the experiments performed in the specific context of biomedical image analysis challenges. Our framework could thus become an important tool for analyzing and visualizing challenge results in the field of biomedical image analysis and beyond.