Search

This work presents the results of paper laser processing. It begins with the selection and examination of the processing parameters, then an examination of the properties of the modified papers and examples of applications of the developed modification method. The properties of laser-modified paper were studied using reflectance spectrophotometry to examine the colour aspects of the modified papers, scanning electron microscopy (SEM) and confocal microscopy for a morphological analysis, and Raman spectroscopy to analyse the papers under the influence of laser light. The influence of laser processing on the wettability of paper and the evenness of unprinted and printed paper was also investigated. The knowledge gained on paper surface modification with laser light was used to propose several applications, such as methods of marking, tactile detection, the controlled removal of optical brightener, ink, and metallised coatings from paper packaging, highlighting the design and aesthetics of paper. The developed laser-assisted method shows a promising, ecological approach to the design of many value-added paper products. [ABSTRACT FROM AUTHOR]

In this study, Al paper and cellulose acetate (CA) filters derived from heated tobacco waste were successfully converted into current collectors and active materials for a supercapacitor device. Typically, heated tobacco contains electrically discontinuous Al paper. First, Al was extracted from the tobacco waste using HCl to produce Lewis acid (AlCl3). This acid was then used in an Al electrodeposition process utilizing the chloroaluminate ionic liquid reaction between the acid and the base (RCl) at room temperature. To enhance the conductivity, a supplementary coating of Al metal was applied to the Al paper through electrodeposition, thus re-establishing the electrical continuity of the discontinuous parts and forming an Al-coated current collector. Moreover, the CA filters were carbonized under a nitrogen atmosphere, yielding carbon precursors (C-CA) for the supercapacitor electrodes. To further enhance the electrochemical performance, nickel oxide (NiO) was incorporated into C-CA, resulting in C-CA@NiO with pseudocapacitance. The specific surface area of CA increased with carbonization and the subsequent incorporation of NiO. The as-synthesized C-CA and C-CA@NiO materials were applied to an Al-coated current collector to obtain C-CA- and C-CA@NiO-based electrodes, exhibiting stable electrochemical behavior in the voltage range of −1.0 to 0 V and 0 to 1.0 V, respectively. An asymmetric supercapacitor (ASC) device was assembled with C-CA@NiO and C-CA as the positive and negative electrodes, respectively. This ASC device demonstrated a high specific capacitance of 40.8 F g−1, while widening the operating voltage window to 2.0 V. The high electrochemical performance of the device is attributed to the successful Al electrodeposition, which facilitates the electrical conductivity and increased porosity of the C-CA@NiO and C-CA materials. To the best of our knowledge, this is a pioneering study in regards to the conversion of biomass waste into current collectors and active materials to fabricate a practical ASC device. Our findings highlight the potential of reusing Al paper and CA filters from heated tobacco waste as essential components of energy storage devices. [ABSTRACT FROM AUTHOR]

The formation of a cellular hierarchically organized NiO film on a carbon paper substrate under hydrothermal conditions using triethanolamine as a base has been studied. The thermal behavior of the carbon paper substrate with the applied semi-product shell was studied using synchronous thermal analysis (TGA/DSC) and it was demonstrated that such modification of the material surface leads to a noticeable increase in its thermal stability. Using scanning electron microscopy (SEM), it was shown that the NiO film grown on the carbon fiber surface is characterized by a complex cellular morphology, organized by partially layered individual nanosheets of about 4–5 nm thickness and lateral dimensions up to 1–2 μm, some edges and folds of which are located vertically relative to the carbon fiber surface. The surface of the obtained material was also examined using atomic force microscopy (AFM), and the electronic work function of the oxide shell surface was evaluated using the Kelvin probe force microscopy (KPFM) method. The electrochemical parameters of the obtained flexible NiO/CP electrode were analyzed: the dependence of the specific capacitance on the current density was determined and the stability of the material during cycling was studied, which showed that the proposed approach is promising for manufacturing hierarchically organized electrodes for flexible supercapacitors. [ABSTRACT FROM AUTHOR]

This paper examines the impact of the CO2 laser parameters on the tensile strength, which is one of the most important properties of paper packaging in the process of cutting paper material. The study was performed on a paper material sample Fbb Board/Ningbo Spark C1S Ivory Board by examination of the influence of four independent variables: paper material grammage, cutting speed, laser power, and resolution on the tensile strength by using definitive screening design. Optimum process conditions of four variables that maximize the tensile strength were predicted and validated accordingly. Results confirm that laser power, paper material grammage, and cutting speed are the main process parameters that mostly affect the tensile strength. Besides individual parameters, two statistically significant interactions were obtained: laser power and cutting speed, and cutting speed and laser resolution. Maximum tensile strength values (20.37 N/mm) were achieved using the laser power of 60.6%, cutting speed of 3.24%, resolution of 2500 Hz, and a paper material grammage of 326.85 g/m2. With laser power at middle values and at a lower speed, a maximum tensile strength value can be obtained. Increasing the laser power and cutting speed will produce a slight lowering of tensile strength. [ABSTRACT FROM AUTHOR]

The surface-enhanced Raman scattering (SERS) properties of low-dimensional semiconducting MXene nanoflakes have been investigated over the last decade. Despite this fact, the relationship between the surface characteristics and SERSing performance of a MXene layer has yet to be comprehensively investigated and elucidated. This work shows the importance of surface morphology on the overall SERS effect by studying few-layer Ti3C2Tx MXene-based SERS substrates fabricated by vacuum-assisted filtration (VAF) and spray coating on filter paper. The VAF deposition results in a dense MXene layer suitable for SERS with high spot-to-spot and substrate-to-substrate reproducibility, with a significant limit of detection (LoD) of 20 nM for Rhodamine B analyte. The spray-coated MXenes film revealed lower uniformity, with a LoD of 50 nM for drop-casted analytes. Moreover, we concluded that the distribution of the analyte deposited onto the MXene layer is affected by the presence of MXene aggregates created during the deposition of the MXene layer. Accumulation of the analyte molecules in the vicinity of MXene aggregates was observed for drop-casted deposition of the analyte, which affects the resulting SERS enhancement. Ti3C2Tx MXene layers deposited on filter paper by VAF offer great potential as a cost-effective, easy-to-manufacture, yet robust, platform for sensing applications. [ABSTRACT FROM AUTHOR]

This paper discusses the results of the micro-Raman analysis performed on paper-like graphene oxide (GO) samples consisting of many functionalised graphene layers and annealed at moderate temperatures (≤500 °C) under vacuum conditions (p ≃ 10−4 mbar). The analysis of the standalone samples revealed that the obtained material is characterised by a noticeable disorder level but still stays below the commonly accepted threshold of high or total disorder. GO formed in a simple way showed two spectral bands above 1650 cm−1 recorded very rarely or not at all and their origin has been discussed in detail. The results also confirmed the metastable character of multilayer GO after the annealing process at moderate temperatures as the C/O ratio was kept between 2 and 3 and the spectral features were stable within the annealing temperature range. [ABSTRACT FROM AUTHOR]

The applications of waste-derived fuel from paper mills in industrial boilers benefit the reduction of carbon emissions. However, the co-combustion of waste-derived fuel and coal causes significant changes in the characteristics of the ash and brings about the need to find possible means of the utilization of the ash produced. In this work fly, ash samples were collected from circulating fluidized bed (CFB) boilers co-combusting paper mill wastes with coal and analyzed in detail. The chemical, physical, and thermal characteristics of two different co-combustion fly ashes (CCFA) were investigated using X-ray fluorescence (XRF), X-ray diffraction (XRD), thermogravimetry (TG), and scanning electron microscope (SEM). The chemical composition of CCFA is largely affected by the fuel source type. Thermal analyses of CCFA show that the type of desulfurization system used by the boiler influences the form of sulfate present in the fly ash. The presence of calcium sulfite hemihydrate can cause a high loss in the ignition of CCFA. By comparing the physical requirements specified in the ASTM standard for coal fly ash to be used in concrete, the CCFA produced from paper mill wastes was found to show good potential as supplementary cementitious materials. [ABSTRACT FROM AUTHOR]

The dynamic mechanical behavior and cushioning performance of honeycomb sandwich panels, which are extensively employed in product cushioning packaging due to their exceptional energy absorption capabilities, were examined using a combination of experimental and numerical methods. Several factors, such as maximum acceleration–static stress, cushioning coefficient–static stress, and other curves, were analyzed under various impact conditions. The simulated stress–strain, deformation modes, cushioning coefficients, and other parameters demonstrate consistency with the experimental results. The acceleration, maximum compression, and cushioning coefficient obtained from the experiment and simulation calculation were 30.68 g, 15.44 mm, and 2.65, and 31.96 g, 14.91 mm, and 2.79, respectively. The results indicate that all error values were less than 5%, confirming the precision and reliability of the model. Furthermore, the model was utilized to simulate and predict the cushioning performance of honeycomb sandwich panels with different cell structures and paper thicknesses. These results provide a solid basis for enhancing the design of subsequent honeycomb element structures. [ABSTRACT FROM AUTHOR]

The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill's anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods. [ABSTRACT FROM AUTHOR]

The main objective of the presented research was to find a model that describes the maximum compressive force of paper in its plane. The research began with crushing tests of a number of packaging paper samples of various lengths. It was shown that due to the specific structure of the paper and the high heterogeneity of its structure, packaging paper is material where it is difficult to determine the maximum compressive stress. Next, three analytical models describing the load capacity of a flat paper web were investigated and an alternative empirical model was proposed. The results of the performed tests are directly applicable in the calculation of the mechanical properties of corrugated cardboard and the determination of the load capacity of cardboard packaging. [ABSTRACT FROM AUTHOR]

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, "fusilli calabresi" type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS–PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS–PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food. [ABSTRACT FROM AUTHOR]

Thermochromic inks (TC) have received increasing attention in recent years, particularly in the design and packaging industries. Their stability and durability are crucial for their application. This study highlights the detrimental effects of UV radiation on the lightfastness and reversibility of thermochromic prints. Three commercially available TC inks with different activation temperatures and in different shades were printed on two different substrates, cellulose and polypropylene-based paper. Used inks were vegetable oil-based, mineral oil-based and UV-curable. The degradation of the TC prints was monitored using FTIR and fluorescence spectroscopy. Colorimetric properties were measured before and after exposure to UV radiation. The substrate with a phorus structure exhibited better colour stability, suggesting that the chemical composition and surface properties of the substrate play a crucial role in the overall stability of thermochromic prints. This can be explained by the ink penetration into the printing substrate. The penetration of the ink into the structure (cellulose fibres) protects the ink pigments from the negative effect of the UV radiation. Obtained results suggest that although the initial substrate may appear suitable for printing, its performance after ageing may not be optimal. In addition, the UV curable prints show better light stability than those made of mineral- and vegetable-based inks. In the field of printing technology, understanding the interplay between different printing substrates and inks is critical to achieve high-quality, long-lasting prints. [ABSTRACT FROM AUTHOR]

Sulfate attack is one of the drawbacks of cementitious materials for stabilized soils. In the current study, a durability comparison of stabilized soil with cement (Type IV) and waste paper fly ash (WPFA) was conducted. First, the treated soil's unconfined compressive strength (UCS) was tested. Next, the treated soil was subjected to various wetting/drying cycles with various sulfate concentrations and temperatures for a year. In the meantime, samples were taken for DRX, FTIR, and TGA microstructural analyses. Additionally, samples were manufactured to track swelling over an 800 day period. The outcomes show that WPFA's UCS remained constant. Furthermore, ettringite development can be seen in the microstructural studies, however testing on linear displacement over 800 days revealed no significant changes in swelling. Finally, SEM was used to verify the ettringite formation at 360 days in order to confirm the previous findings. All the results indicated that stabilizing soil with 5% of WPFA and 3% of cement IV is possible even in presence of high sulfate concentrations, while maintaining the durability of the structure. [ABSTRACT FROM AUTHOR]

Flexible calcium carbonate (FCC) was developed as a functional papermaking filler for high loaded paper, which was a fiber-like shaped calcium carbonate produced from the in situ carbonation process on the cellulose micro-or nanofibril surface. Chitin is the second most abundant renewable material after cellulose. In this study, a chitin microfibril was utilized as the fibril core for making the FCC. Cellulose fibrils for the preparation of FCC were obtained by fibrillation of the TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical) treated wood fibers. The chitin fibril was obtained from the β-chitin from the born of squid fibrillated in water by grinding. Both fibrils were mixed with calcium oxide and underwent a carbonation process by the addition of carbon dioxide, thus the calcium carbonate attached on the fibrils to make FCC. When used in papermaking, both the FCC from chitin and cellulose gave a much higher bulk and tensile strength simultaneously than the conventional papermaking filler of ground calcium carbonate, while maintaining the other essential properties of paper. The FCC from chitin caused an even higher bulk and higher tensile strength than those of the FCC from cellulose in paper materials. Furthermore, the simple preparation method of the chitin FCC in comparison with the cellulose FCC may enable a reduction in the use of wood fibers, process energy, and the production cost of paper materials. [ABSTRACT FROM AUTHOR]

In protecting cultural heritage, deacidification is used to stabilize acidic papers, ensuring the neutralization of acids present in the paper. But in the process of aging, several mechanisms of degradation occur simultaneously. Therefore, substances used to stabilize the paper should contain an antioxidant component in addition to the deacidifying component. The effect of the antioxidant (hindered amine light stabilizers—HALS type) on the stabilization of lignin-containing acid papers during accelerated aging was studied in this work. The effective deacidification component was magnesium; the solvent was hexamethyldisiloxane (HMDSO). The 4-amino-2,2,6,6-tetramethylpiperidine series of hindered amine light stabilizers (HALS) was selected as appropriate for creating a modifying system based on HMDSO. The modification system was tested on samples of a model test acid lignin-containing paper (NOVO) and naturally aged acidic paper from the real book. The addition of substances to the proposed deacidification system has a favorable effect on stabilizing the pH during aging and provides the inhibition of the oxidative degradation products and stabilization of the cellulose degree of polymerization. It was confirmed that the application of the system containing deacidification and an antioxidant component may increase the effectiveness of the protection of acid groundwood paper heritage objects. Adding a tested antioxidant to the proposed deacidification system has a favorable effect on stabilizing the pH value for a long time in accelerated aging. [ABSTRACT FROM AUTHOR]

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties. [ABSTRACT FROM AUTHOR]

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties. [ABSTRACT FROM AUTHOR]

The advancement of agricultural mesh technology has contributed to its improved properties. As a result, agricultural nets are widely adopted in large-scale farming applications, for example, in cereal crop farming. However, a consequence of this increased use of agricultural nets is the accumulation of large amounts of waste. The current paper focuses on the recycling of agricultural nets used in wrapping straw bales to develop additives and fillers in cement composites. The research details an analysis of the use of waste agricultural meshes as an ingredient in cement composites. Six test series of different mixtures were conducted. In the first four series, agricultural waste was utilised as an additive in a composite comprising aggregate and cement slurry (the amounts of wasted nets were 20, 40, 60, and 80 kg/m3). In the last test series, the recyclate utilised comprised a mixture of cement slurry and waste only. The composites were subjected to standard tests and thermal resistance tests. The results showcased that that the addition of a net worsened the workability of the concrete mixture, and with increasing amounts of addition, the consistency of the mixture could change from liquid to dense plastic. The flexural strength of the composite decreased with increasing amounts of recyclate. In subsequent test series, the flexural strength value was lower than that of the control (3.93 MPa), from 7.38% (3.64 MPa) for the composite with 20 kg/m3 of recyclate to 37.66% (2.45 MPa) for the composite with of 80 kg/m3 recyclate. The flexural strength value of the net-filled composite without aggregate was very high (10.44 MPa), where the value obtained for the control composite was 62.36% lower. The results of the compressive strength test showed a decrease in this parameter with increasing amounts of additive. The value assessed for the control composite was 27.99 MPa. As expected, the composite that had no aggregate and consisted of only recycled filler had the lowest compressive strength. The value of this parameter was 13.07 MPa, and it was 53.31% lower than that of the control composite. The results of the tests of resistance to temperatures were similar to those recorded for the composites with polypropylene fibres. All composites demonstrated a significant decrease in their compressive and flexural strength after annealing. SEM imaging showed that the net fibres were closely bonded to the cement stone. Finally, it was concluded that recyclates performed best as fillers in lightweight composites with a low density, low absorption, high flexural strength, and satisfactory compressive strength. [ABSTRACT FROM AUTHOR]

All-lignin coating formulations were prepared while combining water-soluble cationic kraft lignin (quaternized LignoBoost®, CL) and anionic lignosulphonate (LS). The electrostatic attraction between positively charged CL and negatively charged LS led to the formation of insoluble self-organized macromolecule aggregates that align to films. The structures of the formed layers were evaluated by atomic force microscopy (AFM), firstly on glass lamina using dip-coating deposition and then on handsheets and industrial uncoated paper using roll-to-roll coating in a layer-by-layer mode. Coated samples were also characterized by optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (SEM/EDS), and contact angle measurements. It was suggested that the structure of all-lignin aggregates is the result of the interaction of amphiphilic water-soluble lignin molecules leading to their specifically ordered mutual arrangement depending on the order and the mode of their application on the surface. The all-lignin coating of cellulosic fiber imparts lower air permeability and lower free surface energy to paper, mainly due to a decrease in surface polarity, thus promoting the paper's hydrophobic properties. Moderate loading of lignin coating formulations (5–6 g m−2) did not affect the mechanical strength of the paper. [ABSTRACT FROM AUTHOR]

The title of the current Special Issue, "Feature Papers in Materials Simulation and Design", has identified the aims of this collection since its opening: the gathering of research works and comprehensive review papers that advance the understanding and prediction of material behavior at different scales, from atomistic to macroscopic, through innovative modeling and simulation. The paper by Chen et al. [[4]] aimed at studying the thermal properties and thermoelectric performance of imidazole-graphyne (ID-GY) by combining first principle calculations with the Boltzmann transport theory. The last paper by Cheng and Vescovini [[16]] presented instead an accurate and efficient numerical method for the analysis and design of Variable Stiffness (VS) laminates. Civalek et al. [[11]] developed an efficient eigenvalue algorithm for the axial vibration analysis of embedded short-fiber-reinforced micro-/nano-composite rods subjected to arbitrary boundary conditions. [Extracted from the article]

Flexible respiratory monitoring devices have become available for outside-hospital application scenarios attributable to their improved system wearability. However, the complex fabrication process of such flexible devices results in high prices, limiting their applications in real-life scenarios. This study proposes a flexible, low-cost, and easy-processing paper-based humidity sensor for sleep respiratory monitoring. A paper humidity sensing model was established and sensors under different design parameters were processed and tested, achieving high sensitivity of 5.45 kΩ/%RH and good repeatability with a matching rate of over 85.7%. Furthermore, the sensor patch with a dual-channel 3D structure was designed to distinguish between oral and nasal breathing from origin signals proved in the simulated breathing signal monitoring test. The sensor patch was applied in the sleep respiratory monitoring of a healthy volunteer and an obstruct sleep apnea patient, demonstrating its ability to distinguish between different respiratory patterns as well as various breathing modes. [ABSTRACT FROM AUTHOR]

The preparation of graphene materials from biomass resources is still a challenge, even more so if they are going to be employed as supports for electrocatalysts for water splitting. Herein, we describe the preparation and characterization of graphene oxides (GOs) from solid macroalgae waste obtained after processing an agar–agar residue. The structural and morphological characterization of the obtained GO confirm the presence of a lamellar material that is composed of few layers with an increased number of heteroatoms (including nitrogen) if compared with those observed in a GO obtained from graphite (reference). Three-dimensional electrodes were prepared from these GOs by depositing them onto a fibrous carbon paper, followed by electrodeposition of the catalyst, NiFe. The electrocatalytic performance of these hybrid systems for the oxygen evolution reaction (OER) showed a proactive effect of both graphene materials toward catalysis. Moreover, the electrode prepared from the algae-based graphene showed the highest electrocatalytic activity. This fact could be explained by the different structure of the algae-based graphene which, due to differences in the nucleation growth patterns and electroactive sites developed during the electrodeposition process, produced more reactive NiFe species (higher oxidation state). [ABSTRACT FROM AUTHOR]

In order to further improve the performance of impregnated paper decorated blockboard (ecological board), high-density fiberboard (HDF) was selected as the equilibrium layer to replace the commonly used poplar veneer. Results showed that the performance of HDF ecological board can be comparable to that of poplar veneer ecological board. It had good appearance quality, and its surface scratch resistance, surface wear resistance, water resistance and mechanical properties met the requirements of National Standard GB/T 34722-2017. The surface cracking resistance of the ecological board prepared with HDF as the equilibrium layer reached the highest level (grade 5), far better than that of the poplar veneer ecological board. This was because HDF was a relatively homogeneous material, and its dry shrinkage in both the transverse direction and along the grain direction was much lower than that of the poplar veneer. This characteristic of HDF made it possible to improve the dimensional stability and bending resistance of blockboard substrates under dry and hot conditions. The formaldehyde emission of the HDF ecological board was higher than that of the poplar veneer ecological board, but it met the formaldehyde emission requirements of indoor materials according to GB 18580-2001. [ABSTRACT FROM AUTHOR]

In this study, high-pressure laminates (HPL) impregnated with phenol-formaldehyde (PF) resins enriched with kraft lignin were developed. Pulverised kraft lignin was added to the commercial PF resin in the amounts of 1% and 5% (solid to solid). Laminates were manufactured using pressure impregnation of the resins into the papers and using hot pressing of HPL in a laboratory press. Laminates with a lignin content of 1% (L-LPF-1) showed the highest bending strength (72.42 MPa) and Brinell hardness (9.41); they also exhibited the best moisture uptake (9.61) and thickness swelling after immersion in water (3.32%). Except for impact bending, laminates with a lignin content of 5% (L-LPF-5) had worse properties. However, the differences between the variants are mostly not statistically significant and are comparable with the results of commercial PF resin. Scanning electron microscopy confirmed the homogenous structure of produced laminates and the occurrence of cohesive failures in ruptured L-LPF-1 laminates, whereas in ruptured L-LPF-5 laminates adhesive failures were also observed. Based on the conducted research it can be said that the utilisation of kraft lignin as an additive to PF resin (in the amount of 1%) has a positive effect on the produced HPL. [ABSTRACT FROM AUTHOR]

The lightweight aggregates used by the civil engineering market are sintered at a high temperature, about 1200 °C. In times of high energy prices and regulation of carbon dioxide emissions, lightweight aggregate products of the high-temperature process in sales marketing are not readily accepted. This study developed a sintered-type paper sludge lightweight aggregate. In order to reduce energy consumption, substitution of some reservoir sediment clay in paper sludge substitutes is to be expected. The study used two types of paper sludge (green clay paper sludge and paper pulp sludge). The sintering temperature was reduced effectively as the green clay paper sludge was substituted for some of the reservoir sediment clay, and the optimum substitute ranges of green clay paper sludge were 10%-50%. The optimum substitute ranges of the paper pulp sludge were 10%-40%. Test results show that the properties of aggregates have a particle density of 0.66-1.69 g/cm3, a water absorption of 5%-30%, and a loss on ignition of 10%-43%. The loss on ignition of aggregate became greater with the increase in paper sludge content. This means that the calorific value provided by the paper sludge will increase as paper sludge content increases. Paper sludge can therefore be considered a good material to provide heat energy for sintering lightweight aggregate. [ABSTRACT FROM AUTHOR]

To study the friction and wear performance of carbon fiber reinforced friction materials under different working conditions, paper-based friction materials with different fibers were prepared. Experiments on the SAE#2 test bench were conducted to study the infectors including friction torques, surface temperature, coefficient of friction (COF), and surface morphologies. The results were analyzed, which indicated that the carbon fiber reinforced friction material could provide a higher friction torque and a lower temperature rising rate under the applied high pressure and high rotating speed conditions. As the pressure increased from 1 MPa to 2.5 MPa, the friction torque of plant fiber reinforced material increased by 150%, the friction torque of carbon fiber reinforced material increased by 400%, and the maximum temperature of plant fiber reinforced and carbon fiber reinforced material reached the highest value at 1.5 MPa. Thus, carbon fibers not only improved the COF and friction torque performance but also had advantages in avoiding thermal failure. Meanwhile, carbon fiber reinforced friction materials can provide a more stable COF as its variable coefficient (α) only rose from 38.18 to 264.62, from 1 MPa to 2.5 MPa, which was much lower than the natural fiber reinforced friction materials. Simultaneously, due to the good dispersion and excellent mechanical properties of PAN chopped carbon fibers, fewer pores formed on the initial surface, which improved the high wear resistance, especially in the intermedia disc. [ABSTRACT FROM AUTHOR]

In recent years, several studies have reported the recycling of by-products generated by the paper industry and their application to the construction industry. A majority of the existing studies used waste paper sludge ash, and considerable energy is consumed in such incineration processes. This may further contribute to air pollution. In this study, we used waste newspaper (WNP), which underwent a simple crushing process without a separate high-temperature treatment process, and we integrated it in cement mortar. We prepared mortars containing 0%, 0.2%, 0.4%, 0.6%, 0.8%, and 1.0% ground WNP as a cement substitute. Subsequently, the fluidity, compressive strength, tensile strength, carbonation depth, drying shrinkage, and microstructure of the mortars were compared and analyzed. The 28-day compressive strength of the mortar samples with WNP was approximately 3.2–16.1% higher than that of the control sample. The 28-day accelerated carbonation depth of the samples with WNP was approximately 1.03–1.61 mm. Furthermore, their carbonation resistance was approximately 5.2–39.4% higher than that of the control sample. Compressive strength, tensile strength, and carbonation resistance were improved by appropriately using ground WNP as a cement substitute in cement mortar. In this study, the appropriate amount of WNP according to the mechanical properties of cement mortar was found to be 0.4–0.8%, and considering the durability characteristics, the value 0.6 was the most ideal. [ABSTRACT FROM AUTHOR]

Worldwide, the need for thermal insulation materials used to increase the energy performance of buildings and ensure indoor thermal comfort is constantly growing. There are several traditional, well-known and frequently used thermal insulation materials on the building materials market, but there is a growing trend towards innovative materials based on agro-industrial waste. This paper analyses the performance of 10 such innovative thermal insulation materials obtained by recycling cellulosic and/or animal waste, using standardised testing methods. More precisely, thermal insulation materials based on the following raw materials were analysed: cellulose acetate, cigarette filter manufacturing waste; cellulose acetate, cigarette filter manufacturing waste and cigarette paper waste; cellulose acetate, waste from cigarette filter manufacturing, waste cigarette paper and waste aluminised paper; cellulose from waste paper (two types made by two independent manufacturers); wood fibres; cellulose from cardboard waste; cellulose from waste cardboard, poor processing, inhomogeneous product; rice husk waste and composite based on sheep wool, recycled PET fibres and cellulosic fibres for the textile industry. The analysis followed the performance in terms of thermal insulating quality, evidenced by the thermal conductivity coefficient (used as a measurable indicator) determined for both dry and conditioned material at 50% RH, in several density variants, simulating the subsidence under its own weight or under various possible stresses arising in use. The results showed in most cases that an increase in material density has beneficial effects by reducing the coefficient of thermal conductivity, but exceptions were also reported. In conjunction with this parameter, the analysis of the 10 types of materials also looked at their moisture sorption/desorption capacity (using as a measurable indicator the amount of water stored by the material), concluding that, although they have a capacity to regulate the humidity of the indoor air, under low RH conditions the water loss is not complete, leaving a residual quantity of material that could favour the development of mould. Therefore, the impact on indoor air quality was also analysed by assessing the risk of mould growth (using as a measurable indicator the class and performance category of the material in terms of nutrient content conducive to the growth of microorganisms) under high humidity conditions but also the resistance to the action of two commonly encountered moulds, Aspergillus niger and Penicillium notatum. The results showed a relative resistance to the action of microbiological factors, indicating however the need for intensified biocidal treatment. [ABSTRACT FROM AUTHOR]

The cutting performance of steel blades is an eternal, attractive topic in the knife industry. It is a complicated process to cut up materials because it usually involves the contact mechanics of the material been cut, the geometry and roughness of the blade edge and the hardness and wear resistance of the blade steel. Therefore, a comprehensive analysis is required to evaluate the cutting performance of knife blades. In this study, such an analysis was conducted based on a quantitative model to describe the cutting depth of paper cards containing SiO2 particles by steel blades, and major contributing factors were summarized. The effect of the micro-geometries of blade edges was thoroughly discussed, and a geometry factor ξ for the micro-geometry of a blade edge was introduced into the model. The experimental results indicated that mechanical processing could produce a rough blade edge and a higher ξ value, accordingly. A similar effect was caused by the carbides in the martensitic steels for blades, and the ξ value was found to increase linearly with the volumetric fraction of the carbides. The extraordinary cutting behavior of the 3V blade implied that fine coherent carbides may result in an efficient improvement (40–50%) in the total cutting depth. [ABSTRACT FROM AUTHOR]

The material most commonly used to filter and clean the intake air of vehicle internal combustion engines is pleated filter paper, which in most cases is shaped in the form of a cylinder or panel. The production technology has a low cost and is not complicated. In addition to high separation efficiency and filtration performance, pleated filter media are required to have low initial pressure drop, which depends on the geometry of the bed. Much research has been conducted in this area. Dust accumulated in the filter bed causes an increase in pressure drop, which is the cause of deformation and sticking of pleats. The lack of stability of the pleats, the need to strengthen them, and the need to obtain small sizes while achieving high efficiency and accuracy of filtration of engine intake air was the reason for the development of a different design and a new technology for making filter cartridges called PowerCore. The distinctive feature of these filters is axial flow in one direction of the air stream, which avoids turbulence and thus minimizes pressure drop. This paper presents a comparative analysis of a standard PowerCore and PowerCore G2 filter bed and two cylindrical filters with a pleated filter bed made of cellulose and polyester. The conditions and methodology of experimental testing of filters with test dust are presented. During the tests, the characteristics of separation efficiency and filtration performance, as well as pressure drop as a function of the mass of dust retained on the filter of two PowerCore filters and two cylindrical filters were performed. Three specimens of test filters with the same filtration area were made from each sample of filter bed. The results showed that in each test of the filter bed, there is an initial filtration period characterized by low (96–98%) initial separation efficiency and the presence of large (dpmax) dust grains. As the dust loading of the bed increases, the separation efficiency and filtration performance obtain higher and higher values. The initial period of filtration ends when the conventional value (99.9%) of separation efficiency is reached. The duration of this period depends on the type of filter bed and for the PowerCore G2 filter ends for a dust loading of km = 33.1 g/m2, and for the cellulose filter for km = 117.3 g/m2. During the initial period, the air behind the PowerCore G2 filter contains grains with sizes in the range of dpmax = 9–16 µm. Behind the cellulose filter, dust grains are much larger, dpmax = 17–35 µm. The total operating time of the PowerCore G2 filter, limited by the achievement of the permittivity resistance Δpwdop = 3 kPa, is twice that of the other filter compositions tested. [ABSTRACT FROM AUTHOR]

Flexible poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)/polypyrrole/paper (PEDOT:PSS/PPy/paper) thermoelectric (TE) nanocomposite films were prepared by a two-step method: first, PPy/paper nanocomposite films were prepared by an in situ chemical polymerization process, and second, PEDOT:PSS/PPy/paper TE composite films were fabricated by coating the as-prepared PPy/paper nanocomposite films using a dimethyl sulfoxide-doped PEDOT:PSS solution. Both the electrical conductivity and the Seebeck coefficient of the PEDOT:PSS/PPy/paper TE nanocomposite films were greatly enhanced from 0.06 S/cm to ~0.365 S/cm, and from 5.44 μV/K to ~16.0 μV/K at ~300 K, respectively, when compared to the PPy/paper TE nanocomposite films. The thermal conductivity of the PEDOT:PSS/PPy/paper composite film (0.1522 Wm-1K-1 at ~300 K) was, however, only slightly higher than that of the PPy/paper composite film (0.1142 Wm-1K-1 at ~300 K). As a result, the ZT value of the PEDOT:PSS/PPy/paper composite film (~1.85 × 10-5 at ~300 K) was significantly enhanced when compared to that of the PPy/paper composite film (~4.73 × 10-7 at ~300 K). The as-prepared nanocomposite films have great potential for application in flexible TE devices. [ABSTRACT FROM AUTHOR]

The topic of waste combustion/co-combustion is critical, given the increasingly restrictive legal regulations regarding its environmental aspects. In this paper, the authors present the test results of selected fuels of different compositions: hard coal, coal sludge, coke waste, sewage sludge, paper waste, biomass waste and polymer waste. The authors conducted a proximate and ultimate analysis of the materials and mercury content in them and their ashes. An interesting element of the paper was the chemical analysis of the XRF of the fuels. The authors conducted the preliminary combustion research using a new research bench. The authors provide a comparative analysis of pollutant emissions—especially mercury emission—during the combustion of the material; this is an innovative element of this paper. The authors state that coke waste and sewage sludge are distinguished by their high mercury content. The value of Hg emission during the combustion depends on the initial mercury content in the waste. The results of the combustion tests showed the adequacy of mercury release compared to the emissions of other compounds considered. Small amounts of mercury were found in waste ashes. The addition of a polymer to 10% of coal fuels leads to a reduction in mercury emissions in exhaust gases. [ABSTRACT FROM AUTHOR]

In the present work, the possibility of increasing the calcium carbonate (CaCO3) content in sheets of paper to optimize their properties was investigated. A new class of polymeric additives for papermaking is proposed as well as a method for their use in paper sheet containing the CaCO3 precipitated addition. Calcium carbonate precipitated (PCC) and fibers cellulose were adjusted with a cationic polyacrylamide flocculating agent (polydiallyldimethylammonium chloride (plyDADMAC) or cationic polyacrylamide (cPAM)). PCC was obtained in the laboratory by a double-exchange reaction between calcium chloride (CaCl2) and sodium carbonate (Na2CO3) suspension. After testing, the dosage of PCC was established at 35%. To improve the systems of additives studied, the materials obtained were characterized and their optical and mechanical properties were analysed. The PCC had a positive influence over all of the paper samples, but in the case of use of cPAM and polyDADMAC polymers the paper obtained had superior properties compared to the paper obtained without additives. Also, the samples obtained in the presence of cationic polyacrylamide exhibit superior properties to those obtained in the presence of polyDADMAC. [ABSTRACT FROM AUTHOR]

Interest towards cellulose nanofibers obtained from virgin and waste sources has seen a significant growth, mainly thanks to the increasing sensitivity towards the concept of circular economy and the high levels of paper recycling achieved in recent years. Inspired by the guidelines of the green building industry, this study proposes the production and characterization of TEMPO-oxidized and homogenized cellulose nanofibers (TOHO CNF) from different sources and their use as additives for earth plasters on two different raw earth samples, characterized by geotechnical laboratory tests and mineralogical analysis: a high-plasticity clay (T2) and a medium-compressibility silt (ABS). Original sources, including those derived from waste (recycled cardboard and paper mill sludge), were characterized by determining chemical content (cellulose versus ashes and lignin) and fiber morphology. TOHO CNF derived from the different sources were compared in terms of nanofibers medium diameter, crystallinity degree, thermal decomposition and oxidation degree, that is the content of carboxylic groups per gram of sample. Then, a preliminary analysis of the influence of CNF on earth plasters is examined. Adhesion and capillary absorption tests highlighted the effect of such nanofibers on blends in function of two factors, namely the cellulose original source and the oxidation degree of the fibers. In particular, for both earth samples, T2 and ABS, a significant increase in adhesion strength was observed in the presence of some TOHO CNF additives. As far as capillary sorption tests, while an undesired increase in water adsorption was detected for T2 compared to the control, in the case of ABS, a significant reduction in water content was measured by adding TOHO CNF derived from recycled sources. These results pave the way for further in-depth investigation on the role of TOHO CNF as additives for earth plasters. [ABSTRACT FROM AUTHOR]

Natural fibers do not have a long life in soil; therefore, they cannot replace synthetic textiles in many applications. However, in order to solve ever-increasing global environmental problems due to microplastics, more and more natural polymers must be used, creating a need for research into the sustainable life extension of natural fibers. Lignin is, along with cellulose, a main component of wood, and is produced in large quantities as waste during paper production. With appropriate processing, lignin can be exploited/used as a textile auxiliary to combine the strength-enhancing properties of textiles made from natural fibers with the protective properties of a lignin coating. However, there is not yet sufficient research on how to integrate lignin into textile applications. For this purpose, in this study, we have investigated whether thermoplastic lignin can be processed as a surface protective coating. We tested lignin as a yarn coating to extend the service life of cellulosic textiles. Cotton yarns have been coated with lignin in variations of coating mass, characterized and investigated by means of soil burial tests. As the soil burial tests conducted in climate chamber and outdoor field environments showed, the lifespan of textiles made from natural fibers can be significantly extended with a lignin coating. Long-term resilience has been demonstrated in standard burial tests. In the outdoor tests, the lignin coating was still fully intact, even after about 160 days of burial. The textile materials coated in this way enable sustainable applications, especially for geotextiles. They have an adjustable, sufficiently long service life; however, they are still biodegradable, and can therefore replace some applications, such as vegetating trench/brook slopes, with synthetic materials. Lignin-coated textiles have the potential to significantly reduce the carbon footprint, reduce not only the dependence on petroleum-based products but also the amount of microplastics entering the environment. Further research can be conducted to improve lignin compounding in terms of other interesting properties for specific textile applications. Process optimization could increase the protective effect and further extend the life of useful textiles in soil. [ABSTRACT FROM AUTHOR]

The active mass of the plates of aspent car battery with higher wear after an efficient desulfatization can be used as sources of a new electrode. This paper proposes the recycling of spent electrodes from a lead acid battery and the incorporation of NiO or Co3O4 contents by the melt-quenching method in order to enrich the electrochemical properties. The analysis of X-ray diffractograms indicates the gradual decrease in the sulfated crystalline phases, respectively, 4PbO·PbSO4 and PbO·PbSO4 phases, until their disappearance for higher dopant concentrations. Infrared (IR) spectra show a decreasing trend in the intensity of the bands corresponding to the sulfate ions and a conversion of [PbO3] pyramidal units into [PbO4] tetrahedral units by doping with high dopant levels, yielding to the apparition of the PbO2 crystalline phase. The observed electron paramagnetic resonance (EPR) spectra confirm three signals located on the gyromagnetic factor, g~2, 2.2 and 8 assigned to the nickel ions in higher oxidation states as well as the metallic nickel nanoparticles. This compositional evolution can be explained by considering a process of the drastic reduction in nickel ions from the superior oxidation states to metallic nickel. The linewidth and the intensity of the resonance lines situated at about g~2, 2.17, 4.22 and 7.8 are attributed to the Co+2 ions from the EPR data. The best reversibility of the cyclic voltammograms was highlighted for the samples with x = 10 mol% of NiO and 15 mol% of Co3O4, which are recommended as suitable in applications as new electrodes for the lead acid battery. [ABSTRACT FROM AUTHOR]

Organic solvents with high purity are essential in various fields such as optical, electronic, pharmaceutical, and chemical areas to prevent low-quality products or undesired side-products. Constructing methods to remove impurities such as water residue in organic solvents has been a significant challenge. Within this article, we report for the first time a new method for the preparation of hydrophobic and oleophilic filter paper (named OCFP), based on thermally induced silane dehydrocoupling between cellulose-based filter paper and octadecylsilane. We comprehensively characterized OCFP using various characterization techniques (FTIR, XPS, XRD, and EDS). OCFP showed super-hydrophobic and oleophilic properties as well as remarkable water separation and removal efficiency (>93%) in various organic solvents with sustained reusability. In addition, the analytical results both before and after filtration of an NMR solvent using OCFP indicated that OCFP has an excellent solvent drying efficiency. This work presents a new strategy for the development of super-hydrophobic cellulose-based filter paper, which has great potential for solvent drying and water separation. [ABSTRACT FROM AUTHOR]

A Xi-shaped meta structure, has been introduced in this paper. A modified split-ring resonator (MSRR) and a capacitive loaded strip (CLS) were used to achieve the left-handed property of the metamaterial. The structure was printed using silver metallic nanoparticle ink, using a very low-cost photo paper as a substrate material. Resonators were inkjet-printed using silver nanoparticle metallic ink on paper to make this metamaterial flexible. It is also free from any kind of chemical waste, which makes it eco-friendly. A double negative region from 8.72 GHz to 10.91 GHz (bandwidth of 2.19 GHz) in the X-band microwave spectra was been found. Figure of merit was also obtained to measure any loss in the double negative region. The simulated result was verified by the performance of the fabricated prototype. The total dimensions of the proposed structure were 0.29λ x 0.29 λ x 0.007 λ. It is a promising unit cell because of its simplicity, cost-effectiveness, and easy fabrication process. [ABSTRACT FROM AUTHOR]

This work reports a modification of a fibrous cellulose material (paper) by the addition of polyacrylonitrile (PAN) fibres doped with 10,12–pentacosadiynoic acid (PDA). The fibres are sensitive to ultraviolet (UV) light. When the paper containing PAN–PDA is irradiated with UV light it changes colour to blue as a consequence of interaction of the light with PDA. The colour intensity is related to the absorbed dose, content of PAN–PDA fibres in the paper and the wavelength of UV radiation. The features of the paper are summarised after reflectance spectrophotometry and scanning microscopy analyses. All the properties of the modified paper were tested in accordance with adequate ISO standards. Moreover, a unique method for assessing the unevenness of the paper surface and the quality of printing was proposed by using a Python script (RGBreader) for the analysis of RGB colour channels. The modification applied to the paper can serve as a paper security system. The modified paper can act also as a UV radiation indicator. [ABSTRACT FROM AUTHOR]

Conductive paper has the advantages of being low-cost, lightweight, disposable, flexible, and foldable, giving it promising potential in future electronics. However, mainstream conductive papers are opaque and rigid, which seriously affect the wide application of conductive paper. In this paper, we demonstrate a highly transparent, flexible, and conductive paper, fabricated by mixing cellulose nanofibers (CNFs) with silver nanowires (AgNWs) and then plasticizing with choline chloride/urea solvent. The as-prepared CNF/AgNW paper showed high transparency (~90% transmittance) and flexibility (~27% strain), and low sheet resistance (56 Ω/sq). Moreover, the resistance change of CNF/AgNW paper increased only ~1.1% after 3000 bending−unbending cycles under a 150° large angle, implying a long working life and stability. In view of this, our methodology has the potential to open a new powerful route for fabrication of paper-based green electronics. [ABSTRACT FROM AUTHOR]

A new approach for the chemical modification of the surface of paper based on the application of colloidal mixtures containing cationic starch and polyoxometalates on uncoated base paper is presented. Polyoxometalates with the Keggin-type structure and physical properties similar to those presented by coating pigments, namely H3PW12O40∙23H2O, H4SiW12O40∙24H2O, and K7PW11O39∙9H2O, have been used in order to improve the quality of inkjet printing. The analysis of the different samples by FTIRATR spectroscopy showed the presence of the polyoxometalates (and the cationic starch) on the top surface of the paper. In addition, the determination of surface energy parameters, namely the polar component (σsp) and the dispersive component (σsd) of the surface energy, by contact angle measurements revealed that, for the new samples, the polar component level was much higher than that of the uncoated base paper. The quality of inkjet printing, evaluated by parameters such as the gamut area and the optical density, was considerably improved by these surface treatments. [ABSTRACT FROM AUTHOR]

The goal of this study was to analyze the effects of cellulose fibers loading by precipitation in-situ of calcium carbonate over the properties of printing paper obtained from mixtures of the softwood and hardwood fibers. The effects of fibers with in-situ loading were analyzed comparatively with conventional paper loading respectively, by adding precipitated calcium carbonate into fiber stock. The effectiveness of the methods was evaluated by various analyses and investigations: calcium carbonate content, Scanning electron microscope (SEM) images, X-ray diffraction, optical and mechanical properties of the paper sheets. The evaluation of the effects on paper properties led to the conclusion that, at the same filler content, the in-situ loading method gives higher opacity and brightness than conventional methods. The utilization of cellulose fibers with in-situ loading as additive, shown as a modification of the ratio between fibers with in-situ loading and fibers without loading, regardless of whether they are softwood or hardwood fibers, allowed us to optimize printing paper properties, especially regarding the relationship between optical and strength properties. [ABSTRACT FROM AUTHOR]

Currently, the pulp and paper industry generates around 50–70 million tons of lignin annually, which is mainly burned for energy recovery. Lignin, being a natural aromatic polymer rich in functional hydroxyl groups, has been drawing the interest of academia and industry for its valorization, especially for the development of polymeric materials. Among the different types of polymers that can be derived from lignin, polyurethanes (PUs) are amid the most important ones, especially due to their wide range of applications. This review encompasses available technologies to isolate lignin from pulping processes, the main approaches to convert solid lignin into a liquid polyol to produce bio-based polyurethanes, the challenges involving its characterization, and the current technology assessment. Despite the fact that PUs derived from bio-based polyols, such as lignin, are important in contributing to the circular economy, the use of isocyanate is a major environmental hot spot. Therefore, the main strategies that have been used to replace isocyanates to produce non-isocyanate polyurethanes (NIPUs) derived from lignin are also discussed. [ABSTRACT FROM AUTHOR]

In this study, the polymer PTSPM-PMETAC with anion adsorption properties was prepared by a one-step method, then the amino-modified nano-SiO2 was grafted onto the polymer to improve the roughness of the surface and enhance the stability of superhydrophobic properties, and a high-stability superhydrophobic paper with ion-induced wettability transition properties was successfully prepared. The study found that the paper can realize the reversible control of surface wettability through the exchange between the anions PF6− and Cl− adsorbed on the surface of PMETAC, and further investigation of the effect of different solvents on the ion exchange properties found that water was the poor solvent for ion exchange, while the mixtures of methanol, acetone, and methanol & water were the good solvent. On the whole, the preparation of superhydrophobic paper by this method not only simple in preparation process, low in cost and strong in universality, but also the prepared superhydrophobic paper has high transparency and good stability, which has great application potential in industrial production. [ABSTRACT FROM AUTHOR]

This paper reports a plasma treatment (PT) method for improving the surface hydrophilicity and mechanical properties of cellulose in reconstituted tobacco paper-base. The absorption and infiltration rates of water droplets on PT-reconstituted tobacco paper-base-15 s were significantly accelerated. Notably, the increased content of methylene and alkyl groups enabled the tobacco paper-base to absorb more useful substrates in the tobacco extract after plasma treatment. In addition, the tensile mechanical performance of reconstituted tobacco was significantly improved after plasma treatment, which indicated that the content of organic matter absorbed by the tobacco paper-base sheet was increased. Moreover, tobacco extract infiltrated on the surface of PT-reconstituted tobacco paper-base reached 37.7° within 30 s, while it reached 79.9° on the reconstituted tobacco paper-base. Finally, the mechanism by which the surface hydrophilicity and mechanical properties of the cellulose in the tobacco paper-base were improved is discussed. [ABSTRACT FROM AUTHOR]

This document is an editorial introducing a special issue of the journal "Materials" titled "Advances in Thermal and Mechanical Properties of Polymeric Materials." The issue features papers on various topics related to the thermomechanical and electrical properties of polymers and their composites. The papers cover subjects such as the use of waste polyethylene in composites, predicting thermal comfort in sportswear, the impact of water temperature on viscoelastic pipes, and the effects of pressure and temperature on material density and thermal conductivity. Other papers discuss luminescent hybrid materials, behavior of plaster-based composites against water, properties of thermoplastic starch nanocomposites, decontamination of recycled polypropylene, mechanical properties of 3D-printed composites, combustion of fuels and waste materials, production of parts with varied transparency using polypropylene injection molding, and thermal conductivity of filaments used in fused deposition modeling. The editorial concludes by congratulating the authors and inviting scientists to contribute to future issues. It is important to note that the opinions and data presented in the document are those of the individual authors and contributors, and not of MDPI or the editor. MDPI and the editor disclaim responsibility for any harm caused by the ideas, methods, instructions, or products mentioned in the content. [Extracted from the article]

In kraft paper mills, supersonic steam jets are used to remove deposits that build up on the heat exchanger tubes in the recovery boiler. In this study, the fracture toughness KC and work of fracture, WF, of simulated boiler deposits were measured at temperatures up to 500 °C to determine the optimal conditions for deposit removal. The model deposits experienced an important brittle to ductile transition at ~450 °C. Above this temperature, ductile deposits required lower peak force, but four times more energy to fracture when compared to those tested at lower temperatures. The transition was clear in scanning electron micrographs of the fracture surfaces. The findings have significant implications for mills wishing to optimize sootblower performance. [ABSTRACT FROM AUTHOR]

In this study, CaO-containing wastes from pulp and paper industries such as fly ash (FA) and calcined lime mud (LM) were utilized to neutralize and purify acidic wastewaters from the pickling processes in steel mills. The investigations were conducted by laboratory scale trials using four different batches of wastewaters and additions of two types of CaO-containing waste materials. Primary lime (PL), which is usually used for the neutralization, was also tested in the same experimental set up in the sake of comparison. The results show that these secondary lime sources can effectively increase the pH of the acidic wastewaters as good as the commonly used primary lime. Therefore, these secondary lime sources could be potential candidates for application in neutralization processes of industrial acidic wastewater treatment. Moreover, concentrations of metals (such as Cr, Fe, Ni, Mo and Zn) can decrease dramatically after neutralization by using secondary lime. The LM has a purification effect from the given metals, similar to the PL. Application of fly ash and calcined lime mud as neutralizing agents can reduce the amount of waste from pulp and paper mills sent to landfill and decrease the need for nature lime materials in the steel industry. [ABSTRACT FROM AUTHOR]

In this work, we present a systematic study on solid Surface Enhanced Raman Scattering (SERS) substrates consisting of Au and Ag nanoparticles (NPs) loaded on filter paper with the dip-coating method. The aim of this work is to explore how a series of parameters (e.g., concentration of colloidal solution, different porosity of filter paper, and the presence of an aggregating agent) affects the analytical performance of paper-based SERS substrates. All the substrates developed in this study have been analyzed with two non-resonant probe molecules, 4-mercaptobenzoic acid (4-MBA) and adenine, in terms of (i) inter-sample repeatability, (ii) intra-sample repeatability, (iii) sensitivity, and (iv) overall SERS performance in terms of analyte quantification. Moreover, the issue of how to evaluate the repeatability for a solid SERS substrate is carefully discussed. [ABSTRACT FROM AUTHOR]

The dynamic pore systems and high surface areas of flexible metal-organic framework materials make them excellent candidates to be used in different kinds of adsorption processes. However, the adsorption and desorption behaviors of therapeutic drugs on metal-organic frameworks in solution are not fully developed. Here, we systematically investigated the adsorption and desorption behaviors of a typical therapeutic drug, verapamil, over several Zr-based metal-organic frameworks [e.g., Zr-FUM, UiO-66(Zr), UiO-66(Zr)-NH2 and UiO-66(Zr)-2COOH] as well as ZrO2 in an acetonitrile solution by using paper spray mass spectrometry. In contrast to other materials, UiO-66(Zr)-2COOH demonstrated a superior adsorption performance to verapamil due to their strong acid-base and/or hydrogen-bond interactions, and the adsorption process fitted well with the pseudo-second-order kinetic model. As verapamil-adsorbed materials were used for desorption experiments, ZrO2 demonstrated the most favorable desorption performance, whereas UiO-66(Zr)-2COOH yielded the poorest desorption capability. These Zr-based materials had also been coated at the surface with filter papers for the analysis of various drugs and proteins in the process of paper spray mass spectrometry. The results demonstrated that among the studied materials, ZrO2-coated paper gave the most favorable desorption performance as a pure drug solution, whereas the paper from UiO-66(Zr) demonstrated the optimal capability in the analyses of therapeutic drugs in a complex matrix (e.g., blood) and a protein (e.g., myoglobin). [ABSTRACT FROM AUTHOR]