Search

This paper proposes a novel consequent‐pole dual‐stator linear permanent magnet vernier machine (DS‐LPMVM) with PM in the mover slot opening, which has a bi‐directional flux modulation effect. The novelty of the proposed machine consists of consequent‐pole double‐sided topology with toroidal windings placed in the mover slot, as well as PMs both on the stator and mover slot to improve the air gap magnetic field. The dual‐stator adopts misalignment structure to suppress detent force and produce steady thrust. The electromagnetic parameters of the proposed DS‐LPMVM are evaluated and quantitatively compared with the conventional linear permanent magnet vernier machine (C‐LPMVM) in terms of air‐gap flux density, no‐load back EMF, inductance, and thrust. The geometrical parameters are designed to reduce the detent force. By analyzing the optimized structure parameters of the two machines, the good electromagnetic performances of the proposed machine are verified by the finite element method (FEM) and semi‐analytical method, and both results of the two methods are basically the same. It is found that the amount of PMs for the proposed machine is reduced by 20% compared to the C‐LPMVM, but the average thrust is increased by 20.7% and the thrust ripple is reduced to 4.04%. The results show that the proposed DS‐LPMVM has better flux modulation effect and thrust characteristics than C‐LPMCM. Finally, a 12‐slot, 10‐pole pairs prototype was manufactured and tested. © 2024 Institute of Electrical Engineers of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Halbach array has been more frequently used in the field of electromagnetism in recent days because of some unique advantages such as the self‐shielding and sinusoidal field distribution. In order to reduce the impact of the high order harmonic content of the air‐gap flux density of the interior permanent magnet synchronous motor (IPMSM) on the performance of the machine, a new non‐uniform Halbach array structure is proposed in this paper. Firstly, an equivalent analytical model is established to analyze the influence on the air‐gap flux density. At the same time, the interior permanent magnet synchronous motor model is built by using the finite element analysis. Then, the relationship between the air‐gap flux density and the four design parameters (the thickness of the permanent magnet, the magnetization angle, the angle of the permanent magnet, and the proportion of auxiliary magnetic poles) is analyzed by using the Taguchi method orthogonal experiment. The total harmonic distortion (THD) of air‐gap magnetic fields and its fundamental harmonic amplitude are employed as the evaluation criteria. Finally, the effectiveness of this optimization method is verified by comparing the harmonic content of the air‐gap flux density before and after the optimization. © 2021 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

Cogging torque can affect the performance of permanent magnet (PM) homopolar inductor machines (HIMs). In order to find the reduction methods of the PM HIM cogging torque, it is necessary to investigate its production mechanism and analytical model. In this paper, the production mechanism of the PM HIM cogging torque is revealed from the perspective of air‐gap field modulation principle. It is found that the air‐gap permeance of PM HIMs can modulate their air‐gap magneto‐motive force (MMF) and then a large number of modulated air‐gap magnetic fields are generated. These magnetic fields with identical production condition but different rotation speeds or rotation directions can interact with each other, hence the production of the PM HIM cogging torque. By the combination of energy method and air‐gap field modulation principle, the cogging torque analytical model of PM HIMs is derived. Based on the obtained analytical model, the methods for reducing the PM HIM cogging torque are further analyzed. Finally, a 48‐slot/4‐pole (48S4P) PM HIM is designed and exampled. The air‐gap flux density of the 48S4P PM HIM is simulated by three‐dimensional (3‐D) finite element analysis (FEA). Based on the harmonic analysis for the simulated results, the correctness of the proposed cogging torque production mechanism is validated. In addition, a prototype of the 48S4P PM HIM is manufactured. The cogging torque in the prototype is obtained by the analytical model, 3‐D FEA and experiments, respectively. The simulation and measurement results verify the correctness of the cogging torque analytical model. © 2023 Institute of Electrical Engineer of Japan and Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

The double‐sided permanent magnet linear synchronous motor (DS‐PMLSM) is widely used in the industrial field with high precision and long strokes due to simple construction, high instantaneous thrust and high controllability. However, parasitic issues, such as unavoidable manufacturing tolerances, might cause the symmetrical position deviation of primary or secondary components, which results in an asymmetrical air‐gap between components, affecting the motor's electromagnetic characteristics further. In this paper, it is taken into account secondary torsional or offset conditions (the secondary component is displaced sideways from a symmetrical position), and investigates the variations of electromagnetic characteristics on the 12‐solt 14‐pole short‐primary DS‐PMLSM. Based on the finite element method (FEM), the effects of secondary torsion or offset on the air‐gap flux density, the back‐EMF, the detent force, the thrust force, and the normal force are investigated and compared respectively. In addition, the analytical results of the back‐EMF considering lower secondary torsion are verified on a lower secondary torsional prototype. From the analytical results of electromagnetic characteristics, it is revealed that with the torsional angle or offset distance rising, the normal force and detent force in the Y‐axis gradually increase, while the thrust force and the back‐EMF decrease. These theoretical researches can play an important role in the operation and assembly process of the DS‐PMLSM. © 2022 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]

According to the air‐gap flux density (AGFD) and the thickness of the permanent magnet (PM) in the direction of magnetization, this paper proposes a modified analytical model for the sine pole‐shaping surface‐mounted permanent magnet motor (SPMM) under parallel magnetization. The construction of the model also involves the Carter coefficient formula, the principle of magnetic‐circuit equivalence, and the distributed magnetic‐circuit method, which are used to deal with such influential factors as stator slotting, interpolar magnetic leakage, edge effect, and magnetic‐circuit saturation. Then, a finite‐element model is established to verify the analytical model through simulation. The results show that the fundamental amplitude of AGFD of the modified sine pole‐shaping motor is respectively 6.4 and 0.15% higher than that of the simplified sine pole‐shaping motor and the eccentric pole‐shaping motor, and that the total harmonic distortion of AGFD the former is respectively 67.2 and 11.1% lower than that of the latter, thereby causing an increase in average torque of the sine pole‐shaping motor and a decrease in its radial electromagnetic harmonics and torque ripple. Experiments show that both the modified analytical and finite‐element model are accurate. And, the proposed analytical model which does not need ergodic scanning as the eccentric pole‐shaping method can further optimize the electromagnetic performance of the motor. It can not only improve the motor design but also provide reference for the optimal design of high‐quality PM motors. © 2022 Institute of Electrical Engineers of Japan. Published by Wiley Periodicals LLC. [ABSTRACT FROM AUTHOR]