Search

This paper summarises the results of a study to identify and quantify the potential impact of measures and policies to reduce the energy consumption of air conditioning in European countries over a 10-year period. The market penetration of air conditioning in Europe has increased steadily over several decades. On a “business as usual” basis, its energy consumption would increase by over 50% by 2020. Measures to restrict this increase are therefore important, but the savings potential straddles several overlapping areas which are subject to different constraints including those imposed by the replacement rates of systems and products, and the refurbishment rates of existing buildings. This work reported in this paper is based on the use of information from a variety of sources in a highly disaggregated model to assess the “realisable” savings over a 10-year period, taking into account relevant constraints. The paper summarises results at a European level, focussing on those cases that generate the greatest realisable savings. Savings are possible in three areas: improved equipment and system efficiency, reduced cooling loads, and more effective operation. The cases that offer the largest savings provide the basis for recommendations for policy measures, often using existing policy instruments. In addition, areas where further work is needed are identified. More detailed results and information about the study and additional recommendations can be found at http://www.bre.co.uk/searchresults.jsp?category=5&q=energy+management [1] . [ABSTRACT FROM AUTHOR]

Temperature and humidity independent control (THIC) systems demonstrate promising energy-saving potential compared with the conventional air conditioning systems. One type of THIC systems is proposed to use dual cooling sources with different temperatures since they could be produced easily by traditional vapor compression refrigeration chillers. This paper investigates the applicable condition of the THIC system based on dual cooling sources (DCSTHIC system). It is found that the DCSTHIC system has limited conditions (such as scopes of the heat moisture ratio and the fresh air rate) when applied, otherwise the indoor air temperature and humidity can’t be fulfilled, and further available scope of the heat moisture ratio realized by the DCSTHIC system is disclosed for air conditioned spaces. The minimum realized heat moisture ratio depends on the temperature of low-temperature cooling sources ( t LCS ). A parametric study is also conducted to analyze effects on the energy efficiency of DCSTHIC systems. These parameters include the heat moisture ratio ( ε ) and temperatures of dual cooling sources. Results show that DCSTHIC systems show more significant energy-saving potential in the air conditioned spaces with higher ε . The system COP improvement ranges from 3.1% to 17.5% compared with conventional air conditioning systems when the heat moisture ratio changes from 8000 kJ/kg to 15,000 kJ/kg. This study helps to guide the design and optimization of DCSTHIC systems. [ABSTRACT FROM AUTHOR]

This paper shows development of a simple, cheap “Building Energy Management System” (BEMS) to monitor energy consumption, and an application to measure energy consumption, including electricity and gas consumption in buildings. The system uses current transformers to measure electric consumption at each distribution box. Web cameras monitor lighting in each room, as well as air conditioning status by recognizing the movement of a ribbon at the outlet. Web cameras can also monitor gas consumption at the meter through character recognition. The data is sent via network to a computer for monitoring and analysis. As an example, key components of this BEMS were tested to measure building energy consumption of Osaka City University Sugimoto Campus in Japan for a period of 2 years (2013, 2014). The electric consumption of campus as well as the electric and gas consumption for air conditioning use was measured. Web cameras were installed in several rooms in one section of the campus to record lighting and air conditioning use data. The data was analyzed to reveal a correlation between hourly outdoor temperature and hourly electric consumption, with a stronger correlation between hourly outdoor temperature and hourly electric consumption for air conditioning. [ABSTRACT FROM AUTHOR]

Abstract: In Hong Kong, conventional air-conditioning (AC) systems cause a high energy consumption and poor indoor thermal comfort. This paper investigated the AC load profiles of three typical local commercial buildings, i.e. office, hotel and retail, and examined the energy consumption of liquid desiccant cooling system (LDCS) for these buildings. Simulation results showed that the cooling load contributed to more than 98% of total annual load, with high latent load proportion from March to September. The high reheating ratio, i.e. from 60% to 90%, is found to be the main reason for the poor thermal comfort. Therefore, the LDCS which could handle sensible and latent loads separately was proposed. However, the electricity-driven LDCS was found not suitable for local commercial buildings. significant energy saving could be achieved by the solar-assisted LDCS system with thermal storage, when the installation area for solar collectors is larger than the minimum required one, i.e. 9.7m2/(kWm−2) for office and 12.7m2/(kWm−2) for hotel buildings. Energy saving of different system types with different installation areas was also studied. The solar-assisted LDCS shows more energy saving in winter but less in summer. Results and conclusions can be useful for researchers and local engineers. [Copyright &y& Elsevier]

Abstract: Traditional houses and public buildings in Thailand were constructed from materials of low thermal mass and the walls were not insulated. Brick and concrete began to replace wood as walling material before air-conditioning was introduced into the country. New large buildings have glazed and closed windows so interior spaces require air-conditioning and forced ventilation. Up to the present, no insulation is used on walls. This paper presents results from an experimental and simulation study on comparative energy and economic performance of walls used to enclose air-conditioned spaces. The walls are externally and internally insulated to different thicknesses. The spaces are assumed to serve three commercial functions. Results show that insulation can generally help improve thermal performance of walls, but the function that a space serves dictates where insulation should be placed and how cost effective it is. [Copyright &y& Elsevier]

Abstract: This paper explores the potential of reducing the annual energy consumption of a central air-conditioned building through advanced evaporative cooling systems. The building considered is a typical three floor library building of a University. The regenerative evaporative cooling technology is coupled with the liquid cooled water chiller system to accomplish the energy conservation objective. Comparisons of the regenerative evaporative cooling are made with simple evaporative cooling to bring out the importance such a system. The well-known building simulation software, TRNSYS is used to carry out the heat load calculations and the dynamic simulations of the building. Annual energy consumptions of different components of the air-conditioning system are estimated for the existing water chiller system as well as for both coupled evaporative cooling systems (simple and regenerative). The annual energy consumptions, the indoor temperature, the relative humidity and the thermal comfort index ‘PMV’ are compared for all the three different air-conditioning systems. The coupling of direct and regenerative evaporative cooling technologies with water chiller system has shown, respectively, 12.09% and 15.69% savings in annual energy consumption of the building, while maintaining PMV between −1 and +1 for most of the hours in the year. [ABSTRACT FROM AUTHOR]