Search

Aiming at the demand for subjective evaluation of driveability for fuel cell vehicles, the modeling and evaluation method of driveability for fuel cell vehicles were studied in this paper. Firstly, a real-time model of the fuel cell vehicle powertrain system was established, which included the fuel cell model, power battery model, DC/DC converter model and drive motor model. Secondly, it was integrated with the vehicle dynamics model to form a virtual prototype of a fuel cell vehicle. And a virtual subjective evaluation platform for fuel cell vehicles was built by combining the virtual prototype and high-fidelity driving simulator. Thirdly, a subjective evaluation method of driveability for fuel cell vehicles was proposed, which included the starting performance, acceleration performance, uniform speed performance and tip-in/tip-out performance. Finally, the paper used the platform and method mentioned above to conduct subjective evaluations of the fuel cell vehicles. [ABSTRACT FROM AUTHOR]

This paper concerns the utilisation of a gas bladder hydraulic suppressor to mitigate oscillations in the delivery flow rate of positive displacement machines. The research focuses on two primary objectives: first, the experimental validation of the potential of this solution and second, the formulation of a one-dimensional fluid dynamic model for the suppressor. The foundational framework of the fluid dynamic model is based on the equations governing fluid motion with a one-dimensional approach. To accurately depict the fluid dynamics within the suppressor, a unique approach for determining the speed of sound was incorporated, and it implemented the instantaneous cross-sectional area and the inertial effect of the bladder. This paper is a development of a previous work to also investigate the positioning along the delivery pipe of the suppressor with respect to the pump. The study presents the performance of the suppressor and points out the effects of its relative position with respect to the pump that becomes particularly relevant at high speeds. [ABSTRACT FROM AUTHOR]

This paper delves into the critical role of tax credits, specifically Sections 45Q and 45V, in the financing and economic feasibility of low-carbon-intensity hydrogen projects, with a focus on natural-gas-based hydrogen production plants integrated with carbon capture and storage (CCS). This study covers the current clean energy landscape, underscoring the importance of low-carbon hydrogen as a key component in the transition to a sustainable energy future, and then explicates the mechanics of the 45Q and 45V tax credits, illustrating their direct impact on enhancing the economic attractiveness of such projects through a detailed net present value (NPV) model analysis. Our analysis reveals that the application of 45Q and 45V tax credits significantly reduces the levelized cost of hydrogen production, with scenarios indicating a reduction in cost ranging from USD 0.41/kg to USD 0.81/kg of hydrogen. Specifically, the 45Q tax credit demonstrates a slightly more advantageous impact on reducing costs compared to the 45V tax credit, underpinning the critical role of these fiscal measures in enhancing project returns and feasibility. Furthermore, this paper addresses the inherent limitations of utilizing tax credits, primarily the challenge posed by the mismatch between the scale of tax credits and the tax liability of the project developers. The concept and role of tax equity investments are discussed in response to this challenge. These findings contribute to the broader dialogue on the financing of sustainable energy projects, providing valuable insights for policymakers, investors, and developers in the hydrogen energy sector. By quantifying the economic benefits of tax credits and elucidating the role of tax equity investments, our research supports informed decision-making and strategic planning in the pursuit of a sustainable energy future. [ABSTRACT FROM AUTHOR]

Hydro-pneumatic energy storage is a form of compressed-air energy storage that can provide the long-duration storage required for integrating intermittent renewable energies into electrical power grids. This paper presents results based on numerical modelling and laboratory tests for a kilowatt-scale HPES system tested at the University of Malta. This paper presents measurements of the discharge cycle, in which energy stored in compressed air within a pressure vessel is hydro-pneumatically converted back into electricity via a Pelton turbine and fed into the national electricity grid. The tests were conducted using a hydraulic turbine operated under different fixed-turbine rotational speed settings, with the pressure being allowed to decrease gradually during the HPES system's discharge cycle. The system's overall efficiency accounted for flow losses, turbine inefficiencies, and electrical losses. The tests showed that this efficiency was practically independent of the compressed-air pressure of specific water turbine runner speeds, despite the water turbine operating at fixed speeds. A numerical model developed in MATLAB Simulink (R2022a) was also presented for use simulating the hydraulic performance of the system during the discharge cycle. The model used secondary loss coefficients for the hydraulic circuit and derived velocity coefficients from computational fluid dynamics (CFD) for the Pelton turbine nozzle. We achieved very good agreement between the predictions based on numerical modelling and the measurements taken during laboratory testing. [ABSTRACT FROM AUTHOR]

Hydrogen-powered mobility is believed to be crucial in the future, as hydrogen constitutes a promising solution to make up for the non-programmable character of the renewable energy sources. In this context, the hydrogen-fueled internal combustion engine represents one of the suitable technical solutions for the future of sustainable mobility. As a matter of fact, hydrogen engines suffer from limitations in volumetric efficiency due to the very low density of the fuel. Consequently, hydrogen-fueled ICEs can reach sufficient torque and power density only if suitable supercharging solutions are developed. Moreover, gaseous-engine performance can be improved to a great extent if direct injection is applied. In this perspective, a remarkable know-how has been developed in the last two decades on NG engines, which can be successfully exploited in this context. The objective of this paper is twofold. In the first part, a feasibility study has been carried out with reference to a typical 2000cc SI engine by means of 1D simulations. This study was aimed at characterizing the performance on the full load curve with respect to a baseline PFI engine fueled by NG. In this phase, the turbocharging/supercharging device has not been included in the model in order to quantify the attainable benefits in the absence of any limitation coming from the turbocharger. In the second part of this paper, the conversion of a prototype 1400cc direct injection NG engine, running with stoichiometric mixture, to run on a lean hydrogen combustion mode has been investigated via 1D simulations. The matching between engine and turbocharger has been included in the model, and the effects of two different turbomatching choices have been presented and discussed. [ABSTRACT FROM AUTHOR]

This paper is a summary of the last ten years of work on the study of parabolic trough collectors (PTCs) and compound parabolic collectors (CPCs) coupled to photovoltaic and thermal solar receiver collectors (SCR-PVTs). While reviewing the state of the art, numerous review papers were found that focused on conventional solar receiver collector (SRC) technology for solar thermal generation. However, there is a lack of review papers summarizing SRC-PVT hybrid technology for solar electric/thermal generation, which would be beneficial for researchers interested in this area of research. This paper provides a review of SRC-PVT hybrid technologies. The theoretical foundations for analyzing and modeling PTC and CPC concentrators coupled to SRC-PVT are described, with an emphasis on modeling through thermal resistances and energy balances. Additionally, this section provides a concise overview of previous studies that have addressed the modeling of PTC and CPC collectors coupled to SCR-PVT, as well as experimental information useful for the validation of new mathematical models of SRC-PVT. [ABSTRACT FROM AUTHOR]

The digitization of distribution power systems has revolutionized the way data are collected and analyzed. In this paper, the critical task of harnessing this information to identify irregularities and anomalies in electricity consumption is tackled. The focus is on detecting non-technical losses (NTLs) and energy theft within distribution networks. A comprehensive overview of the methodologies employed to uncover NTLs and energy theft is presented, leveraging measurements of electricity consumption. The most common scenarios and prevalent cases of anomalies and theft among consumers are identified. Additionally, statistical indicators tailored to specific anomalies are proposed. In this research paper, the practical implementation of numerous artificial intelligence (AI) algorithms, including the artificial neural network (ANN), ANFIS, autoencoder neural network, and K-mean clustering, is highlighted. These algorithms play a central role in our research, and our primary objective is to showcase their effectiveness in identifying NTLs. Real-world data sourced directly from distribution networks are utilized. Additionally, we carefully assess how well statistical methods work and compare them to AI techniques by testing them with real data. The artificial neural network (ANN) accurately identifies various consumer types, exhibiting a frequency error of 7.62%. In contrast, the K-means algorithm shows a slightly higher frequency error of 9.26%, while the adaptive neuro-fuzzy inference system (ANFIS) fails to detect the initial anomaly type, resulting in a frequency error of 11.11%. Our research suggests that AI can make finding irregularities in electricity consumption even more effective. This approach, especially when using data from smart meters, can help us discover problems and safeguard distribution networks. [ABSTRACT FROM AUTHOR]

This study thoroughly compares multiple single bidirectional and multiport converters (MPCs), highlighting the significant role of MPCs in multi-input and multi-output (MIMO) systems. MPCs offer a more efficient and cost-effective solution than multiple single converters, especially in applications involving photovoltaic (PV), electric vehicles (EVs) with storage systems, and power grids. This research emphasizes the importance of multi-input converters (MICs) in integrating diverse voltage sources. It notes the rising popularity of multi-output DC-DC converters in portable electronics, owing to their reduced component count, lower costs, and compact design. This paper emphasizes comparisons based on diverse aspects and applications, shedding light on recent developments in basic bidirectional converters. Additionally, it delves into the advancements in MPC topologies, focusing on efficiency, reliability, and modularity improvements. These advancements are crucial for harnessing cost reduction, simplicity, and compactness. Furthermore, this paper introduces an innovative multiport DC-DC converter tailored for integrating and managing renewable sources. This new converter design enhances PV system and battery storage performance by reducing power conversion steps, using fewer components, and improving voltage-boosting capabilities. Its unique bidirectional buck-boost structure allows for versatile connections between sources and loads with varying voltage and power requirements. The performance of this novel converter is evaluated through MATLAB/Simulink simulations under different scenarios. Experimental studies further validate its effectiveness, marking a significant contribution to power conversion and management in integrating renewable sources such as DC microgrids. [ABSTRACT FROM AUTHOR]

In order to fully utilize the control degrees of freedom of a multi-three-phase-star smooth-pole permanent magnet synchronous motor (PMSM), this paper first develops a modeling approach using a new matrix transformation method. The proposed transformation produces decoupled and independent star windings, removing the inductive couplings and preserving the model and torque control's consistency as the number of phases increases. The model, together with a new vector control scheme, is superior for studying the effect of the winding phase angle shift on motor performance. Based on a numerical simulation, this paper focuses on the quality analysis of phase currents, non-sequential currents, and torque ripple with different phase angles for double- and triple-star PMSM drives. The control of a triple-star PMSM is validated, and the behavior analysis is investigated by OPAL-RT. [ABSTRACT FROM AUTHOR]

Global warming, pollution, and increasing energy demand have compelled electrification of the transport sector. Electric vehicles are not only an attractive and cleaner mode of transport, but they also possess the capacity to offer flexible storage alternative based on bidirectional vehicle-to-grid schemes. Vehicle-to-grid or V2G technology permits electric vehicles' batteries to store energy and discharge it back to the power grid during peak-load periods. However, the feasibility and economic viability of V2G is still a matter of concern and needs investigation. In this paper, the authors delved into the feasibility of V2G technology by analysing the real time-charging data of a V2G demonstration project named EV-elocity, located at the University of Nottingham campus in the UK. The authors analysed the charging data and trip-status data of two charging sites and put forward some insights regarding the feasibility of V2G and the behavioural traits of the vehicles. This paper will enlighten the research community regarding the feasibility and benefits of V2G in a real-world environment by analysing the charging/discharging and vehicle behaviour and reporting the opportunities and benefits of vehicle-to-grid technology. [ABSTRACT FROM AUTHOR]

Due to the serious problems with energy efficiency, carbon emissions, and thermal comfort of rural residences in northern China, an optimization of active and passive heating technologies for rural residences is necessary. In this paper, an optimization for rural residences in northern China is conducted with four objectives: the whole life cycle carbon emission; the annual energy consumption through heating, ventilation, and air conditioning systems; the annual cost; and thermal comfort. In addition, the optimization model with active–passive heating technology synergy is resolved by NSGA-II genetic algorithm. The active and passive design variables, including the type of air source heat pump, orientation, the type and thickness of envelope insulation, the layer of window glass, the window-to-wall area ratio, as well as sunspace parameters are preferred to obtain the optimal solution. The results indicate that the optimal solution obtained by the ideal point method gives the most outstanding performance. Compared with the prototype, the optimized carbon emissions in severe cold and cold regions decreased by 56.1% and 54.6%, respectively. The annual energy consumption decreased by 59.7% and 62.2%. Finally, the roof insulation thickness is the most sensitive design variable in Pareto-optimal solution sets. This paper offers significant guidance in the application of the optimization method of active–passive technology synergy to the energy-saving design of buildings. [ABSTRACT FROM AUTHOR]

The paper presents some case spectral analysis of zero-sequence voltages and currents in an example industrial power distribution network. The network layout is based on typical power delivery networks in underground coal mines. Ground fault simulations have been made using an ATP/EMTP program. Due to the high environmental risks, the reliability of the protection relay operation related to their selectivity plays an important role. This paper tries to find the reasons for nonselective operation and unnecessary tripping in extensive mine cable networks, particularly with large power sources of higher-order harmonics. It was found that in transient states—due to the decaying oscillations occurring in complex RLC circuits—the results of short time measurements of the criterion values for ground fault protective relays can be overestimated (particularly for small values of ground resistance) and lead to nonselective tripping of a healthy cable line. Therefore, it might be advisable to increase the integration time used for measuring rms values. Also, if there is a significant level of higher harmonics in the industrial network generated by high-power converters, it should be noted that the higher harmonics of the ground fault current and currents measured by ground fault protection relays assume much higher values, which may also cause nonselective tripping. In this case, it may be advisable to use higher harmonic filters in the measuring circuits and to select a sufficiently high sampling frequency in the digital protective relays. [ABSTRACT FROM AUTHOR]

A new passivity-based voltage tracker for islanded Direct Current (DC) microgrids is presented in this paper. The proposed design develops a new sufficient condition for passivity-based state feedback with proportional and integral control using the attracting ellipsoid method. In this paper, we consider the time behavior of the extended vector, which completely describes the principle properties of the closed-loop system such as the boundedness of the trajectories within some ellipsoid and the dependence of its "size" on the feedback gains. The next step, which we are realizing in this paper, is the minimization of the attractive ellipsoid by selecting the "best" admissible feedback parameters. Here, it is important to note that the applied feedback is of PD-type (proportional differential) on the system state and I-type (integral) on the output. This is a new construction of the suggested feedback which gives several advantages for a designer. The suggested control is decentralized and uses only the local states; it is cost-effective and avoids the time delays in the communication networks which are needed if centralized control is used. The suggested control is carried out in the bilinear matrix inequality (BMI) framework. Extensive simulation is performed on a test system composed of renewable energy sources, under plug and play (PnP) operations, and uncertainties in distribution lines and loads. The performance of the proposed decentralized voltage controller is compared with that of a voltage tracker present in the literature. The comparison shows the improvements introduced by the proposed control ensure the stability of the dc bus voltage and a quick response under different scenarios of operating conditions. [ABSTRACT FROM AUTHOR]

Low or even zero carbon dioxide emissions will be an essential requirement for energy supplies in the near future. Besides transport and electricity generation, industry is another large carbon emitter. Hydrogen produced by renewable energy provides a flexible way of utilizing that energy. Hydrogen, as an energy carrier, could be stored in a large capacity compared to electricity. In Sweden, hydrogen will be used to replace coal for steel production. This paper discusses how the need for electricity to produce hydrogen will affect the electricity supply and power flow in the Swedish power grid, and whether it will result in increased emissions in other regions. Data of the Swedish system will be used to study the feasibility of implementing the hydrogen system from the power system viewpoint, and discuss the electricity price and emission issues caused by the hydrogen production in different scenarios. This paper concludes that the Swedish power grid is feasible for accommodating the additional electricity capacity requirement of producing green hydrogen for the steel industry. The obtained results could be references for decision makers, investors, and power system operators. [ABSTRACT FROM AUTHOR]

To study the microscopic thermal aging mechanism of insulating paper cellulose through molecular dynamics simulation, it is important to select suitable DP (Degree of Polymerization) and force field for the cellulose model to shorten the simulation time and obtain correct and objective simulation results. Here, the variation of the mechanical properties and solubility parameters of models with different polymerization degrees and force fields were analyzed. Numerous cellulose models with different polymerization degrees were constructed to determine the relative optimal force field from the perspectives of the similarity of the density of cellulose models in equilibrium to the actual cellulose density, and the volatility and repeatability of the mechanical properties of the models through the selection of a stable polymerization degree using the two force fields. The results showed that when the polymerization degree was more than or equal to 10, the mechanical properties and solubility of cellulose models with the COMPASS (Condensed-phase Optimized Molecular Potential for Atomistic Simulation Studies) and PCFF (Polymer Consistent Force Field) force fields were in steady states. The steady-state density of the cellulose model using the COMPASS force field was closer to the actual density of cellulose. Thus, the COMPASS force field is favorable for molecular dynamics simulation of amorphous cellulose. [ABSTRACT FROM AUTHOR]

Mineral oil is the most popular insulating liquid for high voltage transformers due to its function as a cooling liquid and an electrical insulator. Kraft paper has been widely used as transformer solid insulation for a long time already. The degradation process of transformer paper due to thermal aging in mineral oil can change the physical and chemical structure of the cellulose paper. Fourier transform infrared (FTIR) spectroscopy analysis was used to identify changes in the chemical structure of transformer paper aged in mineral oil. FTIR results show that the intensity of the peak absorbance of the O-H functional group decreased with aging but the intensity of the peak absorbance of the C-H and C=O functional groups increased with aging. Changes in the chemical structure of the cellulose paper during thermal aging in mineral oil can be analyzed by an oxidation process of the cellulose paper and the reaction process between the carboxylic acids in the mineral oil and the hydroxyl groups on the cellulose. The correlation between the functional groups and the average number of chain scissions of transformer paper gives initial information that the transformer paper performance can be identified by using a spectroscopic technique as a non-destructive diagnostic technique. [ABSTRACT FROM AUTHOR]

The main insulation system in high-voltage direct current (HVDC) transformer consists of oil-paper insulation. The formation of space charge in insulation paper is crucial for the dielectric strength. Unfortunately, space charge behavior changes because of the corrosive sulfur substance in oil. This paper presents the space charge behavior in insulation paper induced by copper sulfide generated by corrosive sulfur in insulation oil. Thermal aging tests of paper-wrapped copper strip called the pigtail model were conducted at 130 °C in laboratory. Scanning electron microscopy (SEM) was used to observe the surface of copper and paper. Pulse electroacoustic (PEA) and thermally stimulated current (TSC) methods were used to obtain the space charge behavior in paper. Results showed that both maximum and total amount of space charge increased for the insulation paper contaminated by semi-conductor chemical substance copper sulfide. The space charge decay rate of contaminated paper was significantly enhanced after the polarization voltage was removed. The TSC results revealed that copper sulfide increased the trap density and lowered the shallow trap energy levels. These results contributed to charge transportation by de-trapping and trapping processes. This improved charge transportation could be the main reason for the decreased breakdown voltage of paper insulation material. [ABSTRACT FROM AUTHOR]

The breakdown property of oil-impregnated paper is a key factor for converter transformer design and operation, but it is not well understood. In this paper, breakdown voltages of oil-impregnated paper were measured at different temperatures. The results showed that with the increase of temperature, electrical, electro-thermal and thermal breakdown occurred successively. An electro-thermal breakdown model was proposed based on the heat equilibrium and space charge transport, and negative differential mobility was introduced to the model. It was shown that carrier mobility determined whether it was electrical or thermal breakdown, and the model can effectively explain the temperature-dependent breakdown. [ABSTRACT FROM AUTHOR]

In this paper, polysiloxane is used to modify insulation paper cellulose, and molecular dynamics methods are used to evaluate the glass transition temperature and mechanical properties of the paper before and after the modification. Analysis of the static mechanical performance of the model shows that, with increasing temperature, the elastic modulus of both the modified and unmodified cellulose models decreases gradually. However, the elastic modulus of the modified model is greater than that of the unmodified model. Using the specific volume method and calculation of the mean square displacement of the models, the glass transition temperature of the modified cellulose model is found to be 48 K higher than that of the unmodified model. Finally, the changes in the mechanical properties and glass transition temperature of the model are analyzed by energy and free volume theory. The glass transition temperatures of the unmodified and modified cellulose models are approximately 400 K and 450 K, respectively. These results are consistent with the conclusions obtained from the specific volume method and the calculation of the mean square displacement. It can be concluded that the modification of insulation paper cellulose with polysiloxane will effectively improve its thermal stability. [ABSTRACT FROM AUTHOR]

Most power transformers operating in a power system possess oil-paper insulation. A serious defect of this type of insulation, which is associated with long operation time, is an increase in the moisture content. Moisture introduces a number of threats to proper operation of the transformer, e.g., ignition of partial discharges (PDs). Due to the varying temperature of the insulation system during the unit's normal operation, a dynamic change (migration of water) takes place, precipitating the oil-paper system from a state of hydrodynamic equilibrium. This causes the PDs to be variable in time, and they may intensify or extinguish. Studies on model objects have been conducted to determine the conditions (temperature, humidity, time) that will have an impact on the ignition and intensity of the observed phenomenon of PDs. The conclusions of this study will have a practical application in the evaluation of measurements conducted in the field, especially in relation to the registration of an online PD monitoring system. [ABSTRACT FROM AUTHOR]

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60–140 °C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies. [ABSTRACT FROM AUTHOR]

This paper studied the impact of moisture on the correlated characteristics of the condenser bushings oil-paper insulation system. The oil-impregnated paper samples underwent accelerated thermal aging at 130 °C after preparation at different initial moisture contents (1%, 3%, 5% and 7%). All the samples were extracted periodically for the measurement of the moisture content, the degree of polymerization (DP) and frequency domain dielectric spectroscopy (FDS). Next, the measurement results of samples were compared to the related research results of transformer oil-paper insulation, offering a theoretical basis of the parameter analysis. The obtained results show that the moisture fluctuation amplitude can reflect the different initial moisture contents of insulating paper and the mass ratio of oil and paper has little impact on the moisture content fluctuation pattern in oil-paper but has a great impact on moisture fluctuation amplitude; reduction of DP presents an accelerating trend with the increase of initial moisture content, and the aging rate of test samples is higher under low moisture content but lower under high moisture content compared to the insulation paper in transformers. Two obvious "deceleration zones" appeared in the dielectric spectrum with the decrease of frequency, and not only does the integral value of dielectric dissipation factor (tan δ) reflect the aging degree, but it reflects the moisture content in solid insulation. These types of research in this paper can be applied to evaluate the condition of humidified insulation and the aging state of solid insulation for condenser bushings. [ABSTRACT FROM AUTHOR]

To facilitate better interpretation of dielectric response measurements--thereby directing numerical evidence for condition assessments of oil-paper-insulated equipment in high-voltage alternating current (HVAC) transmission systems--a novel approach is presented to estimate the parameters in the extended Debye model (EDM) using wideband frequency domain spectroscopy (FDS). A syncretic algorithm that integrates a genetic algorithm (GA) and the Levenberg-Marquardt (L-M) algorithm is introduced in the present study to parameterize EDM using the FDS measurements of a real-life 126 kV oil-impregnated paper (OIP) bushing under different controlled temperatures. As for the uncertainty of the EDM structure due to variable branch quantity, Akaike's information criterion (AIC) is employed to determine the model orders. For verification, comparative analysis of FDS reconstruction and results of FDS transformation to polarization--depolarization current (PDC)/return voltage measurement (RVM) are presented. The comparison demonstrates good agreement between the measured and reconstructed spectroscopies of complex capacitance and tan δover the full tested frequency band (10-4 Hz-10³ Hz) with goodness of fit over 0.99. Deviations between the tested and modelled PDC/RVM from FDS are then discussed. Compared with the previous studies to parameterize the model using time domain dielectric responses, the proposed method solves the problematic matching between EDM and FDS especially in a wide frequency band, and therefore assures a basis for quantitative insulation condition assessment of OIP-insulated apparatus in energy systems. [ABSTRACT FROM AUTHOR]

It is now well-established that moisture in the oil paper insulation used in power and instrument transformers significantly reduces the transformers' lifetimes, and can eventually lead to premature failure. This moisture should, therefore, always be removed, not only during production but also after repairs. At the final stage of manufacturing, the drying process should be carried out to remove water and air vacuoles contained in the cellulose-based paper before impregnation. Successful drying helps increase the residual life of transformers, because the presence of moisture and air vacuoles accelerates the aging/degradation process of the oil paper insulation. Proper estimation of residual moisture before impregnation and the determination of the time required for drying play key roles in the time-consuming process of drying. In this paper, the disadvantages of inadequate drying are addressed, followed by a mathematical approach to model the paper drying process. A mathematical model describing the kinetics of drying according to temperature, initial moisture, paper weight, final moisture, and extraction rate is proposed. This model also estimated the amount of moisture removed at the end of the drying process. [ABSTRACT FROM AUTHOR]

Space charge has close relation with the trap distribution in the insulation material. The phenomenon of charges trapping and detrapping has attracted significant attention in recent years. Space charge and trap parameters are effective parameters for assessing the ageing condition of the insulation material qualitatively. In this paper, a new method for calculating trap distribution based on the double exponential fitting analysis of charge decay process and its application on characterizing the trap distribution of oil impregnated insulation paper was investigated. When compared with the common first order exponential fitting analysis method, the improved dual-level trap method could obtain the energy level range and density of both shallow traps and deep traps, simultaneously. Space charge decay process analysis of the insulation paper immersed with new oil and aged oil shows that the improved trap distribution calculation method can distinguish the physical defects and chemical defects. The trap density shows an increasing trend with the oil ageing, especially for the deep traps mainly related to chemical defects. The greater the energy could be filled by the traps, the larger amount of charges could be trapped, especially under higher electric field strength. The deep trap energy level and trap density could be used to characterize ageing. When one evaluates the ageing condition of oil-paper insulation using trap distribution parameters, the influence of oil performance should not be ignored. [ABSTRACT FROM AUTHOR]

Partial discharge (PD) behaviors of oil-paper insulation is distinctive in AC and DC combined electric fields in converter transformers from PD behaviors in pure AC or DC electric fields. The present study focuses on the PD developing processes and characteristics of oil-paper insulation systems with needle-plane defects under different AC/DC proportions. The degradation of oil-paper insulation can be accelerated by PD pulses incurred by needle-plane defects. AC-DC combined voltages are applied to the needle-plane defect model simultaneously in the established experimental platform, and the proportions of AC/DC voltages are decided according to the cases in actual converter transformers. The developing processes from the initiation of partial discharge until final breakdown were observed for each AC/DC proportion. PD parameters and patterns were acquired by a detector using the pulse current method. The test results indicate that the inception and breakdown voltages increase with the increase of the DC component in AC-DC combined voltages. However, pulse repetition rate and amplitude of PD shows a descending trend when AC/DC proportion decreases. Meanwhile, the PD recurrence rate in the phase between 180° and 360° becomes higher than that in the phase between 0° and 180° at the initial stage as the DC proportion increases; high-amplitude discharges mainly occur in the phase range between 180° and 360° when the pressboard is close to breakdown. The current study is useful in further research on fault diagnosis in converter transformers. [ABSTRACT FROM AUTHOR]

The condition of oil-paper insulation is closely related to the life expectancy of a transformer. The accurate results of oil-paper have not been obtained due to the impact of influencing factors. Therefore, in order to improve the evaluation accuracy of oil-paper insulation, in this paper, oil-paper samples which were prepared with different aging and moisture content were analyzed by frequency domain spectroscopy (FDS). Results show that when the moisture content is less than 2%, the range of 101∼103 Hz is mainly affected by moisture and aging has little effect. However, with the increase of moisture content, the effect of aging degree on this band became increasingly prominent. Sm, which represents the integral value from 10-1 to 10-3 Hz, and SDP, which represents the integral value from 101 to 103 Hz, were extracted as characteristic parameters of moisture content and aging degree respectively. Compensation factors γ which represents the influence ratio of moisture on SDP and Ø which represents the influence ratio of aging on Sm were introduced to compensate for the influence of moisture content and aging degree on characteristics respectively. Then, a new method was proposed to evaluate the condition of oil-paper based on compensation factors. Through this method, the influence in characteristics can be eliminated by the obtained actual compensation factors, thus distinguishing the internal influence between moisture content and aging degree on FDS. Finally, this method was verified by field test. [ABSTRACT FROM AUTHOR]

This article presents an algorithm for modelling an Adaptive Neuro Fuzzy Inference System (ANFIS) for power transformer paper conditions in order to estimate the transformer's expected life. The dielectric characteristics, dissolved gasses, and furfural of 108 running transformers were collected, which were divided into 76 training datasets and another 32 testing datasets. The degree of polymerization (DP) of the transformer paper was predicted using the ANFIS model based on using the dielectric characteristics and dissolved gases as input. These inputs were analyzed, and the best combination was selected, whereas CO + CO2, acidity, interfacial tension, and color were correlated with the paper's deterioration condition and were chosen as the input variables. The best combination of input variables and membership function was selected to build the optimal ANFIS model, which was then compared and evaluated. The proposed ANFIS model has 89.07% training accuracy and 85.75% testing accuracy and was applied to a transformer paper insulation assessment and an estimation of the expected life of four Indonesian transformers for which furfural data is unavailable. This proposed algorithm can be used as a furfural alternative for the general assessment of transformer paper conditions and the estimation of expected life and provides a helpful assistance for experts in transformer condition assessment. [ABSTRACT FROM AUTHOR]

Thermal stress and moisture absorption can cause a synergetic negative impact on kraft paper. Among various approaches for improving the dielectric properties of kraft paper, nanotechnology has had promising results. However, the hydrophilicity of most metal oxide nanoparticles renders nanomodified kraft paper more vulnerable to thermal stress and moisture, thereby inducing degradation. In nanomodified kraft paper research, the use of TiO2 nanoparticles has yielded the most promising results. The major shortfall, however, is the hydrophilicity of TiO2. This work investigated surface modifications of rutile-TiO2 nanoparticles (NPs) for improved hydrophobicity and thermal stability. Rutile-TiO2 NPs is a nontoxic metal oxide that can withstand high temperature and is stable in chemical reactions. Two cases of surfactants were used—alkyl ketene dimer (AKD) and alkenyl succinic anhydride (ASA). The intention was to increase heat resistance and reduce the surface free energy of the rutile-TiO2 NPs. The impacts of the surface modifiers on the rutile-TiO2 NPs were characterised using FT-IR, muffle furnace, analytical weight balance, and TGA. It was discovered that new functional groups were formed on the modified NPs examined through FT-IR spectra. This indicates new chemical bonds, introduced through the surface modification. The unmodified rutile-TiO2 NPs absorbed moisture, increasing their mass by 3.88%, compared with the modified nanoparticles, which released moisture instead. TGA analysis revealed that AKD- and ASA-modified rutile-TiO2 needed higher temperatures than the unmodified rutile-TiO2 to markedly decompose. AKD, however, gave better performance than ASA in that regard. As an example, those modified with 5% AKD sustained a 45% higher temperature than the pure TiO2 nanoparticles. Furthermore, in both cases of the surfactants, the higher the percent of surfactant content was, the more thermally stable the nanoparticles became. This work demonstrates the possibility of fabricating rutile-TiO2 NPs to give improved hydrophobicity and thermal stability for possible dielectric applications such as in kraft paper for power transformer insulation. [ABSTRACT FROM AUTHOR]

The accuracy of a predictive system is critical for predictive maintenance and to support the right decisions at the right times. Statistical models, such as ARIMA and SARIMA, are unable to describe the stochastic nature of the data. Neural networks, such as long short-term memory (LSTM) and the gated recurrent unit (GRU), are good predictors for univariate and multivariate data. The present paper describes a case study where the performances of long short-term memory and gated recurrent units are compared, based on different hyperparameters. In general, gated recurrent units exhibit better performance, based on a case study on pulp paper presses. The final result demonstrates that, to maximize the equipment availability, gated recurrent units, as demonstrated in the paper, are the best options. [ABSTRACT FROM AUTHOR]

Emerging global environmental pollution issues have caused a reduction in coal utilization, leading to an increased research focus on biomass use as an alternative. However, due to the low heat values of biomass, studies in this field are still in progress. Biomass primarily comprises cellulose, hemicellulose, and lignin. To determine the composition of these three components, the measurement methods recommended by TAPPI (Technical Association of the Pulp and Paper Industry) and NREL (National Renewable Energy Laboratory) are typically employed involving equipment such as HPLC. However, these methods are time consuming. In this study, we proposed a model for predicting cellulose, hemicellulose, and lignin contents based on elemental and industrial analyses. A dataset comprising 174 samples was used to develop this model. This was validated using 25 additional samples. The R2P values for cellulose, hemicellulose, and lignin were 0.6104–0.6362, 0.4803–0.5112, and 0.7247–0.7914, respectively; however, the R2CV values obtained from the validation results were 0.7387–0.7837, 0.3280–0.4004, and 0.7427–0.7757, respectively. The optimal models selected for cellulose, lignin, and hemicellulose were C1, L2, and 100-(C1-L2) or H2, respectively. Our predictions for woody and herbaceous biomass, including torrefied samples, should be applied with caution to other biomass types due to the potential accuracy limitations. To enhance the prediction accuracy, future research should broaden the range of biomass types considered and gather more data specifically related to woody and herbaceous biomass. [ABSTRACT FROM AUTHOR]

One of the possible causes of transformer failures is high moisture in the winding insulation system. In an extreme case, when the critical temperature is exceeded, a sudden release of water vapor from the transformer insulation, called the bubble effect, can occur. This article analyzes the initiation temperature of the bubble phenomenon in various solid insulation materials (Kraft cellulose paper and aramid-based high-temperature papers such as Nomex® 910 and Nomex® 926) immersed in two electro-insulating liquids (mineral oil and Midel 7131 synthetic ester). The initiation temperature of the bubble effect depends mainly on the moisture content of the solid insulation, but it was found to be slightly lower for high-temperature materials than for cellulose. However, after taking into account the differences related to uneven water absorption of the tested materials, the differences in the initiation temperature of individual solid materials are very small. Synthetic ester, compared to mineral oil, slightly increases the bubble initiation temperature, regardless of the solid material used. [ABSTRACT FROM AUTHOR]

The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference. [ABSTRACT FROM AUTHOR]

The resistivity of oil impregnated paper will decrease during its aging process. This paper takes paper resistivity as an assessment index to evaluate the insulation condition of oil impregnated paper in power transformer. The feasibility of this method are discussed in two aspects: reliability and sensitivity. Iterative inversion of paper resistivity was combined with finite element simulation. Both the bisection method and Newton's method were used as iterative methods. After the analysis and comparison, Newton's method was selected as the first option of paper resistivity iteration for its faster convergence. In order to consider the spatial distribution characteristic of paper aging and enhance the calculation accuracy, the resistivity calculation is expanded to a multivariate iteration based on Newton's method, in order to consider the spatial distribution characteristic of paper aging and improve the calculation accuracy. This paper presents an exploratory research on condition assessment of oil impregnated paper insulation, and provides some reference to the security and economy operation of power transformers. [ABSTRACT FROM AUTHOR]

Mining production, being one of the most energy-intensive industries globally, consumes substantial amounts of fossil fuels and contributes to extensive carbon emissions worldwide. The trend toward electrification and advanced developments in battery technology have shifted attention from diesel power to battery alternatives. These alternatives are appealing, as they contribute to decarbonisation efforts when compared to conventional diesel trucks. This paper presents a comprehensive review of recent technological advancements in powertrains for Mining Haulage Truck (MHT). It also compares these configurations based on mining system-level considerations to assess their future potential. The evaluated configurations include Diesel-Electric Truck (DET), Trolley Assist Truck (TAT), Battery-only Truck (BOT), Battery Trolley with Dynamic charging truck (BT-D), and Battery Trolley with Stationary charging truck (BT-S). According to the analysis, the energy demand for on-board diesel or battery power (excluding trolley power) in these alternative options is as follows: DET—681 kWh, BOT—645 kWh, TAT—511 kWh, BT-S—471 kWh, and BT-D—466 kWh. The paper also illustrates the theory of battery size design based on the current battery technology, battery material selection, battery package design, and battery size selection methods. In the case of tailored battery size selection, BOT, BT-D, and BT-S configurations require LiFePO4 (LFP) battery masses of 25 tonnes, 18 tonnes, and 18 tonnes, respectively. Based on a techno-economic assessment of battery MHT alternatives with a future perspective, it has been determined that BT-D requires the lowest amount of on-board battery energy. Furthermore, over a span of 20 years, BT-S has demonstrated the lowest on-board battery cost. [ABSTRACT FROM AUTHOR]

Access to clean energy remains a major issue in developing countries, particularly Sub-Saharan Africa, despite successive policies and the assistance of international institutions or organizations. The United Nations (UN) launched some of the most ambitious initiatives with the Millennium Development Goals and, more recently, the Sustainable Development Goals and Power Africa, a United States (US) government initiative. Sub-Saharan Africa has an important potential in renewable energy for both biogas and solar photovoltaic energy, but they remain underexploited. This paper presents the challenges of access to clean energy in developing countries and the failure of remedial policies mostly based on public–private partnerships (PPPs) in the context of endemic poverty of rural populations. In addition, the development of modern energy technologies remains very limited. Appropriate reforms should be carried out to change the paradigm and allow universal access to clean energy. This paper also addresses the different structural barriers that hinder access to technology in Sub-Saharan Africa and the consequences of access to clean energy in the context of poverty. [ABSTRACT FROM AUTHOR]

The paper presents an adaptation of the microinverter platform from Texas Instruments to incorporate a battery energy storage system (BESS) alongside the development of the BESS system itself. Initially designed for unidirectional power flow between PV panels and an electric grid, the platform required modifications to accommodate bidirectional energy transfer for BESS integration. These modifications encompass software adjustments and hardware enhancements, which are all detailed within the paper. The electrical configuration includes selecting and deploying components such as DCDC power converters, microcontrollers, measured signals, and actuating signals to facilitate battery connection to the platform's DC bus. Furthermore, a supervisory control and data acquisition (SCADA) system is devised for supervisory control and monitoring, with its implementation outlined. Control software tailored for the chosen microcontroller of the DCDC converters is described in terms of structure and functionality. A hardware-in-the-loop (HIL) methodology is employed to validate the proposed modifications and microgrid configuration. Utilizing the real-time simulator OPAL-RT, the paper presents experimental results and their analysis within the considered microgrid environment. [ABSTRACT FROM AUTHOR]

The emerging energy transition is particularly described as a move towards a cleaner, lower-carbon system. In the context of the global shift towards sustainable energy sources, this paper reviews the potential and roadmap for hydrogen energy as a crucial component of the clean energy landscape. The primary objective is to present a comprehensive literature overview, illuminating key themes, trends, and research gaps in the scientific discourse concerning hydrogen production and energy policy. This review focuses particularly on specified geographic contexts, with an emphasis on understanding the unique energy policies related to renewable energy in Brazil, Austria, and Germany. Given their distinct social systems and developmental stages, this paper aims to delineate the nuanced approaches these countries adopt in their pursuit of renewable energy and the integration of hydrogen within their energy frameworks. Brazil exhibits vast renewable energy potential, particularly in wind and solar energy sectors, positioning itself for substantial growth in the coming years. Germany showcases a regulatory framework that promotes innovation and technological expansion, reflecting its highly developed social system and commitment to transitioning away from fossil fuels. Austria demonstrates dedication to decarbonization, particularly through the exploration of biomethane for residential heating and cooling. [ABSTRACT FROM AUTHOR]

Due to environmental concerns, natural refrigerants and their use in refrigeration and air conditioning systems are receiving more attention from manufacturers, end users and the scientific community. The study of heat transfer and pressure drop is essential for accurate design and more energy efficient cycles using natural refrigerants. The aim of this work is to provide an overview of the latest outcomes related to heat transfer and pressure drop correlations for ammonia, propane, isobutane and propylene and to investigate the current state of the art in terms of operating conditions. Available data on the existing correlations between heat transfer coefficients and pressure drops for natural refrigerants have been collected through a systematic search. Whenever possible, validity intervals are given for each correlation, and the error is quantified. It is the intention of the authors that this paper be a valuable support for researchers and an aid to design, with particular reference to heat pumps. A procedure based on the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) statement was adopted, and the Scopus database was used to query the relevant literature. A total of 135 publications qualified for inclusion in the survey; 34 articles report experimental investigations for unusual geometric conditions. Of the 101 selected papers related to usual geometric conditions, N = 50 deal only with HTC, N = 16 deal only with pressure drop and the remainder (N = 35) analyse both HTC and pressure drop. Among the 85 HTC papers, N = 53 deal with the evaporating condition, N = 30 with condensation and only N = 2 with the heat transfer correlations under both conditions. Most of the 101 articles concern propane and isobutane. The high temperatures are less widely investigated. [ABSTRACT FROM AUTHOR]

Due to concerns with air pollution and climate change, governments and transport operators around the world have engaged in transforming their fossil-fueled vehicles into electric vehicles (EVs). It is essential to build a model for the electrifying process to minimize the operation costs. This paper presents a systematic analytical approach for the electrification of a fire ambulance service station. This approach begins with the selection of suitable EVs to replace the current service vehicles. Subsequently, an in-depth analysis is conducted to determine the practical utilization of EVs at the station. The model proposes two charging strategies: immediate charging upon an EVs' return and smart charging. Based on the chosen EVs and charging strategies, a comprehensive assessment of the load profiles for the planned EV charging station is performed. In accordance with the load profiles, a mathematical model to minimize the infrastructure and operation costs of the charging station is proposed. Various pricing schemes are compared to identify the most efficient pricing scheme for the charging station, and economic analyses of the EVs and traditional ambulance vehicles are proposed in this paper. The test results indicate that the progressive pricing scheme is well suited for immediate charging strategies, whereas smart charging should opt for the time-of-use pricing scheme. Selecting the appropriate pricing scheme has the potential to significantly reduce electric energy costs. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive study on the impacts of peer-to-peer (P2P) energy markets on distribution systems, specifically focusing on voltage, power loss, and congestion. While P2P energy markets create opportunities for direct trading between prosumers and consumers, ensuring compliance with distribution system constraints remains a challenge. This paper proposes an iterative method and graphical interpretation in order to assess complex interactions, addressing the persistent issue of network constraints. Additionally, this paper proposes a method to determine distribution locational marginal prices (DLMPs) for real-time traditional energy markets. This ensures effective coordination among sellers, buyers, and the distribution system operator. The proposed method aims to prevent negative impacts on distribution system operation via the determination of the allowable maximum trading power (MTP), ensuring empirical validity and practical implementation via operating conditions and forecast errors, thus distinguishing it from prior studies. This paper also establishes a model for P2P energy market interactions, utilizing linear estimations for efficient DLMP updates. The contributions of this paper enhance the understanding and operation of P2P energy markets, and is supported by simulation results validating the proposed method. [ABSTRACT FROM AUTHOR]

This paper introduces a groundbreaking approach to demand response management, aiming to empower consumers through innovative strategies. The key contribution is the concept of "acquiring flexibility rights", wherein consumers engage with power aggregators to curtail energy usage during peak-load periods, receiving incentives in return. A flexibility right coefficient is introduced, allowing consumers to tailor their participation in demand response programs, ensuring their well-being. Additionally, a lighting intensity control system is developed to enhance residential lighting network efficiency. The study demonstrates that high-energy consumers, adopting a satisfaction factor of 10, can achieve over 61% in electricity cost savings by combining the lighting control system and active participation in demand response programs. This not only reduces expenses but also generates income through the sale of flexibility rights. Conversely, low-energy consumers can fully offset their expenses and accumulate over USD 33 in earnings through the installation of solar panels. This paper formulates an optimization problem considering flexibility rights, lighting control, and time-of-use tariff rates. An algorithm is proposed for a distributed solution, and a sensitivity analysis is conducted for evaluation. The proposed method showcases significant benefits, including cost savings and income generation for consumers, while contributing to grid stability and reduced blackout occurrences. Real data from a residential district in Tehran validates the method's effectiveness. This study concludes that this approach holds promise for demand response management in smart grids, emphasizing the importance of consumer empowerment and sustainable energy practices. [ABSTRACT FROM AUTHOR]

There is limited research focused on achieving optimal torque control performance of Switched Reluctance Generators (SRGs). The majority of existing studies tend to favor voltage or power control strategies. However, a significant drawback of SRGs is their susceptibility to high torque ripple. In power generation systems, torque ripple implicates fluctuations in the generated power of the generator. Moreover, high torque ripple can lead to mechanical vibrations and noise in the powertrain, impacting the overall system performance. In this paper, a Torque Sharing Function (TSF) with Indirect Instantaneous Torque Control (IITC) for SRG applied to Wind Energy Conversion Systems (WECS) is proposed to minimize torque ripple. The proposed method adjusts the shared reference torque function between the phases based on instantaneous torque, rather than the existing TSF methods formulated with a mathematical expression. Additionally, this paper introduces an innovative speed control scheme for SRG drive using a Fuzzy Super-Twisting Sliding Mode Command (FSTSMC) method. Notably robust against parameter uncertainties and payload disturbances, the proposed scheme ensures finite-time convergence even in the presence of external disturbances, while effectively reducing chattering. To assess the effectiveness of the proposed methods, comprehensive comparisons are made with traditional control techniques, including Proportional–Integral (PI), Integral Sliding Mode Control (ISMC), and Super-Twisting Sliding Mode Control (STSMC). The simulation results, obtained using MATLAB®/SIMULINK® under various speeds and mechanical torque conditions, demonstrate the superior performance and robustness of the proposed approaches. This study presents a thorough experimental analysis of a 250 W four-phase 8/6 SRG. The generator was connected to a DC resistive load, and the analysis focuses on assessing its performance and operational characteristics across different rotational speeds. The primary objective is to validate and confirm the efficacy of the SRG under varying conditions. [ABSTRACT FROM AUTHOR]

In city-integrated energy systems containing electric–thermal multi-energy sources, the uncertainty of renewable energy sources and the fluctuation of loads challenge the safe, efficient, economic and stable operation of the integrated energy systems. This paper introduces a novel approach for the operation of a carbon capture plant/CHP with PV accommodation within a city-integrated energy system. The proposed strategy aims to maximize the utilization of photovoltaic (PV) power generation and carbon capture equipment, addressing issues related to small-scale CHP climbing constraints and short-term output regulation. Additionally, this paper presents a multi-timescale optimal scheduling strategy, which effectively addresses deviations caused by PV fluctuations and load changes. This was achieved through a detailed analysis of the CHP climbing constraints, carbon capture equipment operation and real-time characteristics of PV power generation. This paper introduces a fully distributed neural dynamics-based optimization algorithm designed to address multi-timescale optimization challenges. Utilizing rolling cycles, this algorithm computes both day-ahead and real-time scheduling outcomes for urban integrated energy systems. Theoretical analyses and numerical simulations were conducted to validate the precision and efficacy of the proposed model and algorithm. These analyses quantitatively evaluate the scheduling performance of PV power generation and carbon capture CHP systems across various timescales. [ABSTRACT FROM AUTHOR]

The phase circulating current (PCC) of the parallel three-phase inverter systems dramatically affects the power quality and conversion efficiency of the power grid. In this paper, a composite suppression strategy is proposed to solve the PCC issue by using the sliding mode control (SMC) approach and improved virtual impedance droop control. Taking the commonly used 2-group parallel three-phase inverter as an example, an inter- and intra-classification model is established by analyzing the sources of PCC. In order to suppress the inter-PCC, the traditional virtual impedance droop control is given, following the improved substitute by combining SMC. And the variables of the bus voltage, Q-U loop, P-f loop, and the virtual-induced reactance are also introduced for the robust control of the impedance droop. On the other side, a SMC-based suppression approach is designed to solve the issue of the intra-PCC. Its idea is to introduce a regulation factor for the space vector pulse width modulation (SVPWM) so that the zero-sequence voltage can be eliminated and the influence of the intra-PCC can be relieved. Comparative simulations and experiments validate the effectiveness of the methods proposed in this paper. [ABSTRACT FROM AUTHOR]

This paper proposes a switched capacitor-based soft-switching proportional dimming LED driver to address color-mixing LED applications. The driver utilizes a half-bridge switch structure and incorporates a switched capacitor to regulate the dual resonant network. This configuration facilitates current sharing across each resonant network and enables fixed proportion dimming between them. The common inductance leveraged in this design results in fewer switching devices, thereby enhancing efficiency. Furthermore, all switches and diodes achieve soft switching, contributing to high efficiency. Finally, this paper built a 19 W experimental prototype, and the maximum efficiency reached 95.56%, which verified the correctness and feasibility of the driver. [ABSTRACT FROM AUTHOR]

With the increasing penetration of renewable energy resources, their variable, intermittent and unpredictable characteristics bring new challenges to the power system. These challenges require micro-meteorological data and techniques to provide more support for the power systems, including planning, dispatching, operation, and so on. This paper aims to provide readers with insights into the effects of micro-meteorology on power systems, as well as the actual improvement brought by micro-meteorology in some power system scenarios. This paper provides a review including the relevant micro-meteorological techniques such as observation, assimilation and numerical techniques, as well as artificial intelligence, presenting a relatively complete overview of the most recent and relevant micro-meteorology-related literature associated with power systems. The impact of micro-meteorology on power systems is analyzed in six different forms of power generation and three typical scenarios of different stages in the power system, as well as integrated energy systems and disaster prevention and reduction. Finally, a case study in China is provided. This case takes wind power prediction as an example in a power system to compare the performance when applying micro-meteorological data or not. The experimental results demonstrated that using the micro-meteorological reanalysis dataset with high spatial--temporal resolution for wind power prediction performed better, verifying the improvement of micro-meteorology to the power system to some extent. [ABSTRACT FROM AUTHOR]

Ever-increasing penetration of distributed energy resources (DERs) in the power grids, alongside their numerous benefits, brings new challenges that call for enhanced solutions in the field of control and management of power grids. The majority of the available research have considered either distribution or transmission grids in their studies. In this paper, a comprehensive review of the effects of DERs on the distribution and transmission grids is performed. The focus of this paper is on hierarchical management methods in order to categorize different approaches and highlight the gaps. Moreover, a review is conducted in the field of the newly introduced distributed energy resources management system (DERMS) concept. A DERMS can facilitate the hierarchical energy management procedure due to its functionalities and broad capabilities. Hence, its implementation in energy management and its impact on the power grid will be assessed with the aid of a co-simulation platform that considers both transmission and distribution grids. [ABSTRACT FROM AUTHOR]

In the European Union, increasing attention is already being paid not only to the development of renewable energy sources, but also to the establishment of solutions to achieve local energy self-sufficiency while increasing the role of citizens in managing the energy they generate. This approach is expected both to have a positive impact on the environment and the reduction of greenhouse gas emissions, and to enhance energy security—both in economic and civic terms by, i.a., combating energy poverty. The development of local energy communities promoted in the EU is supported i.a. by energy cooperatives. These contribute to the efficient harnessing of renewable energy potential in rural and urban-rural areas, and have been developing in Poland for several years now. In their previous studies, the authors of this research paper attempted to verify the generation (number, type and capacity of installed sources) and consumption (energy demand) configurations in which an energy cooperative would be a viable solution for prosumers who might establish it. However, over the past few years, the conditions for prosumers and the method of their accounting with the electricity seller have changed radically in Poland (shift from net metering to net billing). This situation has opened up space for further research and encouraged the authors to revisit the problem of analyzing the viability of establishing energy cooperatives in relation to the rules of operation of individual prosumers. This research was carried out for three scenarios, and the horizon of the analyses conducted and described extends to 2045. The comparative analysis included energy consumers without their own generation sources, prosumers with a photovoltaic generation installation covered by the net billing model, as well as a scenario involving prosumers' cooperation within an energy cooperative, which by law is settled in the net metering model. Conclusions from the research and simulations made it possible to confirm the claim that, despite changes in the rules of prosumer billing, developing energy independence in the energy community formula results in a significant reduction in the cost of purchasing electricity (even several times lower purchase costs in the timeframe analyzed) and can lead to a reduction in the payback time of investments in generation sources even by a factor of two. The results presented in this research paper open up space for further research. The outcomes allow us to assume that energy cooperatives—in the organizational and institutional model in Poland—are a good tool for reducing the phenomenon of energy poverty on a local scale. [ABSTRACT FROM AUTHOR]

Numerical and experimental studies were conducted to study the nonlinear phenomena of a 1000 MW ultra-supercritical four-corner tangential pulverized coal boiler. In this paper, (1) a 3D model of a furnace with a symmetrical structure was established to analyze the asymmetric flow phenomenon and multi-solution phenomenon of flow for multiple timepoints under the same boundary conditions. (2) The visual experiment verified that the flow in the furnace also behaved asymmetrically. (3) On the basis of correctly predicting the nonlinear law, the "diagonal start up" method and the "sequential start up" method are proposed. (4) An uneven coefficient of velocity distribution M, deviation coefficient of flue gas mass flow rate Eq and gas temperature deviation coefficient ET are proposed to quantitatively analyze the degree to which the actual tangent circle deviates from the ideal tangent circle. The tangent circle under the "sequential start up" method is the closest to the ideal, which can reduce the thermal deviation of the furnace outlet from 67 K under the "simultaneous start up" method to 41 K. In this paper, the initial steady-state flow field in the furnace is established by using the initial value sensitivity of the nonlinear system through different burner-opening methods, so as to reduce the thermal deviation at the furnace outlet and achieve the purpose of accurate control. [ABSTRACT FROM AUTHOR]