Search

The sustainable use of natural resources is becoming an increasingly important issue today. Stone paper, produced as an alternative to cellulose-based paper from the forest, is rich in minerals and produced without cellulose and water. This study focuses on the behavior of screen-printing ink on two different papers, stone paper and coated sticker paper. Properties such as ink adhesion, rubbing resistance, optical printing ink density, ink consumption, and lightfastness were measured on these surfaces. Solvent- and UV-based inks were used, and printing was carried out on cellulose-based (coated sticker paper) and mineral-based (stone paper) paper layers using three different mesh counts (90, 120, and 140 tpc). The rubbing resistance and lightfastness of the papers were also measured. The present findings revealed that stone paper had the same printability properties as cellulose-based paper. The study concluded that using a 140 tpc mesh with both types of ink results in a high-lightfastness ink layer and lower ink consumption. UV-based inks exhibited high rub resistance across all mesh counts. Additionally, when printing with stone paper, there will be a reduction in ink consumption, thereby achieving cost savings. Based on the present findings, it was concluded that water- and oil-resistant stone paper can be considered an essential alternative in many fields, including the printing industry.

This study investigates the physical, mechanical, and structural characteristics of handmade paper samples derived from cellulose extracted from grass clippings using two distinct methods as follows: (1) alkali treatment and (2) alkali treatment followed by bleaching, coupled with the incorporation of barium sulfate as a mineral filler. Our investigation revealed that the handmade paper samples’ densities, moisture contents, and thicknesses varied within the ranges of 0.436 to 0.549 g/cm3, 5.60 to 2.51%, and 0.41 to 0.50 mm, respectively. The tensile strength and folding endurance of the papers produced through alkali treatment with barium sulfate were notably superior to those produced from bleached pulp and barium sulfate. Our analysis indicates that several critical factors, including paper density, thickness, the crystallinity index, and the microfibrillar structure of cellulose, intricately influence the mechanical and strength properties of the samples. Using Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) techniques, we identified characteristic cellulose bonds and examined cellulose’s crystalline and amorphous phases. Additionally, the crystallinity index of the samples was determined using both the Segal and peak deconvolution methods. Scanning electron microscopy (SEM) micrographs revealed interconnected networks of cellulose fibers with varying thicknesses and lengths, along with incorporated mineral filler within the cellulose fiber structure. Variations in mineral particle retention were attributed to the presence or absence of cellulose microfibrils. These findings contribute to our understanding of the observed strength characteristics of the paper samples and underscore the potential applications of cellulose derived from grass clippings, especially when combined with barium sulfate as a mineral filler in paper production.

The research results and evaluation of the applicability of the original composition of hybrid paper based on silver nanowires (AgNWs), cellulose pulp (CP), and carbon nanotubes (CNTs) are presented and discussed. The material tested was used to manufacture sensors for mechanical deformation resulting from external influences or related to human activity interactions. The sensors were fabricated using an AgNWs + CP suspension and additives by the vacuum filtration method. The substrate obtained was machined and then laminated with a layer of poly(dimethylsiloxane) (PDMS). The recorded responses to selected types of imposed mechanical interactions in the form of changes in the relative resistance of the sensor throughout the tests showed a close cause-and-effect relationship. The response of the tested systems when applying an alternating magnetic field was also observed. The results indicate that the proposed solutions can find application in the monitoring of mechanical interactions resulting from the dynamic behavior of physical objects, as well as derived from selected human vital functions.

This paper addresses the challenges of data sparsity and personalization limitations inherent in current recommendation systems when processing extensive academic paper datasets. To overcome these issues, the present work introduces an innovative recommendation model that integrates the wealth of structured information from knowledge graphs and refines the amalgamation of temporal and relational data. By applying attention mechanisms and neural network technologies, the model thoroughly explores the text characteristics of papers and the evolving patterns of user behaviors. Additionally, the model elevates the accuracy and personalization of recommendations by meticulously examining citation patterns among papers and the networks of author collaboration. The experimental findings show that the present model surpasses baseline models on all evaluation metrics, thereby enhancing the precision and personalization of academic paper recommendations.

Environmental pollution is a significant problem and is increasing gradually as more and more harmful pollutants are being released into water bodies and the environment. Water pollutants are dangerous and pose a threat to all living organisms and the ecosystem. Paper waste is one of the most widespread and largest wastes in the world. This research aims to address two important problems simultaneously: the reduction in solid waste in the environment using activated carbon from paper waste as potential adsorbents and the removal of harmful contaminants from water. Carbon from paper waste was activated with H2O2, HNO3, and KMnO4 for the adsorption of Cr(VI) and MB. SEM, EDX, FTIR, Raman, and BET were used to determine the properties of the materials. The surface morphology of the materials consisted of amorphous particles. EDX shows that all activated samples have a higher content of (O) than carbon paper waste. Adsorption studies showed that there was a stronger interaction between the pollutants and the adsorbent at a higher initial concentration (200 mg/L) than at the lower initial concentrations. The contact time data show that uptake increases when the interaction time between the contaminant and the adsorbent is increased. The tests for the pH of the solution show that the adsorption of Cr(VI) decreases when the pH is gradually increased, whereas the adsorption of MB increases when the pH of the solution is increased. The results fit better with the Freundlich isotherm and PSO models. The temperature studies show that the enthalpy was positive, indicating that the uptake process is endothermic. The Gibbs free energy values were all negative, indicating that adsorption between the adsorbents and the pollutants was favored. After four consecutive cycles, all the samples retained more than 60% of their uptake capability.

Invasive alien plant species (IAPS) may cause threats to native biodiversity in ecosystems. Researchers have been investigating all the possible ways that they can be used effectively for other purposes. Since IAPS are capable of forming cellulose fibre nets, in this research, papers were made from three different types of IAPS (Japanese knotweed, giant goldenrod, and black locust). This research examined these IAPS papers and their effectiveness when used as printing substrates. In comparison to commercial office paper, the differences in basic, surface, optical, and microscopic properties were measured. As a widely used technology, inkjet printing was applied. We tested a commonly used sans-serif typeface (which has been established as being more legible than other typefaces in previous research) in three different type sizes (i.e., 8, 10, and 12 pt). According to the results, paper made from IAPS could offer some usable properties and acceptable legibility, especially when printing typefaces with specific attributes, such as moderate counter size, higher x-height, and minimal differences in the letter stroke width, are used. An appropriate typographic tonal density should be achieved in combination with an adequate letter size, e.g., 10 pt type size when a sans-serif typeface is used.

This review explores circular economy principles in regard to ethanol production from paper-mill sludge. Environmental sustainability and renewability over fossil fuels make second generation ethanol an attractive energy source in a rapidly growing population and consumption world. Paper sludge (PS), a by-product of the pulp and paper (P&P) industry, can no longer be recycled for paper production and is mainly disposed of in landfills. Therefore, it poses a major environmental challenge. However, it has shown potential as a valuable raw material for ethanol production, along with other pulp and paper products, due to its abundant availability and high cellulosic content. This waste-to-energy (WtE) technology for ethanol production is proposed as an alternative, aligning with circular economy concepts to maximize resource efficiency and minimize waste. This review underlines the circular economy aspects of bioethanol production within paper mill sludge management systems. Circular economy principles applied to ethanol production from PS offer a promising avenue for sustainable biofuel development that not only addresses waste management challenges but also enhances the overall environmental performance of biofuel production. Furthermore, economic benefits are described, highlighting the potential for job creation and community development.

Inflammable building finishing materials act as a major cause of fire propagation, and they, therefore, pose significant risks to life and can lead to property damage. To replace such flammable building finishing materials, many countries have established regulations limiting their use, which has led to extensive research on the development of flame-retardant building finishing materials. Such methods have included adding flame retardants to construction materials to reduce the heat release rate and total heat release. The present study aimed to enhance the fire performance of cellulose-based architectural finishing materials by creating a dual flame-retardant mixture using expandable graphite and magnesium hydroxide added to recycled paper waste. Specimen fabrication involves using a pressing method to apply uniform pressure to compress the mixture in a mold. The total heat release (THR), CO, and CO2 production of the produced specimens were measured using a cone calorimeter while varying the magnesium hydroxide additive ratio. The combustion gases were measured through NES 713 experiments to determine any changes in the Toxic Index corresponding to variations in the magnesium hydroxide content. The experiment results established a correlation between the magnesium hydroxide additive ratio and the total heat release, as well as the existence of variations in CO and CO2 production for the dual flame-retardant recycled paper material. A database for combustion gases was also obtained. It was confirmed that the fire performance was improved by confirming that the total heat release decreased by 52% from the previous one in the magnesium hydroxide content of 30 g, and it was confirmed that the inflection points of the Toxic Index value due to the change in CO and CO2 gas production occurred in the magnesium hydroxide content of 20 g due to the improvement of the fire performance. Through the ISO 5660-1 experiment data, we have secured data that can be used as foundational information for performance-oriented fire risk assessments, thereby ensuring the fire safety of cellulose materials that are vulnerable to fire.

In recent years, due to environmental awareness regarding the harmfulness of polymeric materials, there has been a growing interest in using papers, especially those from alternative raw materials. The importance of using all available raw materials is imperative today. Raw materials that were once viewed as waste are now of great importance because they have the ability to replace raw materials that are used irrationally or are lacking. Cereal straw is a lignocellulosic material that could be used in the paper industry and in the production of increasingly prevalent paper packaging. The aim of this research was to analyze the relationships between the qualitative parameters of straw-based printed papers containing 30% agricultural residues (wheat, barley, or triticale). The influence of two qualitative parameters (ink penetration depth and optical ink density) on the print-through was observed using multiple regression analysis on straw-based papers produced at the laboratory level. Throughout the research, 100% recycled wood paper was used as a reference sample. The results of the regression analysis showed that none of the variables individually make a statistically significant contribution to the prediction of the dependent variable in a linear context, that is, they indicate a non-linear interaction between the variables and the specific conditions under which the dependent variable reaches local extremes and changes in the gradient. Considering the results of the regression analysis and the visualization of the relationship, the model was additionally tested with other independent variables (paper type). From the results obtained, it can be concluded that the alternative straw-based paper with 30% barley pulp has the best interaction between ink and paper, which is the most similar to the reference sample in terms of printability, while the alternative straw-based paper with 30% wheat generally differs significantly from the reference paper when all three prints are considered.

The valorization of wastes as an alternative or secondary raw material in various products and processes has been a solution for the implementation of sustainability, a safer environment, and the concept of circular economy in the efficient use and management of natural resources. To promote sustainability through a circular economy approach, this work tries to demonstrate the environmental gains that are obtained by bringing together, in an industrial symbiosis action, two large industrial sectors (the pulp and paper and the road pavement sectors) responsible for generating large amounts of wastes. A sustainability assessment, based on a life cycle and circular economy approach, is presented here, and discussed using a simple case study carried out on a real scale. Two wastes (dregs and grits) from the pulp and paper industry (PPI) were used to partially replace natural fine aggregates in the production of bituminous mixtures used on the top surface of road pavements. The impacts at a technical, environmental, economic, and social level were assessed and it was shown that this simple waste valorization action is not only positive for the final product from a technical point of view, but also for the environment, causing positive impacts on the different sustainability dimensions that were evaluated.

The academic community has witnessed a notable increase in paper publications, whereby the rapid pace at which modern society seeks information underscores the critical need for literature mapping. This study introduces an innovative automatic model for categorizing articles by subject matter using Machine Learning (ML) algorithms for classification and category labeling, alongside a proposed ranking method called SSS (Scientific Significance Score) and using Z-score to select the finest papers. This paper’s use case concerns industry productivity. The key findings include the following: (1) The Decision Tree model demonstrated superior performance with an accuracy rate of 75% in classifying articles within the productivity and industry theme. (2) Through a ranking methodology based on citation count and publication date, it identified the finest papers. (3) Recent publications with higher citation counts achieved better scores. (4) The model’s sensitivity to outliers underscores the importance of addressing database imbalances, necessitating caution during training by excluding biased categories. These findings not only advance the utilization of ML models for paper classification but also lay a foundation for further research into productivity within the industry, exploring themes such as artificial intelligence, efficiency, industry 4.0, innovation, and sustainability.

Expansive soil exhibits significant swellings and shrinkages, which may result in severe damage or the collapse of structures built upon it. Calcium-based admixtures, such as lime, are commonly used to improve this problematic soil. However, traditional chemical additions can increase significant environmental stress. This paper proposes a sustainable solution, namely, the use of lignin fiber (LF) from the paper industry to partially replace lime as an amendment for expansive soils. Both the macroscopic and microscopic characteristics of the lignin fiber-treated expansive soil are extensively studied. The results show that the mechanical properties of expansive soil are improved by using lignin fiber alone. Under the condition of an optimal dosage of 8%, the compressive strength of lignin fiber-modified soil can reach 193 kPa, the shear strength is increased by 40% compared with the untreated soil, and the water conductivity is also improved with the increase in dosage. In addition, compared with 2% lime-modified soil, the compressive strength of 8% lignin fiber- and 2% lime composite-treated expansive soil increased by 50%, the cohesion increased by 12%, and the water conductivity decreased significantly. The microstructure analysis shows that at an 8% lignin fiber content, lignin fibers interweave into a network in the soil, which effectively enhances the strength and stability of the improved soil. Simultaneously, the fibers can form bridges across the adjacent micropores, leading to the merging of pores and transforming fine, dispersed micropores into larger, connected macropores. Lime promotes the flocculation of soil particles, forming larger aggregates and thus resulting in larger pores. The addition of fibers exerts an inhibitory effect on the flocculation reaction in the composite-improved soil. In conclusion, lignin fibers are an effective addition used to partially replace calcium admixture for the treatment of expansive soil, which provides a sustainable and environmentally friendly treatment scheme for reducing industrial waste.

This study evaluated the impact of soil modifiers on seed germination and soil quality. Mixtures of paper mill sludge (PMS) with camellia oilseed cake (CO) and peat moss (P), as well as with oilseed cake of toothache tree (TO) and peat moss (P), showed promising results as biostimulants for seed germination. The addition of PMS increased the germination index, indicating its beneficial effects on seed performance. The pH levels remained optimal, and the electrical conductivity values stayed within acceptable ranges, suggesting minimal hindrance to plant growth. The cation exchange capacity increased with PMS, enhancing nutrient availability. Composted mixtures exhibited increased phosphorus levels, contributing to soil fertility. While the organic matter content decreased after composting, the carbon-to-nitrogen ratio remained balanced. The bulk density increased after composting, potentially improving soil drainage. Overall, the TO-containing mixture demonstrated superior growth rates compared to the P. These findings support the use of PMS-based soil modifiers for enhancing seed germination and improving soil quality.

The study and advancement of crank-slide actuating mechanisms based on four-link structural groups are promising for the development of new designs of crank presses and other stamping and forging machines [...]

Transformers play a crucial role in power systems. In this respect, fault diagnosis and aging state assessment have garnered significant attention from researchers. Herein, accelerated thermal aging and Raman scattering experiments are conducted on oil–paper insulation samples to accurately detect aging states. The samples are categorized into different aging stages based on the polymerization degree of the insulating paper. Principal component analysis (PCA), multi-dimensional scale change method (MDS), and isometric mapping algorithm (Isomap) are employed to extract features from the Raman spectra. Subsequently, the XGBoost strong classifier, optimized through Bayesian hyperparameter optimization (BO-XGBoost), is utilized to distinguish between four and ten states among 175 groups of samples after feature extraction. The subsequent classification results of the three feature-extraction methods are compared. The results indicate that Isoamp, which pertains to the manifold dimension transformation, achieves the highest average discriminative accuracy after feature extraction. The discriminative accuracies for aging states four and ten are 97.0% and 95.1% respectively, demonstrating that Raman spectroscopy manifold dimension transformation enhances the distinctiveness between samples of different aging states in the feature-extraction process. The diagnostic model constructed with Isomap and BO-XGBoost enables accurate discrimination of the aging states of oil–paper insulation.

Oil-impregnated paper condenser transformer bushings are an important part of transformer equipment, and partial discharge (PD) occurred when defects exist on the condenser aluminum foil layers. Firstly, to study the PD process of the oil-paper insulated capacitance graded bushing with the defect of broken aluminum foil, a defective oil-paper bushing discharge sample is constructed to study the PD parameters and capacitance, and to discharge carbonization traces at different voltage levels. Then, in order to verify the process of condenser aluminum foil layer discharge and the space charge variation in the oil-paper insulation system of a sample model, the surface flashovers of a needle-plane discharge model based on the bipolar charge transport model and the hydrodynamic model was built. The simulation, by Transport of Diluted Species physics of COMSOL Multiphysics software, points out the discharge process of aluminum foil electrode caused by space charge action and electric field distortion under an electric field at different voltages. The results of simulation and sample bushing experiments showed that the PD process of the defective condenser foil layer is mainly divided into three stages: tip corona discharge, streamer in oil, and surface flashovers. The voltage amplitude is larger the more electrical branches are discharged and the shorter the discharge time is. The findings of the article have important implications for the discharge of the foil layer inside the oil-paper bushing.

A growing research interest currently exists in the use of paper as a building material. This work aims to present the results of a measurement campaign developed on innovative waste paper-based building components. The research was carried out in Southern Italy and used some local by-product aggregates. Three different mixture designs were developed in the laboratory by adding three kinds of biomass to a pulp paper blend: fava bean residues (FB), sawdust powder (SP) and coffee grains (CG) extracted from exhausted chaffs. A physical characterization was carried out measuring the bulk density and bulk porosity. Scanning Electron Microscopy (SEM) analysis of the single aggregates was followed by a microstructure analysis of the final components. Bulk density evaluation showed a range between 200 and 348 kg·m−3. Furthermore, thermal performances were measured; the thermal conductivity of the experimented samples ranged from 0.071 to 0.093 W·m−1·K−1, thus it is possible to classify the tested materials as thermal insulators. Moreover, the acoustic properties were evaluated and tested. The normal incidence sound absorption coefficient was measured by the impedance tube on cylindrical specimens. In general, a different behavior was observed between the upper and lower base of each specimen due to the manufacturing process and the shrinkage caused by the different interactions occurring between the aggregates and the pulp paper waste; for example, the presence of sawdust reduced shrinkage in the final specimens, with consequent smaller physical variations among the two faces. The correlation existing between the manufacturing process and the microstructural properties was also investigated by the estimation of the non-acoustical parameters using the inverse method and taking into account the JCA (Johnson, Champoux and Allard) model as a reference.

Carbon fiber paper (CFP) is one of the most important units of gas diffusion layer (GDL) in proton exchange membrane fuel cells (PEMFCs). The binder used in the wet-laid technique has a significant effect on the properties of CFP. In this work, the polyvinyl butyral/phenol-formaldehyde resin (PVB/PF) composite fibers firstly prepared by a dry spinning method were applied for CFP fabrication to replace traditional binders during the papermaking process and remove the PF impregnation process. In the composite fibers with a mass ratio of 5:5, PF phase with a size of about 2~3 μm evenly distributed in PVB matrix. PVB and PF were miscible to some degree, which was beneficial for their binding effect during hot-press. These composite fibers can successfully bind carbon fibers (CFs) during the papermaking process, and their residual carbon efficiently welded the CFs after heat treatment. The content and length of composite fibers in the mat affected the binding structure among CFs, which influenced the properties of CFP, increased the composite fibers’ content and reduced their length, significantly improving the strength of CFP. Therefore, the application of this solid fiber binder could enhance the comprehensive properties of CFP by adjusting the fibers’ parameters in the mat and also make the fabrication of CFP more environmentally friendly and low-cost.

The article presents a new technique for analyzing phenomena occurring during the measurement of the strength properties of paper in the conditions of compression of the tested samples with forces acting in the paper plane. The technique is based on collecting data on the current distance of the clamps holding the tested sample and the force exerted on the sample using a universal testing machine and on the simultaneous recording of image sequence of the sample during the measurement. Next, the resulting images are subjected to processing and analysis, the purpose of which is to extract information about the shape of the sample edge in all phases of the measurement. Its advantage is the ability to determine the deflection arrow of the sample and describe its shape using the selected function given by the analytical parametric formula. It will be helpful in further research on the development of an analytical model describing the phenomena occurring during paper compression, and a method to determine the mechanism of paper destruction and the corresponding maximum force that destroys a paper sample.

Nanoparticles have been in use for centuries [...]

This review analyzes the most influential artificial intelligence (AI) studies in health and life sciences from the past three years, delineating the evolving role of AI in these fields. We identified and analyzed the top 50 cited articles on AI in biomedicine, revealing significant trends and thematic categorizations, including Drug Development, Real-World Clinical Implementation, and Ethical and Regulatory Aspects, among others. Our findings highlight a predominant focus on AIs application in clinical settings, particularly in diagnostics, telemedicine, and medical education, accelerated by the COVID-19 pandemic. The emergence of AlphaFold marked a pivotal moment in protein structure prediction, catalyzing a cascade of related research and signifying a broader shift towards AI-driven approaches in biological research. The review underscores AIs pivotal role in disease subtyping and patient stratification, facilitating a transition towards more personalized medicine strategies. Furthermore, it illustrates AIs impact on biology, particularly in parsing complex genomic and proteomic data, enhancing our capabilities to disentangle complex, interconnected molecular processes. As AI continues to permeate the health and life sciences, balancing its rapid technological advancements with ethical stewardship and regulatory vigilance will be crucial for its sustainable and effective integration into healthcare and research.

This work reports on the development and performance evaluation of newly developed paper sheets coated, on both sides, with thin films of biodegradable poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) for applications of food packaging. For this, PHBV/paper/PHBV multilayers were first prepared by the thermo-sealing technique, optimizing the process variables of temperature and time. Thereafter, the multilayer sheets were characterized in terms of their morphological, optical, thermal, mechanical, and barrier properties and compared with equivalent paper structures double coated with high-barrier multilayer films of petrochemical polymers. The results indicated that the double coatings of PHBV successfully improved the mechanical resistance and ductility, protected from moisture, and also reduced the aroma and oxygen permeances of paper, having a minimal effect on its optical and thermal properties. Finally, the compostability of the resultant multilayer sheets was analyzed, confirming that the presence of the PHBV coatings slightly delayed the aerobic biodegradation and disintegration of paper.

This study investigated the effects of wearing AR devices on users’ performance and comfort ratings while performing order-picking (OP) tasks. In addition to a picking-by-paper list, two AR devices combined with three order information display designs were examined. Thirty adult participants joined. They searched for and found the boxes in the order list, picked them up, and returned to the origin. The time to complete the task and the number of incorrect boxes picked up were analyzed to assess the performance of the tasks. The subjective ratings of the participants on the comfort rating scale (CRS) and the simulator sickness questionnaire (SSQ) were collected to assess the designs of both the AR devices and the order information displays. It was found that the participants could complete the OP tasks faster when adopting the order map (4.97 ± 1.57 min) or the 3D graph display (4.87 ± 1.50 min) using either one of the AR devices than when using a paper list (6.03 ± 1.28 min). However, they needed more time to complete the OP tasks when wearing both types of AR glasses when the Quick Response (QR) code option was adopted (10.16 ± 4.30 min) than when using a paper list. The QR code scanning and display design using either one of the AR devices guaranteed 100% accuracy but sacrificed efficiency in task completion. The AR device with a binocular display and hand gesture recognition functions had a significantly lower CRS score in the dimensions of attachment and movement (5.6 and 6.3, respectively) than the corresponding dimensions (8.0 and 8.3, respectively) of the other device with a monocular and hand touch input design. There were complaints of eye strain after using both AR devices examined in this study. This implies that these AR devices may not be suitable to wear for extended periods of time. Users should take off the AR device whenever they do not need to view the virtual image to avoid eye strain and other discomfort symptoms.

Due to several of their characteristics, such as their renewability, sustainability, and eco-friendliness, nanocellulose-based materials are arousing growing interest from researchers in various fields of study and applications. The purpose of this review article is to provide an overall view of the most recent applications of these innovative bio-nanomaterials in the field of cultural heritage. First, an introduction of the different classes of cellulose nanomaterials and their synthesis and characterization methods is presented. After that, many consolidation treatments based on nanocellulose structures for the recovery of degraded and archeological wood, the stabilization of damaged painting canvases, and the deacidification of historical papers are shown in order to underline the advanced potential of nanocellulose for the conservation of artistic heritage and the respect for the environment.

The global drive to eliminate mercury is stimulating the development of LED lamps for UV curing of coatings. Despite its many advantages, the transition to this system in the furniture industry presents technological issues. This paper aimed to determine the impact of the paint line’s individual technological and process parameters on the coating’s optical properties, such as colour and gloss of furniture components made of white-coloured light-weight boards. Samples were prepared under the conditions of an industrial paint line using LED and traditional mercury lamps at the rate of 50 m/min. The colour was tested using the CIELAB system on a BYK GARDNER spectrophotometer, while the gloss was measured using the PICO GLOSS meter. Based on the data obtained, the optical parameters were found to be highly stable irrespective of the power drop in the LED lamps. The coordinates L*, b* and gloss G were affected by the amount of topcoat and basecoat, the number of coats, the mercury lamps’ power and the panel grinding programs used. The results of the tests showed that high L* and b* values could be achieved by increasing the number of overlays. This solution also ensures less basecoat and topcoat consumption, contributing to large material savings.

Document classification is an important area in Natural Language Processing (NLP). Because a huge amount of scientific papers have been published at an accelerating rate, it is beneficial to carry out intelligent paper classifications, especially fine-grained classification for researchers. However, a public scientific paper dataset for fine-grained classification is still lacking, so the existing document classification methods have not been put to the test. To fill this vacancy, we designed and collected the PaperNet-Dataset that consists of multi-modal data (texts and figures). PaperNet 1.0 version contains hierarchical categories of papers in the fields of computer vision (CV) and NLP, 2 coarse-grained and 20 fine-grained (7 in CV and 13 in NLP). We ran current mainstream models on the PaperNet-Dataset, along with a multi-modal method that we propose. Interestingly, none of these methods reaches an accuracy of 80% in fine-grained classification, showing plenty of room for improvement. We hope that PaperNet-Dataset will inspire more work in this challenging area.

Paper production and recycling result in large amounts of recycled paper sludge (RPS) that is currently being disposed of in very costly and unsustainable practices, raising the importance of developing green solutions for waste management. The use of nanocellulose (NC) as the next generation of materials has gained much attention due to its economic potential. However, there are substantial challenges in NC extraction, detection, and quantification methods. In this study, NC was produced from RPS as a means of converting waste into a resource. The process included a short, 30 min ozonation (21 mg O3/g RPS), which allowed a sufficient delignification and facilitated the following hydrolysis step. Among all tested durations, a 4-h hydrolysis with 64% w/w sulfuric acid resulted in the highest NC production. Fluorescent staining by calcofluor white was used for simple and low-cost detection of NC in-situ. Crude NC showed a significant 63% dye uptake of 0.1 ppm acid red 131 within 30 min. Compared to the standard disposal methods of RPS, its utilization for NC production supports the circular economy concept and significantly contributes to the development of cellulose bio-based nanomaterials for water treatment applications.

It is of great honor to present this Editorial for the Special Issue “Advances in Pulp and Paper Technologies” [...]

The microalgae–bacteria consortium is a promising and sustainable alternative for industrial wastewater treatment, since it may allow good removal of organic matter and nutrients, as well as the possibility of producing products with added value from the algae biomass. This research investigated the best bacterial and microalgae inoculation ratio for system start-up and evaluation of removing organic matter (as chemical oxygen demand (COD)), ammoniacal nitrogen (NH4+–N), nitrite nitrogen (NO2−–N), nitrate nitrogen (NO3−–N), phosphate phosphorus (PO43−–P) and biomass formation parameters in six photobioreactors with a total volume of 1000 mL. Reactors were operated for 14 days with the following ratios of pulp mill biomass aerobic (BA) and Scenedesmus sp. microalgae (MA): 0:1 (PBR1), 1:0 (PBR2), 1:1 (PBR3), 3:1 (PBR4), 5:1 (PBR5), and 1:3 (PBR6). Results show that COD removal was observed in just two days of operation in PBR4, PBR5, and PBR6, whereas for the other reactors (with a lower rate of initial inoculation) it took five days. The PBR5 and PBR6 performed better in terms of NH4+–N removal, with 86.81% and 77.11%, respectively, which can be attributed to assimilation by microalgae and nitrification by bacteria. PBR6, with the highest concentration of microalgae, had the higher PO43−–P removal (86%), showing the advantage of algae in consortium with bacteria for phosphorus uptake. PBR4 and PBR5, with the highest BA, led to a better biomass production and sedimentability on the second day of operation, with flocculation efficiencies values over 90%. Regarding the formation of extracellular polymeric substances (EPS), protein production was substantially higher in PBR4 and PBR5, with more BA, with average concentrations of 49.90 mg/L and 49.05 mg/L, respectively. The presence of cyanobacteria and Chlorophyceae was identified in all reactors except PBR1 (only MA), which may indicate a good formation and structuring of the microalgae–bacteria consortium. Scanning electron microscopy (SEM) analysis revealed that filamentous microalgae were employed as a foundation for the fixation of bacteria and other algae colonies.

This paper reports on the manufacture of ZnO nanoparticles (ZnO NPs) from Prosopis juliflora leaf extracts. Various methods of characterization were used, including X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscope (SEM), and transmission electron microscope TEM. ZnO NPs has a hexagonal wurtzite structure with a preferred orientation of 101 planes, according to XRD. The functional groups found in ZnO NPs isolated from leaves are responsible for the FT-IR peaks that correspond to them. The morphology of the produced nanoparticles is a sphere-like form, as shown in the SEM pictures. TEM examination revealed ZnO NPs with a size of 50–55 nm. These ZnO NPs were used to remediate pollutants in paper mill effluents, and they were able to remove 86% of the organic pollutants from the sample at 0.05 mg/L dose and reduce 89% of the organic pollutants during a 5-h reflex time. Meanwhile, for the photocatalysis of paper mill effluents, it has been noted that COD was removed by 74.30%, 63.23%, and 57.96% for the first, second, and third cycles, respectively.

Paper-ash is used for remediation of heavily contaminated soils with metals, but remediation efficiency after longer periods has not been reported. To gain insights into the mechanisms of immobilization of cadmium (Cd), lead (Pb), and znic (Zn), a study was performed in the laboratory experiment in uncontaminated, artificially contaminated, and remediated soils, and these soils treated with sulfate, to mimic conditions in contaminated soil from zinc smelter site. Remediation was performed by mixing contaminated soil with paper-ash to immobilize Cd, Pb, and Zn in the geotechnical composite. Partitioning of Cd, Pb, and Zn was studied over one year in seven-time intervals applying the sequential extraction procedure and complementary X-ray diffraction analyses. This methodological approach enabled us to follow the redistribution of Cd, Pb, and Zn over time, thus, to studying immobilization mechanisms and assessing the remediation efficiency and stability of newly formed mineral phases. Cd, Pb, and Zn were effectively immobilized by precipitation of insoluble hydroxides after the addition of paper-ash and by the carbonization process in insoluble carbonate minerals. After remediation, Cd, Pb, and Zn concentrations in the water-soluble fraction were well below the limiting values for inertness: Cd by 100 times, Pb by 125 times, and Zn by 10 times. Sulfate treatment did not influence the remediation efficiency. Experimental data confirmed the high remediation efficiency and stability of insoluble Cd, Pb, and Zn mineral phases in geotechnical composites.

In this study, the effect of air plasma on the surface properties of printed and coated cardboard was investigated. The material was activated by low-pressure cold plasma for 1, 10, 20, and 30 s. Wettability changes on the surface were examined by contact angle measurements using the sessile droplet technique. The differences in the surface free energy were calculated using the Lifshitz–van der Waals/acid–base and Contact Angle Hysteresis approaches. Optical profilometry was used for the surface roughness evaluation and an X-ray photoelectron spectroscopy analysis was performed to find changes in surface chemistry. Adhesive strength tests were carried out to estimate the adhesion changes after the material’s modification. It was found that the water and formamide contact angles increased after the plasma treatment while the diiodomethane contact angle did not change. As a result of the modification, the surface free energy also increased significantly and the surface roughness increased. The pull-off tests confirmed the improvement in the material’s surface properties. Moreover, it was demonstrated that the optimal effect can be obtained after just 10 s of the plasma process.

Paper sludge ash (PSA) typically has a low Si abundance and significant Ca content because of the presence of calcite fillers, which interfere with the zeolitic conversion of PSA. Ca-masking with ethylenediaminetetraacetic acid (EDTA) was used to reduce Ca interference during zeolite synthesis so that a zeolitic product with a high cation exchange capacity (CEC) could be synthesized. Hydroxysodalite, zeolite-P, hydroxycancrinite, tobermorite, and zeolite-A can be synthesized from PSA by an alkali reaction with EDTA. With the addition of EDTA, calcium ions in the solution were trapped by chelation, and the number of zeolitic crystals with low Si/Al (Si/Al = 1), zeolite-A, increased owing to the promotion of the synthesis reaction. A product with a high CEC that has a high zeolite-A content was obtained. The chelating agent can inhibit Ca interference for zeolite synthesis by Ca-masking, and a product with a high zeolite-A content can be obtained from PSA using EDTA.

In this paper, an organic, fully recyclable and eco-friendly 20-bit inkjet-printed chipless RFID tag is presented. The tag operates in the near field and is implemented by means of chains of resonant elements. The characterization and manufacturing process of the tag, printed with a few layers of a commercial organic ink on conventional paper substrate (DIN A4), are presented, and tag functionality is demonstrated by reading it by means of a custom-designed reader. The tags are read by proximity (through the near field), by displacing them over a resonator-loaded transmission line, and each resonant element (bit) of the tag is interrogated by a harmonic signal tuned to the resonance frequency. The coupling between the reader line and the resonant elements of the tag produce and amplitude modulated (AM) signal containing the identification (ID) code of the tag.

Surface hydrophobicity and grease resistance of paper may be achieved by the application of coatings usually derived from fossil-oil resources. However, poor recyclability and environmental concerns on generated waste has increased interest in the study of alternative paper coatings. This work focuses on the study of the performances offered by two different biopolymers, poly(3-hydroxybutyrate-co-3hydroxyvalerate) (PHBV) and polycaprolactone (PCL), also assessing the effect of a plasticizer (PEG) when used as paper coatings. The coated samples were characterized for the structural (by scanning electron microscopy, SEM), diffusive (water vapor and grease barrier properties), and surface properties (affinity for water and oil, by contact angle measurements). Samples of polyethylene-coated and fluorinated paper were used as commercial reference. WVTR of coated samples generally decreased and PHBV and PCL coatings with PEG at 20% showed interesting low wettability, as inferred from the water contact angles. Samples coated with PCL also showed increased grease resistance in comparison with plain paper. This work, within the limits of its lab-scale, offers interesting insights for future research lines toward the development of cellulose-based food contact materials that are fully recyclable and compostable.

To explore whether the brain contains pattern differences in the rock–paper–scissors (RPS) imagery task, this paper attempts to classify this task using fNIRS and deep learning. In this study, we designed an RPS task with a total duration of 25 min and 40 s, and recruited 22 volunteers for the experiment. We used the fNIRS acquisition device (FOIRE-3000) to record the cerebral neural activities of these participants in the RPS task. The time series classification (TSC) algorithm was introduced into the time-domain fNIRS signal classification. Experiments show that CNN-based TSC methods can achieve 97% accuracy in RPS classification. CNN-based TSC method is suitable for the classification of fNIRS signals in RPS motor imagery tasks, and may find new application directions for the development of brain–computer interfaces (BCI).

The study of materials has entailed several efforts by materials scientists to gain a deep understanding of their structural, mechanical, chemical, optical, magnetic and electronic properties and engineering applications [...]

This study compares the performance of graph convolutional neural network (GCN) models with conventional natural language processing (NLP) models for classifying scientific literature related to radio frequency electromagnetic field (RF-EMF). Specifically, the study examines two GCN models: BertGCN and the citation-based GCN. The study concludes that the model achieves consistently good performance when the input text is long enough, based on the attention mechanism of BERT. When the input sequence is short, the composition parameter λ, which combines output values of the two subnetworks of BertGCN, plays a crucial role in achieving high classification accuracy. As the value of λ increases, the classification accuracy also increases. The study also proposes and tests a simplified variant of BertGCN, revealing performance differences among the models under two different data conditions by the existence of keywords. This study has two main contributions: (1) the implementation and testing of a variant of BertGCN and citation-based GCN for document classification tasks related to radio frequency electromagnetic fields publications, and (2) the confirmation of the impact of model conditions, such as the existence of keywords and input sequence length, in the original BertGCN. Although this study focused on a specific domain, our approaches have broader implications that extend beyond scientific publications to general text classification.

Fungi are the main contaminants of books and archival documents. In addition to their degrading power, offered by various types of lignolytic and cellulolytic enzymes, they can also hue the surface of the paper through the production of pigments. The fungi on paper release various types of pigments belonging mostly to two chemical groups (polyketides and carotenoids), which cause unpleasant anaesthetic stains. The paper surface can also be hued with several synthetic colors, which are part, for example, of stamps and inks. These synthetic colors could be degraded by lignin-modifying enzymes (LMEs) and also by dye-decolorizing peroxidases (DyPs). Therefore, the mechanism of action of LEMs and DyPs is illustrated. Moreover, we have examined the potentiality of LEMs and DyPs to remove the synthetic stains and also their hypothetical application in order to clean the fungal hues from the paper surface. Our review article, using the enzymatic removal parallelism between fungal and synthetic pigments, would like to show prospective solutions to this arduous problem.

Softness is one of the essential properties of hygiene tissue products. Reliably measuring it is of utmost importance to ensure the balance between customer expectations and cost-effective tissue production. This study presents a method for assessing softness by analyzing acoustic emissions produced while tearing a tissue specimen. The aim was to train neural network models using the corrected results of human panel tests as the ground truth labels and to predict the tissue softness in two- and three-class recognition tasks. We also investigate the possibility of predicting some production parameters related to the softness property. The results proved that tissue softness and production parameters could be reliably estimated only by the tearing noise.

This paper deals with the valorization of waste paper fly ash (WPFA) as a binder for soil stabilization. The mineralogical characterization shows the presence of free lime, as well as some non-reactive and cementitious phases. The hydration of lime is an expansive reaction and can be problematic in soil stabilization. Therefore, to study its effect on stabilized soil, an in-house experimental set-up is proposed to measure the possible expansion. Furthermore, to study the effect of water reduction and delay time on strength, unconfined compressive strength with different mixes is conducted. The obtained results showed that using WPFA causes expansion in stabilized soil, but a delay time of 30 min, after mixing the material with water and then compacting it, can decrease the expansion. Additionally, decreasing the water content by a point of Proctor can be essential for improving the strength in soil samples, even reaching the same strength values as control samples cured at 7 days. Finally, all the results obtained in this study have shown that WPFA is a suitable material for use as a binder for soil stabilization while reducing its optimum water content, adding a proper delay time, and taking into consideration WPFA’s expansive behavior at the moment of its use.