Search

The molecular imaging of paper cross sections containing the wet-strength additive poly(amidoamine)-epichlorohydrin (PAE) was effected by Fourier transform infrared (FT-IR) spectroscopic imaging. Thin cross sections of laboratory sheet samples were prepared and transferred onto CaF substrates. A laboratory sheet sample without PAE acted as a reference. Principal component analysis (PCA) was applied to identify and to reveal the distribution of PAE across the section. Differences in the loading plots of the fourth and fifth principal components for the sheets with and without PAE were found in the region of the amide I, amide II, and amine bands within a variance of 0.4-0.8 %. The score images of the PCA reveal inhomogeneous distribution of PAE. Small areas of higher concentration of PAE occur across the cross section. The aim of this study was to demonstrate that FT-IR spectroscopic imaging provides spatially resolved quantitative information about the chemical composition of paper, which was successfully achieved. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Paper-based scaffolds are an attractive material for generating 3D tissue-like cultures because paper is readily available and does not require specialized equipment to pattern, cut, or use. By controlling the exchange of fresh culture medium with the paper-based scaffolds, we can engineer diffusion-dominated environments similar to those found in spheroids or solid tumors. Oxygen tension directly regulates cellular phenotype and invasiveness through hypoxia-inducible transcription factors and also has chemotactic properties. To date, gradients of oxygen generated in the paper-based cultures have relied on cellular response-based readouts. In this work, we prepared a luminescent thin film capable of quantifying oxygen tensions in apposed cell-containing paper-based scaffolds. The oxygen sensors, which are polystyrene films containing a Pd(II) tetrakis(pentafluorophenyl)porphyrin dye, are photostable, stable in culture conditions, and not cytotoxic. They have a linear response for oxygen tensions ranging from 0 to 160 mmHg O, and a Stern-Volmer constant ( K) of 0.239 ± 0.003 mmHg O. We used these oxygen-sensing films to measure the spatial and temporal changes in oxygen tension for paper-based cultures containing a breast cancer line that was engineered to constitutively express a fluorescent protein. By acquiring images of the oxygen-sensing film and the fluorescently labeled cells, we were able to approximate the oxygen consumption rates of the cells in our cultures. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

A disposable electrochemical lateral flow paper-based sensing device for heavy metal detection is proposed. The quantification of lead and cadmium in aqueous samples is demonstrated in a range from 10 to 100 ppb with a limit of detection of 7 and 11 ppb respectively. Moreover, the platform itself, which is made of paper, served as a sample pretreatment material due to its filtering properties. Real samples, especially in which the matrix is usually turbid and would in principle need a previous filtration, are successfully analyzed. This lab-on-paper device is simple, low cost, easy to fabricate, and portable, being a promising tool for new point-of-care applications in environmental monitoring, public health, and food safety. [ABSTRACT FROM AUTHOR]

In this report, we present a paper membrane-based surface-enhanced Raman scattering (SERS) platform for the determination of blood glucose level using a nitrocellulose membrane as substrate paper, and the microfluidic channel was simply constructed by wax-printing method. The rod-shaped gold nanorod particles were modified with 4-mercaptophenylboronic acid (4-MBA) and 1-decanethiol (1-DT) molecules and used as embedded SERS probe for paper-based microfluidics. The SERS measurement area was simply constructed by dropping gold nanoparticles on nitrocellulose membrane, and the blood sample was dropped on the membrane hydrophilic channel. While the blood cells and proteins were held on nitrocellulose membrane, glucose molecules were moved through the channel toward the SERS measurement area. Scanning electron microscopy (SEM) was used to confirm the effective separation of blood matrix, and total analysis is completed in 5 min. In SERS measurements, the intensity of the band at 1070 cm which is attributed to B-OH vibration decreased depending on the rise in glucose concentration in the blood sample. The glucose concentration was found to be 5.43 ± 0.51 mM in the reference blood sample by using a calibration equation, and the certified value for glucose was 6.17 ± 0.11 mM. The recovery of the glucose in the reference blood sample was about 88 %. According to these results, the developed paper-based microfluidic SERS platform has been found to be suitable for use for the detection of glucose in blood samples without any pretreatment procedure. We believe that paper-based microfluidic systems may provide a wide field of usage for paper-based applications. [ABSTRACT FROM AUTHOR]

Paper-based devices serve to address many analytical questions both inside and outside of the laboratory setting. For the first time, yeast is used to construct a whole-cell, paper-based biosensor device. This biologically based paper analytical device (BioPAD) is sensitive to antibiotics in the tetracycline family, and it could potentially address questions of pharmaceutical quality as well as antibiotic contamination in liquids. Our BioPAD can qualitatively discriminate the presence/absence of doxycycline over a range of 30-10,000 μg/mL. In an analysis of a doxycycline dosage form (tablet) commonly used for malaria prophylaxis, BioPADs identified the presence of antibiotic with 92 and 95 % sensitivity, evaluated by eye and computer-assisted image analysis, respectively, with no false positives by either method. BioPADs were found to remain viable for at least 415 days when stored at 4 °C. This research demonstrates the utility of whole yeast cells in paper-based pharmaceutical testing, and it highlights the potential for the development of yeast-based BioPADs to address a range of qualitative analytical questions, especially in low resource settings. [ABSTRACT FROM AUTHOR]

Rapid, sensitive, on-site detection of bacteria without a need for sophisticated equipment or skilled personnel is extremely important in clinical settings and rapid response scenarios, as well as in resource-limited settings. Here, we report a novel approach for selective and ultra-sensitive multiplexed detection of Escherichia coli (non-pathogenic or pathogenic) using a lab-on-paper test strip (bioactive paper) based on intracellular enzyme (β-galactosidase (B-GAL) or β-glucuronidase (GUS)) activity. The test strip is composed of a paper support (0.5 × 8 cm), onto which either 5-bromo-4-chloro-3-indolyl-β- d-glucuronide sodium salt (XG), chlorophenol red β-galactopyranoside (CPRG) or both and FeCl were entrapped using sol-gel-derived silica inks in different zones via an ink-jet printing technique. The sample was lysed and assayed via lateral flow through the FeCl zone to the substrate area to initiate rapid enzyme hydrolysis of the substrate, causing a change from colorless-to-blue (XG hydrolyzed by GUS, indication of nonpathogenic E. coli) and/or yellow to red-magenta (CPRG hydrolyzed by B-GAL, indication of total coliforms). Using immunomagnetic nanoparticles for selective preconcentration, the limit of detection was ~5 colony-forming units (cfu) per milliliter for E. coli O157:H7 and ~20 cfu/mL for E. coli BL21, within 30 min without cell culturing. Thus, these paper test strips could be suitable for detection of viable total coliforms and pathogens in bathing water samples. Moreover, inclusion of a culturing step allows detection of less than 1 cfu in 100 mL within 8 h, making the paper tests strips relevant for detection of multiple pathogens and total coliform bacteria in beverage and food samples. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Paper-based artworks are among the most valuable assets for transmission of knowledge. Historical paper is composed of different polysaccharides (e.g. cellulose), binders, and glues. During aging all of these components undergo several degradation processes, as a result of external and intrinsic causes, and these can compromise the state of conservation of the document. In this work, application of a new biotechnological strategy for paper artefact preservation is reported. By making use of innovative and non-invasive materials, for example appropriate hydrogels, in combination with selective electrochemical biosensors, it is possible to simultaneously verify the degradation condition of the paper artwork and then to efficiently clean it, while monitoring the process of removal of both pollution and degradation products. In this paper, we focus on specific examples in which such techniques have been applied to paper artworks and that illustrate the advantages and potential of this biotechnology compared with the traditional paper-cleaning methods currently in use. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Methylmalonic aciduria is a common inherited metabolic disorder. Methylmalonic acid (MMA), a key indicator of methylmalonic aciduria, increases in the amniotic fluid of affected fetuses. For prenatal diagnosis, the MMA in amniotic fluid can be measured by stable-isotope dilution gas chromatography-mass spectrometry. Here, we quantified the MMA in cell-free amniotic fluid samples that had been dried on filter paper and transported at ambient temperatures, and compared the results with data obtained from the original amniotic fluid. Our results indicated that the filter paper method was reproducible and accurate enough to be applied to clinical analysis. We also used the filter paper method to screen at-risk fetuses and obtained a clear diagnosis in each case. We conclude that our method enables the prenatal diagnosis of methylmalonic aciduria using practical procedures and a simplified method for transporting the samples. [ABSTRACT FROM AUTHOR]

NMR spectroscopy of urine samples is able to diagnose many inborn errors of metabolism (IEM). However, urinary metabolites have a poor stability, requiring special care for routine analysis (storage of urine at −20 or −80 °C, fast transport). The aim of our study was to investigate the reliability of dried urine filter paper for urine storage and transport and to evaluate the ability of NMR to detect several IEM using this method. Urine samples from five healthy subjects were analyzed by 1H NMR following different storage conditions (−20 vs 4 °C vs dried on filter paper) and at different time points (24 h, 48 h, 96 h, and 7 days). Urine pattern of fresh urine was considered as a reference. We analyzed the conservation of some amino acids and organic acids using Bland and Altman plot with intraclass correlation coefficient determination. Then, we evaluated the use of filter paper to detect four different IEM (methylmalonic and isovaleric acidurias, ornithine transcarbamylase deficiency, and cystinuria). Analysis of urine samples from healthy subjects revealed a high stability of studied molecules (ICC > 0.8) even after 7 days of storage on filter paper. Moreover, an excellent preservation of metabolites specifically accumulated in IEM was observed when analysis of dried urine filter paper was compared to fresh urine (coefficient of variation < 15%). This preliminary study demonstrates that storage of dried urine on filter paper is reliable for 1H NMR spectroscopy analysis. Preservation of urine molecules over time using that method is convenient for routine clinical practice. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

A simple and fast method based on paper spray mass spectrometry for the determination of caffeine in commercial beverages and drugs has been developed; the analyses were carried out in MRM mode, monitoring the transitions m/z 195 → m/z 138 for caffeine and m/z 198 → m/z 140 for the labeled internal standard. To verify the reliability of the proposed approach, a spiked sample (soda drink and paracetamol tablet) with a known amount of caffeine has been prepared and analyzed by PS-MS, providing accuracy values about 100 %; the LOQ and LOD values were calculated at 1.2 and 1.6 μg/mL, respectively. Both beverages and drugs were also analyzed with the classic analytical method based on LC-UV measurements, showing consistent results between the two approaches, thus confirming the reliability of the developed ambient MS determination. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Screening programs for pediatric lead (Pb) poisoning routinely collect blood by finger stick onto specially designed filter paper (FP) for subsequent laboratory testing. Here, laser ablation inductively coupled plasma time-of-flight mass spectrometry is evaluated as a novel method for the determination of Pb in blood spotted onto FP cards. The method requires no sample pretreatment and may be particularly suitable for rapidly screening a large number of samples. Signal intensity from the ICP-MS strongly correlated ( r 2 = 0.996) with Pb target values for five blood cards from a laboratory proficiency testing program. Better precision was obtained by replicate ablation line scans (<15% rsd) compared to a grid of 25 individual ablation spots (>30% rsd). Because <2% of the sample is consumed in the laser ablation analysis, selected samples can also be analyzed by traditional techniques or archived. Lead isotope ratios determined during the same total-Pb analysis appear to be effective for discerning contamination extraneous to the blood sample. Determining that an elevated result was due to contamination may negate the need for retesting with invasive pediatric venipuncture. Some elements monitored along with Pb exhibited signal profiles conducive to potential quantitation (Ca, V, Fe, Cu Zn), whereas others did not (Cr, Mn, Co, Ni, Cd, Hg, Tl, U). Copper, Ca, and V were inversely correlated with Pb ( r = −0.89, −0.90, and −0.92, respectively). Scanning electron microscope images revealed surface modality differences between FP spotted with fresh whole blood and reconstituted freeze-dried blood reference material. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

We report the use of paper-based microfluidic devices fabricated from a novel polymer blend for the monitoring of urinary ketones, glucose, and salivary nitrite. Paper-based devices were fabricated via photolithography in less than 3 min and were immediately ready for use for these diagnostically relevant assays. Patterned channels on filter paper as small as 90 μm wide with barriers as narrow as 250 μm could be reliably patterned to permit and block fluid wicking, respectively. Colorimetric assays for ketones and nitrite were adapted from the dipstick format to this paper microfluidic chip for the quantification of acetoacetate in artificial urine, as well as nitrite in artificial saliva. Glucose assays were based on those previously demonstrated (Martinez et al., Angew Chem Int Ed 8:1318–1320, ; Martinez et al., Anal Chem 10:3699–3707, ; Martinez et al., Proc Nat Acad Sci USA 50:19606–19611, ; Lu et al., Electrophoresis 9:1497–1500, ; Abe et al., Anal Chem 18:6928–6934, ). Reagents were spotted on the detection pad of the paper device and allowed to dry prior to spotting of samples. The ketone test was a two-step reaction requiring a derivitization step between the sample spotting pad and the detection pad, thus for the first time, confirming the ability of these paper devices to perform online multi-step chemical reactions. Following the spotting of the reagents and sample solution onto the paper device and subsequent drying, color images of the paper chips were recorded using a flatbed scanner, and images were converted to CMYK format in Adobe Photoshop CS4 where the intensity of the color change was quantified using the same software. The limit of detection (LOD) for acetoacetate in artificial urine was 0.5 mM, while the LOD for salivary nitrite was 5 μM, placing both of these analytes within the clinically relevant range for these assays. Calibration curves for urinary ketone (5 to 16 mM) and salivary nitrite (5 to 2,000 μM) were generated. The time of device fabrication to the time of test results was about 25 min. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

A new analytical approach, using paper spray tandem mass spectrometry, has been developed for assay of carnitine and acylcarnitines in urine. Paper spray (PS) is a very promising technique, especially in clinical investigations, because of its simplicity, low cost, and rapid sample preparation. A home-made paper spray device was used for assay of urinary acylcarnitines (C2-C18). The performance of solvents with different elution efficiency and paper substrates with different porosity grade and structure were tested by use of spiked synthetic urine. Tandem mass spectrometry in multiple reaction monitoring (MRM) mode was optimized to obtain better specificity and sensitivity. Analyte signals were evaluated for stability and reproducibility. Calibration with [H]propionylcarnitine (C3-d3), [H]octanoylcarnitine (C8-d3), and [H] palmitoylcarnitine (C16-d3) as internal standards was used for quantification. Very good linearity was obtained, with correlation coefficients >0.99 for C0-C12 and C16 acylcarnitines and >0.96 for C14 and C18 acylcarnitines. Accuracy and precision (RSD, %) of the proposed procedure were tested at concentrations of 0.8, 8, and 20 mg L with very satisfactory results: overall mean accuracy was 98.9 % and overall mean relative standard deviation 1 %. Limits of detection (LOD) between 6 and 208 μg L for propionylcarnitine and tetradecanoylcarnitine, respectively, can be regarded as very satisfactory. Application of the method to real urine proved that paper spray tandem mass spectrometry is a simple, rapid, and direct tool (no derivatization is required) for assay of carnitine and C2-C12 acylcarnitines in urine. [ABSTRACT FROM AUTHOR]

An interview with Elise Dennis, a Ph.D. candidate in analytical chemistry at Indiana University, who has won the ABC Best Paper Award 2014 for her work published in the periodical "Analytical and Bioanalytical Chemistry" (ABC), is presented. Dennis talks about her motivation for doing research on zoom-time-of-flight mass spectrometry (zoom-TOFMS), her Ph.D. research on zoom-TOFMS and distance-of-flight mass spectrometry (DOFMS), and her plans for atomic mass spectrometry research in future.

Chemi(bio)luminometric assays have contributed greatly to various areas of nucleic acid analysis due to their simplicity and detectability. In this work, we present the development of chemiluminometric genotyping methods in which (a) detection is performed by using either a conventional digital camera (at ambient temperature) or a smartphone and (b) a lateral flow assay configuration is employed for even higher simplicity and suitability for point of care or field testing. The genotyping of the C677T single nucleotide polymorphism (SNP) of methylenetetrahydropholate reductase (MTHFR) gene is chosen as a model. The interrogated DNA sequence is amplified by polymerase chain reaction (PCR) followed by a primer extension reaction. The reaction products are captured through hybridization on the sensing areas (spots) of the strip. Streptavidin-horseradish peroxidase conjugate is used as a reporter along with a chemiluminogenic substrate. Detection of the emerging chemiluminescence from the sensing areas of the strip is achieved by digital camera or smartphone. For this purpose, we constructed a 3D-printed smartphone attachment that houses inexpensive lenses and converts the smartphone into a portable chemiluminescence imager. The device enables spatial discrimination of the two alleles of a SNP in a single shot by imaging of the strip, thus avoiding the need of dual labeling. The method was applied successfully to genotyping of real clinical samples. [ABSTRACT FROM AUTHOR]

The colorimetric determination of the concentration of polyphenols, flavonoids, and anthocyanins in wine samples, using a mobile phone camera for sample spot capture on a paper microzone and a remote computer with dedicated software for quantification, is presented as an illustrative application of green analytical chemistry. A comparison of the results with conventional spectrophotometry demonstrates that both methods yield similar results. Developing the assay took approximately 2 months, and the use of chemicals, compared with spectrophotometry, was reduced by about two orders of magnitude: the paper assay consumed 0.4 mL of reagent for 100 samples, whereas the spectrophotometric assay required 100 mL. The relative testing times for 100 samples were 7 h by spectrophotometry and 2 h for paper-a savings on the order of 3.5. No analytical instrumentation was used for the colorimetry on paper microzones. Instead, the assay took advantage of the existing communication technology and free software. The assay was found to be effective, with a nonlinear response at the concentration range of 0.2-5 g/L. The detection limit of the proposed method is in sub-grams per liter. [ABSTRACT FROM AUTHOR]

The aim of the research project 'Typology of Dutch Drawing' was to establish an interdisciplinary approach for investigating heterogeneous drawing collections. To define a type common to a group of drawings, we determine elements that are common to them based on style and the use of identical materials. To that end, we investigated about 750 Dutch drawings from the sixteenth century at the Dresden Kupferstich-Kabinett using art historical and scientific methods. In this work, we present a detailed analysis of 30 drawings ascribed to the Egmont Master. [ABSTRACT FROM AUTHOR]

This article describes the use of microfluidic paper-based analytical devices (μPADs) to perform quantitative chemical assays with internal standards. MicroPADs are well-suited for colorimetric biochemical assays; however, errors can be introduced from the background color of the paper due to batch difference and age, and from color measurement devices. To reduce errors from these sources, a series of standard analyte solutions and the sample solution are assayed on a single device with multiple detection zones simultaneously; an analyte concentration calibration curve can thus be established from the standards. Since the μPAD design allows the colorimetric measurements of the standards and the sample to be conducted simultaneously and under the same condition, errors from the above sources can be minimized. The analytical approach reported in this work shows that μPADs can perform quantitative chemical analysis at very low cost. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

The use of electrospun nanofibers as functional material in paper-based lateral flow assays (LFAs) was studied. Specific chemical features of the nanofibers were achieved by doping the base polymer, poly(lactic acid) (PLA), with poly(ethylene glycol) (PEG) and polystyrene- block-poly(ethylene- ran-butylene)- block-polyisoprene-Brij76 (K3-Brij76) (KB). The LFAs were assembled such that the sample flowed through the nanofiber mat via capillary action. Initial investigations focused on the sustainable spinning and assembly of different polymer structures to allow the LFA format. Here, it was found that the base polymer poly(vinyl alcohol) (PVA), which was shown to function well in microfluidic biosensors, did not work in the LFA format. In contrast, PLA-based nanofibers enabled easy assembly. Three relevant features were chosen to study nanofiber-based functionalities in the LFA format: adsorption of antibodies, quantification of results, and nonspecific binding. In particular, streptavidin-conjugated sulforhodamine B (SRB)-encapsulating liposomes were captured by anti-streptavidin antibodies adsorbed on the nanofibers. Varying the functional polymer concentration within the PLA base enabled the creation of distinct capture zones. Also, a sandwich assay for the detection of Escherichia coli O157:H7 was developed using anti- E. coli antibodies as capture and reporter species with horseradish peroxidase for signal generation. A dose-response curve for E. coli with a detection limit of 1.9 × 10 cells was achieved. Finally, functional polymers were used to demonstrate that nonspecific binding could be eliminated using antifouling block copolymers. The enhancement of paper-based devices using functionalized nanofibers provides the opportunity to develop a broad spectrum of sensitive and specific bioassays with significant advantages over their traditional counterparts. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

A prototype of a fast-response task-specific amperometric gas sensor based on paper-supported room-temperature ionic liquids (RTILs) is proposed here for improved analysis of volatile acid species. It consists of a small filter paper foil soaked with a RTIL mixture containing an ionic liquid whose anion (acetate) displays a basic character, upon which three electrodes are screen printed by carbon ink profiting from a suitable mask. It takes advantage of the high electrical conductivity and negligible vapour pressure of RTILs and of their easy immobilization into a porous and inexpensive supporting material such as paper. The performance of this device, used as a wall-jet amperometric detector for flow injection analyses of headspace samples in equilibrium with aqueous solutions at controlled concentrations, was evaluated for phenol and 1-butanethiol vapours which were adopted as model acid gaseous analytes. The results obtained showed that the quite high potentials required for the detection of these analytes are lowered significantly, thanks to the addition of the basic acetate RTIL. In such a way, overlap with the medium discharge is avoided, and the possible adverse effect of interfering species is minimised. The sensor performance was quite satisfactory (detection limits, ca. 0.3 μM; dynamic range, ca. 1-200 μM, both referred to solution concentrations; correlation coefficients in the range 0.993-0.997; repeatability, ± 6 % RSD; long-term stability, 9 %); thus suggesting the possible use of this device for manifold applications. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

Graphene-nanosheet-based highly porous magnetite nanocomposites (GN-HPMNs) have been prepared using a simple solvothermal method and used as an immobilization matrix for the fabrication of a solid-state electrochemiluminescence (ECL) sensor on paper-based chips. Highly porous FeO nanocrystal clusters were coated with acrylate and wrapped tightly on the skeleton of graphene nanosheets. The structures and sizes of the GN-HPMNs could be tuned by varying the proportions of the solvents ethylene glycol and diethylene glycol. Then, the relatively highly porous ones with an average diameter of about 65 nm were combined with Nafion to form composite films on an electrode surface for immobilization of Ru(bpy) (bpy is 2,2′-bipyridine). Because of their porosity, negatively charged surface, and cooperative characteristics of magnetic nanomaterials and graphene, under an external magnetic field, the GN-HPMNs ensured effective immobilization, excellent electron transfer, and long-term stability of Ru(bpy) in the composite film. The sensor developed exhibited excellent reproducibility with a relative standard deviation of 0.65 % for 30 continuous cycles. It was found to be much more favorable for detecting compounds containing tertiary amino groups and DNAs with guanine and adenine. A detection limit (signal-to-noise ratio of 3) of 5.0 nM was obtained for tripropylamine. As an application example, 0.5 nM single-nucleotide mismatch could be detected. This was the first attempt to introduce magnetic nanomaterials and an external magnetic field into paper-based chips. The sensor developed has the advantages of high sensitivity, good stability, and wide potential applicability as well as simplicity, low cost, and good disposability. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

A simple protocol for rapid quantitation of acylcarnitines in serum and whole blood has been developed using paper spray mass spectrometry. Dried serum and whole blood containing a mixture of ten acylcarnitines at various concentrations were analyzed as spots from paper directly without any sample pretreatment, separation, or derivatization. The composition of the spray solvent was found to be a critical factor: for serum samples, spray solvent of methanol/water/formic acid (80:20:0.1) gave the best signal intensity while for blood samples which contain more matrix components, acetonitrile/water (90:10) was a much more suitable spray solvent. For the paper type and size used, 0.5 μL of sample provided an optimal signal for both serum and whole blood samples. For quantitative profiling, the limits of quantitation obtained from both serum and blood were much lower than the clinically validated cutoff values for diagnosis of fatty acid oxidation disorders in newborn screening. Linearity ( R > 0.95) and reproducibility (RSD ∼10 %) were achieved in the concentration ranges from 100 nM to 5 μM for the C2 acylcarnitine, and for other acylcarnitines, these values were from 10 to 500 nM. Acylcarnitine profiles offer an effective demonstration of the fact that paper spray mass spectrometry is an appropriate, simple, rapid method with high sensitivity and high reproducibility applicable to newborn screening tests. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

This paper reports on an inkjet printing method for the fabrication of lateral flow immunochromatographic devices made from a single piece of filter paper by patterning microfluidic channels and dispensing immunosensing inks, requiring only a single printing apparatus. This “paperfluidic” immunosensing device allows for a less time-consuming and more low-cost fabrication compared with the conventional immunochromatographic strips requiring multiple pads, plastic or nylon backing, and a plastic case. A sandwich immunoreaction was performed on the patterned immunosensing paper device, and the sensitivity of the device was optimized with an IgG model analyte. Inkjet-printed antibodies on the test line and the control line were immobilized by physical adsorption, resulting in a very simple fabrication method applicable for pure cellulose surfaces. The color intensity in the test line and the control line was determined both by naked eye and by means of a color scanner in combination with a simple computer program. With the resulting paperfluidic immunosensing device, human IgG concentrations at least down to 10 μg/l could be detected within 20 min. Additionally, in order to demonstrate the feasibility of a total multianalyte sensing system, a combined immuno-chemical sensing device was also fabricated by patterning an additional microfluidic channel for a chemical assay onto the same paper substrate. This low-cost multianalyte paperfluidic sensing device thus demonstrates the feasibility of simple, portable, and disposable tools for pathogen detection in the field of medical, environmental, and food analyses, possibly resulting in useful devices in remote settings and less-industrialized countries. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

This paper deals with the study of the kinetic migration of a series of organic compounds representative of potential contaminants in packaging materials and used as surrogates ( o-xylene, acetophenone, dodecane, naphthalene, 2,3,4-trichloroanisole, benzophenone, isomeric mix of diisopropylnaphthalene, diisobutyl phthalate and methyl stearate). Migration to one side of a solid simulant, Tenax®, also referred to as MPPO (modified polyphenylene oxide), was investigated in this study. One spiked sample of multilayer material was used to optimise the extraction procedures for the multilayer paper-based material and the Tenax as well as to perform kinetic migration studies. Three sequential extractions using ethanol were necessary for the strips of the multilayer material but only one extraction was necessary for the solid simulant to obtain >70% recovery of the surrogates. These results enabled us to specify the extraction requirements of the multilayer sample and the solid simulant and as well as those of the migration tests at high temperature using Tenax as solid simulant. The matrix effect associated with the extraction of the contaminants from the multilayer sample is also discussed. [ABSTRACT FROM AUTHOR]

Foodborne pathogens are a burden to the economy and a constant threat to public health. The ability to rapidly detect the presence of foodborne pathogens is a vital component of any strategy towards establishing a safe and secure food supply chain. Bacteriophages (phages) are viruses capable of infecting and replicating within bacteria in a strain-specific manner. The ubiquitous and selective nature of phages makes them ideal for the detection and biocontrol of bacteria. Therefore, the objective of this research was to develop and test a phage-based paper dipstick biosensor for the detection of various foodborne pathogens in food matrices. The first step was to identify the best method for immobilizing phages on paper such that their biological activity (infectivity) was preserved. It was found that piezoelectric inkjet printing resulted in lower loss of phage infectivity when compared with other printing methods (namely gravure and blade coating) and that ColorLok paper was ideally suited to create functional sensors. The phage-based bioactive papers developed with use of piezoelectric inkjet printing actively lysed their target bacteria and retained this antibacterial activity for up to 1 week when stored at room temperature and 80% relative humidity. These bioactive paper strips in combination with quantitative real-time PCR were used for quantitative determination of target bacteria in broth and food matrices. A phage dipstick was used to capture and infect Escherichia coli O157:H7, E. coli O45:H2, and Salmonella Newport in spinach, ground beef and chicken homogenates, respectively, and quantitative real-time PCR was used to detect the progeny phages. A detection limit of 10-50 colony-forming units per millilitre was demonstrated with a total assay time of 8 h, which was the duration of a typical work shift in an industrial setting. This detection method is rapid and cost-effective, and may potentially be applied to a broad range of bacterial foodborne pathogens. [ABSTRACT FROM AUTHOR]

The fabrication concept for a low-cost sensor device using reduced graphene oxide (rGO) as the sensing material on a porous paper substrate is presented. The sensors were characterized using conductivity and capacitance measurements, atomic force microscopy and X-ray photoelectron spectroscopy. The effects of different reducing agents, graphene oxide (GO) flake size and film thickness were studied. The sensor was sensitive to NO, and devices based on a thin (10-nm) hydrazine-reduced GO layer had the best sensitivity, reaching a 70 % reduction in resistance after 10 min of exposure to 10 ppm NO. The sensitivity was high enough for the detection of sub-parts per million levels of NO. Desorption of gas molecules, i.e. the recovery of the sensor, could be accelerated by UV irradiation. The structure and preparation of the sensor are simple and up-scalable, allowing their fabrication in bulk quantities, and the fabrication concept can be applied to other materials, too. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

An Interview with Yaohua Wang, the winner of this journal's Best Paper Award for 2012 for her research work on the bioactivity of organelles found in eukaryotic cells called peroxisomes, is presented. When asked about the motivation to perform research in her area of interest, she says that she wanted to explore the field of cancer treatment. She expresses her admiration for her advisor Edgar Arriaga, a chemistry researcher, and discusses her interest in traveling to different places.

An innovative approach to date fiber-based gelatin silver prints using near-infrared spectroscopy (NIR) and multivariate analysis is presented. NIR spectra were acquired for 152 film stills printed in the USA between 1914 and 1986, and partial least square (PLS) analysis was used to correlate the spectra with the year the photographs were printed. Principal component analysis and spectral interpretation helped clarify the underlying correlation between the print date and the composition and ageing of the photographic papers. The method was successfully validated with an independent set of 66 film stills printed in the USA, and a prediction error (root mean square error of prediction) of 6 years was achieved. The method was also tested on films stills printed in Germany and Russia, as well as amateur prints and photographs in the collection of the Museum of Modern Art. The prediction error was significantly larger, with the exception of the amateur prints, due to differences in the composition and/or properties of the papers depending on their geographical origin and purpose as confirmed by discriminant analysis. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

The optimization of a clean procedure based on ultrasound-assisted emulsification liquid-liquid microextraction for the sensitive determination of four bisphenols is presented. The miniaturized technique was coupled with gas chromatography-mass spectrometry after derivatization by in situ acetylation. The Taguchi experimental method, an orthogonal array design, was applied to find the optimal combination of seven factors (each factor at three levels) influencing the emulsification, extraction and collection efficiency, namely acetic anhydride volume, sodium phosphate concentration, carbon tetrachloride volume, aqueous sample volume, sodium chloride concentration and ultrasound power and application time. A second factorial design was applied with four factors and five levels for each factor, 25 experiments being performed in this instance. The matrix effect was evaluated, and it was concluded that sample quantification can be done by calibration with aqueous standards. The detection limits ranged from 0.01 to 0.03 ng mL depending on the compound. The environmentally friendly sample pretreatment procedure was applied to study the migration of the bisphenols from different types of samples: thermal printer paper, compact discs, digital versatile discs, small tight-fitting waistcoats, baby's bottles, baby bottle nipples of different materials and children's toys. [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

In this opinion paper the toxicokinetic behaviour of arsenosugars is reviewed and compared with that of inorganic arsenic and arsenobetaine. It is concluded that the arsenosugars are similar to inorganic arsenic in terms of metabolite formation and tissue accumulation. As a pragmatic means of generating uniform data sets which adequately represent the toxicity of arsenic in food we recommend reporting partly speciated arsenic concentrations in food commodities in three fractions: i) toxic inorganic arsenic as arsenate (after oxidation); ii) arsenobetaine as established non-toxic arsenic; and iii) potentially toxic arsenic, which includes arsenosugars and other organoarsenicals. [ABSTRACT FROM AUTHOR]

The Arxula yeast bisphenol screen (A-YBS) utilizes the bioluminescent Arxula adeninivorans yeast–based reporter cells for tailored analysis of bisphenols, one of the major endocrine-disrupting compound groups. For the first time, this bioreporter has been applied on the high-performance thin-layer chromatography (HPTLC) adsorbent surface to develop a respective planar bioluminescence bioassay (pA-YBS). The goal was to combine the advantages of HPTLC with a more selective bioassay detection for bisphenols. The performance of this pA-YBS bioluminescence bioassay was demonstrated by calculating the half-maximal effective concentration (EC50) of bisphenols compared to references. The EC50 ranged from 267 pg/band for bisphenol Z and 322 pg/band for bisphenol A (BPA) to > 1 ng/band for other bisphenols (BPC, BPE, BPF, and BPS) and references (17β-estradiol and 17α-ethinylestradiol). The EC50 value of BPA was three times more sensitive in signal detection than that of 17β-estradiol. The visual or videodensitometric limit of detection of BPA was about 200 pg/zone. The higher signal intensity and sensitivity for BPA confirmed the tailored bioassay selectivity compared to the existing estrogen screen bioassay. It worked on different types of HPTLC silica gel plates. This HPTLC–UV/Vis/FLD–pA-YBS bioluminescence bioassay method was used to analyze complex mixtures such as six tin can migrates, five thermal papers, and eleven botanicals. The detected estrogenic compound zones in the tin can migrates were successfully verified via the duplex planar yeast antagonist estrogen screen (pYAES) bioassay. The two bisphenols A and S were identified in one out of five thermal papers and confirmed with high-resolution mass spectrometry. No bisphenols were detected in the botanicals investigated via the pA-YBS bioluminescence bioassay. However, the botanicals proved to contain phytoestrogens as detected via the pYAES bioassay, which confirmed the tailored bioassay selectivity. This HPTLC–UV/Vis/FLD–pA-YBS bioluminescence bioassay is suited for cost-efficient analysis of BPA in complex samples, with no need for sterile conditions due to the fast workflow. [ABSTRACT FROM AUTHOR]

The article discusses the history of dry chemistry in analytics. Topics mentioned include the use of strips containing a reagent pad which dipped in urine to determine protein and glucose, the development of spectrometric instrumentation in clinical chemistry and the integration of immunochromatographic technique in point-of-care diagnostics.

HIV prevention and treatment with injectable cabotegravir and/or rilpivirine administered once every 4 to 8 weeks is an attractive alternative to daily therapy. Prescribed dosage and drug concentrations in plasma are based on patient data collected in clinical trials, but actual patients are expected to exhibit more variability in drug concentrations, which is important to quantify. Here, we demonstrate the first quantitative point-of-care assay with a miniature mass spectrometer to assess these drug concentrations in whole blood. Quantitative performance is obtained using paper spray ionization in combination with tandem mass spectrometry (MS/MS) in the clinically relevant concentration range of both drugs. Limits of quantitation (LoQs) of cabotegravir and rilpivirine are measured to be 750 ng/mL and 20 ng/mL, respectively. The assay turnaround time is < 4 min, and strong linear relationships are established between MS/MS responses and concentration, with percentage of relative standard deviations (RSDs) that are <15% at concentrations above the LoQs. The speed, portability, low power consumption, and specificity offered by the miniature instrument should make it an appropriate platform for measuring drug concentrations in a walk-in clinic using small volumes of patient blood. [ABSTRACT FROM AUTHOR]

Bisphenol A (BPA) is an important industrial chemical used as a plasticizer in polycarbonate and epoxy resins in the plastic and paper industries. Because of its estrogenic properties, BPA has attracted increasing attention from many researchers. This review focuses primarily on analytical methods for BPA detection that have emerged in recent years. We present and discuss the advantages and disadvantages of sample preparation techniques (e.g., solvent extraction, solid-phase extraction, molecularly imprinted polymer solid-phase extraction, and micro-extraction techniques) and analytical methods (e.g., liquid chromatography, liquid chromatography−mass spectrometry, gas chromatography−mass spectrometry, capillary electrophoresis, immunoassay, and several novel sensors). We also discuss expected future developments for the detection of BPA. [ABSTRACT FROM AUTHOR]

An approach was developed for the preparation of cryogenic ground spiked filter papers with Cu and Zn for use as synthetic calibrating standards for direct solid microanalysis. Solid sampling graphite furnace atomic absorption spectrometry was used to evaluate the microhomogeneity and to check the applicability of the synthetic calibrating standards for the direct determination of Cu and Zn in vegetable certified reference materials. The found concentrations presented no statistical differences at the 95% confidence level. The homogeneity factors ranged from 2.7 to 4.2 for Cu and from 6.4 to 11.5 for Zn. [ABSTRACT FROM AUTHOR]

In this paper, a spectral collection of over 150 ATR-FT-IR spectra of materials related to cultural heritage and conservation science has been presented that have been measured in the extended region of 4000-80 cm (mid-IR and far-IR region). The applicability of the spectra and, in particular, the extended spectral range, for investigation of art-related materials is demonstrated on a case study. This collection of ATRFT-IR reference spectra is freely available online () and is meant to be a useful tool for researchers in the field of conservation and materials science. [ABSTRACT FROM AUTHOR]

Microfluidic immunoassay devices are a promising technology that can quickly detect biomarkers with high sensitivity. Recently, many studies implementing this technology on paper substrates have been proposed for improving cost and user-friendliness. However, these studies have identified problems with the large volume of sample required, low sensitivity, and a lack of quantitative accuracy and precision. In this paper, we report a novel structure implemented as a cellulosic material-based microchannel device capable of quantitative immunoassay using small sample volumes. We fabricated microfluidic channels between a transparent cellophane film and water-resistant paper to facilitate loading of small-volume samples and reagents, with a 40-μm-wide immunoreaction matrix constructed in the center of the microchannel using highly precise photolithography. A fluorescence sandwich immunoassay for C-reactive protein (CRP) was successfully implemented that required only a 1-μL sample volume and a 20-min reaction time. We confirmed that the limit of detection of the device was 10–20 ng/mL with a coefficient of variation under 5.6%, which is a performance level comparable to conventional plastic-based human CRP enzyme-linked immunosorbent assay (ELISA) kits. We expect that such devices will lead to the elimination of large amounts of medical waste from the use of ubiquitous diagnostics, a result that is consistent with environmental sustainability goals. [ABSTRACT FROM AUTHOR]

Certified reference materials (CRMs) are routinely used by analytical chemists to validate new analytical methods and to demonstrate the quality of their quantitative measurements. Even though CRMs for trace element and trace organic analysis have been available and widely used for over 50 years, the majority of papers published in analytical chemistry journals do not mention the use of CRMs. What if analytical/bioanalytical chemistry journals required the use of CRMs to publish a paper? This feature article attempts to address this question by providing examples of recent papers that have made exceptional use of CRMs to validate new analytical methods and to describe novel, alternative uses of CRMs that provide new characterization of the CRM. The potential benefits of using a CRM even when it does not have certified values for the analytes of interest are presented. [ABSTRACT FROM AUTHOR]

The reddish-brown, brown or yellowish stains of circular or irregular shape known as foxing spots have been fully described in conservation literature but still, this phenomenon does not find any scientific agreement since many hypotheses have been raised concerning their origin. In this work a contribution to foxing definition not only focussed on its appearance but also reported on its chemical information. For this purpose foxing stains present in drawings from two Portuguese artists dated from the eighteenth to nineteenth centuries were observed under ultra-violet light and optical microscope and analysed by three non-invasive spectroscopy techniques. The observations carried out on the stains provided information on their surface morphology. The use of energy-dispersive X-ray fluorescence revealed a variation on the elemental content between foxing and paper region. Although the results from X-ray diffraction analysis showed no signs of cellulose degradation in foxing stains, Fourier-transformed infrared analysis revealed the presence of oxide groups. Both the information on the chemical nature and surface morphology of the stains achieved in this study will contribute to increase foxing formation information and develop future protocols for conservation purposes. [ABSTRACT FROM AUTHOR]

Fast, simple, and low-cost on-site visualized detection of inorganic phosphate (Pi) is in great demand since phosphate is the major reason of eutrophication. In this work, a ratiometric fluorescent probe composed by green carbon dots (GCDs) and red carbon dots (RCDs) has been established for high-sensitivity and selective sensing of Pi. A trend of color change from red to green is observed for the detection of Pi under ultraviolet light and the detection limit is 0.09 μM in the range of 0 to 55 μM. Fluorescent test paper prepared from the probe solution was successfully applied to semi-quantitative visual detection of Pi in real-world water and soil samples, which shows great real-world application potentials. [ABSTRACT FROM AUTHOR]

A non-destructive and non-invasive method for quantitative characterization of parchment deterioration, based on spectral measurements, is proposed. Deterioration due to both natural aging (ancient parchments) and artificial aging (achieved by means of controlled UV irradiation and temperature treatment) was investigated. The effect of aging on parchment native fluorescence was correlated with its deterioration condition. Aging causes fluorescence intensity drop, spectral shift of the main peak, and an overall change in the fluorescence spectral features. Digital color imaging analysis based on visible reflectance from the parchment surface was also applied, and the correspondent color components (RGB) were successively correlated with the state of parchment deterioration/aging. The fluorescence and color imaging data were validated by analysis of historical parchments, aged between 50 and 2000 years and covering a large variety of states of deterioration. The samples were independently assessed by traditional microscopy methods. We conclude that the proposed optical method qualifies well as a non-destructive tool for rapid assessment of the stage of parchment deterioration. [ABSTRACT FROM AUTHOR]

A new family of coumarin-based pH indicators was synthesized. They are sensitive to pH in either weakly acidic or weakly basic solution. The indicators possess moderate to high brightness, excellent photostability and compatibility with light-emitting diodes. The indicators were covalently immobilized on the surface of amino-modified polymer microbeads which in turn were incorporated into a hydrogel matrix to obtain novel pH-sensitive materials. When a mixture of two different microbeads is used, the membranes are capable of optical pH sensing over a very wide range comparable to the dynamic range of the glass electrode (pH 1–11). [Figure not available: see fulltext.] [ABSTRACT FROM AUTHOR]

The article announces that Thomas Lummerstorfer has received the 2007 ABC Best Paper Award from "Springer."

Reports that chemist Christoph Meyer has won the 2005 Analytical and Bioanalytical Chemistry Best Paper Award. Overview of his paper on the high performance liquid chromatography (HPLC) separation abilities of novel polymer-based chromatographic reversed-phase stationary phases; Background on HPLC with nuclear magnetic resonance; His career and academic background.

Features Swedish physicist Martin Bengtsson, the first award winner of the "Analytical and Bioanalytical Chemistry" Best Paper Award in 2005. Background on his paper with Thomas Laurell entitled "Ultrasonic Agitation in Microchannels"; Discussion of the problem of laminar flow in microchannels; Educational background of Bengtsson.

An editorial is presented which discusses the role of certified reference material (CRM) for the validation of analytical methods and evaluation of comparability and accuracy of results in different laboratories. Topics discussed include the development of CRM, the publication of CRM papers by the journal "Analytical and Bioanalytical Chemistry," and the production of standard reference materials (SRMs).

The article features Andreas Römpp and Sabine Guenther, winners of the 2012 Best Paper Award for their work published in "Analytical and Bioanalytical Chemistry (ABC)." They focus on accurate mass-based identification of imaged compounds and on improving lateral resolution in biological tissue analysis to increase the validity and reliability of mass spectrometry (MS) images. An interview with Römpp and Guenther about their research, motivations, and about themselves is included.

The article focuses on Best Paper Award given to young scientists by the journal Analytical and Bioanalytical Chemistry (ABC). Created with the aim of encouraging exceptional young scientists in establishing their research careers, this Award will be presented annually to a scientist up to 40 years of age who is the lead author of a paper published in ABC during the calendar year. Selected by the editors, the winner will receive a prize of 1,000 Euro, sponsored by Springer. In addition, the winning paper will receive special prominence on an ABC cover. All research papers submitted to the journal by lead authors up to the age of 40 will be considered for this Award.