Search

Natural fibers have been extensively studied as a reinforcement filler in obtaining composites, replacing partially synthetic fibers. The vast majority of these materials originate from agro-industrial waste with a high content of lignin and cellulose making it a very interesting material with low cost and good mechanical properties. The purpose of the study was to obtain a composite based on alkyl ketene dimer resin, for the manufacture of sustainable packaging, made of paper by adding a 10% (w/w) con-tent of green coconut fiber and sugarcane bagasse fiber, and evaluated the impact of the filler on the mechanical behavior of the systems. The studied material was characterized from mechanical tests, such as Ring Crush Test (RCT) and Concora Medium Test (CMT) evaluating the maximum resistance supported by centimeter in the pre-pared composites, by the specimens. Through the RCT tests, with 10% w/w fibers, it was possible to verify that the fiber from sugarcane bagasse reached an increase of about 1% in the reinforcement effect compared to pure paper, and a difference of up to 2% in strength mechanics in relation to coir fiber, and CMT tests shows the reinforcement effect of the presence of sugarcane bagasse fiber, with an increase of about 3% compared to pure paper, and with a mechanical strength higher by 1% compared to coconut fiber. Therefore, the study was funneled with sugar cane fiber, varying the content by 20 and 30 % (w/w), evaluating the impact on the dispersion of this filler in the polymeric matrix and, consequently, the mechanical response of the composite with these compositions. The conclusion of the study was that the system prepared with 20% (w/w) was the one that achieved the greatest optimization of the mechanical properties, evaluated by the tests. This type of material can be applied to obtain cardboard boxes with resistance to high loads, due to the achievement of good mechanical properties.

Currently, paper pulping production from woody materials has many disadvantages due to its high energy, chemical, water consumption, methane emissions, and deforestation. However, the use of non-woody materials solves these problems. This study focused on the use of non-virgin raw material (Enset leaf fiber) in pulp and paper making. Enset leaf residues are the primary solid residues after the steam plant is used for “Kocho” processing. This leaf fiber has a lignocellulose component, converting this residue into Pulp and paper is crucial in terms of economic and waste management via the Kraft process. It has a higher fiber quality, lower energy consumption, and high recoverability of the chemical raw materials used in the process. The chemical composition of the Enset leaf fiber was analyzed using the Technical Association of Pulp and Paper. It has an excellent fiber length (2.12±1.46mm), fiber diameter (26.55±15.6µm) andacceptable rigidity coefficient (1.05±0.07), and flexibility coefficient (125.23±0.04). The maximum pulp yield was obtained at a temperature of 120°C, NaOH concentration of 8%, and 40 min cooking time off, which was 69.92% w/w. The functional groups of the Enset leaf fiber and morphological characteristics of the fiber were investigated.

The agriculture waste material can give benefit to many production industries. The studied crop is corn (Zea Mays)stalk. The objective of this work was to analysis the chemical composition; to study chemical pulping and papermaking properties of corn stalk and; to investigate the fiber morphology of properties of those crops. Firstly, the chemical composition of corn stalk were determined and compared with other non-woods. After that, chemical corn stalk was conducted in this analysis followed the physical and mechanical properties. The result showed that, corn stalk have cellulose (39.0%) and lignin content is the lowest (7.3%) content rather than other composition. In chemical pulping, reached high pulp yields had been produced and the strength properties: tear index, tensile index, burst and fold verified that they were of an acceptable quality for papermaking. This crop morphology was observed by Scanning Electron Microscopic (SEM), which showed a condensed composition of fiber structure. This study can developed a friendly product and promote the green technology, suitable to be used as an alternative pulp in paper making industry.Keywords:Fiber, Corn stalk, Composition, Green technology, Pulp and paper making.

The aim of this study was to study the morphology and structural characteristic of NCC hydrolyzed from filter paper. The NCCs were extracted by acid hydrolysis at 50°C for 1 hour, using 55% conc. H2SO4 under vigorous mechanical stirring, centrifugation at 12000 rpm in distillate water and followed by homogenizing at 7000 rpm. The morphology and surface profiles of the NCC suspension was characterized using field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). The crystalline structure of the NCC was evaluated by using X-ray diffraction (XRD) technique. As a result, hydrolysed NCC was found to have a rod liked shape with diameter in the range of 100-300nm length and 10-50nm width, with the aspect ratio value of 10.3 nm. According to XRD investigations, the semi-crystalline cellulose was observed with the presence of an amorphous broad hump and crystalline peaks at 2θ of 15o and 22.7o, respectively. The crystalinity index of the raw filter paper was calculated as 86.7 % and increased to 94.4 % as it was extracted to NCC. Crystallite size of raw filter paper and NCC was calculated as 20.6 nm and 11.4 nm, respectively

In this paper, Kevlar or Polysulfonamide (PSA) pulp were used to replace plant fiber pulp partially or completely and by adjusting their ratios and a variety of Kevlar or PSA pulp reinforced activated carbon fiber paper (ACFP) were prepared via wet-laid paper making technology. The influences of addition of Kevlar or PSA pulp on the permeability, mechanical property, filtration performance, adsorption property of ACFP were discussed by maintaining the addition content of activated carbon fiber unchanged. Results showed that with the addition content of Kevlar or PSA pulp increased, the permeability and filtration performance of ACFP decreased obviously, while the bursting strength and the static CCl4 adsorption performances were firstly increased and then decreased. Generally, the permeability and filtration performance of Kevlar pulp reinforced ACFP were slightly worse than that of PSA pulp reinforced ACFP, while the bursting strength as well as the static CCl4 adsorption properties of Kevlar pulp reinforced ACFP were better than that of PSA pulp reinforced ACFP.