Search

For a hygiene paper such as tissue and towel, strength, softness, and absorbency are known as attributes that a user is looking for. It is proposed here that purchasing decisions are likely to be influenced by in-use experiences, which may be quite different from the physical properties measured with current standardized tests. There have been continuous efforts on developing physical test methods to replace subjective in-use tests because the benefits of the former are too significant to be overlooked. This paper considered some in-use test methods for paper towel products that can be carried out by panel members quickly in the course of sensory panel testing. In addition, laboratory tests were developed in an attempt to quantify such input. The sensory panel testing showed that (wet) strength and absorbency were the key contributions to the performance of paper towels. Softness did not show any significant contribution to it. Wet strength showed a high correlation with absorbency. The (wet) ball burst strength had the highest correlation with the in-use strength. Although both the tensile strength and the ball burst strength had a high correlation with preference, the ball burst tester is preferred because more reproducible and simpler to operate.

The development of pesticides has significantly advanced global agricultural production, but the ensuing problem of pesticide residues poses a severe threat to human health. So, there is an urgent need to establish a rapid, accurate, sensitive, cost-effective and on-site method for large-scale detection of pesticide residues. Electrochemical paper-based analytical devices (ePADs) represents a highly sensitive and portable microanalysis system, which uses paper as a substrate and relies on a capillary force to drive the fluid for the separation and detection of samples. The diversity of pesticides and agricultural products and the complexity of matrices impose high requirements on the sample preparation procedure. This article summarizes the preparation process of ePADs from the aspects of paper selection, the establishment of hydrophilic and hydrophobic channels, the integration of separation zones, and electrode printing. Subsequently, this paper establishes the relationship between pesticide detection and chip preparation based on the mechanism of electrochemical detection of pesticides. Finally, it discusses the advantages, challenges and future prospects of ePADs with a view to providing theoretical reference for enhanced application of ePADs in the field of pesticide residue detection.

Abstract This study aims to characterise the so-called Sialkoti paper used to produce Pahari drawings preserved today in the Wereldmuseum in Leiden (Netherlands) (WML). These works originate from the Punjab Hills in India (today Himachal Pradesh) and are commonly known as ‘Pahari miniature paintings’. The paper upon which these drawings are executed is said to have been produced in Sialkot during the eighteenth and nineteenth centuries when papermaking was an integral part of an overall regional economy correlated with other sectors such as agriculture and the textile industry. Although the term Sialkoti refers to identified papermills in Sialkot (now Pakistan), the paper from this region is yet to be subjected to a systematic study. This article therefore explores the paper(s) in question through macro- and microscopic observations of structure, pulp and fibres. The study of historical sources, complemented by the analysis of paper samples and fibre identification, has revealed that the pulp would have been prepared from a variety of manufactured products using different technologies, such as rags, cloth, mats, rope and other plant-based materials made from local bast fibres which, once tattered, were recycled to prepare the pulp. Microscopic study reveals that a variety of fibre combinations under different conditions and processing steps were used, in particular sunn hemp fibre (Crotalaria juncea L.), a plant species that has until now rarely been identified in historical paper. In addition, the presence of kenaf and jute fibres, as well as a significant quantity of cotton fibres, have also been demonstrated. To overcome the lack of comparative materials, our work was supported by a comparative study of several materials made from sunn hemp now held in the Ethnobotany Collection at Kew Gardens. Samples were taken from these materials and provided useful reference micrographs for the identification of the WML samples. The quality of the paper used by Pahari artists, as well as the raw materials available and their processing, are discussed in detail. Putting all the data, including technical and historical information into perspective, we conclude that the Pahari artists used a paper of inferior quality compared to other types of paper used for other purposes such as the creation of illuminated manuscripts in the Punjab plains. This study therefore provides useful analytical and material evidence that complements previous historical, technical and anthropological studies.

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (three-ply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability.

Pretreated carboxymethylated nanofibrillated cellulose (CM-NFC) was tested as a strength enhancer for specialty paper, such as banknotes made from cotton linter mixed pulp (CLMP). The pretreatment agent was cationic poly(acrylamide) (C-PAM). The CM-CMF prototype was supplied by a Korean manufacturer. Laboratory tests and pilot trials were performed to evaluate the strength enhancement of banknotes incorporated with surface-modified CM-NFC and determine the process problems encountered in a pilot paper machine. The CM-NFC was surface modified with 0.1% C-PAM without any agglomerates. The prepared laboratory handsheets had high paper strength, which was attributed to the higher nanofibril content of surface-modified CM-NFC compared with that of unmodified CM-NFC. Pilot trials showed that the incorporation of 3% surface-modified CM-NFC was highly effective in promoting the strength of banknote without low retention and drainability on the wet-end part of the pilot paper machine. Therefore, surface-modified CM-NFC at a controlled dosage could be used as a strength enhancer for specialty paper without incurring serious problems in a paper mill.

Abstract The pulp and paper industry generates vast quantities of paper sludge, posing significant environmental challenges due to its disposal in landfills or incineration. This study explores the potential of valorizing paper sludge by incorporating it into particleboard production. It aims to optimize sludge content and particle size to enhance board properties—a novel approach to waste management in the wood composites industry. Through systematic variation of sludge content (0–25%) and particle size ( 2 mm), we assessed the mechanical and physical properties such as internal bond strength (IB), modulus of rupture (MOR), modulus of elasticity (MOE), water absorption (WA), and thickness swelling (TS). The findings indicate that incorporating paper sludge at moderate levels (5–15%) with optimized particle sizes (

Yang Xi,1,* Yu-Qin Deng,1,2,* Han-Da Li,1 Wo-Er Jiao,1 Jin Chen,2 Jian-Jun Chen,3 Ze-Zhang Tao1,2 1Department of Otolaryngology, Head and Neck Surgery, Renmin Hospital of Wuhan University, Wuhan, People’s Republic of China; 2Institute of Otolaryngology, Head and Neck Surgery, Renmin Hospital of Wuhan University, Wuhan, People’s Republic of China; 3Department of Otorhinolaryngology, Union Hospital, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, People’s Republic of China*These authors contributed equally to this workCorrespondence: Ze-Zhang Tao, Department of Otolaryngology, Head and Neck Surgery Renmin Hospital of Wuhan University, 238 Jie-Fang Road, Wuhan, 430060, Hubei, People’s Republic of China, Tel +86 13907141892, Fax +86 27 88043958, Email taozezhang696@163.com Jian-Jun Chen, Department of Otorhinolaryngology, Union Hospital, Tongji Medical College, Huazhong University of Science and Technology, 1277 Jiefang Avenue, Jianghan District, Wuhan, 430060, Hubei, People’s Republic of China, Tel +86 13659851719, +86 27 85726300, Email ylly80331@163.comPurpose: Up to now, there is no generally accepted biomarker to indicate the clinical response of immunotherapy. This study mainly analyzed the correlation between eosinophil cationic protein-myeloperoxidase (ECP-MPO) test papers and other immunotherapy indices in subcutaneous immunotherapy of dust mites and to explore whether the test paper can be used as an auxiliary index to quickly evaluate the efficacy of immunotherapy.Patients and methods: This study included 53 participants who received subcutaneous immunotherapy at the allergy clinic of Renmin Hospital of Wuhan University and 28 control participants. Six visits were conducted during a prospective study over one year. The results of the ECP-MPO test paper, nasal secretion eosinophil smear and count, nasal secretion ECP concentration, and clinical symptom scores were collected during five follow-up visits after the start of subcutaneous immunotherapy. Th1/Th2/Th17 cytokines, chemokines, IgE, IgG4 against dust mite components, and ECP concentrations were detected in the serum of participants at baseline, six months, and one year after subcutaneous immunotherapy.Results: The ECP test paper is not only easy to operate, but also can effectively and quickly detect the concentrations of ECP in the nasal secretion and diagnose allergic rhinitis. Symptom score is an important index for evaluating clinical immune efficacy, during subcutaneous immunotherapy, the ECP test paper showed a positive correlation with the symptom score. Simultaneously, during immunotherapy, the changes in the chromogenic grading of the test paper were synchronized with the changes in inflammatory cytokines and eosinophilic chemokines in Th2 cells of serum dust mite IgE. The sIgG4 against dust mites weakly negatively correlated with the concentration of ECP in nasal secretions and the color classification of the ECP test paper.Conclusion: The ECP-MPO test paper has a certain correlation with subcutaneous immunotherapy markers of allergic rhinitis, indicating that the ECP test paper may become an auxiliary biomarker to replace other complex laboratory tests.Keywords: dust mites, ECP-MPO test paper, subcutaneous immunotherapy, allergic rhinitis

Abstract The study was designed to explore the efficiency of magnetite nanoparticles (Fe3O4 NPs)/bacterial cell assembly to biodegrade lignin and lignocellulose, decontaminate pulp and paper-contaminated wastewater and optimize lignin adsorption by Fe3O4 NPs. Water samples were collected from three paper and carton manufacturing companies, Alexandria Governorate, Egypt. Pseudomonas otitidis MCC10330, the most active and promising strain among 10 previously screened indigenous and exogenous isolates, was selected and decorated with magnetic Fe3O4 Nanoparticles, that were prepared by the co-precipitation method, characterized and used to decontaminate paper and pulp effluent in a batch mode bioassay for 4 h. Fe3O4 NPs/bacterial cell assembly achieved the highest removals (64.1, 52.0, 54.3 and 66.6%) of TSS, COD, BOD, and Total Tannin and Lignin after 1, 4 and 4 h, reaching residual concentrations (RCs) of 322, 216, 112 and 7 mg/L, which are still slightly higher (5.35, 2.7 and 1.86-fold) than their maximum permissible limits (MPLs), respectively. RCs of pH, DO and TDS in the treated effluent are accepted for safe discharging. Maximum lignin adsorption and removal (82.14%) using Fe3O4 NPs was achieved at the optimized conditions (pH 6, Fe3O4 NPs dosage of 100 mg and 10 min contact time). Results confirmed that the proposed magnetite-coated Pseudomonas otitidis treatment system is highly efficient and recommended to treat the highly contaminated pulp and paper wastewater. Also, as far as we know, this integrated assemblage is the first time to be used as a novel, very promising, eco-friendly, renewable and economical biotechnological approach to minimize/eliminate the involved pollutants with the least running time.

Reducing the carbon footprint of higher education institutions has become a global trend in recent years, as they are the axis of society's scientific and technological transformation that must be carried out with a sustainable approach. Among the many approaches that can contribute to this problem are the digital transformation of academic and administrative processes and its impact on reducing paper use. This study details the statistical analysis of the digital transformation process based on the modules and computer services implemented by the ICT department in a higher education institution and its incidence in reducing the use of paper by its teaching and administrative staff. For this purpose, an initial instrument was proposed, consisting of 18 ordinal, three categorical and two numerical variables. After applying statistical data processing and validation techniques, it was reduced to 13 ordinal variables, three categorical and two influential numerical variables. In addition, this study has proposed an appropriate statistical protocol for the design and extraction of information applicable in the context of higher education institutions, consisting of the techniques: Mahalanobis distances, confirmatory factor analysis, Kruskal-Wallis, Mann-Whitney's U and Wilcoxon tests. The results showed the power of confirmatory factor analysis as a technique for obtaining models to measure indirectly observed latent variables, such as perceptions of digital transformation and paper reduction. In addition, it was found that the modules, systems, and computer tools implemented in the institution significantly reduced the execution times for performing administrative and teaching tasks in the institution, and significant differences were identified in the perception of digital transformation and reduction of paper use among staff.

Paper-based materials made from cellulose have been sought after as a sustainable and inexpensive packaging option. However, the porous structure and high hydrophilicity of paper-based materials result in inadequate water and oil repellency, as well as a limited water vapor barrier. In this work, lignin nanoparticles (LNPs) were prepared using a high-speed homogenizer, and subsequently coated on base paper along with cationic starch to enhance its multi-barrier performance to facilitate the packaging application. The LNPs obtained through such a facile process formed stable colloidal dispersion in water, which exhibited excellent interfacial compatibility with cationic starch. During the coating process, a highly adhesive emulsion consisting of cationic starch and LNPs were coated on the surface of base paper, imparting good hydrophobic properties to the paper. The resulting paper material exhibited good water resistance (Cobb value of 37.5 g m−2), high oil resistance (Kit rating 9) and tensile strength (48.93 MPa). The reduction in water vapor transmission rate (WVTR) exceeds sixfold. This study provides a new avenue for the application of lignin in high-barrier, fluorine-free, water-and oil-resistant packaging materials.

The increasing rates of illicit behaviors, particularly financial crimes, e.g., bank fraud and tax evasion, adversely affect national economies. In such cases, using nondestructive methods, scientists must evaluate relevant documents carefully to preserve their value as evidence. When forensic laboratories analyze paper as evidence, they typically investigate its origin and date of manufacture. If a document’s date is earlier than the earliest availability of the paper used in its creation, then this anachronism indicates that the document has been backdated. This study investigated weave marks and drainage marks for forensic purposes. Machine learning models for forensic document examination were developed and evaluated. The partial least squares discriminant analysis (PLS-DA), support vector machine (SVM), and artificial neural network (ANN) classification models achieved F1-scores of 0.903, 0.952, and 0.931, respectively. In addition, to enhance model effectiveness and construct a robust model, variables were selected using the VIP scores generated by the PLS-DA model. As a result, the SoftMax classifier in the ANN model maintained its performance with an F1-score of 0.951 even with a 50% reduction in the number of input variables.

Abstract The trail making test (TMT) is a commonly used tool for evaluating executive functions, and the activation of cerebral oxygenation in the prefrontal cortex (PFC) during the test can reflect the participation of executive function. This study aimed to compare the differences in cerebral oxygenation in the PFC between the computer- and paper-based versions of the TMT and provide a theoretical basis for the optimization and clinical application of the computer-based version. A total of 32 healthy adult participants completed the computer- and paper-based TMT Types A and B. Cerebral oxygenation changes in the PFC were monitored during the experiment using near-infrared spectroscopy. Moreover, average changes in oxyhemoglobin (Δoxy-Hb) levels at the baseline and during activation periods in different types of testing were compared and analyzed. The number of correct connections in the computer-based version Type B was less than that in the paper-based version Type B (p

Abstract Background Oil spills are widespread and can cause devastating environmental consequences. Rapid oil identification is critical to find the origin of the spill, monitor the environment, and lead to informed mitigation measures. The current standard methods in oil spill identification are precise and reliable, but require extensive sample preparation, long instrument runs, and time-consuming data processing. Direct analysis in real time time-of-flight mass spectrometry (DART-ToF MS) has been employed to screen for spilled petroleum oils, with results obtained in mere hours. The present study introduced an innovative, simple, and fast oil sampling method using hydrophobic filter paper and demonstrated its compatibility with DART-ToF MS analysis. Motor oils, jet fuels, marine diesels, crude oils, intermediate fuel oils, heavy fuel oils, and diluted bitumen were collected using the filter paper sampling method. Classification models were constructed from the spectral data by heat map inspection followed by principal component analysis (PCA) and discriminant analysis of principal components (DAPC). Oil slicks and weathered oil slicks were prepared from five oil types, and samples from each slick were collected using filter paper. Results The filter paper technique allowed for effective oil sampling and data acquisition by DART-ToF MS for diluted source oils, oil slicks and weathered oil slicks. Classification via the constructed DAPC models indicated that the DART-ToF MS instrument in tandem with filter paper sampling and multivariate statistics can accurately identify common oil types, with significant improvement of sample collection and turnaround time. Conclusions The promising classification results, simple sample collection, and rapid data analysis illustrate the potential use of hydrophobic filter paper and DART-ToF MS as tools in managing large scale oil spill emergency situations.

Abstract This research explores how paper and online assessments (OA) can affect EFL learners’ personal development variables such as self-esteem, mindfulness, demotivation, and language learning development. Sixty intermediate English as a foreign language (EFL) students participated in the current research and were randomly grouped into the experimental group (EG) and the control group (CG). Before the intervention, the data collection tools assessing language learners’ self-esteem, mindfulness, demotivation, and language learning development were administered as pre-tests to all the participants. Subsequently, the EG was taught all lessons of the coursebook, Top Notch 2, by utilizing OA while the CG was taught the identical lessons using a conventional (pen and paper) assessment. In the post-treatment phase, the two groups completed the post-tests on self-esteem mindfulness, demotivation, and language learning progress. The study demonstrated that the EG group outperformed the CG group on the four post-tests. The findings indicate that the intervention of OA significantly enhanced language learning outcomes and psychological well-being regarding the measured personal development variables. The enhanced efficacy in the EG group can be ascribed to the utilization of OA during the treatment phase, which has a beneficial effect on academic and personal development. This study also posits that integrating OA augments psychological engagement and language development among EFL learners. It highlights the implications of the results associating teaching EFL via OA with the observed personal development aspects and attributes them to effects of positive psychology.

The potential of paper and paperboard as fiber-based materials capable of replacing conventional polymer-based materials has been widely investigated and evaluated. Due to paper’s limited extensibility and inherent heterogeneity, local structural variations lead to unpredictable local mechanical behavior and instability during processing, such as mechanical forming. To gain a deeper understanding of the impact of mechanical behavior and heterogeneity on the paper forming process, the Finite Element Method (FEM) coupled with continuum modeling is being explored as a potential approach to enhance comprehension. To achieve this goal, utilizing experimentally derived material parameters alongside stochastic finite element methods allows for more precise modeling of material behavior, considering the local material properties. This work first introduces the approach of modeling heterogeneity or local material structure within continuum models, such as the Stochastic Finite Element Method (SFEM). A fundamental challenge lies in accurately measuring these local material properties. Experimental investigations are being conducted to numerically simulate mechanical behavior. An overview is provided of experimental methods for material characterization, as found in literature, with a specific focus on measuring local mechanical material structure. By doing so, it enables the characterization of the global material structure and mechanical behavior of paper and paperboard.

The mineralization of inorganic components in paper sludge offers potential for their re-use in various fields. This study synthesized carbonates based on the minerals present in paper sludge and aimed to investigate the control of particle size distribution and particle shape of the synthesized carbonates. First, the physicochemical and thermal properties of paper mill sludge and ash were evaluated using a spectrophotometer, XRF, and TGA. Paper sludge ash was obtained by incinerating the paper sludge, followed by a carbonation reaction using CO2 gas injection and pH neutralization to produce recycled fillers. The average particle size, crystal lattice structure, and morphology of the recycled fillers were analyzed using a particle size analyzer, XRD, and FE-SEM. The results indicate that the recycled filler produced from coating paper sludge exhibited similar brightness and morphology to conventional paper-based fillers, suggesting its potential to replace commercial PCC (Precipitated Calcium Carbonate). In contrast, the recycled filler manufactured using old corrugated container mill sludge was deemed unsuitable due to its low hydration activity.

Partial discharge at the oil-paper interface is one of the main reasons for the failure of oil-paper insulation in oil-immersed transformers. In this article, based on the numerical model of multi-branching streamer discharge, a multi-branching streamer discharge model in oil-paper insulation system is constructed by further considering the charge transport characteristics of oil-paper interface. The surface discharge characteristics under the influence of the dielectric constant ratio between natural ester insulating oil and insulating paper, and the spacing between needle electrode and paperboard are studied by finite element method, respectively. The results show that the distance between the needle electrode and the paperboard, and the dielectric constant ratio of insulating oil and insulating paper both significantly affect the streamer branching. The smaller the clearance between the needle electrode and paper-board is, the more serious the inhibition of streamer branches at the oil-paper interface is, which resulting in the streamers near the oil-paper interface are more significant effect on the propagation of the z-axis streamer. When the dielectric constant of the insulating oil is larger than that of the paperboard, the development and branching of the streamer in the oil will be more significant. On the contrary, the streamer is more likely to develop along the surface of the paperboard and accumulate charge at the oil-paper interface.

Advanced studies aim to produce highly competent graduates in areas like research and publication. These expectations necessitate research capabilities in graduate students. To assess doctoral students' research abilities and inform instruction, a research course evaluates them at the beginning of the term. Employing a descriptive design, this study investigated 21 individuals enrolled in an advanced research course during the second term of the academic year 2022-2023. Data were collected using an adapted instrument. The results indicated that doctoral students possessed moderate capabilities in writing a research proposal. However, they reported feeling neutral regarding their ability to write publishable papers. Additionally, these individuals indicated a slight or limited capability for utilizing multivariate statistics. These findings hold implications for instruction and future research, particularly in prioritizing course content to address areas where doctoral students have limited research capabilities.

This study focuses on the elimination of residual dyes from industrial wastewater using talc as an adsorbent. Talc is an easily available, ecological, and inexpensive adsorbent. The adsorption process was tested on two model dye samples (Ecozol Blue LR Liquid and Cartasol Yellow 3GF Direct Yellow 132), and two samples of real wastewater from the pulp and paper industry (PM and TP). Kinetic studies revealed that the adsorption of Ecozol Blue LR Liquid followed pseudo-second-order kinetics, while the other tested samples followed pseudo-first-order kinetics. Langmuir, Freundlich, and Dubinin-Radushkevich adsorption isotherm models were also evaluated. The Langmuir isotherm model best fitted the experimental data for the adsorption of model dye solutions and wastewater sample TP onto talc. For wastewater sample PM, the Dubinin-Radushkevich isotherm model provided the best fit to the experimental data. The results of the adsorption isotherms indicated that the adsorption of all tested systems was favorable and primarily involved physical adsorption. The adsorption efficiency for the model solutions exceeded 90 %. For real wastewater samples, the monitored adsorption efficiency in the COD pollution indicator was less efficient, ranging from 43 to 51 %. The lower efficiency of COD may have resulted from the adsorption of residual dyes with lower specific COD values before the adsorption of other organics.

Recycling leather waste, which accumulates in large quantities in tanneries, and producing packaging paper with improved properties reduces the environmental burden and is at the same time economically efficient. A modified fibrous mass of waste from tanned and untanned leather scraps, waste paper, and acrylic emulsion was obtained and packaging paper based on them was produced. Alkaline modification of tanned leather waste - chrome shavings - leads to an increase in the electrokinetic potential and, accordingly, the stability of the fibrous suspension, partial hydrolysis of skin collagen occurs with the formation of new polar groups, and at the same time, the degree of cross-linking of the skin increases. In the paper composition, new intermolecular bonds are formed between cellulose and skin collagen. The microstructure, elemental composition, morphology, thermal and physical-mechanical properties of modified chrome shavings and composite paper were determined. A significant improvement has been achieved in the main parameters of paper: surface density (decrease by 16-25%), breaking load and breaking length (increase by 15-23%), number of double bends (increase by 2-6 times) in comparison with paper obtained from pure waste paper, and also to a greater extent compared to paper obtained from unmodified leather waste.

This study presents an innovative lateral flow microfluidic paper-based analytical device (μPAD) designed for conducting quantitative paper-based enzyme-linked immunosorbent assays (p-ELISA), seamlessly executing conventional ELISA steps in a paper-based format. The p-ELISA device utilizes a passive fluidic circuit with functional elements such as a multi-bi-material cantilever (B-MaC) assembly, delay channels, and a buffer zone, all enclosed within housing for autonomous, sequential loading of critical reagents onto the detection zone. This novel approach not only demonstrates a rapid assay completion time of under 30 min, but also boasts reduced reagent requirements, minimal equipment needs, and broad applicability across clinical diagnostics and environmental surveillance. Through detailed descriptions of the design, materials, and fabrication methods for the multi-directional flow assay (MDFA), this manuscript highlights the device’s potential for complex biochemical analyses in a user-friendly and versatile format. Analytical performance evaluation, including a limit of detection (LOD) of 8.4 pM for Rabbit IgG, benchmarks the device’s efficacy compared to existing p-ELISA methodologies. This pioneering work lays the groundwork for future advancements in autonomous diagnostics, aiming to enhance global health outcomes through accessible and reliable testing solutions.

Abstract Renewable materials and material circularity are key priorities for the coming decades. While paper is the most utilized material in the packaging sector, its applications in food packaging are limited due to low barrier properties. Coating it with petroleum-based polymer barrier coatings renders it unrecyclable both mechanically and biologically. Bio-coated paper packaging, made from agricultural waste or by-products, presents environmentally favorable solutions that can benefit the biological cycle of the circular economy. The main objective of this study is to assess the applicability of grain and beer production by-products in wood pulp food packaging materials. It examines the effects of different grain by-products (industrial wheat grain processing residues and wheat bran) particles and concentrations (15 wt% and 40 wt%), as well as the impact of brewer’s yeast (Saccharomyces cerevisiae) at a concentration of 10 wt%, on the physical–mechanical and barrier properties of Northern bleached softwood kraft (NBSK) and chemithermomechanical (CTMP) pulps. Material composites were fabricated using a standard sheet forming method. Physical–mechanical properties were analyzed through tensile strength, strain at break, tear resistance, and bending stiffness tests. Barrier-related properties were analyzed through roughness, air permeance, and water contact angle tests. Results revealed that the vast majority of physical–mechanical properties decreased with the increase of both types of grain production fillers. Industrial wheat grain processing residues had a lower impact on physical–mechanical properties than wheat bran filler. A higher percentage of property decrease was absorbed in NBSK pulp than in CTMP. Roughness of CTMP can be improved by adding both industrial wheat grain processing residues and wheat bran. Wheat bran particles can increase hydrophobicity. CTMP pulp strength properties can be increased with the addition of yeast; however, the yeast additive’s effect on air permeance demonstrated a negative impact. In the case of NBSK pulp, which has higher primary strength properties, the addition of yeast does not make any significant changes. The conducted experiments demonstrated that, overall, the addition of these fillers resulted in a decline in physical–mechanical properties such as tensile strength, strain at break, tear resistance, and bending stiffness. This decline was more pronounced with higher concentrations of fillers. In the case of CTMP pulp, both types of fillers exhibited similar trends in affecting properties, whereas for NBSK pulp, wheat bran had a more significant impact compared to wheat grain processing residues. The addition of yeast generally led to a reduction in physical–mechanical properties, particularly in tensile strength and tear resistance. However, samples containing yeast displayed increased flexibility compared to controls. The influence on barrier properties varied: while yeast increased air permeability, it also enhanced surface hydrophobicity, thereby reducing the paper’s receptivity to liquids.

This article presents the information on the valorization of waste generated during the production of tissue paper. The possibility of bioconversion of the polysaccharide part of paper sludge into simple sugars has been evaluated. The options for processing the paper sludge before enzymic hydrolysis to achieve the maximum yield of monosaccharides have been considered. Pretreatment with acids has been found to be a key step before the biocatalytic cleavage of waste polysaccharides. An additional yield of enzymic hydrolysis products after pretreatment with acids has been obtained by pre-extraction of the paper sludge with spirit or acetone. It has been established that the most intense enzymic hydrolysis of readily available fractions of the paper sludge takes place in the first 10–12 hours. Further, the process slows down, probably due to the action of the remaining components of the fillers, as well as an increase in the proportion of the difficult-to-hydrolyze polysaccharide part. In all cases, the proportion of absolutely dry non-hydrolyzed residue has been about 43±2 % of the dry matter of the paper sludge. The main products of enzymic hydrolysis have been glucose and xylose. The resulting sugars have been used for mixotrophic cultivation of the Tetradesmus obliquus and Chlorella vulgaris algae. Yeast strains have been selected for the conversion of monosaccharides from the paper sludge. In a series of experiments on non-sterile yeast cultivation, the Candida utilis PAL D and Debaryomyces hansenii SWING R cultures have turned out to be the most productive (within 2.10±0.14 g of air-dry yeast weight/dm3 per 24 hours). The degree of conversion of hydrolysate sugars has been 70±2 %. Most of the remaining sugars (about 80 %) have been represented by xylose. Complete utilization of the sugars has taken place on the 2nd day when having added an extra nitrogen source to the medium. On the other hand, the spent nutrient medium after yeast separation has been suitable for mixotrophic cultivation of microalgae. It has been revealed that the economic costs of pre-treatment of the paper sludge with nitric acid can be leveled by using the resulting salts as a nitrogen source for cultivating yeast. In doing so, the yield of yeast biomass increases by almost 2 times.

The purpose of the paper is to present the issues relating to methods of transport and commercial process management and support in logistics. Moreover, it will describe shipping actions in relation to the conflicts in Europe and worldwide. The study follows the work plan described as follows: The first chapter comprises an overview, logistics function, and classification of strategies in a logistics project. The second chapter includes information about the review and selection of methods of logistics project management. The third chapter pertains to the application of solutions restoring an old form of value stream mapping, known as the brown book exercise or the brown paper method. The fourth chapter refers to the aspects and solutions used in logistics project management in the hard times of logistic service market operations. Finally, the fifth chapter specifies the forms of trust management as the methods supporting logistics project management.

Abstract Nucleic acid amplification testing has great potential for point-of-need diagnostic testing with high detection sensitivity and specificity. Current sample preparation is limited by a tedious workflow requiring multiple steps, reagents and instrumentation, hampering nucleic acid testing at point of need. In this study, we present the use of mixed cellulose ester (MCE) paper for DNA binding by ionic interaction under molecular crowding conditions and fluid transport by wicking. The poly(ethylene) glycol-based (PEG) reagent simultaneously provides the high pH for alkaline lysis and crowding effects for ionic binding of the DNA under high salt conditions. In this study, we introduce Paper-based Abridged Solid-Phase Extraction with Alkaline Poly(ethylene) Glycol Lysis (PASAP). The anionic mixed cellulose ester (MCE) paper is used as solid phase and allows for fluid transport by wicking, eliminating the need for pipetting skills and the use of a magnet to retain beads. Following the release of DNA from the cells due to the lytic activity of the PASAP solution, the DNA binds to the anionic surface of the MCE paper, concentrating at the bottom while the sample matrix is transported towards the top by wicking. The paper was washed by dipping it in 40% isopropanol for 10 s. After air-drying for 30 s, the bottom section of the paper (3 mm × 4 mm) was snapped off using the cap of a PCR tube and immersed in the colourimetric loop-mediated isothermal amplification (cLAMP) solution for direct amplification and colourimetric detection. The total sample processing was completed in 15 min and ready for amplification. cLAMP enabled the detection of 102 CFU/mL of Escherichia coli (E. coli) from culture media and the detection of E. coli in milk

Abstract Paper bookbindings have been disregarded for centuries by scholars since they were only considered temporary covering materials for manuscripts and books. Recently, there is a willingness to reconsider these bindings and to evaluate their role. Thanks to the collaboration with the Marciana National Library in Venice, which stores an impressive collection of 849 detached bindings, the current research provides a chemical-physical elucidation about the composition and the manufacture of paper bookbindings realized between the 16th and the eighteenth century in the Venetian area. A selection of bookbindings was analysed by the means of complementary methods (thickness measurements, Attenuated Total Reflection—Fourier-Transform Infrared Spectroscopy (ATR-FTIR), Pyrolysis–Gas Chromatography–Mass Spectrometry (Py-GC–MS) and X-Ray Fluorescence (XRF)). Data evidence the presence of cellulose as the main component of paper pulp; hemicellulose and lignin were identified too, probably related to the presence of linen/hemp rags in the paper production. Gelatine was detected muck likely related to paper sizing; among inorganic additives CaCO3 was found in all samples. The presence of waxy material may be due to past undocumented conservation treatments.

Sai-Hong Ignatius Ou,1 Xiuning Le,2 Misako Nagasaka,1 Thanyanan Reungwetwattana,3 Myung-Ju Ahn,4 Darren WT Lim,5 Edgardo S Santos,6 Elaine Shum,7 Sally CM Lau,7 Jii Bum Lee,8 Antonio Calles,9 Fengying Wu,10 Gilberto Lopes,11 Virote Sriuranpong,12 Junko Tanizaki,13 Hidehito Horinouchi,14 Marina C Garassino,15 Sanjay Popat,16 Benjamin Besse,17 Rafael Rosell,18 Ross A Soo19 1University of California Irvine School of Medicine, Chao Family Comprehensive Cancer Center, Orange, CA, USA; 2University of Texas MD Anderson Cancer Center, Houston, TX, USA; 3Division of Medical Oncology, Department of Medicine, Faculty of Medicine, Ramathibodi Hospital, Mahidol University, Bangkok, Thailand; 4Department of Hematology and Oncology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul, Republic of Korea; 5Duke-NUS School of medicine, National Cancer Center Singapore, Republic of Singapore; 6Charles E. Schmidt College of Medicine, Florida Atlantic University, Boca Raton, FL, 33431, USA; 7NYU Langone Perlmutter Cancer Center, NY, NY, USA; 8Yonsei Cancer Center Yonsei University, Seoul, Republic of Korea; 9Department of Medicine, Division of Medical Oncology, Early Drug Development and Phase I Unit, Hospital General Universitario Gregorio Marañón, Madrid, 28007, Spain; 10Shanghai Chest hospital, Tongji University School of Medicine, Shanghai, People’s Republic of China; 11Department of Medicine, Division of Medical Oncology, Sylvester Comprehensive Cancer Center at the University of Miami and the Miller School of Medicine, Miami, FL, 33136, USA; 12Chulalongkorn University, King Chulalongkorn Memorial Hospital, Bangkok, Thailand; 13Department of Medicine, Kindai University School of Medicine, Osaka, Japan; 14Department of Thoracic Oncology, National Cancer Center Hospital Tokyo, Tokyo, Japan; 15Department of Medicine, Division of Medical Oncology-Hematology, University of Chicago Medicine, Chicago, IL, USA; 16Royal Marsden Hospital, London, Imperial College, London, UK; 17Gustave Roussy Cancer Campus, Villejuif, France; Paris-Saclay University, Orsay, France; 18Department of Hematology-Oncology, National University Cancer Institute, National University Hospital Singapore, Republic of Singapore; 19IOR, Quirón-Dexeus University Institute; ICO, Catalan Institute of Oncology; IGTP, Germans Trias i Pujol Research Institute, Barcelona, SpainCorrespondence: Sai-Hong Ignatius Ou, University of California School of Medicine, Department of Medicine, Division of Hematology-Oncology, Chao Family Comprehensive Cancer Center, 200 South Manchester Avenue, Suite 400, Orange, CA, 92868, USA, Tel +1 714-456-5153, Fax +1 714-456-2242, Email Siou@hs.uci.eduAbstract: The year 2024 is the 20th anniversary of the discovery of activating epidermal growth factor receptor (EGFR) mutations in non-small cell lung cancer (NSCLC). Since then, tremendous advances have been made in the treatment of NSCLC based on this discovery. Some of these studies have led to seismic changes in the concept of oncology research and spurred treatment advances beyond NSCLC, leading to a current true era of precision oncology for all solid tumors. We now routinely molecularly profile all tumor types and even plasma samples of patients with NSCLC for multiple actionable driver mutations, independent of patient clinical characteristics nor is profiling limited to the advanced incurable stage. We are increasingly monitoring treatment responses and detecting resistance to targeted therapy by using plasma genotyping. Furthermore, we are now profiling early-stage NSCLC for appropriate adjuvant targeted treatment leading to an eventual potential “cure” in early-stage EGFR+ NSCLC which have societal implication on implementing lung cancer screening in never-smokers as most EGFR+ NSCLC patients are never-smokers. All these advances were unfathomable in 2004 when the five papers that described “discoveries” of activating EGFR mutations (del19, L858R, exon 20 insertions, and “uncommon” mutations) were published. To commemorate this 20th anniversary, we assembled a global panel of thoracic medical oncology experts to select the top 20 papers (publications or congress presentation) from the 20 years since this seminal discovery with December 31, 2023 as the cutoff date for inclusion of papers to be voted on. Papers ranked 21 to 30 were considered “honorable mention” and also annotated. Our objective is that these 30 papers with their annotations about their impact and even all the ranked papers will serve as “syllabus” for the education of future thoracic oncology trainees. Finally, we mentioned potential practice-changing clinical trials to be reported. One of them, LAURA was published online on June 2, 2024 was not included in the list of papers to be voted on but will surely be highly ranked if this consensus survery is performed again on the 25th anniversay of the discovery EGFR mutations (i.e. top 25 papers on the 25 years since the discovery of activating EGFR mutations).Keywords: EGFR mutations, expert panel, top 20 papers, 20th anniversary, NSCLC

As a way to reduce microplastics or nano-plastics in the ocean, it is of interest to develop biodegradable paper-based drinking straws to replace non-degradable plastic drinking straws. Primary questions to be addressed include how to design suitable coatings for paper drinking straws. Such coatings not only need to resist water. In addition, consumers have high expectations for the strength of a drinking straw. It is proposed here to replace non-biodegradable polypropylene, which is presently the main component of straws, with biodegradable and hydrophobic coating components via an entropy-driven approach. It is further proposed to develop colored paper-based drinking straws with cellulose nematic liquid crystal photonic pigments as a way to make the product stand out visibly, while at the same time mediating the usage of toxic chemical pigments.

Grease-proof paper is an energy-demanding paper product to manufacture, especially during refining and dewatering. Increases in energy efficiency in either stage could result in major savings. This article investigates the potential gains with addition of a stepwise progression vacuum suction box to the forming section during production. For both a lighter, 50 g/m2, and a heavier paper grade, 100 g/m2, with a pulp-drainability of 86 °SR, a stepwise progression vacuum suction box in four steps would result in increased dryness, simultaneously with decreased energy expenditure. The observed effects were higher for the lower basis weight paper (50 g/m2). Both basis weights experienced clogging of the forming fabric due to the high degree of refining. This adversely affected the dewatering rate, decreasing the amount of air pulled through the paper even when increasing the vacuum pressure. When a stepwise progression suction box in four steps was compared to a single vacuum suction box, there was a 14% increase in dryness for lighter paper, over an equal energy consumption, measured as amount of air pulled through the paper. For the 100 g/m2 paper, the increase in dryness was 3% compared to the 50 g/m2 paper run over a single vacuum suction box. The results show great promise for energy savings when utilizing stepwise progression suction box dewatering for grease-proof paper production.

A smooth and dense surface of the base paper is advantageous when the goal is to apply a liquid coating as a barrier layer. For such a base paper, non-wood fibers derived from wheat straw could be an alternative to wood fibers. In this research paper, wheat straw pulp was refined with different beating levels (up to 600 revolutions) followed by different calendering pressure loads (up to 50 N/mm) to test its influence on mechanical and surface properties. Alkyl ketene dimer (AKD) was used as sizing agent with concentrations up to 0.2 wt% followed by a mineral-based precoating to test its influence on the smoothness. Eucalyptus pulp was chosen as a benchmark. After beating, the initial Schopper-Riegler degrees of 28 °SR increased to 56 °SR. Beating also increased the tensile index from 24 to 49 Nm/g, the burst index from 1.2 to 2.8 kPa·m²/g, and the tear index decreased from 3.3 to 2.8 mN·m2/g. Calendering reduced the initial roughness of 370 mL/min to 30 mL/min. When precoated and calendered again, the value was lowered to 15 mL/min. In summary, wheat straw paper is a relevant alternative to wood-derived base paper to produce barrier papers. Compared to eucalyptus, wheat straw paper showed better smoothness and much lower air permeability indicating excellent suitability for barrier coating.

Paper mulching films are affected by wind and rain in the field, which lead to the problems of water absorption, shrinkage, and friction with the soil surface. In order to achieve better hydrophobic durability and wear resistance of paper mulching films, a paper mulching film with ZnO/SiO2 composite coating was prepared by the brush coating method. Taking ceramic balls as friction pairs, reciprocating friction tests were carried out with two kinds of paper mulching films at different temperatures. The morphology of the raw paper mulch film and the ZnO/SiO2 composite-coated paper mulch film after rubbing at different temperatures and the reason of the hydrophobic durability of the coated paper mulch film were analyzed using a scanning electron microscope and a three-dimensional topography instrument. The results show that ZnO/SiO2 composite coating can improve the wear resistance and hydrophobic durability of the paper mulch film. Through surface morphology analysis, it can be found that the composite coating plays a role in modification and filling and improves the adhesion between the fibers by reducing the pores on the surface of the paper mulch film, finally improving the wear resistance and hydrophobic durability of the paper mulch film.

The objective of this study was to assess, through simulation, conductivity variations in pulp and paper circuits when recycling waste water treatment plant (WWTP) effluent with a view to reducing fresh water use in a tissue mill. WWTP effluent was recycled in the process for different uses. A PS2000 digital model coupled with the PHREEQC chemical simulation engine was used to identify and quantify the main sources of conductivity: caustic soda, sodium bisulphite and acetate production through anaerobic microbial activity. Recycling WWTP effluent enables fresh water uptake to be reduced by 50% when used for pulp dilution or white water, by 81% when used in paper machine showers, and up to 96% for all uses combined. As fresh water use decreases, circuit closure increases along with, consequently, COD and conductivity. COD build-up can be controlled by best available techniques application. Recycling WWTP effluent has a strong impact on conductivity. However, the impact of high conductivity levels on additives performance is limited in the case of the mill studied. Acetate concentration could be controlled by better agitation of tanks or the introduction of air by pumps. Furthermore, limiting acetate production can reduce the need for caustic soda to control the pH. HIGHLIGHTS Modelling conductivity in pulp and paper mills.; Reuse in pulp and paper mills.; Reduction of fresh water consumption.; Anticipating discharge quality.; Reduction of chemicals uses.;

Abstract In the process of conservation mounting, starch paste made from wheat flour is the glue of choice to paste reinforcing strips and backing papers, often Xuan paper, for mending and decorating aged and damaged paper-based Chinese artworks. To keep objects intact and select appropriate conservation materials, this research explored the applicability of near-infrared (NIR) spectroscopy coupled with multivariate analysis for the characterization of contemporary unsized Xuan paper with and without starch. In particular, partial least squares (PLS) regression was used to predict the degree of polymerization (DP) of the paper, i.e., one of the most important properties of paper materials, and principal component analysis (PCA) was used to detect starch and to distinguish between papers with different amounts of starch. Using 12 contemporary unsized Xuan papers, the NIR-PLS method for DP prediction was validated, and the best-performed model was generated using the logarithmic transformation of DP−1 as a response variable, with root mean square error of prediction (RMSEP) of DP 128. The NIR-PCA method was also found to be applicable to separate starch-free papers and papers treated with starch, and the results indicate that the higher the content of starch, the better PCA classification performs. This research provides supporting data for the non-destructive characterization of Xuan paper-based objects and differentiates between Xuan paper before and after treatment with starch.

Oil-immersed power transformer is an important part of power grid, and its reliable operation plays a vital role in pomler system security. Aiming at the problem that the insulation state of transformer cannot be assessed quantitatively after long-term operation, the accelerated aging and damp tests of oil-paper insulation model are carried out in this paper. The influence of aging and damp of oil-paper insulation on its recovery voltage curves is explored. The particle swarm optimization (PSO) is used to improve the parameter prediction method of extreme learning machine (ELM), which realizes the quantitative assessment of aging and moisture of oil-paper insulation based on the characteristic parameters of the recovery voltage curve. By comparing the physical and chemical performance analysis of oil-paper insulation models, it is shown that the prediction accuracy of PSO-ELM method is much higher than that of traditional ELM method. The absolute error range for predicting the moisture content of oil-paper insulation the degree of polymerization (DP) of pressboard is less than ±0.4% or ±30, respectively.

Abstract Purpose Paper-based artifacts hold significant cultural and social values. However, paper is intrinsically fragile to microorganisms, such as mold, due to its cellulose composition, which can serve as a microorganisms’ nutrient source. Mold not only can damage papers’ structural integrity and pose significant challenges to conservation works but also may subject individuals attending the contaminated artifacts to health risks. Current approaches for strain identification usually require extensive training, prolonged time for analysis, expensive operation costs, and higher risks of secondary damage due to sampling. Thus, in current conservation practices with mold-contaminated artifacts, little pre-screening or strain identification was performed before mold removal, and the cleaning techniques are usually broad-spectrum rather than strain-specific. With deep learning showing promising applications across various domains, this study investigated the feasibility of using a convolutional neural network (CNN) for fast in-situ recognition and classification of mold on paper. Methods Molds were first non-invasively sampled from ancient Xuan Paper-based Chinese books from the Qing and Ming dynasties. Strains were identified using molecular biology methods and the four most prevalent strains were inoculated on Xuan paper to create mockups for image collection. Microscopic images of the molds as well as their stains situated on paper were collected using a compound microscope and commercial microscope lens for cell phone cameras, which were then used for training CNN models with a transfer learning scheme to perform the classification of mold. To enable involvement and contribution from the research community, a web interface that actuates the process while providing interactive features for users to learn about the information of the classified strain was constructed. Moreover, a feedback functionality in the web interface was embedded for catching potential classification errors, adding additional training images, or introducing new strains, all to refine the generalizability and robustness of the model. Results & Conclusion In the study, we have constructed a suite of high-confidence classification CNN models for the diagnostic process for mold contamination in conservation. At the same time, a web interface was constructed that allows recurrently refining the model with human feedback through engaging the research community. Overall, the proposed framework opens new avenues for effective and timely identification of mold, thus enabling proactive and targeted mold remediation strategies in conservation.

Abstract The paper industry is a major environmental polluter due to paper waste sludge (PWS), often disposed of in hazardous ways. The techniques are employed to disposing of PWS are posing significant environmental hazards and risks to well-being. This study aims to evaluate PWS as a potential replacement for commercial adsorbents like AC and ZEO in treating stabilized leachate. Contact angle analysis of PWS was 92.60°, reveals that PWS to be hydrophobic. Batch adsorption experiments were conducted with parameters set at 200 rpm stirring speed, 120 min contact time, and pH 7. Optimal conditions for COD and NH3–N removal were identified at 120 min contact time, 200 rpm stirring speed, pH 7, and 2.0 g PWS ratio. Removal percentages for COD and NH3–N were 62% and 52%, respectively. Based on the results of the isotherm and kinetic studies, it was observed that the Langmuir and Pseudo second order (PSO) model exhibited greater suitability compared to the Freundlich and Pseudo first order (PFO) model, as indicated by higher values of R-squared (R2). The R-squared of Langmuir for COD and NH3–N were 0.9949 and 0.9919 and for Freundlich model were 0.9855 and 0.9828 respectively. Whereas the R-squared of PFO for COD and NH3–N were 0.9875 and 0.8883 and for PSO were 0.9987 and 0.9909 respectively.

This research was designed to assess the yield and quality of ash prepared from different types of waste papers. Waste newspapers, writing papers, and cartons were selected for combustion to obtain the ashes and coded as WNPA, WWPA, and WCPA, respectively. The waste papers were incinerated simultaneously in separate but identical incinerators at 850 ℃. An experiment on the yield of the ashes was performed on two days before the ashes obtained were mixed based on the type of waste papers from which they were derived. The results showed that irrespective of the day and time, the WCPA was the most yielded (14.1%), followed by the WWPA (12.3%), and then the WNPA (11.9%). Also, it was found that all the ashes possessed flow properties acceptable for engineering applications. However, the WCPA would ensure the best performance if applied, especially as a partial replacement material for cement. While the WWPA was found to be richer than the WNPA, the WCPA was the richest in terms of the proportions of key oxides for strength development. In general, the percentages of various chemical components of each ash complied with the standard specifications for cement except in the case of losses on ignition of the WNPA and WWPA, which were about 0.53% and 0.02%, respectively, beyond the maximum stipulated value.

Abstract To compare the urine Congo‐red dot paper test (CRD) with dipstick urinalysis to screen preeclampsia (PE). A total of 409 paired spot urine samples were obtained prospectively from women with suspected pre‐eclampsia attending for routine hospital visits. Congo‐red dot paper test and dipstick urinalysis were examined and compared to screen pre‐eclampsia. The agreement between the two urinary test is modest (kappa coefficient = 0.28, 95% CI 0.14–0.42). The specificity of CRD was higher than urinalysis (97.4% vs. 90.4%, p

Contemporary ESL education focuses on screen-based reading, specifically in the context of university level learners. Also, a sudden shift from paper bound reading activities to screen-based tasks was inevitable in response to COVID-19 outbreak. In this regard, the case of inferential and advanced level reading among the young ESL learners of developing countries appears researchable because of the general low digital literacy of these learners. This study, therefore, aimed to investigate the effect of reading mode shift from paper to screen on the inferential comprehension performance among Pakistani ESL learners at university level. A total of 426 undergraduate learners were sampled from Bachelor of Science program in a well-known university in the city of Lahore, Pakistan. Inferential reading was conceptualized through Bloom’s higher order thinking skills, that is, Analyzing, Evaluating and Creating skills therefore the reading comprehension test was based on these skills. Adopting sequential test administration, first the paper-based reading test, and later the screen-based reading was given. The obtained data were analyzed using Rendell’s XCALIBRE and SPSS V. 26.0. The logit scale descriptives, learner ability (θ), and mean scores demonstrated that the learners performed significantly higher in the paper test as compared to screen test. Moreover, it was found that the effect of reading mode shift was larger in Creating skill. The findings may have significant implications for reading mode selection, enhancement of digital competence and effect of reading mode shift in developing countries with inadequate IT facilitation and digital literacy among ESL learners.

The present study was conducted to draw the co-authorship network of hot papers of science citation index in the Web of Science (WOS) database from 2020 to 2021. This investigation is a descriptive study using a scientometrics approach. This research was conducted using social network analysis indices to visualize the co-authorship networks of hot papers in the science citation index. The structure of the co-authorship network of researchers of hot papers in the field of science consists of 47,045 authors who have contributed to the publication of 3475 hot papers from 2020 to 2021, which indicates the high co-authorship of these authors. Moreover, it was found that among the co-authorship patterns of these researchers, the most significant number of articles during the studied years was related to the five-author collaborations. Moreover, the average Collaboration Coefficient (CC) of the authors of hot papers was higher than 0.80, indicating the authors' strong tendency to produce joint articles. The high collaboration of the authors of hot papers in the science citation index can be one of the reasons for increasing the level of visibility and the potential for using them.

Reliable data on U.S. paper and cardboard waste by location and type are critical for developing waste-reduction solutions, but detailed geographic analysis is lacking in the literature. In this study, we employ statistical and geospatial methods to assess paper and cardboard waste in the United States by type at the national, state, county, and local levels. Of the estimated 110 million tons of paper and cardboard waste managed domestically in 2019, approximately 56% was landfilled, 6% was combusted, and 38% was recycled. The estimated market value of paper and cardboard lost to landfilling in 2019 was $4 billion, and the estimated losses of embodied energy and combustion energy were equivalent to 9% and 4% of U.S. primary industrial energy consumption, respectively. Associated landfilling fees amounted to almost $4 billion. This study aims to inform efforts to implement beneficial waste-management strategies by policy makers, researchers, businesses, and communities across the United States and to provide a model for similar studies in other parts of the world.

Introduction: Monitoring the atypical antipsychotic drug clozapine is crucial to ensure patient safety. This article showcases a high-throughput analytical method for measuring clozapine and its primary metabolite norclozapine (N-desmethylclozapine) in serum using paper spray mass spectrometry (PS-MS). Objectives: This study aimed to assess the viability of a PS-MS method for the rapid measurement of clozapine and norclozapine in human serum samples as an alternative to liquid chromatography mass spectrometry (LC-MS). Methods: Serum samples were processed by protein precipitation followed by deposition of the supernatant containing labelled internal standards onto paper spray substrates mounted in cartridges. Analytes were then analyzed using a triple quadrupole mass spectrometer equipped with a commercial paper spray ionization source. The results obtained from the patient samples were compared to those from a validated LC-MS assay. Results: PS-MS calibrations for clozapine and norclozapine were linear (R2 > 0.99) over five days. Between-run precision was below 8 %, and within-run precision did not exceed 10 %. When compared to a validated LC-MS method, the mean bias for 39 patient samples was −9% for clozapine and −1% for norclozapine, with no outliers. Mass spectrometry ion ratio comparisons indicated no interference for patient samples above the lower limit of quantification. There was less than 7 % change in the measured concentrations of both analytes over five days for samples dried on paper substrates. Notably, virtually no maintenance of the MS source was required during this study. Conclusion: This study illustrates the potential of PS-MS for serum drug monitoring in the clinical laboratory.

A pre-treatment process was evaluated in this work for wastewater from paper recycling using microwave technology followed by rapid precipitation of contaminants through centrifugation. Artificial neural networks (ANNs) were used to analyze and optimize the turbidity values. Thirty experimental runs were utilized including microwave (MW) power, duration, centrifuge time, and centrifuge speed as input variables, generated by the Central Composite Full Design (CCFD) approach. The experimental turbidity ranged from 8.1 to 19.7 NTU, while predicted values ranged from 8.4 to 19.7 NTU by ANN. The ANN model showed a robust prediction performance with low mean squared error values during training and testing. Moreover, high R2 values showed a remarkable agreement between the experimental observations and ANN predictions. The results obtained from the input values (A:150.00, B:60.00, C:15.00, D:30.00) of sample 2, which gave the lowest turbidity value, showed the most removal of pollution. The results obtained from the input values (A:250.00, B:60.00, C:7.00, D:20.00) of sample 30, which gave the highest turbidity value, showed the least removal of pollution. The results showed that increasing RPM and time of the centrifugation process significantly affected the removal of pollution in wastewater.

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage.

Alternanthera philoxeroides and Hypophthalmichthys molitrix offer significant nutritional benefits. This study evaluates the proximate composition, amino acid profile, GC-MS analysis, FT-IR spectroscopy, SEM and EDX, and color values of edible paper sheets (EPSs) derived from Alternanthera philoxeroides incorporating different levels of Hypophthalmichthys molitrix flesh. The protein content in the EPSs varied based on fish flesh incorporation, peaking at 52.66% in Ap100/Hm300 (Non-boil). Protein and carbohydrate contents showed an inverse correlation across EPSs, with the highest carbohydrate content of 60.89% in sample Ap400/Hm0 (Boil). Lipid content was also found to correlate with H. molitrix flesh content in EPSs, ranging from 1.59% to 18.41%. Amino acid analysis identified 11 types, with methionine as the most prevalent, followed by leucine, phenylalanine, and lysine. GC-MS analysis revealed 51 bioactive compounds, including carbonic acid, hentriacontane, and various fatty acids. FT-IR analysis showed characteristic bonds, while color analysis displayed L* values ranging from 24.37 to 30.97. SEM analyses depicted the microstructure, surface view, and elemental composition of the EPSs, and EDX showed an abundance of Ca, N, K, O, C, Mg, Na, P, Cl, Mn, and Fe. Therefore, EPSs prepared from A. philoxeroides and H. molitrix could offer a promising approach for effectively utilizing aquatic biomass and providing both plant and animal nutrients to consumers.

Nanofibrillated cellulose (NFC) and its combined usage with cationic starch and a cationic copolymer of acrylamide were studied in relation to the properties of paper. Independent pulp treatments using additives separately included 0%, 5%, 10%, and 15% refined long fiber pulp, 3 and 6% NFC, 0.75 and 1.5% cationic starch and 0.07% and 0.15% cationic polyacrylamide and combined treatments. Handsheets were made of the above treatments, and finally their optical and microscopic properties were evaluated. Increasing the NFC content to 6% increased the brightness and yellowness of the white liner by 13% and 21%, respectively. The liner opacity was also reduced by 1%. Additionally, increasing NFC by 6% compared to imported long fibers, the brightness and yellowness of the white liner increased 5.44% and 6.3%, respectively. The liner opacity was also reduced by 1%. A 1.5% cationic starch addition to NFC increased the brightness of the white liner by 4.4%, its whiteness increased 1.5%, and its yellowness increased 2.1%. The opacity of the liner was also reduced by 7.1%. The use of NFC and cationic starch can improve the optical properties of the white liner, while imported long fibers may be problematic.

It is more important to improve and complete the wastewater process in order to reuse and return it to the production line. In this study, the hydrogen peroxide/ozone process (Peroxone) was investigated as a supplementary step in paper mill wastewater treatment to reduce the amount of chemical oxygen demand and remove E. coli. In this regard, using the Box-Behnken Design method based on the response surface method to optimize and investigate the effect of three variables governing the ozonation process, including the amount of hydrogen peroxide consumed (ml), the amount of ozone input (mg/min) and ozonation time (min) were used. The results showed that the amount of ozone and hydrogen peroxide had the greatest effect for reducing COD (up to about 75%). Also, all three variables have played a significant role in increasing the efficiency of the Peroxone process and even completely eliminating E. coli. In determining the optimal conditions, the amount of ozone (146 mg/min), the amount of hydrogen peroxide (2ml) and the duration of ozonation (23 min), the lowest amount of residual COD (73 mg/L) and the highest efficiency (75% removal of E. coli) are predicted. The results showed that due to the interaction of ozone and hydrogen peroxide, the peroxone process performance was less efficient than the ozonation process alone.

Se describen a los micro-papers como formatos novedosos e incipientes para la difusión del conocimiento científico, tanto en revistas científicas como a través de otros métodos nativos del Internet (repositorios, blogs, etcétera). Planteamos la importancia de la utilización de este formato reducido de comunicación de la ciencia para transmitir ciertos tipos de hallazgos, pues presenta una condensación de la información básica en un documento breve, de fácil lectura y con amplia audiencia, sin perder la calidad propia de los trabajos científicos revisados. Para ello, se realiza un estudio descriptivo de carácter exploratorio por medio de una revisión bibliográfica que ahonda en su uso actual y experiencias previas. Concluimos que su viabilidad para la difusión de contenidos científicos concretos busca la agilidad, sin que ello implique la pérdida de la calidad en la difusión científica.