Search

It has been clearly demonstrated that it would be feasible to consider recycling paper in an academic institution. This can be achieved through combining specific waste paper baskets, a pulping machine and power supplied by a renewable energy source, with an already established local paper making company. The paper making company would be able to gain a subsidy from the government which pays them to actually recycle paper, to counteract the cost of the pulped paper which is 30% more expensive than raw wood pulp. The academic institution would save money on waste disposal and decrease its carbon footprint by 600% with savings of up to around 5e6 tons of CO2 per year, instead of the 1e2 tones carbon offset for just recycling the paper normally. This entire process could be adapted for recycling the vast quantities of waste paper produced by students, an initiative which often fails due to the high cost of disposal. This could be achieved through urged use of the same paper disposal methods already in use, with the paper being collected and pulped once a week directly from the student paper waste bins. This research aims to study and limit the quantities of paper consumed in academic institutions in Iraq, by identifying the steps of recycling, and the extent of its environmental and economic impact, on the one hand, and on the other hand, the extent to which the Iraqi university community accepts this idea, and then study these quantities and evaluate them economically and find out the possibility of establishing a paper recycling plant based on these quantities. As well as the current research deals with the accumulation of paper waste caused by the performance of exams. In the third semester of the research, the amount of paper waste at Thi Qar University was calculated as a model for conducting a detailed research study of all departments and colleges of the University. the amount of paper waste was (11,055 tons/year), as well as calculating the cost of paper processing for the University amounted to (126252271 Iraqi dinars) and at the end of the third semester, the amount of paper waste in Iraqi academic institutions for the academic year 2022e2023, approximately (367,60976 tons/year). The cost of preparing exam books in Iraqi academic institutions for the academic year 2022e2023 amounted to approximately (4202150971 Iraqi dinars). The devices used in the practical aspect and each device and its purpose in the paper waste recycling process were explained. In addition, in the fourth chapter of the research, waste recycling was carried out in a practical way, and the results were satisfactory. We proposed a project to establish a paper and cardboard waste recycling plant in Nasiriyah, detailing its technical processes and stages in a mature way, the costs of establishing such projects in detail, as well as the annual profit of the project. At the conclusion of the research, some important recommendations were attached that help the paper waste recycling process and its success. [ABSTRACT FROM AUTHOR]

Excessive copper (Cu2+) causes adverse effects on human health and the ecological environment. Traditional methods for detecting Cu2+ have drawbacks such as high detection costs, complex operating conditions, and being time consuming. Therefore, there is an urgent need to develop simple detection methods to better meet specific health and environment quality needs. In this work, a paper-based fluorescence sensor was prepared (herein referred to as the as-prepared method) by immersing filter paper in aqueous polyethyleneimine (PEI) solution, and its potential use in Cu2+ detection was investigated. The results showed that the as-prepared paper samples, with fluorescence properties obtained by aggregation-induced luminescence of PEI, have selective recognition of Cu2+ based on the internal filtration effect, and the lowest detection limit is 0.03 μM. In addition, the relative error of this method is in the range of 1.80~2.23%, which is relatively comparable to the national standard method (0.63~630 μM), demonstrating high accuracy. Therefore, paper-based sensors with a simple preparation method have potential applications in the detection of Cu2+ in water. [ABSTRACT FROM AUTHOR]

Polyethylene-, polyvinylidene chloride-, and per- and polyfluoroalkyl substance-coated paper generate microplastics or fluorochemicals in the environment. Here, we report an approach for the development of oil-resistant papers using an environmentally friendly, fluorine-free, water-dispersible poly(dimethylsiloxane) (PDMS) coating on kraft paper. Carboxylic-functionalized PDMS (PDMS-COOH) was synthesized and subsequently neutralized with ammonium bicarbonate to obtain a waterborne emulsion, which was then coated onto kraft paper. The water resistance of the coated paper was determined via Cobb60 measurements. The Cobb60 value was reduced to 2.70 ± 0.14 g/m2 as compared to 87.6 ± 5.1 g/m2 for uncoated paper, suggesting a remarkable improvement in water resistance. Similarly, oil resistance was found to be 12/12 on the kit test scale versus 0/12 for uncoated paper. In addition, the coated paper retained 70–90% of its inherent mechanical properties, and more importantly, the coated paper was recycled via pulp recovery using a standard protocol with a 91.1% yield. [ABSTRACT FROM AUTHOR]

The manufacturing process for corrugated paper products is usually mass production and batch-by-batch production. Therefore, a high-speed mass production is required. Because the conveyer speed of the production line in a corrugated paper plant is very fast, unwanted material loss or even process interruption may occur during the cutting or clipping process if the corrugated paper on the conveyer is slanted. Hence, the paper alignment on a conveyer is important and necessary. In this study, we install photo-couples at both edges directly over the conveyer path to detect whether or not the corrugated paper is slanted from the number difference between non-activated photo-couples of the two edges. The deviated angle is calculated through a computer program using the detected information, and a servomotor-driven wheel aligns the paper in accordance with the calculated angle. This work reduces the material waste and promotes the production reliability and utility rate of the material for a corrugated paper plant. [ABSTRACT FROM AUTHOR]