Search

Forecasting has extreme importance in industry due to the numerous competitive advantages that it provides, allowing to foresee what might happen and adjust management decisions accordingly. Industries increasingly use sensors, which allow for large-scale data collection. Big datasets enable training, testing and application of complex predictive algorithms based on machine learning models. The present paper focuses on predicting values from sensors installed on a pulp paper press, using data collected over three years. The variables analyzed are electric current, pressure, temperature, torque, oil level and velocity. The results of XGBoost and artificial neural networks, with different feature vectors, are compared. They show that it is possible to predict sensor data in the long term and thus predict the asset's behaviour several days in advance. [ABSTRACT FROM AUTHOR]

Multiphase fluids are common in many industries, such as oil and petrochemical, and volume fraction measurement of their phases is a vital subject. Hence, there are lots of scientists and researchers who have introduced many methods and equipment in this regard, for example, photon attenuation sensors, capacitance-based sensors, and so on. These approaches are non-invasive and for this reason, are very popular and widely used. In addition, nowadays, artificial neural networks (ANN) are very attractive in a lot of fields and this is because of their accuracy. Therefore, in this paper, to estimate volume proportion of a three-phase homogeneous fluid, a new system is proposed that contains an MLP ANN, standing for multilayer perceptron artificial neural network, a capacitance-based sensor, and a photon attenuation sensor. Through computational methods, capacities and mass attenuation coefficients are obtained, which act as inputs for the proposed network. All of these inputs were divided randomly in two main groups to train and test the presented model. To opt for a suitable network with the lowest rate of mean absolute error (MAE), a number of architectures with different factors were tested in MATLAB software R2023b. After receiving MAEs equal to 0.29, 1.60, and 1.67 for the water, gas, and oil phases, respectively, the network was chosen to be presented in the paper. Hence, based on outcomes, the proposed approach's novelty is being able to predict all phases of a homogeneous flow with very low error. [ABSTRACT FROM AUTHOR]

Reservoir productivity prediction is a key component of oil and gas field development, and the rapid and accurate evaluation of reservoir productivity plays an important role in evaluating oil field development potential and improving oil field development efficiency. Fracture-vuggy reservoirs are characterized by strong heterogeneity, complex distribution, and irregular development, causing great difficulties in the efficient prediction of fracture-vuggy reservoirs' productivity. Therefore, a PSO-BP fracture-vuggy reservoir productivity prediction model optimized by feature optimization was proposed in this paper. The Chatterjee correlation coefficient was used to select the appropriate combination of seismic attributes as the input of the prediction model, and we applied the PSO-BP model to predict oil wells' production in a typical fracture-vuggy reservoir area of Tahe Oilfield, China, with the selected seismic attributes and compared the accuracy with that provided by the BP neural network, linear support vector machine, and multiple linear regression. The prediction results using the four models based on the test set showed that compared with the other three models, the MSE of the PSO-BP model increased by 23% to 62%, the RMSE increased by 12 to 38 percent, the MAE increased by 18 to 44 percent, the SSE increased by 23 to 62 percent, and the R-square value increased by 2 to 13 percent. This comparison proves that the PSO-BP neural network model proposed in this paper is suitable for the productivity prediction of fracture-vuggy reservoirs and has better performance, which is of guiding significance for the development and production of fracture-vuggy reservoirs. [ABSTRACT FROM AUTHOR]

In this paper, the effect evaluation and production prediction of staged fracturing for horizontal wells in tight reservoirs are studied. Firstly, the basic characteristics and value of horizontal wells in tight reservoirs are introduced, their geological characteristics, flow mechanism and permeability model are analyzed and the application of grey theory in effect analysis is discussed. Considering the problems of staged fracturing effect evaluation and the production prediction of horizontal wells in tight reservoirs, a BP neural network model based on deep learning is proposed. Due to the interference of multiple physical parameters and the complex functional relationship in the development of tight reservoir fracturing, the traditional prediction method has low accuracy and it is difficult to establish an accurate mapping relationship. In this paper, a BP neural network is used to simulate multivariable nonlinear mapping by modifying the model, and its advantages in solving the coupling relationship of complex functions are brought into play. A neural network model with fracturing parameters as input and oil and gas production as output is designed. Through the training and testing of data sets, the accuracy and applicability of the proposed model for effect evaluation and yield prediction are verified. The research results show that the model can fit the complex mapping relationship between fracturing information and production and provide an effective evaluation and prediction tool for the development of the staged fracturing of horizontal wells in tight reservoirs. [ABSTRACT FROM AUTHOR]

This document discusses the degradation and failure mechanisms of dielectric insulation in medium- and high-voltage power equipment. It highlights the importance of controlling insulation material degradation to prevent equipment failures and reduce the risk of environmental pollution. The document includes several research papers that address various topics related to the measurement, monitoring, and improvement of power equipment components. These papers cover issues such as winding breakdown faults in transformers, overvoltages caused by vacuum circuit breaker interruptions, insulation resistance degradation in cables, temperature rise in composite insulators, partial discharges and their effects on insulation, and acoustic inspection for detecting partial discharges. The document also presents studies on the technical condition of on-load tap changers, the behavior of silicone elastomers under electrical and mechanical stress, and the percolation phenomenon in square matrices. [Extracted from the article]

With the development of smart grids and new power systems, the combination of non-intrusive load identification technology and smart home technology can provide users with the operating conditions of home appliances and equipment, thus reducing home energy loss and improving users' ability to demand a response. This paper proposes a non-intrusive load decomposition model with a parallel multiscale attention mechanism (PMAM). The model can extract both local and global feature information and fuse it through a parallel multiscale network. This improves the attention mechanism's ability to capture feature information over long time periods. To validate the model's decomposition ability, we combined the PMAM model with four benchmark models: the Long Short-Term Memory (LSTM) recurrent neural network model, the Time Pooling-based Load Disaggregation Model (TPNILM), the Extreme Learning Machine (ELM), and the Load Disaggregation Model without Parallel Multi-scalar Attention Mechanisms (UNPMAM). The model was trained on the publicly available UK-DALE dataset and tested. The models' test results were quantitatively evaluated using a confusion matrix. This involved calculating the F1 score of the load decomposition. A higher F1 score indicates better model decomposition performance. The results indicate that the PMAM model proposed in this paper maintains an F1 score above 0.9 for the decomposition of three types of electrical equipment under the same household user, which is 3% higher than that of the other benchmark models on average. In the cross-household test, the PMAM also demonstrated a better decomposition ability, with the F1 score maintained above 0.85, and the mean absolute error (MAE) decreased by 5.3% on average compared with that of the UNPMAM. [ABSTRACT FROM AUTHOR]

Electricity consumption in buildings is one of the major causes of energy usage and knowledge of this can help building owners and users increase energy efficiency and conservation efforts. For Pacific Island countries, building electricity demand data is not readily accessible or available for constructing models to predict electricity demand. This paper starts to fill this gap by studying the case of schools in Fiji. The aim of the paper is to assess the factors affecting electricity demand for grid-connected Fijian schools and use this assessment to build mathematical models (multiple linear regression (MLR) and artificial neural network (ANN)) to predict electricity consumption. The average grid-connected electricity demand in kWh/year was 1411 for early childhood education schools, 5403 for primary schools, and 23,895 for secondary schools. For predicting electricity demand (ED) for all grid-connected schools, the stepwise MLR model shows that taking logarithm transformations on both the dependent variable and independent variables (number of students, lights, and air conditioning systems) yields statistically significant independent variables with an R2 value of 73.3% and RMSE of 0.2248. To improve the predicting performance, ANN models were constructed on both the natural form of variables and transformed variables. The optimum ANN model had an R2 value of 95.3% and an RMSE of 59.4 kWh/year. The findings of this study can assist schools in putting measures in place to reduce their electricity demand, associated costs, and carbon footprint, as well as help government ministries make better-informed policies. [ABSTRACT FROM AUTHOR]

The digitization of distribution power systems has revolutionized the way data are collected and analyzed. In this paper, the critical task of harnessing this information to identify irregularities and anomalies in electricity consumption is tackled. The focus is on detecting non-technical losses (NTLs) and energy theft within distribution networks. A comprehensive overview of the methodologies employed to uncover NTLs and energy theft is presented, leveraging measurements of electricity consumption. The most common scenarios and prevalent cases of anomalies and theft among consumers are identified. Additionally, statistical indicators tailored to specific anomalies are proposed. In this research paper, the practical implementation of numerous artificial intelligence (AI) algorithms, including the artificial neural network (ANN), ANFIS, autoencoder neural network, and K-mean clustering, is highlighted. These algorithms play a central role in our research, and our primary objective is to showcase their effectiveness in identifying NTLs. Real-world data sourced directly from distribution networks are utilized. Additionally, we carefully assess how well statistical methods work and compare them to AI techniques by testing them with real data. The artificial neural network (ANN) accurately identifies various consumer types, exhibiting a frequency error of 7.62%. In contrast, the K-means algorithm shows a slightly higher frequency error of 9.26%, while the adaptive neuro-fuzzy inference system (ANFIS) fails to detect the initial anomaly type, resulting in a frequency error of 11.11%. Our research suggests that AI can make finding irregularities in electricity consumption even more effective. This approach, especially when using data from smart meters, can help us discover problems and safeguard distribution networks. [ABSTRACT FROM AUTHOR]

The life expectancy of power transformers is primarily determined by the integrity of the insulating oil and cellulose paper between the conductor turns, phases and phase to earth. During the course of their in-service lifetime, the solid insulating system of windings is contingent on long-standing ageing and decomposition. The decomposition of the cellulose paper insulation is strikingly grievous, as it reduces the tensile strength of the cellulose paper and can trigger premature failure. The latter can trigger premature failure, and to realize at which point during the operational life this may occur is a daunting task. Various methods of estimating the DP have been proposed in the literature; however, these methods yield different results, making it difficult to accurately estimate a reliable DP. In this work, a novel approach based on the Feedforward Backpropagation Artificial Neural Network has been proposed to predict the amount of DP in transformer cellulose insulation. Presently, no ANN model has been proposed to predict the remaining DP using 2FAL concentration. A databank comprising 100 data sets—70 for training and 30 for testing—is used to develop the proposed ANN using 2-furaldehyde (2FAL) as an input and DP as an output. The proposed model yields a correlation coefficient of 0.958 for training, 0.915 for validation, 0.996 for testing and an overall correlation of 0.958 for the model. [ABSTRACT FROM AUTHOR]

Short-term load forecasting is a challenging research problem and has a tremendous impact on electricity generation, transmission, and distribution. A robust forecasting algorithm can help power system operators to better tackle the ever-changing electric power demand. This paper presents a novel deep neural network for short-term electric load forecasting for the St. John's campus of Memorial University of Newfoundland (MUN). The electric load data are obtained from the Memorial University of Newfoundland and combined with metrological data from St. John's. This dataset is used to formulate a multivariate time-series forecasting problem. A novel deep learning algorithm is presented, consisting of a 1D Convolutional Neural Network, which is followed by an encoder–decoder-based network with attention. The input used for this model is the electric load consumption and metrological data, while the output is the hourly prediction of the next day. The model is compared with Gated Recurrent Unit (GRU) and Long Short Term Memory (LSTM)-based Recurrent Neural Network. A CNN-based encoder–decoder model without attention is also tested. The proposed model shows a lower mean absolute error (MAE), mean squared error (MSE), mean absolute percentage error (MAPE), and higher R2 score. These evaluation metrics show an improved performance compared to GRU and LSTM-based RNNs as well as the CNN encoder–decoder model without attention. [ABSTRACT FROM AUTHOR]

Artificial neural networks (ANNs) can be used for accurate heat load forecasting in district heating systems (DHSs). This paper presents an application of a shallow ANN with two hidden layers in the case of a local DHS. The developed model was used to write a simple application in Python 3.10 that can be used in the operation of a district heating plant to carry out a preliminary analysis of heat demand, taking into account the ambient temperature on a given day. The model was trained using the real data from the period 2019–2022. The training was sufficient for the number of 150 epochs. The prediction effectiveness indicator was proposed. In the considered case, the effectiveness of the trained network was 85% and was better in comparison to five different regression models. The developed tool was based on an open-source programming environment and proved its ability to predict heating load. [ABSTRACT FROM AUTHOR]

A photovoltaic (PV) power forecasting prediction is a crucial stage to utilize the stability, quality, and management of a hybrid power grid due to its dependency on weather conditions. In this paper, a short-term PV forecasting prediction model based on actual operational data collected from the PV experimental prototype installed at the engineering college of Misan University in Iraq is designed using various machine learning techniques. The collected data are initially classified into three diverse groups of atmosphere conditions—sunny, cloudy, and rainy meteorological cases—for various seasons. The data are taken for 3 min intervals to monitor the swift variations in PV power generation caused by atmospheric changes such as cloud movement or sudden changes in sunlight intensity. Then, an artificial neural network (ANN) technique is used based on the gray wolf optimization (GWO) and genetic algorithm (GA) as learning methods to enhance the prediction of PV energy by optimizing the number of hidden layers and neurons of the ANN model. The Python approach is used to design the forecasting prediction models based on four fitness functions: R2, MAE, RMSE, and MSE. The results suggest that the ANN model based on the GA algorithm accommodates the most accurate PV generation pattern in three different climatic condition tests, outperforming the conventional ANN and GWO-ANN forecasting models, as evidenced by the highest Pearson correlation coefficient values of 0.9574, 0.9347, and 0.8965 under sunny, cloudy, and rainy conditions, respectively. [ABSTRACT FROM AUTHOR]

With the continuous development of computer technology, artificial intelligence has been widely applied across various industries. To address the issues of high computational cost and inefficiency in traditional numerical methods, this paper proposes a data-driven artificial intelligence approach for solving high-dimensional neutron transport equations. Based on the AFA-3G assembly model, a neutron transport equation solving model is established using deep neural networks, considering factors that influence the neutron transport process in real engineering scenarios, such as varying temperature, power, and boron concentration. Comparing the model's predicted values with reference values, the average error in the infinite multiplication factor kinf of the assembly is found to be 145.71 pcm (10−5), with a maximum error of 267.10 pcm. The maximum relative error is less than 3.5%, all within the engineering error standards of 500 pcm and 5%. This preliminary validation demonstrates the feasibility of using data-driven artificial intelligence methods to solve high-dimensional neutron transport equations, offering a new option for engineering design and practical engineering computations. [ABSTRACT FROM AUTHOR]

Digital substations have adopted a high amount of information and communication technology (ICT) and cyber–physical systems (CPSs) for monitoring and control. As a result, cyber attacks on substations have been increasing and have become a major concern. An intrusion-detection system (IDS) could be a solution to detect and identify the abnormal behaviors of hackers. In this paper, a Deep Neural Network (DNN)-based IDS is proposed to detect malicious generic object-oriented substation event (GOOSE) communication over the process and station bus network, followed by the multiclassification of the cyber attacks. For training, both the abnormal and the normal substation networks are monitored, captured, and logged, and then the proposed algorithm is applied for distinguishing normal events from abnormal ones within the network communication packets. The designed system is implemented and tested with a real-time IEC 61850 GOOSE message dataset using two different approaches. The experimental results show that the proposed system can successfully detect intrusions with an accuracy of 98%. In addition, a comparison is performed in which the proposed IDS outperforms the support vector machine (SVM)-based IDS. [ABSTRACT FROM AUTHOR]

As a public service, municipal waste management at the local and regional levels should be carried out in an environmentally friendly and economically justified manner. Information on the quantity and composition of generated municipal waste is essential for planning activities related to the implementation and optimization of the process. There is a need for reliable forecasts regarding the amount of waste generated in each area. Due to the variability in the waste accumulation rate, this task is difficult to accomplish, especially at the local level. The literature contains many reports on this issue, but there is a lack of studies indicating the preferred method depending on the independent variables, the complexity of the algorithm, the time of implementation, and the quality of the forecast. The results concerning the quality of forecasting methods are difficult to compare due to the use of different sets of independent variables, forecast horizons, and quality assessment indicators. This paper compares the effectiveness of selected forecasting models in predicting the amount of municipal waste collection generated in Polish municipalities. The authors compared nine methods, including artificial neural networks (ANNs), support regression trees (SRTs), rough set theory (RST), multivariate adaptive regression splines (MARS), and random regression forests (RRFs). The analysis was based on 31 socioeconomic indicators for 2451 municipalities in Poland. The Boruta algorithm was used to select significant variables and eliminate those with little impact on forecasting. The quality of the forecasts was evaluated using eight indicators, such as the absolute percentage error (MAPE), mean absolute error (MAE), and coefficient of determination (R2). A comprehensive evaluation of the forecasting models was carried out using the APEKS method. An analysis of the results showed that the best forecasting methods depended on the set of independent variables and the evaluation criteria adopted. Waste management expenditures, the levels of sanitation and housing infrastructure, and the cost-effectiveness of waste management services were key factors influencing the amount of municipal waste. Additionally, this research indicated that adding more variables does not always improve the quality of forecasts, highlighting the importance of proper selection. The use of a variable selection algorithm, combined with the consideration of the impact of various socioeconomic factors on municipal waste generation, can significantly improve the quality of forecasts. The SRT, CHAID, and MARS methods can become valuable tools for predicting municipal waste volumes, which, in turn, will help to improve waste management system. [ABSTRACT FROM AUTHOR]

The energy transition towards a low-emission matrix has motivated efforts to reduce the use of fossil fuels in the transportation sector. The growth of the electric mobility market has been consistent in recent years. In Brazil, there has been an accelerated growth in the sales rate of new electric (and hybrid) vehicles (EVs). Fiscal incentives provided by governments, along with the reduction in vehicle costs, are factors contributing to the exponential growth of the EV fleet—creating a favorable environment for the dissemination of new technologies and enabling the participation of players from sectors such as battery manufacturing and charging stations. Considering the international context, the E-Lounge R&D joint initiative aims to evaluate different strategies to economically enable the electric mobility market, exploring EV charging service sales by energy distribution utility companies in Brazil. This work describes the step-by-step development of an ideal model of a charging hub and discusses its operation based on a real deployment, as well as its associated technical and economic feasibility. Using EV charging data based on the E-Lounge's operational behavior, an artificial neural network (ANN) is applied to forecast future energy consumption to each EV charging station. This paper also presents an economic analysis of the E-Lounge case study, which can contribute to proposals for electric vehicle charging ecosystems in the context of smart energy systems. Based on the operational results collected, as well as considering equipment usage projections, it is possible to make EV charging enterprises feasible, even when high investments in infrastructure and equipment (charging stations and battery storage systems) are necessary, since the net present value is positive and the payback period is 4 years. This work contributes by presenting real operational data from a charging hub, a projection model aimed at evaluating future operations, and a realistic economic evaluation model based on a case study implemented in São Paulo, Brazil. [ABSTRACT FROM AUTHOR]

The management of large enterprises influences their efficiency and profitability. One of the important aspects is the appropriate management of electricity consumption used for production and daily operation. The problem becomes more complicated when you need to manage not one but a large complex of buildings with heterogeneous purposes. In the paper, we examine real-time series data of electrical energy consumption in a complex of heterogeneous buildings, including offices and warehouses, using time series analysis methods such as the Holt–Winters model and ARIMA/SARIMA model, and neural networks (Deep Neural Network, Recurrent Neural Network, and Long Short-Term Memory). Experimental research was performed on a dataset obtained from an energy consumption meter placed in the building complex, built in different periods, and equipped with a variety of automation devices. The data were collected over a period of four years 2018–2021 in the form of time series. Results show that classic models are good at predicting energy consumption in the mentioned type of buildings. The ARIMA model gave the best results—for buildings characterized by seasonality and trends the forecasts were almost perfect with actual values. [ABSTRACT FROM AUTHOR]

The potential of unconventional hydrocarbon resources has been unlocked since the hydraulic fracturing technique in combination with long horizontal wells was applied to develop this type of reservoir economically. The design and optimization of the fracturing treatment and the stimulated reservoir volume and the forecasting of production performance are crucial for the development and management of such resources. However, the production performance of tight gas reservoirs is a complicated nonlinear problem, described by many parameters loaded with uncertainty. The complexity of the problem influences and inspires the sophistication of the solution to be used. This paper proposed an artificial network model that allows for fast, extended, and accurate analyses of the production performance of multiple fractured unconventional tight gas wells. In the comprehensive approach developed, the reservoir rock parameters, the drainage area, and the hydraulic fracture parameters are treated as a variable input to the model. The analysis is no longer constrained by fixed "shoes box" geometry, and the values of the parameters defining the reservoir and stimulated volume are not limited to a few discrete values. The numerical experiment used to construct a database for model development was designed using a genetically optimized Latin hypercube sampling technique. A special approach was used in the preparation of "blind data", which are crucial for truly reliable model verification. In the result, a developed tool offers an extended rock-fluid description, flexible model, and stimulated reservoir volume dimensioning and parameterization, as well as a high degree of applicability in sensitivity analysis and/or optimization. [ABSTRACT FROM AUTHOR]

To enhance the operational efficiency and fault detection accuracy of hydroelectric units, this paper proposes a parallel convolutional neural network model that integrates the Gramian angular summation field (GASF) with an Improved coati optimization algorithm–parallel convolutional neural network (ICOA-PCNN). Additionally, to further improve the model's accuracy in fault identification, a multi-head self-attention mechanism (MSA) and support vector machine (SVM) are introduced for a secondary optimization of the model. Initially, the GASF technique converts one-dimensional time series signals into two-dimensional images, and a COA-CNN dual-branch model is established for feature extraction. To address the issues of uneven population distribution and susceptibility to local optima in the COA algorithm, various optimization strategies are implemented to improve its global search capability. Experimental results indicate that the accuracy of this model reaches 100%, significantly surpassing other nonoptimized models. This research provides a valuable addition to fault diagnosis technology for modern hydroelectric units. [ABSTRACT FROM AUTHOR]

This paper presents a model for determining the availability of continuous systems at open pits using the neuro-fuzzy system. The concept of availability is divided into partial indicators (synthetic indicators and sub-indicators). The presented model in relation to already existing models for determining availability uses a combination of the advantages of artificial neural networks and fuzzy logic. The case study addressed the I ECC (bucket wheel excavator–conveyors–crushing plant) system of the open pit Drmno, Kostolac. In this paper, in addition to the ANFIS model for determining the availability of continuous systems, a simulation model was developed. The obtained results of the ANFIS model were verified with the help of a simulation model that uses certain assumptions about the distribution of failures. This paper was created as a result of several years of field and theoretical research into the availability of continuous systems in open pits, and completes a cycle that consists of several published articles on the subject of modeling the behavior of these systems in real time using a time picture of the state, expert assessment, simulation and AI models, while respecting the multidisciplinarity of the problem (mining technological, mechanical, and information technological aspects). The developed ANFIS model is a key instrument for improving operational efficiency and resource management in the mining sector. Its ability to accurately predict the availability of the ECC system brings not only operational benefits through reduced downtime and optimized maintenance, but also a potential reduction in overall costs at coal open pits. Such an innovative model marks a significant step forward in the mining industry, especially when it comes to continuous systems in coal open pits. [ABSTRACT FROM AUTHOR]

ANNs have become a cornerstone in efficiently managing building energy management systems (BEMSs) as they offer advanced capabilities for prediction, control, and optimization. This paper offers a detailed review of recent, significant research in this domain, highlighting the use of ANNs in optimizing key energy systems, such as HVAC systems, domestic water heating (DHW) systems, lighting systems (LSs), and renewable energy sources (RESs), which have been integrated into the building environment. After illustrating the conceptual background of the most common ANN architectures for controlling BEMSs, the current work dives deep into relative research applications, thereby exhibiting their methodology and outcomes. By summarizing the numerous impactful applications during 2015–2023, this paper categorizes the predominant ANN-based techniques according to their methodological approach, specific energy equipment, and experimental setups. Grounded in the different perspectives that the integrated studies illustrate, the primary focus of this paper is to evaluate the overall status of ANN-driven control in building energy management, as well as to offer a deep understanding of the prevailing trends at the building level. Leveraging detailed graphical depictions and comparisons between different concepts, future directions, and fruitful conclusions are drawn, and the upcoming innovations of ANN-based control frameworks in BEMSs are highlighted. [ABSTRACT FROM AUTHOR]

Drying processes are among the most energy-intensive industrial processes. There is a need for development of the efficient methods needed for estimating, measuring, and reducing energy use. Different machine learning algorithms might provide some of the answers to these issues in a faster and less costly way, without the need for time-consuming and expensive experiments done at different scales of the dryers. The aim of this paper was to provide a comprehensive overview of machine learning applications for addressing energy-related challenges by exploration of different energy types and energy reduction opportunities. Also, the analysis of the applied algorithms, their specific applications and a critical evaluation of the obtained results are provided. The paper is based on the necessity of the improvements in energy use needed for drying related on the existing data. The overview of the ways for such achievements, and a general classification of machine learning algorithm are the background of the paper. The methods used are the machine learning techniques employed in different energy-related issues for drying processes. The paper focuses on the applications of artificial neural networks and other machine learning algorithms and models for different energy-related issues, including different energy types applications, challenges associated with energy consumption, and opportunities for energy reduction. Not only the applied algorithms, but also their specific applications, and the statistical analysis of the obtained results are also overviewed. Finally, a critical evaluation of the findings highlighting the potentials of machine learning algorithms in addressing energy-related challenges (such as estimation of energy consumption, opportunities for energy reduction, and use of different energy sources) is provided. The presented analysis underscored the effectiveness of machine learning applications for these purposes. [ABSTRACT FROM AUTHOR]

Electrical drive systems are commonly applied for the mechanisms of precise movement, where having a high-quality position and high-quality speed control is especially valuable. Very often, the mechanical part of these systems reveals resonant properties that are related to the limited stiffness of the interconnection between subsequent parts of the mechanism. In most cases, this sort of system may be described as a model of several linked masses. If only the structure of the mechanical part is known and the corresponding parameters are constant and identified, the demanded control quality may be obtained using a properly tuned ADRC or PID controller equipped with appropriate anti-resonance filtration. However, if the parameters of the mechanical part are variant, adaptive control may be considered as a solution. In this paper, artificial neural network (ANN) is considered to be a speed controller and its training method assures adaptation to the unknown mechanical parameters. The paper is particularly focused on a three-mass system, which possesses, due to its structure, two resonant frequencies. The unique property of the analyzed system is the application of drive units at both ends of the system, so that the controller has the ability to influence the resonant system from both sides. The coordination of the drive unit is performed by the aforementioned ANN, from which two outputs affect the drive units independently. The derivation of the mathematical model is followed by its implementation in a computer simulation and finally the evaluation in a dedicated laboratory setup, the construction of which is also presented in the paper. [ABSTRACT FROM AUTHOR]

Lithium-ion batteries are widely used in electric vehicles, energy storage power stations, and many other applications. Accurate and reliable monitoring of battery health status and remaining capacity is the key to establish a lithium-ion cell management system. In this paper, based on a Bayesian optimization algorithm, a deep neural network is structured to evaluate the whole charging curve of the battery using partial charging curve data as input. A 0.74 Ah battery is used for experiments, and the effect of different input data lengths is also investigated to check the high flexibility of the approach. The consequences show that using only 20 points of partial charging data as input, the whole charging profile of a cell can be exactly predicted with a root-mean-square error (RMSE) of less than 19.16 mAh (2.59% of the nominal capacity of 0.74 Ah), and its mean absolute percentage error (MAPE) is less than 1.84%. In addition, critical information including battery state-of-charge (SOC) and state-of-health (SOH) can be extracted in this way to provide a basis for safe and long-lasting battery operation. [ABSTRACT FROM AUTHOR]

Using multiple input power sources increases the reliability of electric vehicles compared to a single source. However, the inclusion of other sources exhibits complexity in the controller system, such as computing time, program difficulty, and switching speed to connect or disconnect the input power to load. To ensure optimal performance and avoid overloading issues, the EV system needs sophisticated control. This work introduces a machine-learning-based controller using an artificial neural network to solve these problems. This paper describes the detailed power management control methodology using multiple sources like solar PV, fuel cells, and batteries. Novel control with an instantaneous reference current scheme is used to manage the input power sources to satisfy the power demand of electric vehicles. The proposed work executes the power split-up operation with standard and actual drive cycles and maximum power point tracking for PV panels using MATLAB Simulink. Finally, power management with a machine learning technique is implemented in an experimental analysis with the LabVIEW software, and an FPGA controller is used to control a 48 V, 1 kW permanent-magnet synchronous machine. [ABSTRACT FROM AUTHOR]

In order to improve the reliability and life of the wind turbine, this paper takes the rolling bearing in the experimental platform of the wind turbine as the research object. In order to obtain the intrinsic mode function (IMF) of each fault type, the original signals of different fault states of the rolling bearing on the experimental platform are decomposed by using the overall average empirical mode decomposition method (EEMD) and the wavelet packet decomposition method (WPD), respectively. Then the energy ratio of the IMF component of the different types of faults to the total energy value is calculated and the eigenvectors of different types of faults are constructed. The extreme learning machine (ELM) and probabilistic neural network (PNN) are used to learn fault types and eigenvector samples to identify the faults of the rolling bearing. It is found that the bearing fault characteristics obtained by the WPD method are more obvious, and the results obtained by the same recognition method are ideal; and the PNN method is obviously superior to the extreme learning machine method in bearing fault recognition rate. [ABSTRACT FROM AUTHOR]

Accurate quantification of uncertainty in solar photovoltaic (PV) generation forecasts is imperative for the efficient and reliable operation of the power grid. In this paper, a data-driven non-parametric probabilistic method based on the Naïve Bayes (NB) classification algorithm and Dempster–Shafer theory (DST) of evidence is proposed for day-ahead probabilistic PV power forecasting. This NB-DST method extends traditional deterministic solar PV forecasting methods by quantifying the uncertainty of their forecasts by estimating the cumulative distribution functions (CDFs) of their forecast errors and forecast variables. The statistical performance of this method is compared with the analog ensemble method and the persistence ensemble method under three different weather conditions using real-world data. The study results reveal that the proposed NB-DST method coupled with an artificial neural network model outperforms the other methods in that its estimated CDFs have lower spread, higher reliability, and sharper probabilistic forecasts with better accuracy. [ABSTRACT FROM AUTHOR]

Demand response management (DRM) plays a crucial role in the prospective development of smart grids. The precise estimation of electricity demand for individual houses is vital for optimizing the operation and planning of the power system. Accurate forecasting of the required components holds significance as it can substantially impact the final cost, mitigate risks, and support informed decision-making. In this paper, a forecasting approach employing neural networks for smart grid demand-side management is proposed. The study explores various enhanced artificial neural network (ANN) architectures for forecasting smart grid consumption. The performance of the ANN approach in predicting energy demands is evaluated through a comparison with three statistical models: a time series model, an auto-regressive model, and a hybrid model. Experimental results demonstrate the ability of the proposed neural network framework to deliver accurate and reliable energy demand forecasts. [ABSTRACT FROM AUTHOR]

Power quality improvement and Power quality disturbance (PQD) detection are two significant concerns that must be addressed to ensure an efficient power distribution within the utility grid. When the process to analyze PQD is migrated to real-time platforms, the possible occurrence of a phase mismatch can affect the algorithm's accuracy; this paper evaluates phase shifting as an additional stage in signal acquisition for detecting and classifying eight types of single power quality disturbances. According to their mathematical models, a set of disturbances was generated using an arbitrary waveform generator BK Precision 4064. The acquisition, detection, and classification stages were embedded into a BeagleBone Black. The detection stage was performed using multiresolution analysis. The feature vectors of the acquired signals were obtained from the combination of Shannon entropy and log-energy entropy. For classification purposes, four types of classifiers were trained: multilayer perceptron, K-nearest neighbors, probabilistic neural network, and decision tree. The results show that incorporating a phase-shifting stage as a preprocessing stage significantly improves the classification accuracy in all cases. [ABSTRACT FROM AUTHOR]

This paper presents a new approach for the online estimation of stator and rotor resistance of induction motors for speed sensorless vector-controlled drives, using feed-forward artificial neural networks with advanced adaptive learning rates. For the rotor resistance estimation, a neural network model based on rotor speed and stator currents is developed. The rotor flux linkages acquired from the voltage model are compared with the neural network model. The feed-forward neural network employs an adaptive learning rate as the function of the obtained error during training for quick convergence with minimal estimation error. A two-layered neural network model based on the stator voltage and current equations is developed for the stator resistance estimation. The d-q axes stator currents obtained from the developed model are compared with the acquired d-q axes stator currents. For the fast convergence with minimal estimation error, an adaptive learning rate as the function of error is adopted during training. Furthermore, the neural network estimates the induction motor's speed. The simulation and experimental results justify that the developed algorithms track variation in the resistances quickly and precisely along with the speed as compared with the conventional constant learning rate algorithm, leading to reliable operation of the drive. [ABSTRACT FROM AUTHOR]

The investigation of the ignition delay of hydrocarbon fuel is highly valuable for enhancing combustion efficiency, optimizing fuel thermal efficiency, and mitigating pollutant emissions. This paper has developed a BP-MRPSO neural network model for studying hydrocarbon fuel ignition and clarified the novelty of this model compared to the traditional BP and ANN models from the literature. The model integrates the particle swarm optimization (PSO) algorithm with MapReduce-based parallel processing technology. This integration improves the prediction accuracy and processing efficiency of the model. Compared to the traditional BP model, the BP-MRPSO model can increase the average correlation coefficient, from 0.9745 to 0.9896. The R2 value for predicting fire characteristics using this model can exceed 90%. Meanwhile, when the two hidden layers of both the BP and BP-MRPSO models consist of 9 and 8 neurons, respectively, the accuracy of the BP-MRPSO model is increased by 38.89% compared to the BP model. This proved that the new BP-MRPSO model has the capacity to handle large datasets while achieving great precision and efficiency. The findings could provide a new perspective for examining the properties of fuel ignition, which is expected to contribute to the development and assessment of aviation fuel ignition characteristics in the future. [ABSTRACT FROM AUTHOR]

This paper presents a novel approach to estimating short-term production of wind farms, which are made up of numerous turbine generators. It harnesses the power of big data through a blend of data-driven and model-based methods. Specifically, it combines an Artificial Neural Network (ANN) for immediate future predictions of wind turbine power output with a stochastic model for dependability, using Hybrid Reliability Block Diagrams. A thorough state-of-the-art review has been conducted in order to demonstrate the applicability of an ANN for non-linear stochastic problems of energy or power forecast estimation. The study leverages an innovative cluster analysis to group wind turbines and reduce the computational effort of the ANN, with a dependability model that improves the accuracy of the data-driven output estimation. Therefore, the main novelty is the employment of a hybrid model that combines an ANN with a dependability stochastic model that accounts for the realistic operational scenarios of wind turbines, including their susceptibility to random shutdowns This approach marks a significant advancement in the field, introducing a methodology which can aid the design and the power production forecast. The research has been applied to a case study of a 24 MW wind farm located in the south of Italy, characterized by 28 turbines. The findings demonstrate that the integrated model significantly enhances short-term wind-energy production estimation, achieving a 480% improvement in accuracy over the solo-clustering approach. [ABSTRACT FROM AUTHOR]

With the rapid growth in the proportion of renewable energy access and the structural complexity of distributed energy systems, traditional microgrid (MG) scheduling methods that rely on mathematical optimization models and expert experience are facing significant challenges. Therefore, it is essential to present a novel scheduling technique with high intelligence and fast decision-making capacity to realize MGs' automatic operation and regulation. This paper proposes an optimal scheduling decision-making method for MGs based on deep neural networks (DNN). Firstly, a typical mathematical scheduling model used for MG operation is introduced, and the limitations of current methods are analyzed. Then, a two-stage optimal scheduling framework comprising day-ahead and intra-day stages is presented. The day-ahead part is solved by mixed integer linear programming (MILP), and the intra-day part uses a convolutional neural network (CNN)—bidirectional long short-term memory (Bi LSTM) for high-speed rolling decision making, with the outputs adjusted by a power correction balance algorithm. Finally, the validity of the model and algorithm of this paper are verified by arithmetic case analysis. [ABSTRACT FROM AUTHOR]

Building automation systems installed in large commercial buildings record sub-hourly measurements from hundreds of sensors. The use of such large datasets are challenging because of missing and erroneous data, which can prevent the development of accurate prediction models of the performance of heating, ventilation, and air-conditioning equipment. The use of the transfer learning (TL) method for building applications attracted researchers to solve the problems created by small and incomplete datasets. This paper verifies the hypothesis that the deep neural network models that are pre-trained for one chiller (called the source chiller) with a small dataset of measurements from July 2013 could be applied successfully, by using TL strategies, for the prediction of the operation performance of another chiller (called the target chiller) with different datasets that were recorded during the cooling season of 2016. Measurements from a university campus are used as a case study. The results show that the initial hypothesis of this paper is confirmed. [ABSTRACT FROM AUTHOR]

With the rapid growth of power demand and the advancement of new power system intelligence, smart energy measurement system data quality and security are also facing the influence of diversified factors. To solve the series of problems such as low data prediction efficiency, poor security perception, and "data islands" of the new power system, this paper proposes a federated learning system based on the Improved Hunter–Prey Optimizer Optimized Wavelet Neural Network (IHPO-WNN) for the whole-domain power load prediction. An improved HPO algorithm based on Sine chaotic mapping, dynamic boundaries, and a parallel search mechanism is first proposed to improve the prediction and generalization ability of wavelet neural network models. Further considering the data privacy in each station area and the potential threat of cyber-attacks, a localized differential privacy-based federated learning architecture for load prediction is designed by using the above IHPO-WNN as a base model. In this paper, the actual dataset of a smart energy measurement master station is selected, and simulation experiments are carried out through MATLAB software to test and examine the performance of IHPO-WNN and the federal learning system, respectively, and the results show that the method proposed in this paper has high prediction accuracy and excellent practical performance. [ABSTRACT FROM AUTHOR]

Optimal power flow (OPF) is a crucial tool in the operation and planning of modern power systems. However, as power system optimization shifts towards larger-scale frameworks, and with the growing integration of distributed generations, the computational time and memory requirements of solving the alternating current (AC) OPF problems can increase exponentially with system size, posing computational challenges. In recent years, machine learning (ML) has demonstrated notable advantages in efficient computation and has been extensively applied to tackle OPF challenges. This paper presents five commonly employed OPF transformation techniques that leverage ML, offering a critical overview of the latest applications of advanced ML in solving OPF problems. The future directions in the application of machine learning to AC OPF are also discussed. [ABSTRACT FROM AUTHOR]

This present review explores the application of artificial intelligence (AI) methods in analysing the prediction of thermophysical properties of nanofluids. Nanofluids, colloidal solutions comprising nanoparticles dispersed in various base fluids, have received significant attention for their enhanced thermal properties and broad application in industries ranging from electronics cooling to renewable energy systems. In particular, nanofluids' complexity and non-linear behaviour necessitate advanced predictive models in heat transfer applications. The AI techniques, which include genetic algorithms (GAs) and machine learning (ML) methods, have emerged as powerful tools to address these challenges and offer novel alternatives to traditional mathematical and physical models. Artificial Neural Networks (ANNs) and other AI algorithms are highlighted for their capacity to process large datasets and identify intricate patterns, thereby proving effective in predicting nanofluid thermophysical properties (e.g., thermal conductivity and specific heat capacity). This review paper presents a comprehensive overview of various published studies devoted to the thermal behaviour of nanofluids, where AI methods (like ANNs, support vector regression (SVR), and genetic algorithms) are employed to enhance the accuracy of predictions of their thermophysical properties. The reviewed works conclusively demonstrate the superiority of AI models over the classical approaches, emphasizing the role of AI in advancing research for nanofluids used in heat transfer applications. [ABSTRACT FROM AUTHOR]

To reduce the energy consumption of domestic hot water (DHW) production, it is necessary to reasonably select a water supply plan through early predictions of DHW consumption to optimize energy consumption. However, the fluctuations and intermittence of DHW consumption bring great challenges to the prediction of water consumption. In this paper, an ANN-LSTM-A water quantity prediction model based on attention mechanism (AM) enhancement is improved. The model includes an input layer, an AM layer, a hidden layer, and an output layer. Based on the combination of artificial neural network (ANN) and long short-term memory (LSTM) models, an AM is incorporated to address the issue of the traditional ANN model having difficulty capturing the long-term dependencies, such as lags and trends in time series, to improve the accuracy of the DHW consumption prediction. Through comparative experiments, it was found that the root mean square error of the ANN-LSTM-A model was 15.4%, 13.2%, and 13.2% lower than those of the ANN, LSTM, and ANN-LSTM models, respectively. The corresponding mean absolute error was 17.9%, 11.5%, and 8% lower than those of the ANN, LSTM, and ANN-LSTM models, respectively. The results showed that the proposed ANN-LSTM-A model yielded better performances in predicting DHW consumption than the ANN, LSTM, and ANN-LSTM models. This work provides an effective reference for the reasonable selection of the water supply plan and optimization of energy consumption. [ABSTRACT FROM AUTHOR]

Insulation resistance (IR) is an essential metric indicating insulation conditions of extruded power cables. To deliver reliable IR simulation as a reference for practical cable inspection, in this paper, four IR degradation models for cross-linked polyethylene-insulated cables under thermal ageing are presented. In addition, the influences of methodologies and temperature profiles on IR simulation are evaluated. Cable cylindrical insulation is first divided into sufficiently small segments whose temperatures are simulated by jointly using a finite volume method and an artificial neural network to model the thermal ageing experiment conditions. The thermal degradation of IR is then simulated by dichotomy models that randomly sample fully degraded segments based on an overall insulation (layer) ageing condition estimation and discretization models that estimate the gradual degradation of individual segments, respectively. Furthermore, uniform and non-uniform temperature profiles are incorporated into dichotomy and discretization models, respectively, for a comparison. The IR simulation results are not only compared between different models, but also discussed around the sensitivity of IR simulation to segment sizes and degradation rates. This provides cable assessment engineers with insights into model behaviour as a reference for their selection of appropriate IR degradation models. [ABSTRACT FROM AUTHOR]

This paper designs a multi-variable hybrid islanding-detection method (HIDM) using signal-processing techniques. The signals of current captured on a test system where the renewable energy (RE) penetration level is between 50% and 100% are processed by the application of the Stockwell transform (ST) to compute the Stockwell islanding-detection factor (SIDF) and the co-variance islanding-detection factor (CIDF). The signals of current are processed by the application of the Hilbert transform (HT), and the Hilbert islanding-detection factor (HIDF) is computed. The signals of current are also processed by the application of the Alienation Coefficient (ALC), and the Alienation Islanding Detection Factor (AIDF) is computed. A hybrid islanding-detection indicator (HIDI) is derived by multiplying the SIDF, CIDF, AIDF, and an islanding weight factor (IWF) element by element. Two thresholds, designated as the hybrid islanding-detection indicator threshold (HIDIT) and the hybrid islanding-detection indicator fault threshold (HIDIFT), are selected to detect events of islanding and also to discriminate such events from fault events and operational events. The HIDM is effectively tested using an IEEE-13 bus power network, where solar generation plants (SGPs) and wind generation plants (WGPs) are integrated. The HIDM effectively identified and discriminated against events such as islanding, faults, and operational. The HIDM is also effective at identifying islanding events on a real-time distribution feeder. The HIDM is also effective at detecting islanding events in the scenario of a 20 dB signal-to-noise ratio (SNR). It is established that the HIDM has a small non-detection zone (NDZ). The effectiveness of the HIDM is better relative to the islanding-detection method (IDM) supported by the discrete wavelet transform (DWT), an IDM using a hybridization of the slantlet transform, and the Ridgelet probabilistic neural network (RPNN). An IDM using wavelet transform multi-resolution (WT-MRA)-based image data and an IDM based on the use of a deep neural network (DNN) were used. The study was performed using the MATLAB software (2017a) and validated in real-time using the data collected from a practical distribution power system network. [ABSTRACT FROM AUTHOR]

NOx is one of the main sources of pollutants for motor vehicles. Nowadays, many diesel vehicle manufacturers may use emission-cheating equipment to make the vehicles meet compliance standards during emission tests, but the emissions will exceed the standards during actual driving. In order to strengthen the supervision of diesel vehicles for emission monitoring, this article intends to establish a model that can predict the transient emission characteristics of heavy-duty diesel vehicles and provide a solution for remote online monitoring of diesel vehicles. This paper refers to the heavy-duty vehicle National VI emission regulations and uses vehicle-mounted portable emission testing equipment (PEMS) to conduct actual road emission tests on a certain country's VI heavy-duty diesel vehicles. Then, it proposes a new feature engineering processing method that uses gray correlation analysis and principal component analysis to eliminate invalid data and reduce the dimensionality of the aligned data, which facilitates the rapid convergence of the model during the training process. Then, a double-hidden-layer BP (Back propagation) neural network was established, and the improved gray wolf algorithm was used to optimize the threshold and weight of the neural network, and a heavy-duty diesel vehicle NOx emission prediction model was obtained. Through the training of the network, the root mean square error (RMSE) of the improved model on the test set between the predicted value and the true value is 1.9144 (mg/s), and the coefficient of determination (R2) is 0.87024. Compared with single-hidden-layer network and double-hidden-layer BP neural network models, the accuracy of the model has been improved. The model can well predict the actual road NOx emissions of heavy-duty diesel vehicles. [ABSTRACT FROM AUTHOR]

A fuel cell is an energy conversion device that utilizes hydrogen energy through an electrochemical reaction. Despite their many advantages, such as high efficiency, zero emissions, and fast startup, fuel cells have not yet been fully commercialized due to deficiencies in service life, cost, and performance. Efficient evaluation methods for performance and service life are critical for the design and optimization of fuel cells. The purpose of this paper was to review the application of common machine learning algorithms in fuel cells. The significance and status of machine learning applications in fuel cells are briefly described. Common machine learning algorithms, such as artificial neural networks, support vector machines, and random forests are introduced, and their applications in fuel cell performance prediction and optimization are comprehensively elaborated. The review revealed that machine learning algorithms can be successfully used for performance prediction, service life prediction, and fault diagnosis in fuel cells, with good accuracy in solving nonlinear problems. Combined with optimization algorithms, machine learning models can further carry out the optimization of design and operating parameters to achieve multiple optimization goals with good accuracy and efficiency. It is expected that this review paper could help the reader comprehend the state of the art of machine learning applications in fuel fuels and shed light on further development directions in fuel cell research. [ABSTRACT FROM AUTHOR]

Short-term load forecasting (STLF) is critical for the energy industry. Accurate predictions of future electricity demand are necessary to ensure power systems' reliable and efficient operation. Various STLF models have been proposed in recent years, each with strengths and weaknesses. This paper comprehensively reviews some STLF models, including time series, artificial neural networks (ANNs), regression-based, and hybrid models. It first introduces the fundamental concepts and challenges of STLF, then discusses each model class's main features and assumptions. The paper compares the models in terms of their accuracy, robustness, computational efficiency, scalability, and adaptability and identifies each approach's advantages and limitations. Although this study suggests that ANNs and hybrid models may be the most promising ways to achieve accurate and reliable STLF, additional research is required to handle multiple input features, manage massive data sets, and adjust to shifting energy conditions. [ABSTRACT FROM AUTHOR]

Energy systems around the world are going through tremendous transformations, mainly driven by carbon footprint reductions and related policy imperatives and low-carbon technological development. These transformations pose unprecedented technical challenges to the energy sector, but they also bring opportunities for energy systems to develop, adapt, and evolve. With rising complexity and increased digitalization, there has been significant growth in the amount of data in the power/energy sector (data ranging from power grid to household levels). Utilization of this large data (or "big data"), along with the use of proper data analytics, will allow for useful insights to be drawn that will help energy systems to deliver an increased amount of technical, operational, economic, and environmental benefits. This paper reviews various categories of data available in the current and future energy systems and the potential benefits of utilizing those data categories in energy system planning and operation. This paper also discusses the Big Data Analytics (BDA) that can be used to process/analyze the data and extract useful information that can be integrated and used in energy systems. More specifically, this paper discusses typical applications of BDA in energy systems, including how BDA can be used to resolve the critical issues faced by the current and future energy network operations and how BDA contributes to the development of smarter and more flexible energy systems. Combining data characterization and analysis methods, this review paper presents BDA as a powerful tool for making electrical energy systems smarter, more responsive, and more resilient to changes in operations. [ABSTRACT FROM AUTHOR]

In this paper, a set of best practice data sharing guidelines for wind turbine fault detection model evaluation is developed, which can help practitioners overcome the main challenges of digitalisation. Digitalisation is one of the key drivers for reducing costs and risks over the whole wind energy project life cycle. One of the largest challenges in successfully implementing digitalisation is the lack of data sharing and collaboration between organisations in the sector. In order to overcome this challenge, a new collaboration framework called WeDoWind was developed in recent work. The main innovation of this framework is the way it creates tangible incentives to motivate and empower different types of people from all over the world to share data and knowledge in practice. In this present paper, the challenges related to comparing and evaluating different SCADA-data-based wind turbine fault detection models are investigated by carrying out a new case study, the "WinJi Gearbox Fault Detection Challenge", based on the WeDoWind framework. A total of six new solutions were submitted to the challenge, and a comparison and evaluation of the results show that, in general, some of the approaches (Particle Swarm Optimisation algorithm for constructing health indicators, performance monitoring using Deep Neural Networks, Combined Ward Hierarchical Clustering and Novelty Detection with Local Outlier Factor and Time-to-failure prediction using Random Forest Regression) appear to exhibit high potential to reach the goals of the Challenge. However, there are a number of concrete things that would have to have been done by the Challenge providers and the Challenge moderators in order to ensure success. This includes enabling access to more details of the different failure types, access to multiple data sets from more wind turbines experiencing gearbox failure, provision of a model or rule relating fault detection times or a remaining useful lifetime to the estimated costs for repairs, replacements and inspections, provision of a clear strategy for training and test periods in advance, as well as provision of a pre-defined template or requirements for the results. These learning outcomes are used directly to define a set of best practice data sharing guidelines for wind turbine fault detection model evaluation. The guidelines can be used by researchers in the sector in order to improve model evaluation and data sharing in the future. [ABSTRACT FROM AUTHOR]

This paper presents a model for determining fuzzy evaluations of partial indicators of the availability of continuous systems at coal open pits using a neuro-fuzzy inference system. The system itself is a combination of fuzzy logic and artificial neural networks. The system availability is divided into partial indicators. By combining the fuzzy logic and artificial neural networks, a model is obtained that has the ability to learn and uses expert judgment for that learning. This paper deals with the ECC system (bucket wheel excavator-conveyor-crushing plant) of the open pit Drmno-Kostolac, which operates within the Electric Power Company of Serbia. The advantage of a model of this type is that it does not rely on the historical experiences of experts and usual predicted values for the fuzzy evaluation of partial indicators, which are based on the assumption that similar systems affect availability in a similar way. The fuzzy evaluation of partial indicators is based on historical data for the specific system for which the model was created. As such, it can more accurately predict continuous systems availability on the basis of expert evaluations in the appropriate time period. Another advantage of this model is that the availability is estimated on a quarterly basis, which gives a more accurate view because it uses a smaller time period with more similar characteristics and, thus, includes certain external influences which are related to the quarterly meteorological conditions. [ABSTRACT FROM AUTHOR]

This paper presents an approach to estimate demand in the Polish Power System (PPS) using the historical electricity usage of 27 thousand commercial customers, observed between 2016 and 2020. The customer data were clustered and samples as well as features were created to build neural network models. The goal of this research is to analyze if the clustering of customers can help to explain demand in the PPS. Additionally, considering that the datasets available for commercial customers are typically much smaller, it was analyzed what a minimal sample size drawn from the clusters would have to be in order to accurately estimate demand in the PPS. The evaluation and experiments were conducted for each year separately; the results proved that, considering adjusted R2 and mean absolute percentage error, our clustering-based method can deliver a high accuracy in the load estimation. [ABSTRACT FROM AUTHOR]

Continual learning has recently become a primary paradigm for deep neural network models in modern artificial intelligence services, where streaming data patterns frequently and irregularly change over time in dynamic environments. Unfortunately, there is still a lack of studies on computing cluster management for the processing of continual learning tasks, particularly in terms of the timeliness of model updates and associated energy consumption. In this paper, we propose a novel timeliness-aware continual learning management (TA-CLM) system aimed at ensuring timely deep neural network model updates for continual learning tasks while minimizing the energy consumption of computing worker nodes in clusters. We introduce novel penalty cost functions to penalize quantitatively deep neural network model update latency and present the associated optimization formulation to ensure the best task allocation. Additionally, we design a simulated annealing-based optimizer, which is a meta-heuristic technique and easy to implement, to solve the non-convex and non-linear optimization problem. We demonstrate that the proposed TA-CLM system improves both latency and energy performance over its competitors by an average of 51.3% and 51.6%, respectively, based on experimental results using raw data from well-known deep neural network models on an NVIDIA GPU-based testbed and a large-scale simulation environment. [ABSTRACT FROM AUTHOR]

For equivalent modeling of mixed wind farms (WFs), existing clustering indicators cannot consider the complex coupling characteristics between different types of wind turbines (WTs). In this paper, a refined equivalent modeling approach based on artificial intelligence technology is proposed. Firstly, the electromechanical transient performance of mixed WFs is analyzed. The WT type, wind speed and direction, and voltage dip are considered the dominant factors affecting the external dynamic response of mixed WFs. Secondly, the equivalent node model is established, including the selection of independent and dependent variables. Then, the multiple artificial neural networks (ANNs) are trained one by one based on small sample data, to fit the nonlinear relationship between the dependent variables and the independent variables. Finally, the dynamic response of the power systems with a mixed WF is simulated in the MATLAB platform. A comparison of the errors in electromechanical phenomena demonstrates that the proposed model can reflect the external characteristics of the test mixed WF in different wind conditions and voltage dips. [ABSTRACT FROM AUTHOR]

Confronted with the climate crisis, the world is making tremendous efforts in energy transition, such as expanding renewable energy that does not emit carbon. The importance of virtual power plant (VPP) operation technology has emerged to secure grid flexibility in response to the expanding renewable energy implemented due to these efforts. Accordingly, VPPs, which include photovoltaics, wind turbines, heating, ventilation, and air conditioning (HVAC), load, and EV, have been constructed. HVAC, one of the component resources, is a system that controls and regulates temperature, humidity, and airflow. Since it responds sensitively to the building's heat capacity and changes in the external environment, it requires continuous and stable control. In this paper, we used data-based modeling to implement the HVAC required for the optimal operation of VPP. Since accurately creating an equation-based HVAC model was difficult considering building information modeling and external environment variables, we used historical HVAC operation data to perform data-based modeling. The model was implemented using nonlinear regression and machine learning, such as a support vector machine and artificial neural network. Then, the data-based HVAC and the actual HVAC operation results were comparatively analyzed based on a case study, and the model's goodness-of-fit was evaluated based on performance metrics. Model performance indicators confirmed that the ANN-based HVAC model was most similar to the actual HVAC system. [ABSTRACT FROM AUTHOR]